INSTRUCTIONS FOR USE AND GUARANTEE The products contained in this technical manual are manufactured (see Technical Manual); according to the manufacturer s technical specifications. - Inadequate storing or exposure of the products to atmospheric The manufacturer guarantees the repair and, if he considers agents during transport or handling when the products are being necessary, the replacement of any product which have been collected by the carrier or, where applicable, when the delivery shown to be defective within a 30 -days period established note is being signed. under Article 342 of the Spanish Code of Commerce. Under no circumstances the guarantee shall be in force after a year starting from the date of the product manufacturing. LEVELS OF MAINTENANCE WITH FITTED ACCESSORIES The guarantee covers both; labor and any other materials or Doors fitted with the following accessories are considered spare parts used to repair or to replace the product. The standard technicians travel and accommodation expenses will be at the buyer s expense. -Handle- Cylinders -Vision panel - Lock NORMAS DE USO Y GARANTÍA A preventive maintenance of the product shall be made in order to renew the former guarantee, regardless whether the product has been fitted or in storage. This guarantee renewal will be only valid if the maintenance is carried out by the manufacturer or staff duly authorized by him. The frequency of this preventive maintenance is fixed according to the number of cycles to be performed by a door in accordance with the following schedule: LEVEL User s Intensive Heavy CYCLES Less than 15.000 cycle annually Up to 30.000 cycles annually Between 30.000 a 60.000 cycles annually FREQUENCY Annual Biannual Quarterly If the following accessories are fitted, the manufacturer recommends a more frequent maintenance - Door-closer -Electro-magnets -Selectors Doors fitted with the above fittings require reinforcement plates in the door leaf and it will be required to duplicate the maintenance frequency specified in the annual cycle frequency table. For fire doors, that perform between 50,000/80,000 cycles annually or those which are exposed to extreme use conditions such as the case of schools, universities, hospitals, supermarkets, etc., Puertas Padilla requires the following improvements (detailed in the Technical Manual); DOORS OF INTENSIVE OR HEAVY USE We have to consider the following: 1.- Levels of use higher than 60.000 cycles annually are understood to be special, so the frequency of maintenance or the improvements to be made will be determined by the manufacturer s technical department in each case. 2.- The level of maintenance may vary according to the accessories fitted to the product after its manufacture. Under no circumstance the manufacturer will assume responsibilities for defects due to: - Inadequate fitting of the product, that is to say, not fitting the product according to the manufacturer s instructions (see instructions for assembly); - The use of accessories not approved by the manufacturer For single leaf doors; in order to improve the mechanical condition, it is necessary a higher thickness of the sheet, at least 1mm. In case of requirement of accessories, it is extremely important that the fixing and the installation of the accessories are able to support the mentioned level of use (see Technical Department). For double leaf doors; in order to improve the mechanical conditions of the set, it is necessary to increase the thickness sheet of the leaf, at least 1mm. In order to allow the proper operation of the door in the course of time, It will be also necessary the installation of door-closers of 5CEN level. In these cases, the maintenance will be, at least, every three months; if necessary, it can be increased depending on the accessories and the degree. 4 ( E d_ 07/06 )
TRANSPORTATION AND STORAGE TRANSPORTATION AND STORAGE INSTRUCTIONS -Any superficial finish type does not avoid damages caused by an inappropriate transport or storage. CONDICIONES, NORMAS Y TRANSPORTE -The door shall be storage in a dry place against bad weather and humid conditions. -Move with adequate machinery -Do not overlay pallets; respect the composition of the received pallets. INSTALLATION CONDITIONS -Doors have been prepared to be fitted indoor. -Direct exposure to sunlight and humidity can cause sporadic waves in the sheet that may lead into a deformation of the sheet. -Direct exposure to sunlight and humidity can cause a degradation of the internal components of the door. -Doorsets must be protected against bad weather to avoid water leakage into the door. A cover should be provided during the installation. -Between the leaf and the frame can be a different tonality derived from the differences of the finishing or process of a paint application. 5
REVER DOORS UNE-EN 1634-1, UNI 9.723, NF y PN MULTIUSE, EI2 60, EI2 120 6
REVER MULTIUSE REVER 2 3 4 =1min. STANDARD HARDWARE - Standard lock CR1 TESA model CF50, CEN 12209 (See Lock Section, page 85) - Multiuse B-05 hinge Galvanized steel material (See Hinge Section page 74) - Multiuse M0 handles Polypropylene material black color OPTIONAL HARDWARE -Panic bar CEN 1125 (See Panic Bar Section, page 91) -Door-closers CEN 1154 (See Door Closers Section page 115) 7 ( E d_ 07/06 )
