sles@jumo.co.uk info.us@jumo.net Pge /5 JUMO AQUIS touch S Modulr Multichnnel Mesuring Device for Liquid Anlysis with Integrted Controller nd Pperless Recorder Brief description Mesuring The JUMO AQUIS touch S is the obvious choice s centrl pltform for displying nd processing phvlue, redox voltge, electrolytic conductivity, ultrpure wter resistnce, temperture, disinfection mesurnds, (e.g. free chlorine, totl chlorine, chlorine dioxide, ozone, hydrogen peroxide nd percetic cids nd lso flow rte). Pulse rte inputs (counters) re vilble for flow mesurements. Universl inputs cn be used to mesure nlog mesurnds vi stndrd signls [0() to 0 ma or 0 to 0 V]. In totl, the device cn mesure nd mnge up to 9 prmeters simultneously. Control Besides numerous simple lrm, limit vlue or timecontrolled switching functions, up to four higherorder control loops cn be defined in the JUMO AQUIS touch S t the sme time. Tried nd tested JUMO control lgorithms re used for P, PI, PD, nd PID control in these pplictions. Disply A 5.5" TFT color screen with touch function serves to disply ll prmeters s well s operte nd setup the device. The plin text opertion philosophy virtully elimintes the need for mnul. The operting lnguge cn be selected from mong 5 lnguges tht re lredy included in the device t the fctory. The lnguge librry cn be expnded to up to 0 lnguges vi the PC setup progrm. It is lso possible to disply lnguges with Chinese or Cyrillic chrcters. As result, the device is predestined for globl use. Record A pperless recorder is integrted for dt recording. Up to 8 nlog mesurnds nd 6 binry signls re recorded nd displyed on the screen in their chronologicl sequence. Storge is tmperproof nd enbles officil recording obligtions to be fulfilled. The dt cn be red vi JUMOPCC softwre or USB flsh drive nd evluted using the PC evlution softwre JUMO PCA000. Typicl pplictions The modulr setup nd open structure of the device permits host of potentil pplictions: Communl nd industril wter tretment in wstewter tretment plnts Process systems Drinking nd bthing wter monitoring Phrmceuticl wter Food nd beverge production (CIP/SIP plnts) Gs scrubbers / ir wshers Cooling tower control Ion exchngers ROunits (reverse osmosis) Power sttions nd energy plnts Fish breeding Deslintion of sewter JUMO AQUIS touch S Type 058/... Specil fetures Up to nlysis inputs in ny combintion for direct connection of sensors for liquid nlysis Up to 5 further mesuring signls cn be connected either directly or vi interfce pulse frequency inputs for flow mesurement (mx. 00 Hz or 0 khz) Up to 7 switching outputs tht re configurble s controller, switching, nd lrm outputs Interfces: USB host, USB device, Modbus, PROFIBUSDP, nd Ethernet Ethernet function: web server, lrm lerts vi emil, setup vi PC, extrction of recorded mesurement dt Mth nd logic functions Integrted timers, wsh timers, nd clibrtion timers Service nd operting hours counters Processdt recording with tmperproof storge Luminous TFT color grphics screen with 5.5 screen digonl, 0 0 pixel, QVGA, nd 56 colors Intuitive opertion vi touchscreen Configurble user rights Freely configurble opertor displys PC setup progrm Conductivity mesurement for nturl wters nd TDSmesurement Switchble conductivity mesuring rnges for CIP/SIPplnts in the beverge industry Complince with phrmceuticl industry requirements to USP <65> Wll csing (protection type IP67) with mple connection spce
sles@jumo.co.uk info.us@jumo.net Pge /5 Block digrm Voltge supply ccording to order detils AC 0 to 0 V, 8 to 6 Hz or AC/DC 0 to 0 V, 8 to 6 Hz Switching signls for e.g. mnul mode, timer strt/stop, etc. IN nd IN dditionlly: Pulse frequency signls for encoders e.g. impeller sensors for flow mesurement PWR IN IN binry input IN binry input IN binry input PWR OUT DC ±5 V DC V / V OUT binry output OUT binry output Prllel tp from PWR IN, e.g. for supplying pumps Voltge supply outputs: DC ±5 V for ISFETpHsensors nd DC V or DC V (see order detils) for trnsmitters, sensors, etc. Rely switching outputs with normlly open contct Pt00, Pt000, RTD temperture probe with customerspecific chrcteristic line, IN 5 dditionlly: resistnce trnsmitter nd NTC Input for stndrd signl (Current signl) 0() to 0 ma IN temperture input IN 5 temperture input IN 6 universl input OUT binry output OUT nlog output OUT 5 nlog output Rely switching output with chngeover contct Stndrd signls 0 to 0 V or 0() to 0 ma Updte with USB flsh drive firmwre, extrct mesurementdt memory, sve service dt, sve/lod configurtion USB host interfce COM RS/85 USB device interfce Seril interfce for Modbus For setup progrm nd mesurement dt, extrct with JUMO PCC/PCA000 COM COM Option plugin bords: RS/85 or PROFIBUSDP LAN Ethernet For web server, emil, setup progrm, Modbus TCP/IP, nd JUMO PCC/PCA000 Option plugin bord Universl inputs: 0() to 0 ma, 0 to 0V, Pt00, Pt000, RTD temperture probe with customerspecific chrcteristic line, resistnce trnsmitter Option plugin bords wy binry input: ech for up to switching signls IN nlog input IN nlog input IN //5 binry inputs IN 6/7/8 binry inputs IN OUT 6/7 IN OUT 8/9 IN //5 OUT 0/ IN 6/7/8 OUT / OUT /5 OUT 6/7 OUT 6/7 nlog/binry output OUT 8/9 nlog/binry output OUT 0/ nlog/binry output OUT / nlog/binry output OUT /5 nlog/binry output OUT 6/7 nlog/binry output Optionl bords Anlog outputs: Stndrd signls 0 to 0 V/ 0() to 0 ma Optionl bords for binry outputs: wy rely chngeover contct/ wy rely normlly open contct/ wy solid stte rely Tric (SSR)/ wy solid stte rely PhotoMOS / wy logic output 0/ V/ wy logic output 0/ V Only OUT /5 optionl bord for voltgesupply outputs: OUT 8/9 OUT 8/9 nlog/binry output DC ±5 V for ISFETpHsensors DC V for trnsmitters, sensors, etc. Optionl bords for nlysis inputs (in ny combintion): IN 7 nlysis input IN 7 phvlue/redox potentil/nh for phsensors (conventionl nd ISFET), redox, or NHsensors/ electrolytic conductivity (conductive) for conductivity sensors in /conductor technology/ electrolytic conductivity (inductive) for inductive conductivity sensors from JUMO IN 8 nlysis input IN 9 nlysis input IN 0 nlysis input IN 8 IN 9 IN 0 Power supply unit nd Bse unit with stndrd connections Option plugin slots for expnsion with optionl bords
