7-786395 mme.modares.ac..ir - * - - mj_mahmoudi@sbu.ac.ir676579 * /.-...... 3. 3. 395 3 : 395 : 395 : - Numerical analysis of free corner effects in angle-ply composite laminates based on global-local method Hossein Mohammadi Roknabadi, Mohammad Javad Mahmoodi * Faculty of Mechanical and Energy Engineering, Shahid Beheshti University, Tehran, Iran. * P.O.B. 676579 Tehran, mj_mahmoudi@sbu.ac..ir ARTICLE INFORMATION Original Research Paper Received 3 May 6 Accepted 6 July 6 Available Online 3 August 6 Keywords: Free corner effect Angle-ply laminates Global-local model Interlaminar stresses ABSTRACT The main purpose of this paper is modeling of the free corner effect of cross-ply and angle-ply graphite/epoxy composite laminates using finite element method based on global-local method. The global area is modeled by first order shear deformation theory and the local area, in the free cornerr vicinity, is modeledd by the Reddy's layer-wise theory. Using this method provides the possibility of analysis of thick angle-ply and cross-pland extension loading, respectively and the effects of the free edgee and free cornerr interlaminar stressess are investigated. Verification of the presented results is performed via available results in the previous studies whichh show good agreement. The present study resultss show that when the cross-ply laminate is subjected to thermal loading, the interlaminar stresses distribution is uniform in both length and width of the laminate. However, for the uni-axial extension loading, the interlaminarr stresses possess different distribution in the two directions of the laminate. Also, results demonstratee thatt in angle-ply laminates under extension loading, the free corner effect increases by increasing fiber angle and the maximum interlaminar stresses occur in 3 degree plies in the freee corner vicinity. Moreover, results prove that the effects of the free edge and the free corner are almost similar in layers with fiber angle lesss than 3 degrees. Parametric study on the thickness and stacking of the laminate layers illustrates that both parameters have a significant influence on the interlamianar stresses at the freee laminates. The cross-ply and angle-ply laminates are subjected to uniform thermal corner.. - Pleasecitethisarticleusing: : H.MohammadiRoknabadi,M.J.MahmoodiNumericalanalysisoffreecornereffectsinangle-plycompositelaminatesbasedonglobal-localmethodModaresMechanical EngineeringVol.6No.8,pp.7-76(iPersian)
- 9 [9]. -.. [-].[5].[6] - [7] [9] [8] -..[-]. -.. ().....[,3]. [3] -. Local-global theory delamination. [].[5-].[9-6]. [].[]..[]....[3] - [,3] 999.. 3 [5] [] 3. [6] 7 6 5. 8 6 [7] 5. [8] 9. Free corner Free edge 3 Single layer higher-order theory Transfer matrix 5 Isotropic 6 Anisotropic 7 Orthogonal 8 Isotropic orthogonal 9 Boundary finite element 86395 8
..[6-5] - = -.[6-5] (5) () - - 3- - -.[6,5] -..[5,-7].. [5] (6). (,, ) = (,, ) + (,, ) x i=3 Multiple models Step by step = = = ( + ) = = + + (5) (6) - - -.[5]() (,,, ) = (,, ) + (,, ) (,,, ) = (,, ) + (,, ) (,,, ) = (,, ) w v u. y x y x z yx () - () = + = + = = + + = + + (,, ) + (,, ) + + = + () :[5] (3) - () () = () = () () () () (3) (3) (i,j= 6 5 ). xy y x. - -.[6] () (,,, ) = (,, ) () (,,, ) = (,, ) () (,,, ) = (,, ) ().[5] yx wvu I () Nz.[5] z. 9 86395