DESCRIPTION MULTIUSE -1.2 High resistant reversible metal frame combined with cold smoke seal. -Frame is provided with 4 dead-end clamps 1.5mm thick. -Leaf of 53mm thickness made of galvanized steel of 0.5 mm skin pass type, filled with expansible polystyrene, 51mm thickness. - CEN approved lock, black color anti-coupling handle and cylinder patent key. -Instructions for fitting and maintenance -Weight frame, 18kg/m2 VERTICAL SECTION REVER HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Hfm= Overall aperture H= Nominal height of the leaf Hp= Clear Opening Ht= Heigt of external frame Lp= Clear opening Lfm= Overall aperture Finished Floor * To check the Clear opening at 90 and 180 see pages 25 and 26. STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 4 Clamps of 1,5 mm Fixed with 12 screws (6 for fitting) FINISHING ECO REVER, the frame and leaf present a galvanized finishing. CLASSIC REVER, the frame and leaf present finishes in RAL 7035. * For technical description of these finishes see page 61. ACCESORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel 8 * For technical description of these accessories see page 90. ( E d_ 07/06 )
DESCRIPTION EI2 60-1.2 High resistant reversible metal frame combined with cold smoke seal. -Frame is provided with 4 dead-end clamps, 1.5mm thick. -Leaf of 53mm thickness, made of galvanized steel of 0.7 mm skin pass type. -Internal insulation filled with rock wool, density of 150kg/m3, thickness of 50mm. -Intumescent seal peripheral between the frame and the leaf of 20x2mm. -1 anti-crowbar device -CEN approved lock, black color anti-coupling handle and cylinder patent key. -Instructions for fitting and maintenance -Leaf weight, 25kg/m2 VERTICAL SECTION REVER HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Lp= Clear opening Hfm= Overall aperture H= Nominal height of the leaf Hp= Clear Opening Ht= Heigt of external frame Lfm= Overall aperture Finished Floor * To check the Clear opening at 90 and 180 see pages 25 and 26. STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 4 Clamps of 1,5 mm Fixed with 12 screws (6 for fitting) FINISHING CLASSIC REVER, the frame and leaf present finishes in RAL 7035. * For technical description of these finishes see page 61. ACCESORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel 9 * For technical description of these accessories see page 90. ( E d_ 07/06 )
DESCRIPTION EI2 120 -Reversible frame combined with 1.2 high resistant steel with cold smoke seal, -The frame is provided with 8 dead-end clamps of 1.5mm of thickness. -63mm thick leaf made of galvanized steel of 0.7 mm skin pass type. -Internal insulation filled with rock wool, density of 180kg/m3, 30 +30mm thickness. - Peripheral intumescent seal between the frame and the leaf of 30 x 2mm. -2 anti-crowbars devices -CEN approved lock, black color anti-coupling handle and cylinder patent key. -Instructions for fitting and maintenance -Leaf weight, 25kg/m2 VERTICAL SECTION REVER HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Lp= Clear opening Hfm= Overall aperture H= Nominal height of the leaf Hp= Clear Opening Ht= Heigt of external frame Lfm= Overall aperture * To check the Clear opening at 90 and 180 see pages 25 and 26. Finished Floor STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 4 Clamps of 1,5 mm Fixed with 12 screws (6 for fitting) FINISHING CLASSIC REVER, the frame and leaf present finishes in RAL 7035. * For technical description of these finishes see page 61. ACCESORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel * For technical description of these accessories see page 90. 10 ( E d_ 07/06 )
SINGLE LEAF DOORS WITH REVER FRAME Multiuse, EI2 60, EI2 120 REVER Lt= Width of external frame VERTICAL SECTION Ht= Heigt of external frame Ht/2 (Ht/2)+50 Hfm= Overall aperture H= Nominal height of the leaf Hp= Clear Opening Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Lp= Clear opening Lfm= Overall aperture 11 ( E d_ 07/06 )
SINGLE LEAF DOORS WITH REVER FRAME Multiuse, EI2 60, EI2 120 REVER GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp External frame Lt x Ht L x H L x (H+10) (L-85) x (H-33) (L+50) x H STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp External frame Lt x Ht 800 x 2050 890 x 2050 990 x 2050 1100 x 2050 1200 x 2050 1300 x 2050 800 x 2140 890 x 2140 990 x 2140 1100 x 2140 1200 x 2140 1300 x 2140 800 x 2060 890 x 2060 990 x 2060 1100 x 2060 1200 x 2060 1300 x 2060 800 x 2150 890 x 2150 990 x 2150 1100 x 2150 1200 x 2150 1300 x 2150 715 x 2017 805 x 2017 905 x 2017 1015 x 2017 1115 x 2017 1215 x 2017 715 x 2107 805 x 2107 905 x 2107 1015 x 2107 1115 x 2107 1215 x 2107 850 x 2050 940 x 2050 1040 x 2050 1150 x 2050 1250 x 2050 1350 x 2050 850 x 2140 940 x 2140 1040 x 2140 1150 x 2140 1250 x 2140 1350 x 2140 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Nominal L x H Lfm x Hfm (Lfm+50) x (Hfm-10) (Lfm-85) x (Hfm-43) Lfm x (Hfm-10) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Clear opening Overall aperture Lfm x Hfm External Frame Lt x Ht Nominal leaf L x H Lp x Hp (Lp+85) x (Hp+43) (Lp+135) x (Hp+33) (Lp+85) x (Hp+33) 12 ( E d_ 07/06 )
STANDARD DOOR UNE-EN 1634-1, UNI 9.723, NF y PN MULTIUSE, EI2 60, EI2 90, EI2 120 13
CERTIFICATE MULTIUSE Single leaf and double leaf STANDARD DOORS SINGLE LEAF DOUBLE LEAF Left hand opening (SX) Right hand opening (DX) Left hand opening (SX) Right hand opening (DX) STANDARD HARDWARE - Standard lock CR1 TESA model CF50, CEN 12209 (See Lock Section, page 85) - Multiuse B-05 hinge Galvanized steel material (See Hinge Section page 74) - Multiuse M0 handles Polypropylene material black color OPTIONAL HARDWARE -Panic bar CEN 1125 (See Panic Bar Section, page 91) -Door-closers CEN 1154 (See Door Closers Section page 115) -Closer selector CEN 1158 (See section Hinge page 74) 14 ( E d_ 07/06 )