sles@jumo.co.uk info.us@jumo.net Pge /5 Device setup () () (5) () () () TFTtouchscreen (5) Optionl slots () Cse (terminl comprtment cover opened) (6) USB interfces () Terminl blocks, power supply unit (7) USB host socket IP67 (optionl) () Terminl blocks, Bse unit (8) Cble entries (6) (7) (8) Disply nd control elements () Touchscreen () Toolbr with buttons for opertion () ()(5) (6) (7) (8) () () () Device settings menu button with: Disply of dte, time Loggedin user (in the exmple: Mster) Remining memory disply in percent for recording function (in the exmple: 00 %) () Alrm/event list button (5) Select opertor disply button (6) Home button (bck to min view) (7) Plceholder for contextsensitive buttons (ssignment bsed on opertor disply concerned) (8) Next opertor disply button
sles@jumo.co.uk info.us@jumo.net Pge /5 Description Operting concept The JUMO AQUIS touch S is operted vi the touchdisply. Mesured vlues, operting sttes, nd digrms of the individul functions re displyed nd visulized on up to 6 opertor displys. The device functions cn be controlled using the buttons on the corresponding opertor displys. Touching the nvigtion buttons selects the opertor disply to be shown. The opertor displys re rrnged in n operting loop nd cn be run in loop vi the Next opertor disply button nd selected using the Select opertor disply button. The Device settings menu button is for configurtion nd prmeteriztion. A further menu for viewing pending lrms nd n event protocol cn be opened vi the Alrm/ event list button. Operting level Select opertor disply Device settings menu Login/logoff Nvigtion in the operting loop Next opertor disply Alrm/ event list Alrm list Mster: Complete device configurtion permitted Service: Access for uthorized service personnel User/User: Restricted user rights The scope of the user rights, s well s psswords nd user nmes cn be edited vi the PC setup progrm. Operting loop/opertor displys The operting loop comprises overview screens nd 6 individul screens s stndrd. Further opertor displys re creted by configuring controllers nd recording groups, thereby provisioning controller screens nd digrms in the operting loop. The individul opertor displys cn be configured for showing selected mesured vlues or binry signls nd for defining hedings. Overview screens The overview screens re pooled displys of mesured vlues nd binry signl sttes. For the nlog mesurnds, prt screens, or prt screens cn be configured for displying or disply fields, ech with min nd secondry mesured vlue. One dditionl vlue nd up to binry vlues cn lso be displyed in ech overview screen. Hedings of the disply window nd the disply fields cn be renmed. Input signls cn be freely ssigned to the disply fields. One prt overview screen displys up to 9 nlog nd binry signls. Dt monitor This function is included in the stndrd version. The dt monitor displys mesurement dt s line recorder digrm with time stmp. There re groups vilble. For ech ctivted group, digrm is displyed in the operting loop s long s the group concerned is configured. nlog chnnels nd binry chnnels cn be displyed per group. The mesurement dt re stored in ring buffer. The oldest mesurement dt re overwritten to llow mesurement dt recording to continue when the ring buffer is full. Recording function This function equtes to conventionl pperless recorder nd is vilble s n extr code. It corresponds essentilly to n expnded dt monitor function with the following dditionl options: Disply mesurement dt history (scroll digrm) Dt retrievl vi USB flsh drive or JUMO PCC softwre The mesurement dt histories cn be retrieved vi JUMO PCC softwre or lterntively vi USB flsh drive, nd cn be displyed, evluted, nd rchived using the JUMO PCA000 PC Evlution Softwre. Clibrtion Event list User level Configurtion Prmeteriztion Function level Device info Service Clibrte touchscreen User rights The vilble operting nd setting options depend on the user rights of the loggedin user. The device holds user ccounts. Individul screens The individul screens re lrgescle displys of min mesured vlue with secondry mesured vlue. One dditionl vlue nd binry signls cn lso be displyed. The min vlue is visulized by br grph. Limit vlues for lrm functions of the mesuring input concerned re displyed by mrks on the br grph.
sles@jumo.co.uk info.us@jumo.net Pge 5/5 Process screen The PC setup progrm is ble to crete customerspecific process screen in which globl overview of the plnt process cn be displyed. Once creted, the process screen is trnsferred by the PC setup progrm to the JUMO AQUIS touch S, where it becomes prt of the operting loop. Up to 50 objects (screens, digitil displys, br grphs, texts, etc.) cn be used in the process screen. Typicl for process screen: User level A user level is menu which the user cn ccess quickly nd simply in order to define certin prmeters nd configurtion settings. A userdefined block of up to 5 settings cn be selected vi the PC setup progrm nd stored t user level. Function level The Function level menu llows internl functions to be used nd the sttus of these functions to be displyed. For exmple, counters cn be reset or wsh opertion strted mnully here. PC setup progrm The PC setup progrm enbles the JUMO AQUIS touch S to be conveniently configured nd prmeterized using PC. Dt records cn be creted, edited, trnsmitted to the device nd extrcted in this wy. The dt cn be sved nd printed. Anlysis inputs Four optionl slots for nlysis inputs cn be flexibly equipped with optionl bords for mesuring phvlue, redox potentil, NH, nd electrolytic conductivity (conductive/inductive). The conductivity mesurement lso covers TDS nd ultrpure wter pplictions within its performnce rnge of services. A compenstion for numerous influencing vribles (e.g. temperture nd phvlue) cn be configured. This mkes the JUMO AQUIS touch S the centrl mesuring point for ll nlysis mesurnds in one process. The diverse rnge of connectble electrodes nd sensors enble ll processrelevnt mesurnds to be recorded in single device. In ddition to nlysis mesurnds, these mesurnds include physicl mesurnds, such s temperture nd flow rte, nd lso ny mesurnd cpble of being trnsferred s pulse frequency signl or stndrd signl. Alrm functions ensure the monitoring of mesured