Tech Unit No: 0620000004 Revision: C Approved By: Quality Engineer Date: 201-1-9 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical Setting Tools to cover a large range of casing weight The upper slips are held in a safe retracted position while running Allows users to set, pressure test tubing, and squeeze in a single trip Can quickly be configured to set MMR Cement Retainers or MMB Bridge Plugs These tools can be used to run a number of competitive brand Baker style cement retainers or bridge plugs O.D. (in) CASING WT. (lbs) 4-1/2 9.-1.1 11.-20.8 SETTING SLEEVE O.D. (in) 3.93-1/2 13-23 4.310-3/4 14-26 4.700 6-/8 17-32.37 7 17-3.687 7-/8 20-39 6.312 8-/8 24-49 7.12 9-/8 29.3-8.4 8.12 10-3/4 32.7-60.7 9.430 11-3/4 60-83 9.937 38-60 10.437 13-3/8 48-80.7 11.880 16 6-118 14.12 20 94-133 18.37 TOOL I.D. (in) 0.87 1.2 STANDARD BOX UP 2-3/8 EU 8 RD 2-7/8 EU 8 RD 1
General Operation: When it is advantageous to run a Map Oil Tools Cement Retainer on tubing or drill pipe, a mechanical setting tool is used. It is designed to contain the upper slips of the cement retainer in a safe retracted position while running to setting depth. The upper slips are released by right hand rotation and slack off of the work string. The cement retainer is then set and locked to the casing by pulling the appropriate amount of tension against the tool. The slide valve is in the open position while being run into the hole. When the setting procedure is completed, the slide valve may be closed by picking up (2) two inches at the tool or opened by slacking off (2) two inches at the tool. With the slide valve in the closed position, the work string may be hydraulically tested. The mechanical running tool is released from the cement retainer by right hand rotation. The setting tool contains a built in snap-out feature which provides approximately,000 # snap out indication when the work string is picked up to close the valve. This tension indicator is reengaged each time the work string is lowered to open the slide valve. The mechanical setting tool is equipped with drag springs to assure positive control during running and setting procedures at all depths or in highly deviated wells. The mechanical setting tool may be converted from use with a cement retainer to a bridge plug by changing the top coupling, stinger sub, and removing the stinger seal. Special Notes: It is recommended to run a gage ring, bit, and casing scraper to setting depth, then circulate two full casing columns to clear debris from the wellbore. When there is possibility that you will have difficulty stabbing back in to the retainer due to wellbore deviation, it is recommended that centralizers be run above the mechanical setting tool. If wellbore fluids or debris may be present, it is recommended that rotational release occur after completing pumping operations as debris that falls into the ID of the tool may prevent the valve from functioning properly and may prevent the setting tool from stinging back into the tool. Running Instructions: 1. Make up the top sub of the running tool to the lower pin end of the work string. Use a good quality, API approved thread lubricant and torque all work string connections to the manufacturer s torque recommendations. During run in, extreme care should be taken to avoid right hand rotation being transmitted to the setting tool. As a precaution, one left hand turn should be placed in the work string every 10-1 stands. 2. When the desired setting depth has been reached, tools should be picked up (2) two feet above the desired setting point. This movement is necessary to provide the required tool stroke to release the cement retainer upper slips and allow the setting tool nut to move freely. 3. Rotate the work string to the right sufficiently to transmit 10 turns to the tool. This rotation will thread the control nut off of the mandrel s mating thread and release the control sleeve and setting sleeve form the controlled position. 