DESCRIPTION Multiuse single leaf -MC3 frame is manufactured with a1.2mm high resistant steel and completed cold smoke seal. Frame provided with 4 dead-end clamps of 1.5 thickness with a maximum of 2400mm height. Over this height the frame is provided with 6 dead-end clamps. -The doors of a nominal height over 2400mm are provided with an additional hinge. -Leaf of 53mm thick; manufactured in galvanized steel of 0.5 mm skin pass type. -Expansible Polystyrene, 51mm thickness. -CEN approved lock and cylinder patent key VERTICAL SECTION STANDARD DOORS LINEA CLASSIC HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Hfm= Overall aperture Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Lp= Clear opening Lfm= Overall aperture Finished Floor STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 4 Clamps of 1,5 mm Fixed with 12 screws (6 for fitting) FRAMES MC3 (Standard) Type "B" Type "C" Type "M" * For technical description of these finishes see page 47. FINISHES CLASSIC, frame and leaf is provided in RAL 7035. GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system * For technical description of these finishes see page 47. ACCESSORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel 15 * For technical description of these accessories see page 90. ( E d_ 07/06 )
DESCRIPTION Multiuse double leaf -MC3 frame is manufactured with 1.2mm high strength steel and completed with cold smoke seal. -Frame provided with 11 dead-end clamps of 1.5 thickness with a maximum of 2400mm height. Over this height the frame is provided with 13 dead-end clamps. -The doors of a nominal height over 2400mm are provided with and additional hinge per leaf. -Leaf of 53mm thick; manufactured in galvanized steel of 0.5 mm skin pass type. -Expansible Polystyrene, 51mm thick. -CEN approved lock and cylinder patent key. -Second leaf manufactured with superior and lower locks with manual activation. -Instructions for fitting and maintenance -Leaf weight, 18kg/m2 HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L1= Primary nominal width of the leaf L2= Secondary nominal width of the leaf Hfm= Overall aperture VERTICAL SECTION Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame STANDARD DOORS LINEA CLASSIC Lp= Clear opening Lfm= Overall aperture Finished Floor STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 11 Clamps of 1,5 mm Fixed with 15 screws (6 for fitting and 3 in the lintel) FRAMES MC3 (Standard) Type "B" Type "C" Type "M" * For technical description of these finishes see page 47. FINISHES CLASSIC, frame and leaf is provided in RAL 7035. GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system * For technical description of these finishes see page 47. ACCESSORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel 16 * For technical description of these accessories see page 90. ( E d_ 07/06 )
DESCRIPTION EI2 60 Single leaf -Three sides MC3 frame manufactured with 1.2mm high resistance steel and completed with cold smoke seal. -Frame provided with 6 dead-end clamps of 1.5 thickness with a maximum of 2400mm height. Over this height, the frame is provided with 8 dead-end clamps. -The doors of a nominal height over 2400mm are provided with and additional hinge. -Leaf manufactured in galvanized steel sheet skin pass type, Ral COLOR 7035, 53 mm thickness. -Rock wool insulation. -Intumescent seal in EI2 60:20 x 2mm frame. -CEN approved EI hinge. -CEN approved lock and cylinder patent key. - DIN standard Fire resistant door handles provided in steel core of Polyamide. -1 anti-crow bar device -Separators to facilitate an easy installation. -Metallic identification sheet with standardization EI2 -Full instructions for fitting and maintenance of the unit are provided. - Door leaf weight 25 kg/m2. HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Hfm= Overall aperture VERTICAL SECTION Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame STANDARD DOORS LINEA CLASSIC Lp= Clear opening Lfm= Overall aperture Finished Floor STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 6 Clamps of 1,5 mm Fixed with 12 screws (6 for fitting) FRAMES MC3 (Standard) Type "B" * For technical description of these finishes see page 47. FINISHES CLASSIC, frame and leaf is provided in RAL 7035. GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system * For technical description of these finishes see page 47. ACCESSORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel 17 * For technical description of these accessories see page 90. ( E d_ 07/06 )
DESCRIPTION -Three sides MC3 frame is manufactured from 1.2mm high strength steel and is completed with cold smoke seal. -Frame provided with 6 Dead-end clamps of 1.5 thickness with a maximum of 2400mm height. Over this height the frame is provided with 13 dead-end clamps. -The doors of a nominal height over 2400mm are provided with and additional hinge per leaf. -Leaf manufactured in galvanized steel sheet skin pass type, Ral COLOR 7035, 53 mm of thickness. -Rock wool insulation. -Intumescent seal in EI2 60:20 x 2mm frame. -CEN approved hinge. -CEN approved lock. - DIN standard fire resistant door handles provided in steel core of polyamide. -1 anti-crow bar device -Separators to facilitate an easy installation. -Secondary leaf provided with CR4 and bars with superior and lower closing. -Metallic identification sheet with standardization EI2 -Full instructions for fitting and maintenance of the unit are provided. - Door leaf weight 25 kg/m2. HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L1= Primary nominal width of the leaf EI2 60 Double Leaf L2= Secondary nominal width of the leaf Hfm= Overall aperture VERTICAL SECTION Hp= Clear Opening H= Nominal height of the leaf LINEA CLASSIC Ht= Heigt of external frame STANDARD DOORS Lp= Clear opening Lfm= Overall aperture Finished Floor STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 11 Clamps of 1,5 mm Fixed with 15 screws (6 for fitting and 3 in the lintel) FRAMES MC3 (Standard) Type "B" Type "C" Type "M" * For technical description of these finishes see page 47. FINISHES CLASSIC, frame and leaf is provided in RAL 7035. GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system * For technical description of these finishes see page 47. ACCESSORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel - 18 * For technical description of these accessories see page 90. ( E d_ 07/06 )