vlues for overrun nd underrun of limit vlues. The limit vlues cn be defined by the user. Anlog inputs Besides the stndrd temperture mesuring inputs (Pt00, Pt000, resistnce trnsmitters, NTC, etc.) nd the universl input (0() to 0 ma) of the Bse unit, dditionl nlog inputs with optionl bords cn be mde vilble. The optionl nlog inputs cn be configured for RTD temperture probes, resistnce trnsmitters, nd voltge nd current signls. This mkes the JUMO AQUIS touch S extremely flexible to use for mesuring numerous mesurnds. Here too, the user cn configure lrm functions for monitoring mesured vlues for overrun nd underrun. Customerspecific lineriztion In ddition to the stndrdized, fctorystored sensor chrcteristic lines, customerspecific lineriztion is lso possible. This option llows ny sensor chrcteristic lines to be entered. Progrmming is done vi the PC setup progrm through vlue tble (up to 0 vlue pirs) or by inputting th degree polynomil. Binry inputs The signls from stndrd nd up to 6 optionl binry inputs (potentilfree contcts nd logic signls) cn be used to trigger vrious internl functions, switchover of prmeter block or the strt of utotuning, for exmple. IN nd IN enble the frequency of encoders to be mesured in order to perform flow mesurements using impeller sensors or monitor the rottionl speed of pumps, for instnce. There re mesuring rnges vilble, depending on how the mesuring principle in the flow function is configured: to 00 Hz (periodic time mesurement) 00 Hz to 0 khz (pulse counting) Externl inputs Bus technologies enble further 8 nlog nd 8 binry inputs to be employed for signl trnsmission with bus users. Anlog outputs The nlog outputs re freely sclble (current, voltge). They cn be used to output controller outputs, setpoint vlues, mth results, nd the nlog input signls (e.g. ctul vlue). Besides the stndrd nlog outputs of the Bse unit, up to 7 more with optionl bords cn be retrofited. Binry outputs Binry outputs re switching nd logic outputs. Binry outputs enble the output of lrms, limit vlue contcts, logic results nd controller signls. Three binry outputs (OUT to rely) re provided s stndrd. A mximum of 7 binry outputs cn be chieved in the device by mens of optionl bords. The following vrints re vilble s optionl bords: wy output rely (chngeover contct) wy output rely (normlly open contct) wy output solid stte rely Tric wy output solid stte rely PhotoMOS (werfree control, e.g. of metering pumps)
sles@jumo.co.uk info.us@jumo.net Pge 6/5 Limit vlue monitoring In ddition to the lrm functions of the mesuring inputs, there re 8 limit vlue monitors, ech with selectble switching functions (min. lrm, mx. lrm, lrm window, inverted lrm window) vilble. The limit vlue cn be permnently configured. This function enbles the monitoring of ny nlog vlues. The violtion of limit vlue cn trigger lrms, event list entries, or switching functions. The digrms below show the limit vlue functions concerned. Min. lrm Binry vlue Hysteresis Pulse length output Output level Y 00 % 90 % 50 % 0 % 0% Pulse frequency output Output level Y 00 % 50 % 0% Proportionl bnd 0 Proportionl bnd 0 % 90 % Switching period 50 % 50 % 0 % 90 % Actul vlue Mximum pulse frequency 50 % of pulse frequency No pulse Actul vlue between its two prmeter blocks in order to dpt the controller behvior if certin process conditions chnge. Prmeter blocks cn be toggled seprtely for ech controller chnnel. Autotuning The utotuning function lso enbles user who is not control technology expert to dpt the controller to the control pth. During this process, the rection of the control pth to the chnges in the ctuting vrible is evluted. The step response method is implemented in the controller chnnels of the JUMO AQUIS touch S to llow utotuning. 0 Limit vlue Mx. lrm Binry vlue 0 Alrm window Binry vlue Hysteresis Input signl Hysteresis Limit vlue Input signl Hysteresis Controller individul screens The controller functions re visulized in detil here. Dt such s ctul vlue, setpoint vlue, nd output level re displyed. The controller cn be used in this view (mnul output rtio, setpoint vlue input). Mth nd logic function The mth nd logic module enbles nlog chnnels to be ssocited with one nother, nd lso nlog chnnels to be ssocited with counters nd binry inputs. Numerous opertors re vilble for the formule. The JUMO PC setup progrm cn be used to crete formule with bsic rithmetic opertions, root functions, power functions, logrithm functions, ngle functions, nd mny other functions. Opertors AND, OR, NOT, XOR, nd edge detections re vilble for logic printouts. The mth nd logic module cn be configured solely vi the PC setup progrm. This function is vilble s n option. 0 Controller Limit vlue Window rnge Inverted lrm window Binry vlue 0 Hysteresis Limit vlue Window rnge Hysteresis Input signl Input signl Up to PID controllers cn be ctivted t the sme time. Ech nlog input signl (nlysis size, temperture, stndrd signl, etc.) cn be freely ssigned to one of the controller chnnels. Feedforwrd control, prmeter block switchover, nd corse/fine control function enble especilly stble controller behvior. The controller outputs cn be configured s continuous output (output level s stndrd signl), pulse length output (output level s pulse length), or pulse frequency output (output level s pulse frequency). Controller overview screen If t lest controller chnnels re configured, n overview of ll controllers with the most importnt dt is displyed in the operting loop. Controller prmeters Two prmeter blocks cn be sved for ech of the controller chnnels. Ech prmeter block hs 5 prmeters for dpting the controller to the conditions of the process concerned. Ech controller cn be toggled Flow rte Two flow mesurement functions cn be configured. Flow rtes cn be mesured on the bsis of the pulse signls t IN or IN nd/ or of n nlog input signl. The mesured flow rte cn be integrted vi the Totl quntity function. In this wy, the liquid volume tht hs pssed over the mesuring point is cumulted over configurble period. Counter Four counters cn be used to count ctivtion opertions or operting hours of binry functions such s lrms, binry inputs, wsh timers, etc. This function is intended primrily for monitoring mintennce intervls.