4. Lower the tools back down to the desired setting point, the drag springs will support the control sleeve and setting sleeve of the setting tool. The downward motion of the mandrel will move the cement retainer upper slips form under the setting sleeve. The slips are forced outward toward the casing wall by the leaf springs inside of each slip segment. When the slips are released, there is sufficient clearance for the locking dog to move outward and release the control latch form the stinger sub body.. Pull the recommended tension over pipe weight (at the tools) to set the slips and affect full pack off. SIZE TOOL MIN. TENSION MAX. TENSION 4 1/2-1/2 2,000 30,000 6 /8-7 3,000 4,000 7 /8-20 40,000,000 6. Set down the equivalent amount of weight and pull tension a second time. Once the tool is set, slight up strain may be applied to shift the valve closed, at which point the tubing can be tested. 2
7. Release the setting tool from the cement retainer by pulling 00 lbs. of tension at the tool and rotating the work string 10 turns to the right. This motion will shear the brass shear screws and unscrew the setting tool control latch from the top of the cement retainer mandrel. 8. The setting tool may be re-latched to the cement retainer by setting down 1000-3000 lbs. of work string weight. Set down weight equal to the calculated weight required to prevent the slide valve from closing during pumping operations. Always hold and monitor 200 psi pressure on the annulus while squeezing through a cement retainer. Recommended max flow rate is bpm. Higher flow rates may be achieved, but variations in pump volume, fluid density, fluid viscosity and pump rates will have varying effects on stinger and retainer shoe wash out which may result in the retainer s inability to close and isolate wellbore pressure below the tool. 9. Now you may snap out of the retainer by pulling 000-8000 lbs. tension at the tool. The setting tool seal will remain in the cement retainer until the control snap force is exceeded. Each time the control latch is snapped in and out of the retainer, the force required to do so will be reduced until the force to snap in reaches 00 lbs. and the force to snap out reaches,000 lbs. SPECIAL NOTE: In wells where paraffin or suspended solids are present in the well bore fluids, the dog in the control latch may not fully release from the stinger sub body. This is indicated when the cement retainer sets properly, per steps 1 thru 4, but the slide valve will not close so that a tubing pressure test can be performed. In this case, the tubing should be alternately picked up and slacked off. This motion will cause the dog to move outward on the inclined edges of the control groove in the stinger sub body and free it for the required vertical motion. If this condition is known to exists before the run is made, it is recommended that the mandrel, stinger sub body, control latch, and control sleeve be packed with grease to prevent the intrusion of trouble fluids. Mounting the Mechanical Set Cement Retainer to the Mechanical Setting Tool: 1. Place the top collar of the setting tool in the vise. 2. Move the drag assembly downward until it positions the control nut clutch and the control nut adjacent to one another. Rotate the mechanism to the right until it engages the clutch and stops. 3. Rotate the setting sleeve toward the drag assembly until the upset of the control latch is exposed. 4. Slide the upper slips over the stinger sub body. Loosen the clamp on the slips only enough to slide them over the upset on the control latch and then retighten the clamp.. Lubricate the non-wicker portion of the slips with grease. Rotate the setting sleeve downward over the slips until the setting sleeve contacts the hose clamp. Remove the clamp from the slips and continue rotating the setting sleeve downward until it bottoms out against the wickers of the slips. Back the setting sleeve off 3 turns. Check to see that the clutch mechanism is still properly shouldered. Readjust the setting sleeve, if necessary. 