DESCRIPTION EI2 120 Single leaf -Three sides MC3 frame is manufactured with 1.2mm high resistant steel and is completed with cold smoke seal. -Frame provided with 8 dead-end clamps of 1.5 thickness with a maximum of 2400mm height. Over this height the frame is provided with 10 dead-end clamps. -The doors of a nominal height over 2400mm are provided with an additional hinge. -Leaf manufactured in galvanized steel sheet skin pass type, Ral COLOR 7035, 63 mm of thickness. -Rock wool insulation. -Intumescent seal in EI2 120:30 x 2mm frame. -CEN approved hinge. -CEN approved lock and patent key cylinder. - DIN standard fire resistant door handles provided in steel core of Polyamide. -2 anti-crow bar devices -Separators to facilitate an easy installation. -Metallic identification sheet with standardization EI2 -Full instructions for fitting and maintenance of the unit are provided. - Door leaf weight 30 kg/m2. HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Hfm= Overall aperture VERTICAL SECTION Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame STANDARD DOORS LINEA CLASSIC Lp= Clear opening Finished Floor Lfm= Overall aperture STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 8 Clamps of 1,5 mm Fixed with 15 screws (6 for fitting) FRAMES MC3 (Standard) Stainless steel MC3 Stainless stee Type "B" Type "C" Type "M" FINISHES CLASSIC, frame and leaf is provided in RAL 7035. GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system STAINLESS STEEL, frame and sheet are presented in fingerprint-resistant stainless steel AISI 304 * For technical description of these finishes see page 47. ACCESSORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel 19 * For technical description of these accessories see page 90. ( E d_ 07/06 )
DESCRIPTION -Three sides MC3 frame manufactured with 1.2mm high resistant steel and completed with cold smoke seal. -Frame provided with 13 dead-end clamps of 1.5 thickness with a maximum of 2400mm height. Over this height the frame is provided with 15 dead-end clamps. -The doors of a nominal height over 2400mm are provided with an additional hinge per leaf. -Leaf manufactured in galvanized steel sheet skin pass type, Ral COLOR 7035, 63 mm thickness. -Rock wool insulation. -Intumescent seal in EI2 120:30 x 2mm frame. -CEN approved EI hinge. -CEN approved lock and cylinder patent key. - DIN Standard Fire resistant door handles provided in steel core of Polyamide. -2 anti-crow bar devices -Separators to facilitate an easy installation. -Metallic identification sheet with standardization EI2 EI2 120 Single leaf -Full instructions for fitting and maintenance of the unit are provided. - Door leaf weight EI2 120 30 kg/m2. HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L1= Primary nominal width of the leaf L2= Secondary nominal width of the leaf Hfm= Overall aperture VERTICAL SECTION Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame STANDARD DOORS Lp= Clear opening Lfm= Overall aperture Finished Floor STANDARD FRAME FIXATION WITH CLAMPS OPTIONAL FIXED WITH SCREWS SCREWS NOT INCLUDED 13 Clamps of 1,5 mm Fixed with 15 screws (6 for fitting and 3 in the lintel) FRAMES MC3 (Standard) Type "B" Type "C" Type "M" * For technical description of these finishes see page 47. FINISHES CLASSIC, frame and leaf is provided in RAL 7035. GAMMACOLOR, frame and leaf are provided in RAL goffered epoxy- polyester range INNOVA, there are optional frame colors according to RAL chart and leaf in digital printing system STAINLESS STEEL, frame and sheet are presented in fingerprint-resistant stainless steel AISI 304 * For technical description of these finishes see page 47. ACCESSORIES - MC6 Embracing frame -Panic bar -locks -Door-closers -Vision panel 20 * For technical description of these accessories see page 90. ( E d_ 07/06 )
FRAME DIMENSIONS MC3 Lt= Width of external frame Single leaf standard doors: Multiuse, EI2 60, EI2 90, EI2 120 VERTICAL SECTION Ht= Heigt of external frame 1025 1075 Hfm= Overall aperture Hp= Clear Opening DIMENSIONS H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Lp= Clear opening Lfm= Overall aperture 21 ( E d_ 07/06 )
MC3 FRAME DIMENSIONS GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. Standard single leaf doors: Multiuse, EI2 60, EI2 120 DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp Internal Frame Lp x Hp External frame Lt x Ht L x H L x (H+10) (L-85) x (H-33,5) (L-15) x (H+3) (L+50) x (H+34) STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp Internal Frame Lp x Hp External frame Lt x Ht 800 x 2050 890 x 2050 990 x 2050 1100 x 2050 1200 x 2050 1300 x 2050 800 x 2140 890 x 2140 990 x 2140 1100 x 2140 1200 x 2140 1300 x 2140 800 x 2060 890 x 2060 990 x 2060 1100 x 2060 1200 x 2060 1300 x 2060 800 x 2150 890 x 2150 990 x 2150 1100 x 2150 1200 x 2150 1300 x 2150 715 x 2016,5 805 x 2016,5 905 x 2016,5 1015 x 2016,5 1115 x 2016,5 1215 x 2016,5 715 x 2106,5 805 x 2106,5 905 x 2106,5 1015 x 2106,5 1115 x 2106,5 1215 x 2106,5 785 x 2053 875 x 2053 975 x 2053 1085 x 2053 1185 x 2053 1285 x 2053 785 x 2143 875 x 2143 975 x 2143 1085 x 2143 1185 x 2143 1285 x 2143 850 x 2084 940 x 2084 1040 x 2084 1150 x 2084 1250 x 2084 1350 x 2084 850 x 2174 940 x 2174 1040 x 2174 1150 x 2174 1250 x 2174 1350 x 2174 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Internal Frame Lp x Hp Nominal L x H Lfm x Hfm (Lfm+50) x (Hfm+24) (Lfm-85) x (Hfm-43,5) (Lfm-15) x (Hfm-7) Lfm x (Hfm-10) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Clear opening Overall aperture Lfm x Hfm External Frame Lt x Ht Internal Frame Lp x Hp Nominal leaf L x H Lp x Hp (Lp+85) x (Hp+43,5) (Lp+135) x (Hp+67,5) (Lp+70) x (Hp+36) (Lp+85) x (Hp+33,5) 22 ( E d_ 07/06 )