sles@jumo.co.uk info.us@jumo.net Pge 7/5 Timers Two timer functions re included. They cn be configured either s timers or time switches. Configured s timer, the functions ct like time rely. The timer is controlled for strting, resetting nd stopping vi binry signls. A timer cn lso be stopped, or its strt delyed, by the tolernce bnd function. The tolernce bnd is the devition of mesured vlue from predefined reference. If the configured devition is exceeded, the timer concerned stops. The chronologicl sequence of the timer signl cn be influenced by the settings timer time, timer strt runup time, nd timer end time in such mnner tht typicl time rely functions (e.g. response dely or fllbck dely) cn be chieved. The time switch function corresponds to week timer. Up to ctivtion nd dectivtion times cn be set for ech weekdy. Wsh timer Two wsh timers re used for the regulr clening of electrodes. Certin recurring functions re triggered t preconfigurble intervls. Wsh timers cn, for exmple, control binry outputs in order to ctivte clening process in the plnt. By clening sensors on regulr bsis, optiml mesuring certinty cn be gurnteed. Clibrtion timer The clibrtion timer function reminds the opertor to reclibrte the sensors. Corresponding lrms nd event list entries cn be individully configured. Clibrtion logbook Anlog inputs IN 6 to IN re covered by clibrtion logbook, in which ll successfully completed clibrtion processes re recorded long with the dte, time, nd numerous other detils. An overview of the clibrtion history on the nlysis sensors is therefore vilble t ll times. USB interfces There re two types of USB interfce host interfce nd device interfce. A USB flsh drive cn be connected to the host interfce. Mesurement dt, configurtion dt, nd service dt cn thus be sved. Additionlly, configurtions cn be uploded from the flsh drive to the device nd device softwre updtes cn be run. The device interfce serves, in combintion with stndrd USB cble, to operte the PC setup progrm nd to retrieve mesurement dt for the optionl recording function vi the JUMO PCC softwre. Both USB interfces re locted next to the connection terminls in the bse bord. The host interfce cn optionlly be ttched to USB host socket (see order detils) on the cse next to the cble entries, llowing it to be used without opening the cse. Seril interfces RS/85 The JUMO AQUIS touch S hs stndrd RS/85 interfce with Modbus RTU protocol (slve). A further interfce cn be retrofitted s n optionl bord. Seril interfces re used to integrte the device into n utomtion network. This llows the JUMO AQUIS touch S to communicte with SCADA system or other Modbus mster devices. PROFIBUSDP interfce The PROFIBUSDP interfce cn be used to integrte the JUMO AQUIS touch S into fieldbus system operting ccording to the PROFIBUSDP stndrd. An pplictionspecific GSD file, vi which the JUMO AQUIS touch S is integrted into the fieldbus system, is generted by mens of the project engineering tool supplied (GSD genertor; GSD = bsic device dt (Gerätestmmdten)). Ethernet interfce The JUMO AQUIS touch S cn be integrted into LAN vi the optionl Ethernet interfce. This enbles the device to communicte with ll PCs in the LAN concerned. The PC setup progrm nd PCC communiction softwre cn be ccessed from these PCs using the JUMO progrms. The Ethernet interfce permits use of the web server, emil, nd Modbus TCP/IP functions. Web server (online visuliztion) HTML documents, which cn be creted using conventionl HTML editor, cn be stored in the JUMO AQUIS touch S using the PC setup progrm. These documents cn contin texts, grphics, nd JvScript code. Anlog nd binry vlues of the JUMO AQUIS touch S cn be displyed vi JvScript. The result is website which cn be retrieved over the Internet or LAN nd displyed vi PC using conventionl web browser. On this website, the user cn now see cler disply of the plnt or the process, including mesured vlues nd operting sttes. A Stndrd online visuliztion function is stored t the fctory. A PC with Microsoft Windows operting system nd Silverlight instlled is required to use this function. Web server JUMO AQUIS touch S HTTP Web browser HTTP Web browser Alrm/event list The lrm list reports currently pending errors. Possible lrm messges include clibrtion lrms or lrms triggered by input signls. Once the error sources re eliminted, lrms dispper utomticlly. The event list stores nd reports events, such s the ppernce nd disppernce of lrms, voltge supply filures, clibrtions, etc. However, event list entries cn lso be configured in the functions of the JUMO AQUIS touch S. Emil/SMS text messge Internet/ LAN The JUMO AQUIS touch S cn be configured for the eventcontrolled disptch of emil messges. This enbles mintennce personnel to be notified bout the presence of lrms, for exmple (lso vi trnsmission s SMS in the emil/sms gtewy of cellulr phone provider).
sles@jumo.co.uk info.us@jumo.net Pge 8/5 Technicl dt Anlog inputs, Bse unit Temperture mesuring input (IN ) Probe/signl type Connection type Mesuring rnge Mesuring ccurcy Ambient temperture influence Pt00 DIN EN 6075 wire/wire 00 to +850 C 0.05 % of MR 50 ppm/k Pt000 DIN EN 6075 wire/wire 00 to +850 C 0. % of MR 50 ppm/k RTD temperture probe with customerspecific chrcteristic line b Up to 00 Ω wire/wire 0 to 00 Ω c 0.5 % of R mx 00 ppm/k Up to 000 Ω wire/wire 0 to 000 Ω c 0.5 % of R mx 00 ppm/k Sensor led resistnce Mximum 0 Ω per line with wire circuit. Led compenstion Not required for wire circuit. With wire circuit, led clibrtion cn be executed t the respective input by mens of n ctul correction vlue using the Offset setting. MR: mesuring rnge scope.. b Customerspecific lineriztion cn be used to enter sensor chrcteristic line. c R mx : mximum resistnce cross the mesuring rnge (00 Ω or 000 Ω) Temperture mesuring input (IN 5) Probe/signl type Connection type Mesuring rnge Mesuring ccurcy Ambient temperture influence Pt00 DIN EN 6075 wire/wire 00 to +850 C 0.05 % of MR 50 ppm/k Pt000 DIN EN 6075 wire/wire 00 to +850 C 0. % of MR 50 ppm/k Resistnce trnsmitter wire 0 to 00 kω b 0.5 % of R Tot 00 ppm/k RTD temperture probe with customerspecific chrcteristic line c Up to 00 Ω wire/wire 0 to 00 Ω Up to 000 Ω wire/wire 0 to 000 Ω d 0.5 % of R mx 00 ppm/k Up to 00 kω wire/wire 0 to 00 kω NTC 8k55 wire/wire 0 to 50 C NTC k wire/wire 0 to50 C d 0. % of R mx 00 ppm/k Sensor led resistnce Mximum 0 Ω per line with wire circuit. Led compenstion Not required for wire circuit. With wire circuit, led clibrtion cn be executed t the respective input by mens of n ctul correction vlue using the Offset setting. MR: mesuring rnge scope. b R Tot : totl resistnce of the resistnce trnsmitter. c Customerspecific lineriztion cn be used to enter sensor chrcteristic line. d R mx : mximum resistnce cross the mesuring rnge (00 Ω, 000 Ω or 00 kω). Universl input (IN 6) Signl type Mesuring rnge Mesuring ccurcy Ambient temperture influence Current signl 0() to 0 ma 0. % of MR 00 ppm/k MR: mesuring rnge scope.