6. Lubricate the stinger sub and latch lightly with grease. 7. Slide the cement retainer over the stinger. (Make sure that the retainer remains level during this operation. Special care must be taken to ensure that the stinger properly engages the valve collet fingers.) Drive the retainer on to the stinger seal until it shoulders on the latch thread.(use a wooden block for this operation.) Bump the bottom of the retainer and rotate it to the make up the LEFT HAND thread on the latch until the retainer bottoms out on the control latch. 8. Align the threaded holes of the retainer body with the corresponding holes in the control latch and install the shear screws. (4 1/2-6 /8 there is only one set of holes, 7-8 /8 will used lower holes, 9 /8 on up will use upper holes.) 9. Rotate the setting sleeve downward until it contacts the wickers of the slips. Back up ½ turn and install the set screws in the setting sleeve. 10. Install the hose clamp about the wickers of the upper slips and tighten for transportation purposes. REMOVE THE HOSE CLAMP FROM THE SLIPS BEFORE RUNNING THE TOOLS INTO THE WELL 3
Mechanical Setting Tool Casing OD (in) Casing Weight Range (lbs) MSB For use with MWR and MWB-1 MSR For use with MMR and MMB KG Approx. Weight LBS 4-1/2 9.-1.1 11.-20.8 062039004 06203900 4 100-1/2 13-23 0620431004 062043100 30 66-3/4 14-26 0620470004 062047000 42 93 6-/8 17-32 062037004 06203700 72 18 7 17-3 062068004 06206800 80 176 7-/8 20-39 0620631004 062063100 7 16 8-/8 24-49 0620712004 062071200 80 176 9-/8 29.3-8.4 0620812004 062081200 110 242 10-3/4 32.7-60.7 0620943004 062094300 12 27 11-3/4 60-83 0620994004 062099400 13 297 38-60 0621043004 062104300 148 326 13-3/8 48-80.7 0621188004 062118800 170 374 16 6-118 0621412004 062141200 19 430 20 94-133 0621837004 062183700 290 638 4
Model "MSR" Mechanical Setting Tool Part List 4 ½ ¾ Item Description Qty Size and Part Number 4 1/2" & " 1/2" 3/4" 06203900 062043100 062047000 1 COUPLING 1 062043100 2 MANDREL 1 062043102 3 UPPER DRAG COLLAR 1 062043103 4 UPPER DRAG RING 1 062043104 SOCKET HEAD SCREW 3 04602296 6 DRAG SPRING 6 01480083 0620431083 7 RETAINER 1 X20-2-118 8 LOWER DRAG RING 1 062043104 9 LOWER DRAG COLLAR 1 06204310 10 CONTROL SLEEVE 1 0620431060 11 SOCKET HEAD SCREW 4 04602096 12 SOCKET HEAD SCREW 3 04602296 13 SOCKET HEAD SCREW 2 0460077 04602697 14 CONTROL NUT ASSY. 1 0620431061 1 CONTROL NUT CLUTCH 1 0620431062 16 RETAINING SLEEVE 1 0620431063 17 O-RING 1 000P69219 18 SOCKET HEAD SCREW 2 0800000336 19 DOG 1 0620431064 20 DOWEL PIN 2 062068073 21 SPRING 2 0620431173 22 SETTING SLEEVE 1 06203906 062043106 062047006 23 CONTROL LATCH 1 0620431068 24 KEY 1 062068067 2 STINGER SUB BODY 1 0620431069 26 SEAL 1 0148008 27 O-RING 1 000P69024 28 SLIDING VALVE STINGER 1 0620431070 29 PIN THREAD PROTECTOR 1 09600301 30 SEAL REDRESS KIT NA 062039200 31 SCREW REDRESS KIT NA 06203920 32 CONVERSION KIT TO MSB NA 062043114
Item Description Qty 6 /8-20 Model "MSR" Mechanical Setting Tool Part List 6 /8" 7" 7 /8" 8 /8" 9 /8" 10 3/4" Size and Part Number 11 3/4" 60-83# 11 3/4" 38-60# 13 3/8" 16" 20" 06203700 06206800 062063100 062071200 062081200 062094300 062099400 062104300 062118800 062141200 062183700 1 COUPLING 1 06206800 2 MANDREL 1 06206802 3 UPPER DRAG COLLAR 1 06206803 062063103 062071203 062094303 062099403 062118803 062141203 062183703 4 UPPER DRAG RING 1 06206804 06206310 062071204 062094304 062099404 062118804 062141204 062183704 SOCKET HEAD SCREW See Size 04602296 (Qty: 43) 04602296 (Qty: 6) 6 DRAG SPRING 6 062043108 062068083 06207120 062081206 062071206 062081206 062081206 (Qty: 9) 7 RETAINER 1 3 6 X20-2-116 8 LOWER DRAG COLLAR 1 0620680 06206310 06207120 06209430 06209940 06211880 06214120 06218370 9 SNAP RING 1 06206807 10 LOWER DRAG RING 1 06206806 06206310 062071204 062094304 062099404 062118804 062141204 062183704 11 DRAG COLLAR INSERT 1 6 06206808 12 SOCKET HEAD SCREW 4 04602297 04674091 13 RETAINING WASHER 1 06206809 14 CONTROL SLEEVE 1 062068060 1 CONTROL NUT ASSY. 1 062068061 16 SOCKET HEAD SCREW 2 0460077 04602697 046007 04602697 17 CONTROL NUT CLUTCH 1 062068062 18 O-RING 1 000P6922 19 SOCKET HEAD SCREW 2 0800000336 20 RETAINING SLEEVE 1 062068063 Continued on next page 6
