HZ492300TX AG-3-DRAWER STORAGE ORGANIZER Assembly Instructions For assistance with assembly, contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com www.seidal.com 1
A HZ492300TX AG-3-DRAWER STORAGE ORGANIZER Parts List Please review all parts and hardware before disposing of any packaging. Call Customer Service if missing hardware. Using a screw that is too long will cause damage. Before beginning assembly, separate each type of screw. Carefully study the Screw diagrams below. You may receive extra hardware with your unit. B Top panel Side panel-left C D of 2 Side panel-right Shelf panel E F of 2 Bottom panel Top rail G of 2 H of 6 Bottom rail Drawer front I of 3 J of 6 Drawer bottom Drawer side 2
k. of 3 L. Male slide M. of 4 rail 1. of 4 leg 2. 0 Bolt : 1/4 x2 3. of 8 Screw M4*28mm 4. of 40 Flat washer 5. of 40 Cam bolt 6. Cam locks. of 26 Allen wrench 8. of 4 Wood Dowel 8*30mm 9. 10. of 8 of 26 Bolt : 1/4 x1-5/8 spring washer Care and Cleaning Instructions: Before using, wipe with a clean, dry cloth. Periodically apply furniture wax to renew the finish. Avoid rubbing or scratching the surface with rough or abrasive objects. PVC cover For replacement parts or questions, please Call Customer Service at 1-800-633-5096, please call Manufacturer for assistance, questions or Parts. Assembly Tool Required No.2 Phillips Screwdriver (Not Included) 3
( 1) HZ492300TX AG-3-DRAWER STORAGE ORGANIZER ( 2) Assembly Instructions Unpack and lay parts on clean, padded surface like carpet or blanket. Check that you have all parts indicated on the front page "Please do not over tighten cam bolts. Please stop when you feel tight" 2 Insert screw (2) through pre-drill hole on cleat of bottom rail (G), Attach bottom rail (G) to bottom panel (E) by inserting wood dowel ()& screw (2). Tighten it by rotating screw (2) with Philips screwdriver ( not included) G E Figure 1 Figure 2 8 9 3 4 B 5 6 Insert cam locks (5) into predrilled holes on bottom shelf (E).& shelf panel (D) Screw cam bolt (4) into pre-drilled holes on side panel-left (B). Attach bottom panel (E)& shelf panel (D)to side panel-left (B) by inserting wood dowel () & cam bolt (4) into corresponding pre-drilled holes until bottom panel (E) & shelf panel (D)& side panel-left (B) meet. Secure by rotating cam lock (5) clockwise with Phillips screwdriver(not included) Attach top rail (F) to side panel-left (B) using bolt (8)& spring washer(9)&flat washer(3)&wood dowel (). Tighten bolt (8) with Allen wrench (6). Attach bottom rail (G) to side panel-left (B) using bolt (1)& spring washer(9)&flat washer(3)&wood dowel (). Tighten bolt (1) with Allen wrench (6). 4
Repeat with side panel-right(c).assemble step to be same as with figure 2. 4 C F D 5 3 6 19 Figure3 2 L A Insert screw (2) through predrill holes on rail(l). Attach rail (L) to top panel(a) by inserting wood dowel ()& screw (2). Tighten with Philips screwdriver (not included). Figure4 5
Insert cam locks (5) into predrilled holes on preassembled on figure (3). M Screw cam bolt (4) into pre-drilled holes on top panel (A). Attach preassembly unit on figure (3) to top panel (A) by inserting wood dowel () & cam bolt (4) into corresponding pre-drilled holes until preassembled unit on figure (3) & top panel (A) meet. Secure by rotating cam lock (5) clockwise with Phillips screwdriver(not included) Insert screw(2) through predrilled holes 5 on cleat of top rail (E ) to tighten preassembled unit on figure (3) to top panel (A) by rotating screw (2) with 4 Philips screwdriver(not included) Assembly the leg (M) to preassembled on figure (3) by rotating leg (M) as shown. Figure5 insert the drawer bottom pane (I) into the corresponding groove of drawer side panel (J)& drawer front panel (H), insert male slide (K) in female slide on bottom of drawer bottom(i). H Insert cam locks (5) into predrilled holes J on drawer side (J). Screw cam bolt (4) into pre-drilled holes on drawer front (H). J I K Attach drawer side (J) to drawer front (H) by cam bolt (4) into corresponding pre-drilled holes until preassembled unit drawer side (J) & drawer front (H) meet. H Secure by rotating cam lock (5) clockwise with Phillips screwdriver (not included) Cover the cam-lock hole with plastic cover (10) Figure6 6
Put drawers into cabinet as shown If you use the AG-3-DRAWER STORAGE ORGANIZER as a single unit, please cover the hole on side panel with PVC cover (10). 10 Figure Now you AG-3-DRAWER STORAGE ORGANIZER is ready to use. Figure8
Parts Replacement Form Customer Information Name Address City/State/Zip Code Phone Number Please indicate where you purchased this item: Store/Website/Catalog Please indicate color/size/style number: Style No Parts Letter Parts Description Needed Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise. Please contact Southern Enterprises at 800-633-5096 or in Dallas 92-869-0111/ 9am 4pm Mon-Fri Central time if you have product issues or email us at service@seidal.com. Please ask for customer service representative for issues involving damages or replacement parts. Please ask for technical assistance representative for any issues with product and assembly/construction. Please contact the retailer that you purchased from for returns. Customer Service 1-800-633-5096 service@seidal.com Southern Enterprises, Inc. 600 Freeport Parkway, Suite 200 Coppell, Texas 5019 8