SETION 1 STNR INSTLLTION 1/4" FRME PNELS 3/4" OVERLY PNELS SETION 2 INSTLLTION
OVERLL IMENSIONS STNR INSTLLTION 25 1/8" (63.8) 36" (91.5) 23 7/8" (60.7) 1 7/8" (4.8) *84" (213.4) *83 1/2" (212.1) 69 5/8" (176.8) *73 1/4" (186.1) SPEIFITIONS Overall Width Overall Height Overall epth learance utout Width 36" (91.4 cm) 84" (213.4 cm) 25 3/8" (64.45 cm) 36 3/4" (93.4 cm) 35 1/2" (90.2 cm) utout Height 83 1/2" - 84 1/2" (212.1-214.6 cm) utout epth Plumbing Requirements Shipping Weight 24" (61 cm) 1/4" O copper tubing or GE Smartonnect kit 569 lb *3" (7.6) FRONT VIEW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. 35" (89.0) ase width *3 1/4" (8.3) ** llow 25" (63.5) min clearance for 130 door swing SIE VIEW TTENTION ELETRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. 36 3/4" (93.4) TOP VIEW ** llow 4" (10.2) min clearance to a wall for 90 door swing **These units are equipped with a 3-position door stop. The factory set 130 door swing can be adjusted to 90 or 130 for standard installation if clearance to adjacent cabinets or walls is restricted. llow 15" minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimension may vary due to manufacturing tolerances.
STNR INSTLLTION 2 5/16" (5.9) *83 1/2" min *84 1/2" max (212.1-214.6) *Trim will overlap additional 7/16" ELE. 9" (22.9) NTI-TIP RKET 35 1/2" (90.2) 5 1/2" (14.0) FRONT VIEW 81 1/2" (207.0) SIE VIEW INSTLLE WITH NTI-TIP RKET 75 1/2" (191.8) From floor to bottom of electrical area Use two additional hole locations at end of brackets 3 1/8" L racket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs Wall Studs 25 3/8" (64.5) (7.9) 7/16" (1.1) Trim overlap 1 1/2" (3.8) SIE VIEW FRONT VIEW OF UTOUT WITH NTI-TIP RKET STNR INSTLLTION Mounting the junction box in this location will also allow for front accessibility through access panel. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 81 1/2" from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5" of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions.
STNR 1/4" FRME PNEL IMENSIONS SINGLE INSTLLTION Grille Trim STNR INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Supplied Handles 1/4" Framed s: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: panel 67 lbs. Grille panel 11 lbs 1/4" Framed 33 7/8" 8 7/8" 69 5/16" STNR 3/4" OVERLY PNEL IMENSIONS SINGLE INSTLLTION Grille Trim 1/4" acker.10" Spacer 3/4" Overlay Supplied Handles 1/4" acker 33 7/8" 8 7/8" 69 5/16".10" Spacer 32 1/2" 7 5/8" 67 15/16" 3/4" Overlay 34 1/8" 9" 69 9/16" 3/4" Overlay s: For 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. enter each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOTE: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: panel 67 lbs. Grille panel 11 lbs Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle- 30 1/2" long. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle - 64 1/4" long.