MC3 FRAME DIMENSIONS Standard single leaf doors: Multiuse, EI2 60, EI2 120 DIMENSIONS Lt= Width of external frame VERTICAL SECTION L1 = Primary Nominal width L2 = Secondary nominal width 1075 1025 Ht= Heigt of external frame Hfm= Overall aperture interno marco Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L1= Primary nominal width of the leaf L2= Secondary nominal width of the leaf Lpa= Primary clear opening Lp= Clear opening Lfm= Overall aperture 23 ( E d_ 07/06 )
Standard single leaf doors: MC3 FRAME DIMENSIONS Multiuse, EI2 60, EI2 120 GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. Nominal leaf (L1+ L2) x H Overall aperture Lfm x Hfm (L1+L2+10) x (H+10) Primary clear opening Lpa L1-87 Clear opening Lp x Hp (L1+L2-78) x (H-33,5) Internal Frame Li x Hi (L1+L2-2) x (H+3) External Frame Lt x Ht (L1+ L2+60) x (H+34) DIMENSIONS STANDARD DIMENSIONS *for the case of double leaf EI2 120; 10 mm shall be added Nominal leaf (L1+L2) x H Overall aperture Lfm x Hfm Primary clear opening Lpa Clear opening Lp x Hp Internal Frame Lp x Hp External Frame Lt x Ht 600+590* (1190*) x 2050 1200* x 2060 513 1112* x 2016.5 1188* x 2053 1250* x 2084 800+400 (1200) x 2050 1210 x 2060 713 1122 x 2016.5 1188 x 2053 1260 x 2084 650+640* (1290*) x 2050 1300* x 2060 563 1212* x 2016.5 1288* x 2053 1350* x 2084 890+400 (1290) x 2050 1300 x 2060 803 1212 x 2016.5 1288 x 2053 1350 x 2084 700+690* (1390*) x 2050 1400* x 2060 613 1312* x 2016.5 1388* x 2053 1450* x 2084 990+400 (1390) x 2050 1400 x 2060 903 1312 x 2016.5 1388 x 2053 1450 x 2084 750+740* (1490*) x 2050 1500* x 2060 663 1412* x 2016.5 1488* x 2053 1550* x 2084 800+790* (1590*) x 2050 1600* x 2060 713 1512* x 2016.5 1588* x 2053 1650* x 2084 890+880* (1770*) x 2050 1780* x 2060 803 1692* x 2016.5 1768* x 2053 1830* x 2084 990+980* (1970*) x 2050 1980* x 2060 903 1892* x 2016.5 1968* x 2053 2030* x 2084 600+590* (1190*) x 2140 1200* x 2150 513 1112* x 2106.5 1188* x 2143 1250* x 2174 800+400 (1200) x 2140 1210 x 2150 713 1122 x 2106.5 1188 x 2143 1260 x 2174 650+640* (1290*) x 2140 1300* x 2150 563 1212* x 2106.5 1288* x 2143 1350* x 2174 890+400 (1290) x 2140 1300 x 2150 803 1212 x 2106.5 1288 x 2143 1350 x 2174 700+690* (1390*) x 2140 1400* x 2150 613 1312* x 2106.5 1388* x 2143 1450* x 2174 990+400 (1390) x 2140 1400 x 2150 903 1312 x 2106.5 1388 x 2143 1450 x 2174 750+740* (1490*) x 2140 1500* x 2150 663 1412* x 2106.5 1488* x 2143 1550* x 2174 800+790* (1590*) x 2140 1600* x 2150 803 1512* x 2106.5 1588* x 2143 1650* x 2174 890+880* (1770*) x 2140 1780* x 2150 903 1692* x 2106.5 1768* x 2143 1830* x 2174 990+980* (1970*) x 2140 1980* x 2150 903 1892* x 2106.5 1968* x 2143 2030* x 2174 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Internal Frame Li x Hi Nominal leaf (L1+L2) x H Lfm x Hfm (Lfm+50) x (Hfm+24) (Lfm-88) x (Hfm-43,5) (Lfm-12) x (Hfm-7) (Lfm-10) x (Hfm-10) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Clear opening Lp x Hp Overall aperture Lfm x Hfm (Lp+88) x (Hp+43,5) External Frame Lt x Ht (Lp+138) x (Hp+67,5) Internal Frame Li x Hi (Lp+76) x (Hp+36) Nominal leaf (L1+L2) x H (Lp+78) x (Hp+33,5) 24 ( E d_ 07/06 )
SINGLE LEAF APERTURE With MC3 and Rever frames, 180º, 125º and 90º All the measures are approximated and are expressed in mm INSTALLATION FOR APERTURE UP TO 180º (It is necessary to be fitted into the wall) Lfm + 25 STANDARD DOORS LINEA CLASSIC 25(*) Door-closer Lp= Lfm - 85 175 (*) L - 230 (*) Lfm INSTALLATION FOR MAXIMUM CLEAR OPENING - Aperture minimum of 125º STANDARD DIMENSION NOMINAL WIDTH D D (**) Lp= Lfm - 85 Lfm (**) Maximum distance of separation between the Overall aperture and the closest wall near to the Hinges. If the door includes a panic bar, maximum clear opening will not be obtained 800 890 990 1100 1200 1300 L= Lfm 460 520 570 640 690 750 INSTALATION IN CORRIDOR - APERTURE UP TO 90º 90 aperture in corridor of excellent width (It is not required to be fitted into the wall) 90 aperture in a corridor with a minimum width (It is required to be installed into the wall) 85 Width of corridor= Lfm +150 50 Width of corridor= Lfm +80 175 50 Cierrapuertas 50 L - 190 Cierrapuertas A B Lp = Lfm -85 -A-B A B Lp = Lfm -85 -A-B Lfm Lfm A= 29 for EI20-120 A= 19 for EI2-60 B= differs depending on the handle or the installed bar (see accessories section). (example B= 100 for panic bar SR Series B= 70 for standard handle M0 and M1) (*) Measures for PUERTAS PADILLA standard handle 25 Some handles and door closers can require the ( fitting E d_ 07/06 into the ) wall. The installation ALWAYS has to be studied and approved by the Construction department
