Pull Type Rigid Frame, Lift Rotate INNER HITCH The hitch length can be adjusted in 15" increments to accommodate the tractor tire options (single or dual tires) being used and attachments installed on the planter. The hitch consists of a rear section of 7" square tube and a front section of 6" square tube. To adjust the length, lower the machine to the field position and block the transport wheels. Support the 7" square tube with a minimum 5000 pound rated jack to take the weight off the 6" square tube. Remove the 1 1/4" x 9" hex head cap screw, loosen the two 5/8" hex head cap screws on the front end of the 7" square rear section and reposition the 6" square front section to the desired length. CAUTION: DO NOT set the hitch so short that turning ability is limited when the machine is in road transport position. Reinstall and tighten hardware to specified torque values. ITEM PART No. DESCRIPTION ITEM PART No. DESCRIPTION 1 KA8699 Inner Hitch, 65 1/4" 6 KB0156 Clevis 2 K10169 Hex Head Cap Screw, 1 1/4"-7 x 6" 7 See Outer Hitch K10157 Lock Nut, 1 1/4"-7 8 KA4774 Safety Chain, 3/8" 3 KD16328 Hose Holder K1K411 Safety Chain Repair Kit, Includes Hook, Flat 4 K10217 Washer, 5/8" USS Safety Latch, Spring And Retaining Ring K10230 Lock Washer, 5/8" 9 K11058 Hex Head Cap Screw, 1 1/4"-7 x 3" K10104 Hex Nut, 5/8"-11 K10226 Washer, 1 1/4" SAE 5 KA4994 Jack Assembly Complete KD10646 Special Washer KA4995 Detent Pin Assembly K10157 Lock Nut, 1 1/4"-7 KR0517 Pin 10 KA10709 Inner Hitch, 65 1/4", 7 1/2" Offset KR0516 Crank Assembly 11 K10717 Hex Head Cap Screw, 1 1/4"-7 x 9" KR0515 Bevel Gear K10236 Lock Washer, 1 1/4" K10239 Hex Nut, 1 1/4"-7 Rev 03/08 3. 1
Pull Type Rigid Frame, Lift Rotate OUTER HITCH OUTER HITCH ITEM PART DESCRIPTION Rev 03/08 3. 2
Pull Type Rigid Frame, Lift Rotate 1 K10006 Hex Head Cap Screw, 5/8"-11 x 2 1/4" KD7805 Special Washer, 5/8", Hardened KB0218 Bushing, 21/32" I.D. x 7/8" O.D. x 19/32" Long K10107 Lock Nut, 5/8"-11 2 KA6422 Catch Bar 3 KD5857 Spring 4 K10765 Spring Pin, 1/4" x 1" 5 KA6420 Transport Catch 6 KD4743 U-Bolt, 3" x 3" x 1/2"-13 K10228 Lock Washer, 1/2" K10102 Hex Nut, 1/2"-13 7 See Hydraulic System 8 See Transport Latch Cylinder 9 KA7022 Detent Pin W/Chain 10 K10061 Hex Head Cap Screw, 3/8"-16 x 3 1/2" K10229 Lock Washer, 3/8" K10101 Hex Nut, 3/8"-16 11 KD2971-09 Sleeve, 2" Long KD3180-03 Sleeve, 5/8" I.D. x 7/8" O.D. x 1 15/16" Long (As Required) 12 KD7137 Pin, 3/4" x 3 3/8" K10457 Cotter Pin, 5/32" x 1 1/2" 13 KD0776 Hose Clamp, 3/4" x 2" x 2 1/2" 14 K10027 Hex Head Cap Screw, 3/4"-10 x 2 1/2" KD2169 Special Washer, 25/32" I.D. x 1 1/4" O.D., Hardened K10105 Hex Nut, 3/4"-10 15 See Selector Valve, 16 K10716 Hex Head Cap Screw, 3/4"-10 x 1" K10231 Lock Washer, 3/4" KD2169 Special Washer, 25/32" I.D. x 1 1/4" O.D., Hardened 17 K10005 Hex Head Cap Screw, 5/8"-11 x 1 3/4" KD7805 Special Washer, 5/8", Hardened K10230 Lock Washer, 5/8" K10104 Hex Nut, 5/8"-11 18 K10005 Hex Head Cap Screw, 5/8"-11 x 1 3/4" K10205 Washer, 5/8" SAE K10230 Lock Washer, 5/8" K10104 Hex Nut, 5/8"-11 19 KA6371 Outer Hitch, 125 1/2" 20 K10004 Hex Head Cap Screw, 3/8"-16 