6 /8-20 Model "MSR" Mechanical Setting Tool Part List - continued Item Description Qty 6 /8" 7" 7 /8" 8 /8" 9 /8" 10 3/4" Size and Part Number 11 3/4" 60-83# 11 3/4" 38-60# 13 3/8" 16" 20" 06203700 06206800 062063100 062071200 062081200 062094300 062099400 062104300 062118800 062141200 062183700 21 DOG 1 062068064 22 SETTING SLEEVE 1 06206806 062063106 062071206 062081206 062094306 062099406 062104306 062118806 062141206 062183706 23 KEY 1 062068067 24 DOWEL PIN 2 062068073 2 SLIP ADAPTER 1 Not Required 0620631069 0620712069 0620812069 0620943069 0620994069 0621043069 0621188069 0621412069 062183709 26 SOCKET HEAD SCREW 4 Not Required 0463296 0620712070 0620812070 X20-0-43 0621188070 04602493 0621412070 0620812070 27 SPRING 2 01884060 28 SPACER 4 Not Required 0620712074 Not Required 0620712074 Key - 0621837064 Qty. - 2 29 CONTROL LATCH 1 062068068 0620631068 0621837068 30 STINGER SUB BODY 1 062068069 31 SEAL 1 0148408 32 O-RING 1 000P69130 33 SLIDING VALVE STINGER 1 062068070 34 PIN THREAD PROTECTOR 1 09600303 3 SEAL REDRESS KIT NA 062068200 36 SCREW REDRESS KIT NA 06206811 37 CONVERSION KIT TO MSB NA 06206814 7
6 /8 7 /8 Model MSR Mechanical Setting Tool 8 /8 11 3/4 60-83# Model MSR Mechanical Setting Tool 11 3/4 38-60# 13 3/8 Model MSR Mechanical Setting Tool 16 20 Model MSR Mechanical Setting Tool 8
Conversion from MSR Cement Retainer Mechanical Setting Tool to MSB Bridge Plug Mechanical Setting Tool 1. Change the Top Coupling to Ported Top Coupling. 2. Remove the Stinger, Seal and the O-ring under the Seal. 3. Install the Spacer on where the Seal was. 4. Install the Thread Protector on the bottom thread where the Stinger connected to. Reverse the above steps to convert MSB to MSR. PN# Tool Size 4 1/2" 3/4" 6 /8" 20" Complete Conversion Kit 062043114 06206814 Ported Top Coupling 062043101 062068084 Spacer 0620431079 062068087 Thread Protector 0620431080 062068086 9
4 ½-, ½, ¾ MSR Assembly Instructions 4 1/2", 1/2" and 3/4" Mechanical Setting Tool. 1. Thread Control Nut Clutch (1) onto threads on lower end or Mandrel (2) until it shoulders out. 2. Thread Control Nut Assembly (14) onto control threads until clutch surface of Control Nut and Control Nut Clutch engage. 3. Slide Lower Drag Ring (8) and Lower Drag Collar (9) over mandrel. 4. Slide Tru-Arc Retainer (7) over the Mandrel and locate into groove.. Slide Upper Drag Collar (3) and Drag Ring onto Mandrel. Insert Drag Springs into slots on Upper Drag Collar and slide Drag Ring over Drag Springs. Align holes and install Cap Screws (). 6. Insert Drag Springs (6) into slots on Lower Drag Collar and slide Drag Ring over Collar and Springs. Install Cap Screws (12) into mating holes of Lower Drag Collar and Lower Drag Ring. 7. Thread Coupling (1) onto Mandrel. Place Coupling in a vise and tighten Mandrel to Coupling connection with a pipe wrench. Place wrench in the under cut wrenching area on Mandrel. 8. Slide Retaining Sleeve (16) through Control Sleeve (10) and engage Retaining Sleeve upper external shoulder with Control Sleeve's lower internal shoulder. 9. Align internal keyway in Control Sleeve with key on Control Nut and slide Control Sleeve up over Control Nut and Mandrel until Retaining Sleeve shoulder is against Control Nut. 10. Make-up Lower Drag Collar into Control Sleeve hand tight. Unscrew Lower Drag Collar out until threaded holes for Cap Screws (11) can be seen through mating holes in Control Sleeve. Install Cap Screws and tighten. Care should be taken during this procedure to prevent the Control Nut from backing off. 11. Screw Setting Sleeve (22) onto Control Sleeve until Setting Sleeve upper end contacts the upset on Control Sleeve. 12. Coat Dog Springs (21) with grease and insert into appropriate holes in Control Latch (23). Insert Dog (19), Dowel Pins (20) and Set Screws (18) into Control Latch. Be sure that the Dowel Pins trap the Dog in the Control Latch. 10