DOUBLE LEAF APERTURE L1 + 25 With MC3 and Rever frames, 180º, 125º and 90º All the measures are approximated and are expressed in mm INSTALLATION FOR APERTURE UP TO 180º (It is necessary to be fitted into the wall) L2 + 70 STANDARD DOORS LINEA CLASSIC Lp = Lfm - 88 25 Cierrapuertas Cierrapuertas 175 L1-230 Lfm INSTALLATION FOR MAXIMUM CLEAR OPENING - Aperture minimum of 125º STANDARD DIMENSION NOMINAL WIDTH, L1 D1 600 350 STANDARD DIMENSION NOMINAL WIDTH, L2 400 D2 240 700 410 600 360 750 440 Lp = Lfm - 88 700 420 800 460 800 470 890 520 890 530 990 570 * D1 Lfm * D2 990 580 (**) Maximum distance of separation between the Overall aperture and the closest wall near to the Hinges. If the door includes a panic bar, maximum clear opening will not be obtained INSTALATION IN CORRIDOR - APERTURE UP TO 90º 90 aperture in corridor of excellent width (It is not required to be fitted into the wall) 90 aperture in a corridor with a minimum width (It is required to be installed into the wall) 25 85 Width of corridor= Lfm +150 85 50 Width of corridor= Lfm +80 50 175 50 50 L1-190 A B Lp = Lfm - 88-2x(A+B) B A A B Lp = Lfm - 88-2x(A+B) B A Lfm Lfm A= 29 for EI20-120 A= 19 for EI2-60 B= differs depending on the handle or the installed bar (see accessories section). (example B= 100 for panic bar SR Series B= 70 for standard handle M0 and M1) (*) Measures for PUERTAS PADILLA standard handle 26 Some handles and door closers can require the fitting into the wall. The installation ALWAYS has to be studied and approved by the Construction department ( E d_ 07/06 )
STAINLESS STEEL FRAME DIMENSIONS Single leaf standard door: EI2 120 VERTICAL SECTION DIMENSIONS Lt= Width of external frame Ht= Heigt of external frame 1025 1075 Hfm= Overall aperture Internal frame Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Lp= Clear opening Li= Internal frame Lfm= Overall aperture 27 ( E d_ 07/06 )
STAINLESS STEEL MC3 FRAME DIMENSIONS GENERAL DIMENSION TABLE Single leaf standard door: EI2 120 For these dimensions, a tolerance of ±3mm is applicable. DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp Internal Frame Li x Hi External frame Lt x Ht L x H L x (H+10) (L-91) x (H-38) (L-20) x (H-2) (L+55) x (H+35) STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp Internal Frame Li x Hi External frame Lt x Ht 800 x 2050 890 x 2050 990 x 2050 1100 x 2050 1200 x 2050 1300 x 2050 800 x 2140 890 x 2140 990 x 2140 1100 x 2140 1200 x 2140 1300 x 2140 800 x 2060 890 x 2060 990 x 2060 1100 x 2060 1200 x 2060 1300 x 2060 800 x 2150 890 x 2150 990 x 2150 1100 x 2150 1200 x 2150 1300 x 2150 709 x 2012 799 x 2012 899 x 2012 1009 x 2012 1109 x 2012 1209 x 2012 709 x 2102 799 x 2102 899 x 2102 1009 x 2102 1109 x 2102 1209 x 2102 780 x 2048 870 x 2048 970 x 2048 1080 x 2048 1180 x 2048 1280 x 2048 780 x 2138 870 x 2138 970 x 2138 1080 x 2138 1180 x 2138 1280 x 2138 855 x 2085 945 x 2085 1045 x 2085 1155 x 2085 1255 x 2085 1355 x 2085 855 x 2175 945 x 2175 1045 x 2175 1155 x 2175 1255 x 2175 1355 x 2175 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Internal Frame Li x Hi Nominal L x H Lfm x Hfm (Lfm+55) x (Hfm+25) (Lfm-91) x (Hfm-48) (Lfm-20) x (Hfm-12) Lfm x (Hfm-10) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Clear opening Overall aperture Lfm x Hfm External Frame Lt x Ht Internal Frame Li x Hi Nominal leaf L x H Lp x Hp (Lp+91) x (Hp+48) (Lp+146) x (Hp+73) (Lp+71) x (Hp+36) (Lp+91) x (Hp+38) 28 ( E d_ 07/06 )
STAINLESS STEEL MC3 FRAME DIMENSIONS Lt= Width of external frame Double leaf standard door: EI2 120 VERTICAL SECTION DIMENSIONS L1 = Primary Nominal width L2 = Secondary nominal width 1075 1025 Ht= Heigt of external frame Hfm= Overall aperture Internal frame Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L1= Primary nominal width of the leaf L2= Secondary nominal width of the leaf Lpa= Primary clear opening Lp= Clear opening Li= Width of internal frame Lfm= Overall aperture 29 ( E d_ 07/06 )
STAINLESS STEEL MC3 FRAME DIMENSIONS GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. Double leaf standard door: EI2 120 DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Primary clear opening Lpa Clear opening Lp x Hp Internal Frame Li x Hi External Frame Lt x Ht (L1+ L2) x H (L1+ L2+10) x (H+10) L1-87 (L1+L2-80) x (H-38) (L1+L2-9) x (H-2) (L1+ L2+66) x (H+35) STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Primary clear opening Lpa Clear opening Lp x Hp Internal Frame Li x Hi External Frame Lt x Ht 600+600 (1200) x 2050 1210 x 2060 513 1120 x 2012 1191 x 2048 1266 x 2085 800+400 (1200) x 2050 1210 x 2060 713 1120 x 2012 1191 x 2048 1266 x 2085 650+650 (1300) x 2050 1310 x 2060 563 1220 x 2012 1291 x 2048 1366 x 2085 890+400 (1290) x 2050 1300 x 2060 803 1210 x 2012 1281 x 2048 1356 x 2085 700+700 (1400) x 2050 1400 x 2060 613 1320 x 2012 1391 x 2048 1466 x 2085 990+400 (1390) x 2050 1410 x 2060 903 1310 x 2012 1381 x 2048 1456 x 2085 750+750 (1500) x 2050 1510 x 2060 663 1420 x 2012 1491 x 2048 1566 x 2085 800+800 (1600) x 2050 1610 x 2060 713 1520 x 2012 1591 x 2048 1666 x 2085 890+890 (1780) x 2050 1790 x 2060 803 1700 x 2012 1771 x 2048 1846 x 2085 990+990 (1980) x 2050 1990 x 2060 903 1900 x 2012 1971 x 2048 2046 x 2085 600+600 (1200) x 2140 1210 x 2150 513 1120 x 2102 1191 x 2138 1266 x 2175 800+400 (1200) x 2140 1210 x 2150 713 1120 x 2102 1191 x 2138 1266 x 2175 650+650 (1300) x 2140 1310 x 2150 563 1220 x 2102 1291 x 2138 1366 x 2175 890+400 (1290) x 2140 1300 x 2150 803 1210 x 2102 1281 x 2138 1356 x 2175 700+700 (1400) x 2140 1410 x 2150 613 1320 x 2102 1391 x 2138 1466 x 2175 990+400 (1390) x 2140 1400 x 2150 903 1310 x 2102 1381 x 2138 1456 x 2175 750+750 (1500) x 2140 1510 x 2150 663 1420 x 2102 1491 x 2138 1566 x 2175 800+800 (1600) x 2140 1610 x 2150 803 1520 x 2102 1591 x 2138 1666 x 2175 890+890 (1780) x 2140 1790 x 2150 903 1700 x 2102 1771 x 2138 1846 x 2175 990+990 (1980) x 2140 1990 x 2150 903 1900 x 2102 1971 x 2138 2046 x 2175 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Internal Frame Li x Hi Nominal leaf (L1+L2) x H Lfm x Hfm (Lfm+56) x (Hfm+25) (Lfm-90) x (Hfm-48) (Lfm-19) x (Hfm-12) (Lfm-10) x (Hfm-10) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Internal Frame Li x Hi Nominal leaf (L1+L2) x H Lp x Hp (Lp+90) x (Hp+48) (Lp+146) x (Hp+73) (Lp+71) x (Hp+36) (Lp+80) x (Hp+38) 30 ( E d_ 07/06 )