x 1 1/4" K10108 Lock Nut, 3/8"-16 21 KD10731 Wire Clamp (If Applicable) 22 K10004 Hex Head Cap Screw, 3/8"-16 x 1 1/4" K10229 Lock Washer, 3/8" K10101 Hex Nut, 3/8"-16 23 K10939 Hex Head Cap Screw, 3/8"-16 x 2 1/4" K10108 Lock Nut, 3/8"-16 24 KD16341 Hose Clamp, 3 3/4" x 6" 25 KA11201 Bulkhead Mount 26 K10228 Lock Washer, 1/2" K10102 Hex Nut, 1/2"-13 27 KA6608 Cable Assembly 28 KD14106 Channel 29 KD9129-01 Hose Protector, 48" 30 KD5875 Hose Clamp, 9/16" x 2 1/2" x 2" 31 KD0740 Hose Clamp, 3/4" x 4" x 3 1/2" 32 KD5892 Hose Clamp, 5/8" x 1 1/2" x 1 1/2" 33 K10108 Lock Nut, 3/8"-16 34 KA6404 Jack Storage Mount 35 KA6623 Transport Post, 6 Row 30" KA6418 Transport Post, 8 Row 30" (Shown) 36 K10111 Lock Nut, 1/2"-13 Rev 03/08 3. 3
Pull Type Rigid Frame, Lift Rotate FRAME ASSEMBLY Pull-Type Rigid Frame with a Rotating main frame for transport with hydraulic operation. ITEM PART No. DESCRIPTION ITEM PART No. DESCRIPTION 1 KA9840 Light Bracket 10 K10022 Hex Head Cap Screw, 1/4"-20 x 1/2" 2 KD1113 U-Bolt, 5" x 7" x 5/8"-11 K10227 Lock Washer, 1/4" K10230 Lock Washer, 5/8" K10103 Hex Nut, 1/4"-20 K10104 Hex Nut, 5/8"-11 11 K10019 Hex Head Cap Screw, 5/16" -18 x 1" 3 KB0309 Light Mount Bracket K10232 Lock Washer, 5/16" 4 K10874 Detent Pin, 1/2" x 3 1/2" Grip K10106 Hex Nut, 5/16"-18 5 K10033 Hex Head Cap Screw, 1/2"-13 x 3 1/2 12 See Electrical Components K10206 Washer, 1/2" SAE 13 K10064 Hex Head Cap Screw, 1/4"-20 x 1" K10111 Lock Nut, 1/2"-13 K10227 Lock Washer, 1/4" 6 See stickers K10103 Hex Nut, 1/4"-20 7 KA6401 Frame, 180", 6 Row 30" K10110 Lock Nut, 1/4"-20, Grade B KA9402 Frame, 188", 6 Row 30" K10312 Carriage Bolt, 5/16"-18 x 3/4" KA6364 Frame, 240", 8 Row 30" 14 K10620 Serrated Flange Nut, 5/16"-18 KA9401 Frame, 248", 8 Row 30" 8 KD6783 Bracket 9 See Row Marker Assembly Rev 03/08 3. 4
Pull Type Rigid Frame, Lift Rotate FRAME ASSEMBLY ITEM PART No. DESCRIPTION ITEM PART No. DESCRIPTION 15 KD15950 Light Mount Extension 31 K10172 Hex Head Cap Screw, 3/8"-16 x 5" 16 KD12724 Bracket K10108 Lock Nut, 3/8"-16 17 K10037 Hex Head Cap Screw, 1/2"-13 x 1 1/4" 32 KD9971 Manifold Block K10228 Lock Washer, 1/2" 33 KR0375 Pin, 1" x 3 1/2" K10102 Hex Nut, 1/2"-13 KR0193 Hair Pin Clip 18 KA5121 Pin, 2 1/8" 34 KB0234 16 Adjustment Plug 19 See Lift Cylinder 35 KB0230 16 Cap 20 See Hydraulic System 36 K10014 Hex Head Cap Screw, 1/2"-13 x 1" 21 KD9093 Poly Wear Pad 37 See Row Marker Sequencing 22 KA6850 Valve Mount 38 K10025 Hex Head Cap Screw, 3/4"-10 x 1 1/2" 23 K10120 Hex Socket Set Screw, 3/8"-16 x 1/2" K10231 Lock Washer, 3/4" 24 K10005 Hex Head Cap Screw, 5/8"-11 x 1 3/4" 39 KD9052 Special Washer, 3/4" I.D. x 2" O.D., Hardened 25 K10638 Hex Head Cap Screw, 1/4"-20 x 2" 40 KD10532 Sleeve K10103 Hex Nut, 1/4"-20 41 KA6497 Cam Follower W/Grease Fitting 26 KD10129 Mounting Bracket K10640 Grease Fitting, 1/4"-28 27 See Stroke Limiter Valve 42 KD13250 SMV Bracket 28 K10048 Hex Head Cap Screw, 3/8"-16 x 2" 43 K11159 T-Bolt Clamp, 3 1/2", Stainless Steel K10101 Hex Nut, 3/8"-16 44 KD16046 Bracket 29 KA7153 Stroke Limiter Arm 30 K10403 Hex Head Cap Screw, 1/4"-20 x 2 1/2" K10227 Lock Washer, 1/4" Rev 03/08 3. 5