sles@jumo.co.uk info.us@jumo.net Pge 9/5 Anlog inputs, optionl bords Universl input (IN, IN ) Probe/signl type Connection type Mesuring rnge Mesuring ccurcy Ambient temperture influence Pt00 DIN EN 6075 wire/wire 00 to +850 C 0.05 % of MR 50 ppm/k Pt000 DIN EN 6075 wire/wire 00 to +850 C 0. % of MR 50 ppm/k Resistnce trnsmitter wire 00 to 000 Ω b 0.5 % of R Tot 00 ppm/k RTD temperture probe with customerspecific chrcteristic line c Up to 00 Ω wire/wire 0 to 00 Ω d 0.5 % of R mx 00 ppm/k Up to 000 Ω wire/wire 0 to 000 Ω d 0.5 % of R mx 00 ppm/k Voltge signl 0 to 0 V 0. % of MB 00 ppm/k Current signl 0() to 0 ma 0. % of MB 00 ppm/k Sensor led resistnce e Mximum 0 Ω per line with wire circuit. Led clibrtion e Not required for wire circuit. With wire circuit, led clibrtion cn be executed t the respective input by mens of n ctul correction vlue using the Offset setting. MR: mesuring rnge scope.. b R Tot : totl resistnce of the resistnce trnsmitter. c Customerspecific lineriztion cn be used to enter sensor chrcteristic line. d R mx : mximum resistnce cross the mesuring rnge (00 Ω or 000 Ω) e Specifiction does not pply for stndrd signls. Anlysis input: ph/redox/nh Mesurnd Mesuring rnge Temperture compenstion Mesuring ccurcy phwert (stndrd electrode) to 6 ph 0 to +50 C 0. % of MR phwert (ISFET electrode) to 6 ph None Redox voltge 500 to +500 mv None NH (mmoni) 0 to 0000 ppm 0 to +50 C MR: mesuring rnge scope.. Ambient temperture influence 0.%/0K Anlysis input: CR (conductivity, conductive) Units Disply rnges Temperture compenstion µs/cm ms/cm kω cm MΩ cm 0.00 to 9.9999 00.00 to 99.999 000.00 to 999.99 0000.0 to 9999.9 00000 to 99999 TC liner, nturl wter DIN EN 7888, nturl wter with expnded rnge, TDS c, ASTM D595 for neutrl (NCl), cid (HCl) nd lkli (NOH) impurities Cell constnt wire: 0.0 to 0 cm wire: 0.5 to cm Mesuring rnge chngeover b Four mesuring rnges Configurble Mesuring ccurcy 0.6 % of MR d + 0. µs cell constnts (C) Ambient temperture influence 0.%/0K The disply rnge is sclble. The deciml plce is freely configurble. An utomtic deciml plce cn lso be set. b Up to different mesuring rnges with seprte disply rnge limits, units, temperture compenstion processes nd lrm functions cn be configured. The respective ctive mesuring rnge is selected vi binry signls. c TDS (Totl Dissolved Solids) d MR: mesuring rnge scope.
sles@jumo.co.uk info.us@jumo.net Pge 0/5 Anlysis input: Ci (conductivity, inductive) Units Mesuring/disply Temperture compenstion rnges µs/cm ms/cm 0.00 to 9.9999 00.00 to 99.999 000.00 to 999.99 0000.0 to 9999.9 00000 to 99999 The disply rnge is sclble. The deciml plce is freely configurble. An utomtic deciml plce cn lso be set. b Up to different mesuring rnges with seprte disply rnge limits, units, temperture compenstion processes, nd lrm functions cn be configured. The respective currently ctive mesuring rnge is selected vi binry signls. c TC: temperture coefficient. d MRE: mesuring rnge end vlue. Temperture compenstions Compenstion type Compenstion rnge Linerer TC 50 to +50 C TC curve 50 to +50 C TDS 50 to +50 C Nturl wter ccording to DIN EN 7888 0 to 6 C Nturl wter with expnded temperture rnge b 0 to 00 C ASTM D595 (neutrl, lkli nd cid impurities) 0 to 00 C NOH 0to% 0to90 C NOH 5 to 50 % 0 to 90 C HNO 0to5% 0to80 C HNO 6 to 8 % 0 to +65 C H SO 0to8% 7to+0 C H SO 6 to 85 % 7 to +5 C H SO 9 to 99 % 7 to +5 C HCL0to8% 0to65 C HCLto % 0to+65 C Mesuring circuit monitoring, Bse unit TC liner, c TC curve, nturl wter, nturl wter with expnded temperture rnge, NOH0to%, NOH 5 to 50 %, HNO 0to5%, HNO 6 to 8 %, H SO 0to8%, H SO 6 to 85 %, H SO 9 to 99 %, HCl 0 to 8 %, HCl to % Cell constnt Mesuring rnge chngeover b.00 to 8.00 cm Four mesuring rnges Configurble Mesuring ccurcy For 0 to 999 µs/cm:.5 % of MRE d For to 500 ms/cm: % of MRE d For 500. to 000 ms/cm.5 % of MRE d Ambient temperture influence 0. %/K TC: temperture coefficient. b The temperture compenstion "nturl wter with expnded temperture rnge" extends beyond the stndrdized temperture thresholds of DIN EN 7888. Inputs Underrnge/overrnge Short circuit/ Open circuit sensor brek Temperture input Yes Yes Yes Universl input (current signl) Yes Yes Yes With current nd voltge signls, error detection depends on the input configurtion.
sles@jumo.co.uk info.us@jumo.net Pge /5 Mesuring circuit monitoring, optionl bords Input/sensor Underrnge/overrnge Short circuit/ sensor brek phvlue (glss electrode) Yes Configurble Impednce mesurement Anlog outputs, Bse unit nd optionl bords Binry inputs, Bse unit Open circuit Configurble Impednce mesurement Specil fetures phvlue (ISFET) Yes No Underrnge/overrnge Conductivity, conductive Yes Underrnge/overrnge Configurble Detection of deposits (wire circuit) Conductivity, inductive Yes No Yes Universl input for connection of: voltge/current signl, RTD temperture probe Yes Yes b Yes b Universl input for connection of: resistnce trnsmitter b No Yes Yes The stndrd underrnge/overrnge monitoring function is lwys ctive. Monitoring vi impednce mesurement cn be optionlly ctivted. Since this depends on mrginl prmeters, the following points must be observed: Impednce mesurements re possible only with glssbsed sensors. Sensors must be connected directly to n nlysis input for ph/redox/nh on the device. Impednce converters must not be instlled in the mesuring circuit. The mximum dmissible cble length between sensor nd trnsmitter is 0 m. Fluid resistnces hve direct impct on the mesurement result. It is therefore dvisble to ctivte the impednce mesurement in liquids from minimum conductivity of pprox. 00 µs/cm. With current nd voltge signls, error detection depends on the signl scling. 