USTOM SIE PNELS F 1 7/8" (4.8) 24" (61.0) 3/16" (.5) *84 *84" (213.4) *epending on installation height STNR INSTLLTION F Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the freezer with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. *3" - 4" (7.6-10.2) *epending on installation height 2 9/16" (6.5)
UL INSTLLTIONS 4 5/16" (11.0) 71 1/2" (181.7) Finished Width 24 3/16" (61.4) ELE. 5 1/2" ELE. 5 1/2" 9" (22.9) (13.9) 9" (22.9) (13.9) 26 3/16" (66.5) Min. utout epth STNR INSTLLTION separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product. dditional cutout width may be required when side panels are used. 85" (215.9) Finished Opening 75 1/2" (191.8 ) From floor to bottom of electrical area FRONT VIEW SIE VIEW STNR 1/4" FRME PNEL IMENSIONS UL INSTLLTION Grille PNEL IMENSIONS 1/4" Framed 69 7/8" 8 7/8" 69 5/16" 33 7/8" Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed s: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: panel 67 lbs. Grille panel 25 lbs Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. PNEL SSEMLY ROSS SETION Trim 1/4" Framed Supplied Handles
STNR 3/4" OVERLY PNEL IMENSIONS UL INSTLLTION UL PROUT LERNES 25" (63.5) min To wall PNEL SSEMLY ROSS SETION 130 swing Grille 1" (2.5) 130 swing Trim 1/4" acker.10" Spacer 25" (63.5) min To wall 5" (12.7) min PNEL IMENSIONS 1/4" acker 2" min (5.1).10" Spacer 3/4" Overlay 69 7/8" 68 1/2" 70 1/8" 8 7/8" 7 5/8" 9" 69 5/16" 67 15/16" 69 9/16" 33 7/8" 32 1/2" 34 1/8".25" +.10" +.75" = 1.10" Total Thickness 3/4" Overlay Supplied Handles 15" (38.1) min To wall STNR INSTLLTION 3/4" Overlay s: For 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. enter each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOTE: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: panel 67 lbs. Grille panel 25 lbs Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle - 30 1/2" long. ZKHSS2: European stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle - 64 1/4" long. In a side-by-side installation of a leftand-right-hand door swing product, 1" clearance between the units is required. Order ZUG2: ustom panel unified grille kit for one continuous grille panel. In a side-by-side installation with same door swing, allow 2" minimum clearance between the products to prevent the door swing interference. llow 15" minimum to a wall to achieve full drawer extension and pan removal. dditional clearances are required when using custom panels and handles. NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation. In a side-by-side installation with right and left door hinges together, allow 5 minimum clearance between the two products to prevent one door from striking the other. dditional clearances required when using custom panels and handles. NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel kits will not fit this installation.
OVERLL IMENSIONS INSTLLTION 38" (96.5) 26 1/8" (66.3) 20 5/8" (52.4) 10 15/16" (27.8) *84 11/16" (215.1) *73 3/4" (187.3) * 84" (213.4) 69 3/4" (177.2) SPEIFITIONS Overall Width Overall Height Overall epth learance utout Width utout Height utout epth Plumbing Requirements Shipping Weight 38" (96.5 cm) 84 11/16" (215.1 cm) 26 1/8" (66.3 cm) 38 3/4" (98.4 cm) 39" (99.1 cm) 85" (215.9 cm) 26 3/16" (66.5 cm) 1/4" O copper tubing or GE Smartonnect kit 570 lb (258.5 kg) *4" FRONT VIEW (10.2) SIE VIEW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84 35" (89.0) ase width llow 15" (38.1) min clearance for 115 door swing imensions include 3/4" custom cabinet panel TTENTION ELETRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. 38 3/4" (98.4) TOP VIEW llow 4" (10.2) min clearance to a wall for 90 door swing imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.