FRAME Pull-Type Rigid Frame, Lift & Rotate HYDRAULIC OPERATION This planter is equipped for operation from two dual remote hydraulic outlets (SCV). One set of outlets is used to raise and lower the planter and one set is used to operate the markers and fold functions. A hand operated selector valve on the hitch allows selection of marker or fold functions. RAISED FIELD POSITION Safety Lockup Pin Stroke Limiter Valve DANGER: To avoid serious injury or death, care must be taken when operating row markers around overhead power lines. NOTE: Release hydraulic pressure from the system before moving the selector handle. PLANTER LIFT SYSTEM OPERATION The planter lift system consists of one lift cylinder located at the center of the machine. Mounts for this cylinder are located ahead and behind the center post. For planters with rear mounted row units only, the cylinder may be installed in the rear position. For planters with front mounted options (push row units, fertilizer, etc.), the cylinder must be installed in the front position. NOTE: The planter lift cylinder is equipped with a counter balance valve. Hydraulic pressure is required to lower the planter. Counter Balance Valve There are two raised positions on the planter. The first position is with the safety lockup pin installed above the frame assembly to make contact with the stroke limiter valve. This will allow the row units to raise approximately 14 inches off the ground and the toolbar approximately 40 inches. This position is used in making turns or passing over waterways during field operation. RAISED TRANSPORT POSITION The second raised position is the raised transport position. In this position the planter is allowed to raise high enough to permit the row units to clear the transport wheels as the planter is rotated. To raise the planter to the raised transport position: (1) Remove the safety lockup pin. (2) Raise the planter until the lift cylinder is fully extended. (3) Reinstall the safety lockup pin in the same hole which is now below the frame assembly. (4) Lower planter onto safety lockup pin. DANGER: Never work under the planter while in raised position without installing safety lockup devices. 3. 6 Rev. 03/08
Pull Type, Rigid Frame Lift Rotate AXLE & PIVOT WHEEL ASSEMBLY ITEM PART NoDESCRIPTION 1 Rear Trailer Hitch 2 GA7543 Center Post 3 GA6849 Lockup Pin, 17 1/4" G10671 Spring Pin, 3/16" x 3 1/4" G10606 Spring Pin, 1/4" x 2" 4 GA6529 Rock Guard (Optional) 5 G10037 Hex Head Cap Screw, 1/2"-13 x 1 1/4" G10228 Lock Washer, 1/2" G10102 Hex Nut, 1/2"-13 6 GA6435 Bearing ITEMPART No. DESCRIPTION 7 G10028 Hex Head Cap Screw, 3/4"-10 x 3" 16 GD12543 Scraper GD2169 Spcl Washer, 25/32" I.D. x 1 1/4" O.D. 17 G10636 Carriage Bolt, 1/2"-13 x 1 1/2" G10105 Hex Nut, 3/4"-10 G10216 Washer, 1/2" USS 8 GD9122 Shim,.005" Thick G10228 Lock Washer, 1/2" GD9123 Shim,.007" Thick G10102 Hex Nut, 1/2"-13 GD9124 Shim,.020" Thick 18 G10008 Hex Head Cap Screw, 5/8"-11 x 2" 9 GD3389 Tap Block G10230 Lock Washer, 5/8" GD3398 Shim, 16 Gauge 19 GD9051 Bearing Cap GD7888 Shim, 22 Gauge 20 GD9130 O-Ring 10 G10016 