13. Place Key (24) into vertical slot on Stinger Sub Body (2). Align keyway in Control Latch with Key and slide Control Latch onto Stinger Sub Body. Install O-ring (17) on Stinger Sub Body. Align and depress Dog into locking groove of Stinger Sub Body and make up into the lower end of the Mandrel. The Dog must move under the Retaining Sleeve as the Stinger Sub Body and Mandrel are made up. Make up wrench tight. 14. Insert O-ring (27) into groove inside of Stinger Seal (26). Install Stinger Seal on Stinger Sub Body. Install Slide Valve Stinger (28) on Stinger Sub Body. Make up wrench tight 1. Screw Setting Sleeve (22) down onto control Sleeve and install Set Screws (13). 16. Double check Control Nut Assembly is bottomed out on the Control Nut Clutch by spinning the Drag Springs to the (RIGHT) with the Coupling still held in the vise. Disassembly Instructions 4 1/2", 1/2" and 3/4" Mechanical Setting Tool. 1. Clamp Coupling (1) in vise. Loosen and remove Slide Valve Stinger (28) from Stinger Sub Body (2). Remove Stinger Seal (26) and O-Ring (27). 2. Loosen and remove Stinger Sub Body/Control Latch subassembly from the Mandrel (2). Remove O-Ring (17) and slide Control Latch (23) off of Stinger Sub Body. 3. Remove Set Screws (18) from Control Latch. Turn Control Latch upside down and depress Dog (19) to remove Dowel Pins (20). Remove Dog and Springs (21). 4. Remove Set Screws (13) from Setting Sleeve (22) and unscrew Setting Sleeve from Control Sleeve (10).. Remove Cap Screws (11) and unscrew Lower Drag Collar (9) from Control Sleeve and remove Control Sleeve. Remove Retaining Sleeve (16) from Control Sleeve. 6. Remove Cap Screws () from Upper Drag Collar (3) and slide Upper Drag Ring (4) off of Upper Drag Collar. 7. Remove Cap Screws (12) from Lower Drag Collar (9) and slide Lower Drag Ring (8) off and remove Drag Springs (6). 8. Loosen Mandrel (2) from Coupling. Place wrench in under cut on Mandrel. 9. Remove Tool from Vise and Remove Coupling (1). 10. Remove Upper Drag collar and Upper Drag Ring from Mandrel. Remove Tru-Arc Retainer (7). 11. Remove Lower Drag Collar from Mandrel. 12. Remove Control Nut Assembly (14). Do not remove Control Nut Clutch (1) unless required. 11
Assembly Instructions 6 /8 20 Mechanical Setting Tool 1 0*3j # 2j BHG 6 /8-20 MSR 1. Thread Control Nut Clutch (17) onto threads on lower end of Mandrel (2) until it shoulders out. 2. Thread Control Nut Assembly (1) onto control threads until clutch surface of Control Nut and Control Nut Clutch engage. 3. Slide Retaining Washer (13), Drag Collar Insert (11) (large ID down) and Snap Ring (9) over Mandrel. Depress Snap Ring into groove on Mandrel with a hose clamp or Chain Vise Grip. Slide small ID of Drag Collar Insert over Snap Ring and remove hose clamp. Leave top of Snap Ring and top of the Drag Collar Insert flush. 4. Slide Lower Drag Ring (10) and Lower Drag Collar (8) onto Mandrel. Slide Lower Drag Collar over Drag Collar Insert until Drag Collar Insert is seated in counter bore of Lower Drag Collar. This will trap the Snap Ring in the recess of the Mandrel.. Slide Tru-Arc Retainer (7) over the Mandrel and locate into groove. 6. Slide Upper Drag Collar (3) and Upper Drag Ring (4) onto Mandrel. 7. Thread Coupling (1) onto Mandrel. Place Coupling in a vise and tighten Mandrel to Coupling connection with a pipe wrench. Place wrench in the under cut wrenching area on Mandrel. 