"B" TYPE FRAME DIMENSIONS EI2 30, single leaf DIMENSIONS VERTICAL SECTION Lt= Width of external frame Ht= Heigt of external frame 1025 1075 Hfm= Overall aperture Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Lp= Clear opening Lfm= Overall aperture 31 ( E d_ 07/06 )
"B" TYPE FRAME DIMENSIONS EI2 30, single leaf GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. MEDIDAS DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp External frame Lt x Ht L x H (L+53) x (H+33) (L-87) x (H-37) (L+43) x (H+28) STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp External frame Lt x Ht 800 x 2050 890 x 2050 990 x 2050 1100 x 2050 1200 x 2050 1300 x 2050 800 x 2140 890 x 2140 990 x 2140 1100 x 2140 1200 x 2140 1300 x 2140 853 x 2083 943 x 2083 1043 x 2083 1153 x 2083 1253 x 2083 1353 x 2083 853 x 2173 943 x 2173 1043 x 2173 1153 x 2173 1253 x 2173 1353 x 2173 713 x 2013 803 x 2013 903 x 2013 1013 x 2013 1113 x 2013 1213 x 2013 713 x 2103 803 x 2103 903 x 2103 1013 x 2103 1113 x 2103 1213 x 2103 843 x 2078 933 x 2078 1033 x 2078 1143 x 2078 1243 x 2078 1343 x 2078 843 x 2168 933 x 2168 1033 x 2168 1143 x 2168 1243 x 2168 1343 x 2168 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Nominal L x H Lfm x Hfm (Lfm-10) x (Hfm-5) (Lfm-140) x (Hfm-70) (Lfm-53) x (Hfm-33) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Clear opening Overall aperture Lfm x Hfm External Frame Lt x Ht Nominal leaf L x H Lp x Hp (Lp+140) x (Hp+70) (Lp+130) x (Hp+65) (Lp+87) x (Hp+37) 32 ( E d_ 07/06 )
"B" TYPE FRAME DIMENSIONS Lt= Width of external frame EI2 30, double leaf DIMENSIONS L1 = Primary Nominal width L2 = Secondary nominal width VERTICAL SECTION Ht= Heigt of external frame 1075 1025 Hfm= Overall aperture Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L1= Primary nominal width of the leaf L2= Secondary nominal width of the leaf Lpa= Primary clear opening Lp= Clear opening Lfm= Overall aperture 33 ( E d_ 07/06 )
"B" TYPE FRAME DIMENSIONS EI2 30, double leaf GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. Nominal leaf (L1+ L2) x H Overall aperture Lfm x Hfm (L1+ L2+ 63)x(H+33) Primary clear opening Lpa L1-84 Clear opening Lp x Hp (L1+ L2-77) x (H- 37) External Frame Lt x Ht (L1 + L2 + 53) x (H+28) DIMENSIONS STANDARD DIMENSIONS *for the case of double leaf EI2 120; 10 mm shall be added Nominal leaf Overall aperture Lfm x Hfm Primary clear opening Lpa Clear opening Lp x Hp External Frame Lt x Ht 600+590* (1190*) x 2050 1253* x 2060 516 1113* x 2013 1243* x 2078 800+400 (1200) x 2050 1263 x 2060 716 1123 x 2013 1253 x 2078 650+640* (1290*) x 2050 1353* x 2060 566 1213* x 2013 1343* x 2078 890+400 (1290) x 2050 1353 x 2060 806 1213 x 2013 1343 x 2078 700+690* (1390*) x 2050 1453* x 2060 616 1313* x 2013 1443* x 2078 990+400 (1390) x 2050 1453 x 2060 906 1313 x 2013 1443 x 2078 750+740* (1490*) x 2050 1553* x 2060 666 1413* x 2013 1543* x 2078 800+790* (1590*) x 2050 1653* x 2060 716 1513* x 2013 1643* x 2078 890+880* (1770*) x 2050 1833* x 2060 806 1693* x 2013 1823* x 2078 990+980* (1970*) x 2050 2033* x 2060 906 1893* x 2013 2023* x 2078 600+590* (1190*) x 2140 1253* x 2150 516 1113* x 2103 1243* x 2168 800+400 (1200) x 2140 1263 x 2150 716 1123* x 2103 1253* x 2168 650+640* (1290*) x 2140 1353* x 2150 566 1213* x 2103 1343* x 2168 890+400 (1290) x 2140 1353 x 2150 806 1213* x 2103 1343* x 2168 700+690* (1390*) x 2140 1453* x 2150 616 1313* x 2103 1443* x 2168 990+400 (1390) x 2140 1453 x 2150 906 1313* x 2103 1443* x 2168 750+740* (1490*) x 2140 1553* x 2150 666 1413* x 2103 1543* x 2168 800+790* (1590*) x 2140 1653* x 2150 806 1513* x 2103 1643* x 2168 890+880* (1770*) x 2140 1833* x 2150 906 1693* x 2103 1823* x 2168 990+980* (1970*) x 2140 2033* x 2150 906 1893* x 2103 2023* x 2168 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Nominal leaf (L1+L2) x H Lfm x Hfm (Lfm-10) x (Hfm-5) (Lfm -140) x (Hfm-70) (Lfm-63) x (Hfm-33) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture Clear opening Lfm x Hfm External Frame Lt x Ht Nominal leaf (L1+L2) x H Lp x Hp (Lp+140) x (Hp+70) (Lp+130) x (Hp+65) (Lp+77) x (Hp+37) 34 ( E d_ 07/06 )
SINGLE LEAF APERTURE All the measures are approximated and are expressed in mm with B TYPE frame 180º, 120º and 90º INSTALLATION FOR APERTURE UP TO 180º (It is necessary to be fitted into the wall) Lfm STANDARD DOOR LINEA CLASSIC Lfm-140 Según modelo de cierrapuertas Lfm 175(*) Lfm-300(*) Lfm-50 INSTALLATION FOR MAXIMUM CLEAR OPENING - Aperture minimum of 120º Lfm-20 Lfm-140 Lfm-340 Lfm INSTALATION IN CORRIDOR - APERTURE UP TO 90º Lfm-20 Lfm-250(*) 175(*) Según modelo de cierrapuertas A B Lfm-140-A-B Lp=Lfm-140 Lfm A= 29 for EI20-120 A= 19 for EI2-60 B= differs depending on the handle or the installed bar (see accessories section). (example B= 100 for panic bar SR Series B= 70 for standard handle M0 and M1) (*) Measures for PUERTAS PADILLA standard handle Some handles and door closers can require the fitting into the wall. The installation ALWAYS has to be studied and approved by the Construction department ( E d_ 07/06 ) 35