-..[5] (9) [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ { } ] { } [ ] [ ] [ ] [ ] [ ] { } [ ] [ ] [ ] [ ] [ ] { } [ ] [ ] [ ] [ ] [ ] { } { } { } { } { } = { } { } { } { } { } (9) (,, ) () (, ) (,, () (, ) (,, ) () (, ) :[5] () q p () () () (). I j W I V I U I (x,y) (x,y). = q=p. () [ ] [ ] [ ] { } { } { } [ ] [ ] [ ] { } = { } { } [ ] [ ] [ ] { } { () } { } () (9).[5] () - [ ] [ ] [ ] [ ] = } { { } [K LL ] (8) [K EE ] () (3) [K LE ] [K LE ] () :[5] u i ESL u i LWT. z y (). () (FSDT) (7) (LWT) = =, = =, = (7) (7) - - - y x w v u. (,, ) () (, ) (,, () (, ) (,, () (, ) (,, () (, ) (,, ) () (,. FSDT.[5] (8) w j S j S j u j v j e. j (x,y) N N- Rotation U N = U N (8) [ ] =, [ ] = [ ] (3) :[5] () 3 Translation U U 3 = + + + = + U = Fig. Superposition of a FSDT and LWT elements displacement fields LWT FSDT 86395
= z, = - 3 -.. xy.3 mm. 3.. )..... 6. - Fig. Geometry of the laminate; the coordinate origin coincides with point A A substrate dz. [6,5,] - - (5) + + + + + =, = + + + + + + (5) + + + + + + + + + + + + ()) 86395
- [5]. [9].. [3] [3]. (FEM) Hex 7. () 9 6.[3] -. 8 6. 9 x x= 3.993 mm zz 9 8. ( zz - x) 6 y xz yz y= x=3.77 mm.. yz = xz =8.83 MPa y yz=.67 MPa y=3.993mm yz. yz =.67 MPa x=3.993 mm xz xz yz zz (MPa).5.5 - Tahani-Nosier [5] present n=7 present n=5 present n=3 -..5.5 3 zz Fig. 5 Interlaminar normal stresss zz versus y coordinate in the freee edge at the interface of /9.under extension loading. /9 zz 5 closed-form higher-order displacement model 3 MSC/NASTRAN delamination 6.5 y (mm ) () 7 zz =3.75MPa 3 3.5 y Fig. 3 The modified meshing of the solution domain 3 Fig. The modified layout of the layers in the thickness direction [5[ 5] ] [3] [9]. R [9/] s CFRP. T= C.[9 93] ] (6) = 35GPa, = = GPa = = 5GPa, = 3.97GPa = = =.7, =.6 C, = = C (6)) x. y 9 5 7 535. [7]. 5 5 n=7 5. 9 6. [3]. 86395
xz (MPa) - - -6-8 - Zhen-wanji [9] - Becker-Mielstedt [5] - Becker [3] -6 present -8 FEM (MSC/NASTRAN) [3] -.6.8 3. 3. 3. 3.6 3.8 x (mm) Fig. 8 Interlaminar shear stress xz in the vicinity of free corner in the cross-ply laminate at the 9/ interface under thermal loading 8 yz (MPa) 8 6 8 6 Zhen-wanji [9] Becker-Mielstedt [5] Becker [3] present FEM (MSC/NASTRAN) [3] x 9/.6.8 3. 3. 3. 3.6 3.8 y (mm) Fig. 9 Interlaminar shear stress yz in the vicinity of free corner in the cross-ply laminate at the 9/ interface under thermal loading 9 z y 9/ a Fig. Geometry of the angle-ply composite laminate b x y -. [/-] s. x = -6 /.[7,8] (7) = 37.9GPa, = =.8GPa = = = 5.86GPa = = =. (7). -. y x zz x. -. zz (MPa) 35 3 5 5 5-5 Zhen-wanji [9] Becker-Mielstedt [5] Becker [3] present FEM (MSC/NASTRAN) [3] -.6.8 3. 3. 3. 3.6 3.8 x (mm) Fig. 6 Interlaminar normal stress zz in the vicinity of free corner in the cross-ply laminate at the 9/ interface under thermal loading. 6.x 9/ = y/b=. zz =.8 MPa 5. zz =6.33 MPa 6 5 = xz xz =.3 MPa 3 xz =.7 MPa yz. xz =. MPa 6 3 yz =.3 MPa 5 y/a= yz =.9 MPa 6 yz =.5 MPa -. 3 3 yz 3. 3 xz zz (MPa) 5-5 - -5 - -5-3 -35 Zhen-wanji [9] Becker-Mittelstedt [5] Becker [3] present FEM (MSC/NASTRAN) [3] -.6.8 3. 3. 3. 3.6 3.8 y (mm) Fig. 7 Interlaminar normal stress zz in the vicinity of free corner in the cross-ply laminate at the 9/ interface under thermal loading. 7 y 9/ 3 86395
- yz (MPa) 5 5 [5/-5]s [3/-3]s [5/-5]s [6/-6]s. 3-5.65.7.75.8 y/b.85.9.95 Fig. Interlaminar shear stress yz versus non dimentional coordinate in the angle-ply laminate at the /- interface under extension loading. y/b /- 5/- [5/-5] s. h=.,.3,,,.5 mm (7). = -6. 5 x 8-5. zz. 6.5 MPa h=.mm =..73 MPa h=.5 mm y zz 6.5 MPa y/a= h=.mm..73 MPa h=.5 mm. 8 5 h=.mm = xz. MPa h=.5 mm.87 MPa.33 h=.mm y/a= yz. h=.5 mm MPa 8-5. zz (MPa) 7 6 5 3 - [5/-5]s [3/-3]s [5/-5]s [6/-6]s -.65.7.75.8.85.9.95 Fig. Interlaminar normal stress zz versus non dimentional coordinate in the angle-ply laminate at the /- interface under extension loading. zz (MPa) 7 6 5 3 -. /- [5/-5]s [3/-3]s [5/-5]s [6/-6]s -.65.7.75.8.85.9.95 Fig. Transverse normal stress zz versus y/b non dimentional at the angle-ply laminate at /- interface under extension loading. xz (MPa) 3 - - -3 - y/b y/b /- [5/-5]s [3/-3]s [5/-5]s [6/-6]s -5.65.7.75.8.85.9.95 Fig.3 Interlaminar shear stress xz versus non dimentional coordinate in the angle-ply laminate at the /- interface under extension loading. /- 3 86395