8. Insert Drag Springs (6) into slots on Lower Drag Collar and slide Lower Drag Ring over Drag Springs. Align holes and install Cap Screws (). 9. Insert Drag Springs into slots on Upper Drag Collar and slide Upper Drag Ring over Drag Springs. Align holes and install Cap Screws (). 10. THIS STEP FOR 6 /8-7 ONLY. Seat Retaining Washer (13) against matching shoulder inside Control Sleeve. 11. Make up Lower Drag Collar into Control Sleeve hand tight. Unscrew Lower Drag Collar out until threaded holes for Cap Screws (12) can be seen through the mating holes in Control Sleeve. Install Cap Screws and tighten. Care should be taken during this procedure to prevent the Control Nut from backing off. 12
12. Screw Setting Sleeve (22) onto Control Sleeve (14) until Setting Sleeve upper end contacts the upset on Control Sleeve. 13. Coat Dog Springs (27) with grease and insert into appropriate holes in Control Latch (29). Insert Dog (21), Dowel Pins (24) and Set Screws (19) into Control Latch. Be sure that the Dowel Pins trap the Dog in the Control Latch. 14. THIS STEP FOR 7 /8 20 ONLY. Install Slip Adapter (2) and secure with Flat Head Screws (26). 1. Place Key (23) into vertical slot on Stinger Sub Body (30). Align keyway in Control Latch with Key and slide Control Latch onto Stinger Sub Body. Install O-ring (18) on Stinger Sub Body. Align and depress Dog into locking groove of Stinger Sub Body and make up into the lower end of the Mandrel. The Dog must move under the Retaining Sleeve as the Stinger Sub Body and Mandrel are made up. Make up wrench tight. 16. THIS STEP FOR 8 /8-11 ¾ 60-83# & 16. THE 20 TOOL USES 2EA KEYS. Install Spacers (28) in to slot on Control Latch with the long bevel facing the collet side of the Control Latch. 17. THIS STEP FOR 7 /8 20. Install Slip Adapter (2) over Spacers onto Control Latch and secure with Socket Head Screws (26) 18. Insert O-ring (32) into groove inside of Stinger Seal (31). Install Stinger Seal on Stinger Sub Body. Install Slide Valve Stinger (33) on Stinger Sub Body. Make up wrench tight. 19. Screw Setting Sleeve back down onto Control Sleeve and install Set Screws (16). 20. Confirm that the Control Nut Assembly is bottomed out on the Control Nut Clutch by spinning the Drag Springs to the right with the Coupling still held in the vise. Disassembly Instructions 6 /8-20 Mechanical Setting Tool 1. Clamp Coupling (1) in vise. Loosen and remove Slide Valve Stinger (33) from Stinger Sub Body (30). Remove Stinger Seal (31) and O-ring (32). 2. Loosen and remove Stinger Sub Body/Control Latch subassembly from the Mandrel (2). Remove O- ring (18) and slide Control Latch (29) off Stinger Sub Body. 3. Remove Key (23) from Stinger Sub Body. 4. EXCLUDE THIS STEP FOR 6 /8-7. Remove Socket Head Screws (26) and Slip Adapter (2). Slide Slip Adapter off of Control Latch. EXCLUDE THIS STEP FOR 6 /8-7 /8, 11 ¾ 38-60#, & 13 3/8. THE 20 USES 2EA KEYS. Remove Spacers (28) from Control Latch. 13
6. Remove Set Screws (19) from Control Latch. Turn Control Latch upside down and depress Dog (21) to remove Dowel Pins (24). Remove Dog and Springs (27). 7. Remove Set Screws (16) from Setting Sleeve (22) and unscrew Setting Sleeve from Control Sleeve (14). 8. Remove Cap Screws (12) and unscrew Lower Drag Collar (8) from Control Sleeve and remove Control Sleeve. Remove Retaining Sleeve (20) from Control Sleeve. 9. Remove Cap Screws () from Lower Drag Collar then slide Lower Drag Ring (10) off. 10. Remove Cap Screws () from Upper Drag Collar (3) and slide Upper Drag Ring (4) off. Remove Drag Springs (6). 11. Loosen Mandrel from Coupling. Place wrench in under cut on Mandrel. Remove Coupling. 12. Remove Upper Drag collar and Upper Drag Ring from Mandrel. Remove Tru-Arc Retainer (7). 13. Remove Lower Drag Collar and Lower Drag Ring from Mandrel. Remove Snap Ring (9), Drag Collar Insert (11) and Retaining Washer (13). 14. Remove Control Nut Assembly (1). Do not remove Control Nut Clutch (17) unless required. 14