Hex Head Cap Screw, 1/2"-13 x 2" 21 G10026 Hex Head Cap Screw, 3/4"-10 x 2" G10228 Lock Washer, 1/2" G10231 Lock Washer, 3/4" 11 GA6496 Bearing housing w/cups,w/o Grease Fit 22 GA4693 Spindle W/Round External Retaining Ring, 10 1/2" GD9121 Cup GD11490 Round External Retaining Ring G10779 Grease Fitting, 90, 1/4"-28 23 GA0895 Bearing 12 GR0375 Pin, 1" x 3 1/2" 24 GR0270 Lug Bolt, 9/16"-18 GR0193 Hair Pin Clip 25 GA2148 Hub W/Cups, 6 Bolt 13 See Rotation Cylinder GR0434 Cup 14 A7380 Axle W/Stub And Scraper Mounts 26 G11081 Hex Jam Nut, 1 1/2"-12, Grade 2 15 G10027 Hex Head Cap Screw, 3/4"-10 x 2 1/2" 27 GA2142 Rim, 5.50" x 20" G10231 Lock Washer, 3/4" 28 GD13401 Tire, 7.50" x 20", 8 Ply, Tubeless W/O Center Rib G10105 Hex Nut, 3/4"-10 GA7434 Valve Stem A. GA6428 Hub And Spindle Assembly (Items 22, 23, 25 And 26) Rev 03/08 3. 7
Pull-Type Rigid Frame, Lift Rotate CONTACT DRIVE WHEEL The contact drive system is a spring-loaded contact drive tire (4.10 x 6") with No. 40 chain. There is one contact drive wheel on a 4- row planter; two on the 6-row, 8-row, and 12-row; and four contact drive wheels on the 16-row and the 24-row planters. There are 2 down pressure springs on each contact drive wheel. The down pressure is factory preset and should not need further adjustment. The spring tension is set leaving 1 1/2" between the spring plugs and the bolt head. Tire pressure should be checked regularly and maintained as follows, Contact drive: 4.1" x 6" -50 PSI Transport / Ground Drive: 7.5" x 20" -40 PSI. See PREPARING THE PLANTER for information on Lubrication or replacement of the Wheel Bearings. DANGER: Rim and tire servicing can be dangerous. Explosive separation of tire and rim parts can cause serious injury or death. See SAFETY section. ASSEMBLY Rev. 12/06 3. 8
Pull-Type Rigid Frame, Lift Rotate CONTACT DRIVE WHEEL ASSEMBLY ITEM PART No. DESCRIPTION 1 2 KD7426 Driveline Sprocket, 12 Tooth 3 KD1026 Sleeve, 1 3/16" Long 4 KA5157 Idler Arm, L.H. 5 KD5827 Cover 6 KD5857 Spring 7 K10312 Carriage Bolt, 5/16"-18 x 3/4" K10232 Lock Washer, 5/16" K10106 Hex Nut, 5/16"-18 8 K3400-01 Flangette 9 K2100-03 Bearing, 7/8" Hex Bore, Spherical 10 KA8925 Mount 11 K10004 Hex Head Cap Screw, 3/8"-16 x 1 1/4" K10229 Lock Washer, 3/8" K10370 KD5756 Machine Bushing, 3/8", 22 Gauge Special Nut, 3/8"-16 12 KB0218 Bushing, 21/32" I.D. x 7/8" O.D. x 19/32" Long 13 KA7369 Wheel Arm (Non-Stock Item)(Sub G1K253) 14 K10306 Carriage Bolt, 3/8"-16 x 2" K10210 Washer, 3/8" USS K10108 Lock Nut, 3/8"-16 15 K10004 Hex Head Cap Screw, 3/8"-16 x 1 1/4" K10229 Lock Washer, 3/8" K10101 Hex Nut, 3/8"-16 16 K10751 Hex Head Cap Screw, 5/8"-18 x 1 3/4" K10235 KD7805 Machine Bushing, 7/8", 14 Gauge Special Washer, 5/8", Hardened K10412 Lock Nut, 5/8"-18 17 KA2068 Spring W/Plug 18 K10501 Hex Jam Nut, 1/2"-13, Grade 2 19 K3310 Chain, No. 40, 116 Pitch Including Connector Link KR0912 Connector Link, No. 40 20 KA5105 Sprocket, 15 Tooth KA5107 Sprocket, 19 Tooth 21 K10602 Spring Pin, 1/4" x 1 1/2" 22 KD6825 Hex Shaft, 7/8" x 10 3/8" (2 Holes) 23 K10233 Machine Bushing, 1", 10 Gauge 24 KA9846 Flanged Bearing, 7/8" Hex Bore 25 K10890 Hex Head Adjusting Bolt, 1/2"-13 x 4", Grade 2 26 KA5090 Tire And Rim Assembly (Specify Brand*) KD5753 Tire, 4.10" x 6" (Specify Brand*) KD5752 Inner Tube 27 KD2558 Lynch Pin, 1/4" 28 K10303 Carriage Bolt, 5/16"-18 x 1" K10232 Lock Washer, 5/16" K10106 Hex Nut, 5/16"-18 A. K1K253 Contact Wheel Arm Replacement Kit (Items 13, 18, 21, 22, 24, 25, 27 and 28 Rev. 12/06 3. 9