yz (MPa).7.6..3...75.8.85.9.95 y/b h= & h=.5 h=.3 h= h=. Fig. 8 Interlaminar shear stress yz versus y/b non-dimentional coordinate for different laminate thickness in the angle-ply laminate at the 5/-5 interface under extension loading 5/-5 8 y./b - zz (MPa) 8 6 - h=. h= & h=.5 h=.3 h= -.75.8.85.9.95 Fig. 5 Interlaminar normal stress zz versus non-dimentional coordinate for different laminate thickness in the angle-ply laminate at the 5/-5 interface under extension loading 5/-5 5 x./a = zz.78 MPa [5/-5] s zz..3 MPa [-5/5] s.78 MPa [5/-5] s y/b=..3 MPa [-5/5] s 9 8 [-5/5] s [5/-5] s xz.3 MPa = y/b= yz.3 MPa -9. - 5 -.... zz (MPa) 8 6 - - h=. h=.3 h= & h = & h=.5-6.75.8.85.9.95 y/b Fig. 6 Interlaminar normal stress zz versus y/b non-dimentional coordinate for different laminate thickness in the angle-ply laminate at at 5/-5 interface under extension loading 5/-5 6 xz (MPa).5 - - -.5 - y./b h=.3 h= h=& h =.5 h=. -.5.75.8.85.9.95 Fig. 7 Interlaminar shear stress xz versus non-dimentional coordinate for different laminate thickness in the angle-ply under extension loading laminate at the 5/-5 interface 5/-5 7 x./a [-5/5] s [5/-5] s. (7) -9 5. 5/-5 5 86395
- yz (MPa).5 - - -.5 [5/-5]s [-5/5]s -.75.8.85.9.95 y/b Fig. Interlaminar shear stress yz versus y/b non-dimentional coordinate for [5/-5] s and and [-5/5] s laminates under extension loading at the 5/-5 interface 5/-5 y/b [-5/5] s [5/-5] s zz (MPa) - - -.5 [5/-5]s [-5/5]s -.75.8.85.9.95 Fig. 9 Interlaminar normal stress zz versus non-dimentional coordinate for [5/-5] s and [-5/5] s laminates under extension loading at the 5/-5 interface 5/-5 9. [-5/5] s [5/-5] s. 3... - 6 [] B. Pipes, N. J. Pagano, Interlaminar stresses in composite laminates under uniform axial extension, Composite Materials, Vol., No., pp. 58-5, 97. [] Ch. Mittelstedt, W. Becker, Interlaminar stress concentration in layered structures: Part I-A selective literature survey on the free-edge effect since 967, Composite Materials, Vol. 38, No., pp. 37-6,. [3] W. Becker, P. P. Jin, P. Neuser, Interlaminar stresses at the free corners of a laminate, Composite Materials, Vol. 5, No., pp. 55-6,999. [] Ch. Mittelstedt, W. Becker, Free-corner effects in cross-ply laminates: An approximate higher-order theory solution, Composite Materials, Vol. 37, No., pp. 3-68, 3. [5] Ch. Mittelstedt, W. Becker, A single-layer theory approach to stress concentration phenomena in layered plates, Composites Science and Technology, Vol. 6, No. -, pp 737-78,. [6] A. Barroso, V. Manti, F. París, Singularity analysis of anisotropic multimaterial corners, Fracture, Vol. 9, No., pp. -3, 3. [7] Ch. Mittelstedt, W. Becker, Asymptotic analysis of stress singularities in composite laminates by the boundary finite element method, Composite Structures, Vol. 7, No., pp. -9, 5. [8] Ch. Mittelstedt, W. Becker, Efficient computation of order and mode of three-dimensional stress singularities in linear elasticity by the boundary finite element method, Solids and Structures, Vol. 3, No., pp. 868-93, 6. [9] W. Zhen, Ch. Wanji, A higher-order displacement model for stress concentration problems in general lamination configurations, Material & Design, Vol. 3, No. 5, pp. 58-67, 9. [] W. Becker, P. P. Jin, J. Lindemann. The free corner effect in thermally loaded laminates, Composite Structures, Vol. 5, No., pp. 97-,. [] H. Yazdani Sarvestani, A. Naghashpour, M. Heidari-Rarani, Bending analysis