0 V or 0 ma my be interpreted s sensor errors. Signl type Signl rnge Admissible lod resistnce Accurcy Ambient temperture influence Voltge signl 0 to 0 V > 500 Ω 0.5 % 00 ppm / K Current signl 0/to0mA <50Ω 0.5 % 00 ppm / K Description Input frequency rnges Min. pulse durtion Signl type Switching thresholds On Off On Off IN b Hz 00 ms 00 ms Configurble s: >8V <5V IN b,c to 00 Hz 0 μs 0 μs potentilfree contct or >.8mA <.ma IN b,c 00 Hz... 0 khz 0 μs 0 μs externl voltge source This specifiction is relevnt only if the externl voltge source is selected under the Contct item in the configurtion. b All binry inputs IN to re suitble for connecting proximity switches. Recommended types re: Wchendorff PCB08NOA nd Blluff BES MEGPSC80FBP0. c Binry inputs IN nd IN cn be used for impeller flow sensors (wter meters) or mgneticinductive flow meters, for exmple. The input frequency depends on the configured mesurement principle in the flow function. Binry inputs, optionl bords Mx. number of retrofittble binry inputs Mx. optionl bords with binry inputs ech Binry outputs, power supply unit bord Mx. pulse frequency Min. pulse durtion Signl type On Off Hz 00 ms 00 ms Potentilfree contct Description Switching output Ampcity t ohmic lod OUT OUT OUT Rely, normlly open contct Rely, normlly open contct Rely, chngeover contct The mximum mpcity of the contcts must not be exceeded. Contct life A t AC 50 V 50,000 switching opertions
sles@jumo.co.uk info.us@jumo.net Pge /5 Binry outputs, optionl bords Optionl crd Switching output Mx. current Contct life Rely output wy Normlly open contcts Rely output wy Chngeover contct Solid stte rely Tric Solid stte rely PhotoMOS e The mximum mpcity of the contcts must not be exceeded. b Combining mins voltge circuit with protective low voltge circuit on wy normlly open contct option is not dmissible. c Ampcity t ohmic lod. d A vristor protects the Tric ginst excessive voltges, such s cn occur during switching processes. e PhotoMOS is registered trdemrk of Pnsonic. f Current limiting vi the logic output of the device. Voltge supply outputs, Bse unit normlly open contcts b chngeover contct Switching output with Tric (protected by vristor) d Switching output with PhotoMOS e A t AC 50 V c 50,000 switching opertions A t AC 0 V c Werfree Specil fetures 00 ma t DC 50 V or AC 5 V c Werfree Not shortcircuitproof Mx. voltge DC 50 V AC 5 V Werfree Logic output 0/ V High/low signl 0 ma f Logic output 0/ V High/low signl 0 ma e Werfree l Description Output voltge Ampcity Connection DC V/ V voltge supply (e.g. for externl trnsmitters) DC V +5 / 5 % DC V +5 / 5 % 5 ma 0 ma Springcge terminls DC ±5 V voltge supply (e.g. for DC +5 V ±5 % 00 ma ISFET phsensors) DC 5 V ±5 % 0 ma Voltge supply outputs, power supply unit bord Voltge supply outputs, optionl bord l Bsed on order code. Description Output voltge Totl mpcity PWR OUT AC 0 to 0 V +0 / 5 %; 8 to 6 Hz or A AC/DC 0 0 V; 8 6 Hz The sum totl of the output currents for the two PWR OUT connections must not exceed the totl mpcity. Interfces Seril interfce RS/85 (Bse unit nd optionl bord) Protocol Dt formts Modbus (slve) 8 no prity 8 odd prity 8 even prity Connection Springcge terminls Description Output voltge Ampcity Connection DC V voltge supply for externl trnsmitters DC V 0 ma DC ±5 V voltge supply (e.g. for DC +5 V ±5 % (between terminls nd ) 50 ma Screw terminls ISFET phsensors) DC 5 V ±5 % (between terminls 5 nd ) 0 ma An optionl bord for voltge supply outputs ccommodtes ll the outputs listed in this tble. A mximum of such optionl bord cn be integrted into device. Device ddresses Bud rtes in bud Connection to 5 9600 900 800 Springcge terminls Specifiction in useful bit stop bit prity formt. Therefore, the frme lwys comprises 8 useful bits nd stop bit. Only the prity is differentited.
sles@jumo.co.uk info.us@jumo.net Pge /5 PROFIBUSDP (optionl bord) Protocol DPV0 Dt formts Big Endin Little Endin Device ddresses Bud rtes Connection 0 to 7 MBud Dsub socket 9pole 5 9 6 Big Endin corresponds to the Motorol dt formt nd Little Endin to Intel dt formt. Ethernet optionl bord (0/00BseT) Function Use Appliction protocol/ Specil fetures Connection progrm Web server Online visuliztion vi HTTP Editble vi HTML RJ 5 socket web browser Editor Emil / SMS text messge Emil disptch vi SMTP Five emil templtes SMTP server cn be stored, 8 Trnsmission s SMS text up to receivers for messge ech emil templte Modbus TCP/IP Process dt exchnge with Modbus TCP/IP slve TCP Port: 50 Modbus users b Automtic IP configurtion Network dministrtion c DHCP Setup vi PC Device settings vi PC setup progrm JUMO PC setup progrm (HTTP) Recording function d Extrct, rchive, evlute mesurement JUMO PCC nd PCA000 dt The emil function llows the device, triggered by internl nd/or externl binry signls, to send hrdprogrmmed messges. This requires the dt of n SMTP server (emil intermedite server) to be known. The emil function cn be configured exclusively vi the PC setup progrm. b Modbus TCP/IP enbles Modbus users to communicte vi LAN, provided this is connected to the LAN (e.g. vi gtewys). To configure Modbus communiction, you will require the interfce description for the JUMO AQUIS touch S. c Enlist the help of your network dministrtor or n IT specilist for the IP configurtion. d The recording function stores mesurement dt in ring buffer inside the device. Further detils pper on Pge 5. USB interfces, Bse unit Interfce Use Support Connection Version USB host interfce Extrct mesurement dt memory USB flsh drive USB port type A USB.0 Red/write device settings Sve service dt b Updting the firmwre USB device interfce Device setting vi PC setup progrm Extrct, rchive, evlute mesurement dt JUMO PC setup progrm JUMO PCC/PCA000 softwre USB port type Mini B 5 The recording function stores mesurement dt in ring buffer inside the device. Further detils pper on Pge 5. b Service dt cn be stored on USB flsh drive for dignostic purposes.