_ Pull Type, Rigid Frame TRANSPORT WHEEL Tire pressure should be checked regularly and mainained as follows, Transport/Ground Drive 7.5" x 20" -40 PSI. For information on bearings, see PREPARING THE PLANTER. Due to the clearance between the wheel assembly and the transport tire, a tire scraper should always be used. The tire scraper will prevent a buildup of dirt and mud between the wheel arm assembly and the tire. Adjust the scraper so it does not contact the tire. Ridge Planting For ridge planting, to raise the bar height 3", mount the 20" tires in the lower rear holes in the ground drive wheel arm and springs in the lower set of mounting holes in the wheel module mount and raise the hitch height to mainain a level position from side to side and front to back. ASSEMBLY ITEM PART No. DESCRIPTION 1 K10009 Hex bolt 5/8-11 x 2 1/2 K10230 Lock washer 5/8 K10104 Hex nut 5/8-11 2 KA5122 Wheel tower clamp 3 K10008 Hex bolt 5/8-11 x 2 KD7805 Special washer K10230 Lock washer 5/8 K10104 Hex nut 5/8-11 4 See Hydraulic cylinders 5 KD5841 Pin 1 1/4" x 5 5/8" KD10460 Cotter pin 1/4 x 2 6 KA7376 Scraper mount 7 KD10010 Scraper 8 K11081 Hex jam nut 1 1/2-12 9 KA0895 Bearing 10 KA2148 Hub with cups pressed in KR0434 Bearing cup 11 KR0270 Lug bolt 9/16-18 12 KA2558 Spindle w/retaining ring KD11490 Retaining ring 13 KD13401 Tire 7.50 x 20, 8 ply 14 KA2142 Rim 5.50 x 20 15 KA7434 Valve stem 16 K10025 Hex bolt 3/4-10 x 1 1/2 K10231 Lock washer 3/4 ITEM PART No. DESCRIPTION K10105 Hex nut 3/4-10 21 K10581 Hex bolt 1/2-13 x 2 1/4 17 K10026 Hex bolt 3/4-10 x 2 K10111 Lock nut 1/2-13 K10231 Lock washer 3/4 22 KA5121 Pin 2 1/8" 18 K10636 Carriage bolt 1/2-13 x 1 1/2 23 KA8839 Arm K10228 Lock washer 1/2 24 KD11695 Pin 1 1/4" x 13 1/4" K10216 Washer 1/2 25 K10610 Spring pin 3/8 x 2 K10102 Hex nut 1/2-13 26 KA9877 Clamp w/grease fittings 19 K10139 Washer 1 1/4 K10640 Grease fitting 1/4-28 20 K10159 Bushing 1 1/4 x 10GA KA2147 Hub and Spindle asm (Items 8-10 and 12) Rev. 12/06 3. 9
_ Pull Type Rigid Frame, Lift and Rotate DRIVELINE ASSEMBLY ITEM PART No. DESCRIPTION 1 KD1256 Spring 2 KD1255 L-Pin 3 KA5165 Sprocket, 30 Tooth 4 K10464 Cotter Pin, 3/16" x 1" 5 KA0378 Block And Hub Assembly 6 K10430 External Retaining Ring, 1 1/4" 7 KD9078 Hex Shaft, 7/8" x 58" (4 Holes), 6 Row 30" KD9077 Hex Shaft, 7/8" x 98" (4 Holes), 8 Row 30" 8 KB0287 Coupler 9 KD0914-165 Hex Shaft, 7/8" x 165" (No Holes), 6 Row 30" KD0914-225 Hex Shaft, 7/8" x 225" (No Holes), 8 Row 30" 10 K10131 Square Head Set Screw, 5/16"-18 x 3/4" 11 K10130 Square Head Machine Bolt, 5/16"-18 x 1 3/4" K10923 Flange Nut, 5/16"-18, No Serration 12 KD11045 Lock Clamp A KA5164 Ratchet/Sprocket Assembly (Items 1-6) B K1K269 Lock Clamp Kit (Items 11 And 12) Rev. 03/08 3. 10