of a general cross-ply laminated using 3D elasticity solution and layerwise theory, Advanced Structural Engineering, Vol. 7, No., pp. 39-3, 5. [] J. Q. Ye, H. Y. Sheng, Free-edge effect in cross-ply laminated hollow cylinders subjected to axisymmetric transverse loads, Mechanical Sciences, Vol. 5, No. 8, pp. 39-36, 3. [3] J. S. Ahn, Y. W Kim, Analysis of circular free edge effect in composite laminates by -convergent global local model, Mechanical Sciences, Vol. 66, No., PP. 9-55, 3. [] M. Mirzababaee, M. Tahani, Accurate determination of coupling effects on free edge interlaminar stresses in piezoelectric laminated plates, Composite Materials, Vol. 3, No. 8, pp. 963-97, 9. zz (MPa) - - -.5 [5/-5]s [-5/5]s -.75.8.85.9.95 y/b Fig. Interlaminar normal stress zz versus y/b non-dimentional coordinate for [5/-5] s and and [-5/5] s laminates under extension loading at the 5/-5 interface 5/-5 xz (MPa)..3.. -. -. -.3 -. y/b [-5/5] s [5/-5] s [5/-5]s [-5/5]s -.75.8.85.9.95 Fig. Interlaminar shear stress xz versus non-dimentional coordinate for [5/-5] s and and [-5/5] s laminates under extension loading at the 5/-5 interface. 5/-5. [-5/5] s [5/-5] s. 6..8 MPa 5 MPa 6.33. 86395 6
higher-order theory for the free edge effect in laminates, Composite Structures, Vol. 8, No., pp. 99-5, 7. [] W. Zhen, C. H. Roggeng, Ch. Wanji, Refined laminated composite plate element based on global local higher-order shear deformation theory, Composite Structures, Vol. 7, No., pp. 35-5, 5. [3] W. Ding, Delamination Analysis of Composite Laminates, PhD Thesis, University of Toronto, Toronto, 999. [] C. T. Sun, S. G. Zhou, Failure of quasi-isotropic composite laminates with free edges, Reinforced Plastics and Composites,Vol. 7, No. 6, pp. 55-557, 988. [5] J. N. Reddy, Mechanics of Laminated Composite Plates and Shells: theory and analysis, Second Edittion, pp..75-.769, CRC Press LCC, Boca Raton, Florida, 95. [6] E. J. Barbero, J. N. Reddy, Modeling of delamination in composite laminate using a laye-rwise plate theory, Solids and Structures, Vol. 8, No. 3, pp. 373 389, 99. [7] M. Tahani, A. Nosier, Free edge stress analysis of general cross-ply composite laminates under extension and thermal loading, Composite Structures, Vol. 6, No., pp. 9-3, 3. [8] A. S. D. Wang, F. W Crossman, Some new result on edge effect in symmetric composite laminates, Composite Materials, Vol., No., pp. 9-6, 977. - [5] Ch. Zhang, A. Binienda, A meso-scale finite element model for simulating free-edge effect in carbon/epoxy textile composite, Mechanics of Materials, Vol. 76, No., pp. -9,. [6] T. T. H. Le, C. M. Wang, T. Y. Wu, Exact vibration results for stepped circular plates with free edge, Mechanical Sciences, Vol. 7, No. 8, pp. 8, 5. [7] M. Shariyat, Nonlinear thermomechanical dynamic buckling analysis of imperfec viscoelastic composite/sandwich shells by a double-superposition global local theory and various constitutive models, Composite Structures, Vol. 93, No., pp. 833-83,. [8] M. Shariyat, S. H. Hosseini, Eccentric impact analysis of pre-stressed composite sandwich plates with viscoelastic cores: a novel global local theory and a refined contact law, Composite Structures, Vol. 7, No., pp. 333 35,. [9] Ch. Wanji, S. I. Junling, A model of composite laminated beam based on the global-local theory and new modified couple-stress theory, Composite Structures, Vol. 3, No., pp. 99-7, 3. [] S. M. R. Khalili, M. Shariyat, A finite element based global-local theory for static analysis of rectangular sandwich and laminated composite plates, Composite Structures, Vol. 7, No., pp. 77-89,. [] S. H. Lo, W. Zhen, Y. K Cheung, Ch. Wanji, An enhanced global local 7 86395