INSTLLTION 3/4" PNELS 85" (215.9) 26 3/16" (66.5) Flush inset depth 20 15/16" (53.2) epth to cleat Finished cleats SIE VIEW NTI-TIP RKET 82" (208.3) 5 1/4" (13.3) 3/4" (1.9) Width of side cleats 85" (215.9) Use two additional hole locations at end of brackets 3/4" TOP VIEW Finished cleats ase Trim ase 39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats ELE. 9" (22.9) 5 1/2" (14.0) 24 3/16" (61.4) FRONT VIEW L racket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs Wall Studs 1/2" (1.3) 75 1/2" (191.8 ) From floor to bottom of electrical area INSTLLTION Mounting the junction box in this location will also allow for front accessibility through access panel. Top cleat should be 1" thick WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 82" from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5" of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions. SIE VIEW INSTLLE WITH NTI-TIP RKET FRONT VIEW OF UTOUT WITH NTI-TIP RKET
3/4" PNEL IMENSIONS SINGLE INSTLLTION 1-7/16" Grille ETIL TOP ROUTER EPTH 1/4" 38" 10 7/16" 69 3/4" 3/4" GRILLE OOR PNEL ROUTING PNEL IMENSIONS NOTE: Routed areas should be finished as they may be visible when assembled. ack ack TOP INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door and grille trims. Maximum total panel weight: panel 67 lbs. Grille panel 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide. Handles: ustom handles are required for flush installation. ZKHPSS1: Professional stainless steel handle designed to fit 3/4" custom panels. Kit includes one handle 30 1/2" long. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 64 1/4" long. Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ORNER VIEW SHOWING PITURE FRME ROUTING 1/8" ETIL LEFT SIE ETIL OTTOM ETIL RIGHT SIE OTTOM 3/4" PNEL SIE VIEW (FTER ROUTING) ROUTER EPTH 1/4" ROUTER EPTH 1/4" 3/32" 1/4" 2-1/16" 2-1/16" LEFT SIE RIGHT SIE ack 3/4" PNEL OTTOM VIEW (FTER ROUTING)
3/4" RISE OOR PNEL ROUTING INSTLLTION 11/32" 1/4" 3/16" ETIL TOP 3/4" 1/4" 7/16" NOTE: Routed areas should be finished as they may be visible when assembled. ack ORNER VIEW SHOWING PITURE FRME ROUTING ack TOP Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door and grille trims. Maximum total panel weight: panel 67 lbs. Grille panel 11 lbs ETIL LEFT SIE LEFT SIE ETIL OTTOM ROUTER EPTH 1/4" ROUTER EPTH 1/4" 2-1/16" 2-1/16" ack ETIL RIGHT SIE 3/32" 1/4" RIGHT SIE OTTOM 3/4" PNEL SIE VIEW (FTER ROUTING) Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide. Handles: ustom handles are required for flush installation. ZKHPSS1: Professional stainless steel handle designed to fit 3/4" custom panels. Kit includes one handle 30 1/2" long. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 64 1/4" long. Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. 3/4" PNEL OTTOM VIEW (FTER ROUTING)
INSTLLTION 1/2" PNELS 85" (215.9) 26 3/16" (66.5) Flush inset depth 20 13/16" (52.9) epth to cleat Finished cleats SIE VIEW NTI-TIP RKET 82" (208.3) 5 3/8" (13.7) 3/4" (1.9) Width of side cleats 85" (215.9) Use two additional hole locations at end of brackets 1/2" TOP VIEW Finished cleats ase Trim ase 39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats ELE. 9" (22.9) 5 1/2" (14.0) 24 3/16" (61.4) FRONT VIEW L racket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs Wall Studs 1/2" (1.3) 75 1/2" (191.8 ) From floor to bottom of electrical area INSTLLTION Mounting the junction box in this location will also allow for front accessibility through access panel. Top cleat should be 1" thick WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: wall bracket, bolts and toggles will be supplied with the unit. The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. In installation opening, measure 82" from floor and draw a horizontal line. Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32.5" of installation opening to ensure 2 wall studs are penetrated. The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied L bolts. See Installation Instructions for detailed instructions. SIE VIEW INSTLLE WITH NTI-TIP RKET FRONT VIEW OF UTOUT WITH NTI-TIP RKET