sles@jumo.co.uk info.us@jumo.net Pge /5 Electricl dt Voltge supply (switch mode PSU) Touchscreen Cse Cse type AC 0 0 V +0 / 5 %; 8 6 Hz or AC/DC 0 0V;8 6Hz Electricl sfety According to EN 600, prt overvoltge ctegory III, pollution degree Mx. power consumption AC 0 0 V 5.7 VA AC/DC 0 0 V 6. VA Dt bckup Flsh memory Electricl connection Springcge terminls nd screw terminls Specifictions for conductor cross sections on Pge 6 Electromgnetic comptibility (EMC): DIN EN 66 Interference emission Clss B Interference immunity Industril requirements Type TFTtouchscreen Touchscreen sensors Resistive (cn lso be operted wering gloves) Disply protection Plstic film for protection ginst dmge nd scrtches Size 5.5" Resolution 0 0 pixel Color depth 56 colors Viewing ngle Horizontl: ±70 Verticl: 70 to +50 Mterils Dimensions Ambient temperture Storge temperture Resistnce to climtic conditions Surfcemounted cse mde of plstic (ABS) Terminl comprtment cover screws:.567 stinless steel Mounting plte:.0 stinless steel 0.5 mm 8. mm 0.5 mm 5 +50 C 0 +70 C Reltive humidity < 9 % nnul verge, no condenstion Operting position Any (with due considertion for the viewing ngle of the screen) Protection clss According to EN 6059 Closed cse IP67 Open cse IP0 Cble entries Scope of delivery Stndrd version Full configurtion kit (see ccessories) Weight without holder for wll mounting (fully configured) Weight of holder for wll mounting Cble fittings: 6 M.5 x M6.5 Cble fittings: 9 M.5 M6.5 M0.5 90 g 790 g
sles@jumo.co.uk info.us@jumo.net Pge 5/5 Functions Controller chnnels Quntity Controller type Twostte controller Threestte controller Continuous controller Corse/fine controller Threestep controller Continuous controller with position controller Controller structure P, PI, PD, PID Controller outputs For ech controller chnnel, outputs configurble s: pulse length output, pulse frequency output, continuous output Disturbnce feedforwrd control Multiplictive nd/or dditive Autotuning Step response method Disturbnce feedforwrd control llows influencing vribles in the process environment going beyond the ctul vlue to be considered. This keeps the controller behvior stble, even when fluctutions in such mbient conditions occur. Recording function Number of groups Number of input vribles per group Customerspecific lineriztion Dt monitor Recording function (optionl) nlog binry nlog binry Recording / memory cycles to 600 sec. to 600 sec. Memory vlues Current vlue Averge vlue Minimum vlue Mximum vlue Current vlue Averge vlue Minimum vlue Mximum vlue Size of the ring buffer b Sufficient for 50 entries c Sufficient for pprox. million entries c History function d No Yes Archiving/evlution No Yes (vi JUMO PCA000 evlution softwre) A freely configurble set of input vribles cn be pooled in one group. Ech group hs its own disply screen. The group ffilition is considered for dt storge, in order to enble evlution vi PC. b The mesurement dt re stored in ring buffer. When the ring buffer is full, the recording function begins t the strt of the ring buffer by overwriting the mesured vlue history. c The specifiction reltes to nlog vlues nd binry vlues per entry nd ids orienttion. The sum totl of both groups is indicted. d The history function llows you to scroll through the digrm to pst recording times. All mesurement dt stored in the ring buffer cn therefore be viewed on the device. Number of support points Interpoltion b Formul entry c Up to 0 vlue pirs Liner th degree polynominl The pproximte chrcteristic line cn be entered by inputting support points (vlue pirs of the customerspecific chrcteristic line). b Liner interpoltion mens the formtion of slope function through support points. c As n lterntive to support point entry, customerspecific chrcteristic line cn lso be entered s formul in the form of polynomil. Approvls / pprovl mrks Approvl mrk Testing gency Certifictes / certifiction numbers Inspection bsis Underwriters Lbortories Registered UL 600 CAN/CSAC. No. 600 Vlid for Type 058/...
sles@jumo.co.uk info.us@jumo.net Pge 6/5 Connection digrm The connection digrm in the dt sheet provides preliminry informtion bout the connection options. For the electricl connection, only the instlltion instructions or the operting mnul should be used. The knowledge nd the correct technicl execution of the sfety informtion/ instructions contined in these documents re mndtory for instlltion, electricl connection, strtup, nd for sfety during opertion. Importnt informtion on conductor crosssections nd ferrules Ferrule Conductor crosssection Minimum length of ferrule or Minimum Mximum stripping Without ferrule Power supply unit 0. mm ² mm 8mm Bse unit 0. mm ² mm 8mm With ferrule without lip Power supply unit 0.5 mm 0.75 mm 8mm Bse unit 0.5 mm 0.75 mm 8mm With ferrule with lip Power supply unit 0.5 mm 0.75 mm 8mm Bse unit 0.5 mm 0.75 mm 8mm Rigid Power supply unit 0. mm ².5 mm 8mm Bse unit 0. mm ².5 mm 8mm Connection overview
sles@jumo.co.uk info.us@jumo.net Pge 7/5 Anlog inputs, Bse unit Connector/terminl Connection vrint Symbol IN RTD temperture probe wire circuit Pt00, Pt000, or customerspecific chrcteristic line 8 0 RTD temperture probe wire circuit Pt00, Pt000, or customerspecific chrcteristic 8 9 0 IN 5 RTD temperture probe wire circuit Pt00, Pt000, or customerspecific chrcteristic line RTD temperture probe wire circuit Pt00, Pt000, or customerspecific chrcteristic NTC wire circuit NTC wire circuit Resistnce trnsmitter A = Strt E=End S = Slider E S A IN 6 Stndrd signl for current 0() to 0 ma + I X 5
sles@jumo.co.uk info.us@jumo.net Pge 8/5 Anlog inputs, optionl bords Universl inputs Expnsion slot Connection vrint Symbol IN IN RTD temperture probe wire circuit Pt00, Pt000, or customerspecific chrcteristic line RTD temperture probe wire circuit Pt00, Pt000, or customerspecific chrcteristic line Resistnce trnsmitter A = Strt E=End S = Slider Stndrd signl Voltge 0 to 0 V Stndrd signl Current 0() to 0 ma + + E S A U X I X