1/2" PNEL IMENSIONS SINGLE INSTLLTION Grille PNEL IMENSIONS 1/4" acker 33 7/8" 8 7/8" 69 5/16".10" Space 32 1/2" 7 5/8" 67 15/16" 1/2" Overlay 38" 10 7/16" 69 3/4" 1/2" OUTER PNEL TO KER PLEMENT INSTLLTION The 1/2" overlay panel must be secured to a.10" spacer panel and a 1/4" thick backer panel, which slides into the trim. ssemble the panels with glue and screws: enter the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight 25 lbs. Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide. Hinge Side 1/2" Overlay ack acker with Overlay ssembly 1/4" acker.10" Spacer Grille ack PNEL IMENSIONS 2 1/16" 2 1/16" 3/16" 1/4" Grille 2 1/16" 2 1/16" 1 7/16" 1/8"
UL INSTLLTIONS 85" (215.9) Finished Opening 4 5/16" (10.9) 75 1/2" (191.8 ) From floor to bottom of electrical area 75" (190.5) Finished Width 24 3/16" (61.4) ELE. 5 1/2" ELE. 5 1/2" 9" (22.9) (13.9) FRONT VIEW 9" (22.9) (13.9) 75 1/2" (191.8 ) From floor to bottom of electrical area 1/2" PNEL IMENSIONS UL INSTLLTION Grille PNEL IMENSIONS 1/4" acker 69 7/8" 8 7/8" 69 5/16" 33 7/8".10" Space 68 1/2" 7 5/8" 67 15/16" 32 1/2" 1/2" Overlay 74" 10 7/16" 69 3/4" 36 7/8" 26 3/16" (66.5) Min. utout epth SIE VIEW INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door, drawer and grille trims. Separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product. Maximum total panel weight: Fresh food door panels 67 lbs. Grille panel 25 lbs Handles ustom handles are required for flush installation. ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle 30 1/2" long. Order 2 kits from your Monogram supplier. ZKHSS2: ustom European handle designed to fit custom panels. Kit includes 2 handles. handle is 44 3/16" and drawer handle is 33 3/16". Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ZKHT: Handle side trim for lefthand and right-hand door. For use on a custom panel when using a custom handle. Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight 25 lbs. The 1/2" overlay panel must be secured to a.10" spacer panel and a 1/4" thick backer panel, which slides into the trim. ssemble the panels with glue and screws: enter the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. Refer to the single unit flush installation diagram on pg 7 for backer to 1/2" overlay panel placement.
3/4" PNEL IMENSIONS UL INSTLLTION Grille PNEL IMENSIONS 3/4" RISE OOR PNEL ROUTING - (SEE PGE 4 FOR 3/4" GRILLE PNEL ROUTING IGRMS) 11/32" 1/4" 3/16" ETIL TOP 3/4" 1/4" 7/16" NOTE: Routed areas should be finished as they may be visible when assembled. ack 74" 10 7/16" 69 3/4" 36 7/8" ack TOP INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door, drawer and grille trims. Maximum total panel weight: Fresh food door panels 67 lbs. Grille panel 22 lbs Handles: ustom handles are required for flush installation. ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle 30 1/2" long. Order 2 kits from your Monogram supplier. ZKHSS2: ustom European handle designed to fit custom panels. Kit includes 2 handles. handle is 44 3/16" and drawer handle is 33 3/16". Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ZKHT: Handle side trim for lefthand and right-hand door. For use on a custom panel when using a custom handle. Order ZUG2: ustom panel unified grille kit for one continuous grille panel. ETIL OTTOM ORNER VIEW SHOWING PITURE FRME ROUTING ETIL HINGE SIE ROUTER EPTH 1/4" ETIL HNLE SIE 2 1/16" 3/16" HINGE SIE ack HNLE SIE 3/4" PNEL OTTOM VIEW (FTER ROUTING) OTTOM 3/4" PNEL SIE VIEW (FTER ROUTING)
UL PROUT LERNES 15" (38.1) min To wall 1" (2.5) 15" (38.1) min To wall INSTLLTION In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. 115 swing 115 swing
FETURES N ENEFITS USTOM PPERNE - llows personalization with cabinet-compatible panels an custom handles UPFRONT ELETRONI ONTROLS WITH IGITL REOUT - llows precise temperature settings and are positioned for maximum ease of use HUMIITY ONTROLLE VEGETLE OMPRTMENTS N SELE SNK PNS - Help maintain freshness and help preserve foods longer JUSTLE, SPILL PROOF GLSS SHELVES - Make it easy to customize storage to handle foods and containers of various sizes 2 SELE ELI PNS WITH FULL - Extension Slides SIX JUSTLE OOR INS - Offer added storage flexibility GE WTER FILTRTION SYSTEM - elivers clean, great tasting ice R