sles@jumo.co.uk info.us@jumo.net Pge 9/5 Anlysis inputs Expnsion slot Option / connection vrint Symbol IN 7 IN 8 IN 9 IN 0 ph/redox Symmetric connection = glss/metl electrode b = reference electrode FP= liquid potentil GND = shielding Terminls nd re not connected! ph/redox Asymmetric connection = glss/metl electrode b = reference electrode GND = shielding Terminls nd re not connected! Conductivity, inductive (Ci) connection vi M connector, connect compenstion thermometer connections (core cble of connection socket) to suitble nlog input (wire circuit) fctory wiring must not be chnged! Conductivity, conductive (CR) electrode system with wire conductor with concentric conductivity sensors, terminl must be connected to the outer electrode. b FP GND b GND 5 6 5 6 6 Temp. mesuri input Conductivity, conductive (CR) electrode system with wire conductor; wiring to minimize the mesuring error cused by ledwire resistnce; With concentric conductivity sensors, terminl must be connected to the outer electrode. Conductivity, conductive (CR) electrode system; : Outer electrode (I hi) : Inner electrode (U hi) : Inner electrode (U lo) : Outer electrode (I lo) 6: Shielding Schirm Schirm Schirm 6 6 6
sles@jumo.co.uk info.us@jumo.net Pge 0/5 Anlog outputs Bse unit Connector/terminl Connection vrint Symbol OUT Anlog output + U DC 0 to 0 V or IX DC 0() to 0 ma X (configurble) OUT 5 Anlog output + DC 0 to 0 V or UX DC 0() to 0 ma IX (configurble) 8 9 0 Optionl bords: Expnsion slot Option / connection vrint Symbol OUT 6/7 OUT 8/9 OUT 0/ OUT / OUT /5 OUT 6/7 OUT 8/9 Anlog output DC 0 to 0 V or DC 0() to 0 ma (configurble) + UX I X
sles@jumo.co.uk info.us@jumo.net Pge /5 Binry inputs Bse unit Connector/terminl Connection vrint Symbol IN Binry input (potentilfree contct) NO Binry input (externl voltge source) + IN Binry input (potentilfree contct) NO 5 Binry input (externl voltge source) + 5 IN Binry input (potentilfree contct) NO 6 7 Binry input (externl voltge source) + 6 7 Optionl bords: Connector/terminl Connection vrint Symbol IN //5 IN 6/7/8 binry input NO NO NO
sles@jumo.co.uk info.us@jumo.net Pge /5 Binry outputs Power supply unit bord Connector/terminl Connection vrint Symbol OUT OUT OUT Rely Normlly open contcts Rely Chngeover contct NO NC Com NO Optionl bords: Expnsion slot Option / connection vrint Symbol OUT 6/7 OUT 8/9 OUT 0/ OUT / OUT /5 OUT 6/7 OUT 8/9 Rely Chngeover contct relys N/O contct Solid stte rely Tric 0 V/ A x solid stte relys PhotoMOS b 50 V/00 ma NO NO NC Com NO Binry output 0/ V +
sles@jumo.co.uk info.us@jumo.net Pge /5 Expnsion slot Option / connection vrint Symbol OUT 6/7 OUT 8/9 OUT 0/ OUT / OUT /5 OUT 6/7 OUT 8/9 Mins power connection binry outputs 0/ V Combining mins voltge circuit with protective low voltge circuit on wy normlly open contct option is not dmissible. b PhotoMOS is registered trdemrk of Pnsonic. + + Connector/terminl Connection vrint Symbol PWR IN Mins power input L N PE L N PE Voltge supply outputs Bse unit Connector/terminl Connection vrint Symbol DC ±5 V Voltge supply for ISFET sensors + U = DC V/ V Voltge supply for externl trnsmitters V / V + 6 U = 7
sles@jumo.co.uk info.us@jumo.net Pge /5 Power supply unit bord Connector/terminl Connection vrint Symbol PWR OUT Supply voltge L led out N PE L N PE Optionl bord Expnsion slot Connection vrint Symbol OUT /5 Voltge supply DC ±5 V for ISFET sensors + U = 5 Voltge supply DC V for externl trnsmitters V (see order detils) + U =
sles@jumo.co.uk info.us@jumo.net Pge 5/5 Interfces Bse unit Connector/terminl Connection vrint Symbol COM RS 5 6 7 RS85 RxD/TxD+ RxD+ RxD TxD+ TxD RxD/TxD 6 7 USB device USB device Type MiniB USB (socket) 5 USB host USB host Type A USB (socket)
sles@jumo.co.uk info.us@jumo.net Pge 6/5 Optionl bords: Expnsion slot Connection vrint Terminting resistors COM LAN RS The terminting resistors with DIP switches on optionl bords Configurble RS85 The terminting resistors with DIP switches on optionl bords Configurble PROFIBUSDP = RxD/TxDP 5 = DGND 6 = VP 8 = RxD/TxDN Ethernet Type RJ 5 (socket) Without terminting resistors Symbol With terminting resistors RxD+ RxD TxD+ TxD RxD/TxD+ RxD/TxD 5 9 6 8
sles@jumo.co.uk info.us@jumo.net Pge 7/5 Glvnic isoltion Option plugin bords Bse unit nd power supply unit bord Option plugin bords: binry outputs: wy rely normlly open contct, wy chngeover contct OUT 6 to OUT 9 Option plugin bords: binry outputs: Solid stte rely Tric (SSR) OUT 6 to OUT 9 Option plugin bords: binry outputs: Solid stte rely PhotoMOS OUT 6 to OUT 9 Option plugin bords binry outputs: logic output 0/ V OUT 6 to OUT 9 Option plugin bords: nlog outputs: 0/ to 0 ma or 0 to 0 V OUT 6 to OUT 9 Option plugin bords binry outputs: wy logic output 0/ V OUT 6 to OUT 9 Option plugin bord for voltge supply outputs DC V nd DC ±5 V: OUT /5 AC.7 kv AC.7 kv AC 50 V AC 50 V AC 50 V AC 50 V AC.7 kv AC 50 V AC 50 V AC 50 V Binry outputs Rely, power supply unit bord OUT to OUT Anlog outputs, bse unit OUT to OUT 5 Binry inputs, bse unit IN to IN Temperture input on bse unit IN Temperture input on bse unit IN 5 Anlog input 0/ to 0 ma bse unit IN 6 Option plugin bords: nlysis inputs: IN 7 to IN 0 Voltge supply output DC ±5 V bse unit Option plugin bords: universl inputs: IN to IN AC 50 V AC 50 V Voltge supply output DC / V bse unit Option plugin bord: wy binry inputs IN to IN 8 AC 50 V AC 50 V USB host interfce, bse unit Option plugin bord: RS85/RS, PROFIBUSDP COM USB device interfce, bse unit AC 50 V Option plugin bord: Ethernet LAN RS85/RS bse unit COM AC 50 V AC 50 V Voltge supply AC or AC/DC Test voltge AC voltge supply:.7 kv, 50 Hz AC/DC voltge supply:.7 kv, 50 Hz Wrning: If sensors without glvnic isoltion re operted t binry input nd cn be powered by n externl voltge source, potentil differences between the internl nd the externl ground cn cuse problems. Drwing the voltge from the voltge supply outputs on the JUMO AQUIS touch S is therefore preferred.
sles@jumo.co.uk info.us@jumo.net Pge 8/5 Dimensions View from below (Cble entries) 7.5 mm 0.5 mm. mm 70.5 mm 8 mm 7.5 mm 8. mm 0 mm 0.5 mm Side view Front view
sles@jumo.co.uk info.us@jumo.net Pge 9/5 Surfce mounting Drilling digrm 6.6 mm 7 mm Ø 5 mm () () () () 99 mm 99 mm 7 mm () JUMO AQUIS touch S () Mounting plte () Selftpping screws 60 6; TORX PLUS 0IP (from the JUMO AQUIS touch S ccessories pouch) () Fstening screws (hexgon screws Ø 6 mm) (5) Wether protection cnopy (prt no. 006050) TORX PLUS is registered trdemrk of Acument Intellectul Properties, LLC. USA. () () () Surfce mounting with wether protection cnopy 99 mm 7 mm () (5) ()
sles@jumo.co.uk info.us@jumo.net Pge 0/5 Pipe mounting ØD () () () () (5) () Pipe/pole (customer provision) clmping rnge of clips = D () Selftpping screws 60 6; TORX PLUS 0IP (from the AQUIS touch S ccessories pouch) () Pipe clips from the pipe mounting kit (prt no. 00600) () Mounting plte for pipe mounting from the pipe mounting kit (prt no. 00600) (5) JUMO AQUIS touch S (6) Wether protection cnopy (prt no. 006050) TORX PLUS is registered trdemrk of Acument Intellectul Properties, LLC. USA. Pipe mounting with wether protection cnopy ØD () () () () (6) (5)