DOUBLE LEAF APERTURE All the measures are approximated and are expressed in mm with B TYPE frames, 180º, 120º and 90º INSTALLATION FOR APERTURE UP TO 180º (It is necessary to be fitted into the wall) STANDARD DOOR LINEA CLASSIC Según modelo de cierrapuertas Lfm -140 Según modelo de cierrapuertas 175(*) L1-250(*) Lfm L2+50 INSTALLATION FOR MAXIMUM CLEAR OPENING - Aperture minimum of 120º (L1/2) + Lfm + (L2/2) L1 + 40 L2 + 90 Lfm-140 L1/2 Lfm L2/2 If the door includes panic bar, maximum net clear opening cannot be obtained INSTALLATION IN CORRIDOR - APERTURE UP TO 90º L1+40 175(*) L1-190 (*) Lfm-140-(2xA)-(2xB) L2+90 A B Lfm-A-B-L2-150 B A Lfm A= 29 for EI20-120 A= 19 for EI2-60 B= differs depending on the handle or the installed bar (see accessories section). (example B= 100 for panic bar SR Series B= 70 for standard handle M0 and M1) (*) Measures for PUERTAS PADILLA standard handle 36 Some handles and door closers can require the fitting into the wall. The installation ALWAYS has to be studied and approved by the Construction department ( E d_ 07/06 )
"C" TYPE FRAME DIMENSIONS EI2 120 Single leaf DIMENSIONS VERTICAL SECTION Lt= Width of external frame Ht= Heigt of external frame 1025 1075 Hfm= Overall aperture Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Lp= Clear opening Lfm= Overall aperture 37 ( E d_ 07/06 )
"C" TYPE FRAME DIMENSIONS EI2 120 Single leaf DIMENSIONS GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp External frame Lt x Ht L x H (L-25) x (H-3) (L-107) x (H-45) (L+53) x (H+35) STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp External frame Lt x Ht 800 x 2050 890 x 2050 990 x 2050 1100 x 2050 1200 x 2050 1300 x 2050 800 x 2140 890 x 2140 990 x 2140 1100 x 2140 1200 x 2140 1300 x 2140 775 x 2047 865 x 2047 965 x 2047 1075 x 2047 1175 x 2047 1275 x 2047 775 x 2137 865 x 2137 965 x 2137 1075 x 2137 1175 x 2137 1275 x 2137 693 x 2005 783 x 2005 883 x 2005 993 x 2005 1093 x 2005 1193 x 2005 693 x 2095 783 x 2095 883 x 2095 993 x 2095 1093 x 2095 1193 x 2095 853 x 2085 943 x 2085 1043 x 2085 1153 x 2085 1253 x 2085 1353 x 2085 853 x 2175 943 x 2175 1043 x 2175 1153 x 2175 1253 x 2175 1353 x 2175 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Nominal L x H Lfm x Hfm (Lfm+78) x (Hfm+38) (Lfm-82) x (Hfm-42) (Lfm+25) x (Hfm+3) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Clear opening Overall aperture Lfm x Hfm External Frame Lt x Ht Nominal leaf L x H Lp x Hp (Lp+82) x (Hp+42) (Lp+160) x (Hp+80) (Lp+107) x (Hp+45) 38 ( E d_ 07/06 )
"C" TYPE FRAME DIMENSIONS EI2 120 Double leaf DIMENSIONS Lt= Width of external frame VERTICAL SECTION L1 = Primary Nominal width L2 = Secondary nominal width 1075 1025 Ht= Heigt of external frame Hfm= Overall aperture Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L1= Primary nominal width of the leaf L2= Secondary nominal width of the leaf Lpa= Primary clear opening Lp= Clear opening Lfm= Overall aperture 39 ( E d_ 07/06 )
"C" TYPE FRAME DIMENSIONS EI2 120 Double leaf GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Primary clear opening Lpa Clear opening Lp x Hp External Frame Lt x Ht (L1+ L2) x H (L1+L2-15) x (H-3) L1-87 (L1+L2-95) x (H-45) (L1+L2+65) x (H+35) STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Primary clear opening Lpa Clear opening Lp x Hp External Frame Lt x Ht 600+600 (1200) x 2050 1185 x 2047 513 1105 x 2005 1265 x 2085 800+400 (1200) x 2050 1185 x 2047 713 1105 x 2005 1265 x 2085 650+650 (1300) x 2050 1285 x 2047 563 1205 x 2005 1365 x 2085 890+400 (1290) x 2050 1275 x 2047 803 1195 x 2005 1355 x 2085 700+700 (1400) x 2050 1385 x 2047 613 1305 x 2005 1465 x 2085 990+400 (1390) x 2050 1375 x 2047 903 1295 x 2005 1465 x 2085 750+750 (1500) x 2050 1485 x 2047 663 1405 x 2005 1565 x 2085 800+800 (1600) x 2050 1585 x 2047 713 1505 x 2005 1665 x 2085 890+890 (1780) x 2050 1765 x 2047 803 1685 x 2005 1845 x 2085 990+990 (1980) x 2050 1965 x 2047 903 1885 x 2005 2045 x 2085 600+600 (1200) x 2140 1185 x 2137 513 1105 x 2095 1265 x 2175 800+400 (1200) x 2140 1185 x 2137 713 1105 x 2095 1275 x 2175 650+650 (1300) x 2140 1285 x 2137 563 1205 x 2095 1375 x 2175 890+400 (1290) x 2140 1275 x 2137 803 1195 x 2095 1375 x 2175 700+700 (1400) x 2140 1385 x 2137 613 1305 x 2095 1475 x 2175 990+400 (1390) x 2140 1375 x 2137 903 1295 x 2095 1475 x 2175 750+750 (1500) x 2140 1485 x 2137 663 1405 x 2095 1575 x 2175 800+800 (1600) x 2140 1585 x 2137 803 1505 x 2095 1675 x 2175 890+890 (1780) x 2140 1765 x 2137 903 1685 x 2095 1875 x 2175 990+990 (1980) x 2140 1965 x 2137 903 1885 x 2095 2045 x 2175 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Nominal leaf (L1+L2) x H Lfm x Hfm (Lfm+80) x (Hfm+38) (Lfm -80) x (Hfm-42) (Lfm+15) x (Hfm+3) TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture Lp x Hp Clear opening Lfm x Hfm (Lp+80) x (Hp+42) External Frame Lt x Ht (Lp+160) x (Hp+80) Nominal leaf (L1+L2) x H (Lp+95) x (Hp+45) 40 ( E d_ 07/06 )
SINGLE LEAF APERTURE All the measures are approximated and are expressed in mm INSTALLATION FOR APERTURE UP TO 180º (It is necessary to be fitted into the wall) with C TYPE frames, 180º, 120º and 90º STANDARD DOORS LINEA CLASSIC Lfm+80 cierrapuertas (*) Lp= Lfm-82 175(*) Lfm-190(*) Lfm INSTALLATION FOR MAXIMUM CLEAR OPENING - Aperture minimum of 120º STANDARD DIMENSIONS NOMINAL WIDTH D Lfm+80 Lp=Lfm-82 800 890 990 1100 1200 430 475 525 580 630 D (**) Lfm (**) Maximum distance of separation between the Overall aperture and the closest wall near to the Hinges. If the door includes a panic bar, maximum clear opening will not be obtained INSTALLATION IN CORRIDOR - APERTURE UP TO 90º 1300 L= Lfm+25 680 Lfm+165 80 Lfm+80 40 Cierrapuertas(*) 20 B Lp=Lfm-82-20-B 40 Lfm B= differs depending on the handle or the installed bar (see accessories section). (example B= 100 for panic bar SR Series B= 70 for standard handle M0 and M1) (*) Measures for PUERTAS PADILLA standard handle Some handles and door closers can require the fitting into the wall. The installation ALWAYS has to be studied and approved by the Construction department ( E d_ 07/06 ) 41
DOUBLE LEAF All the measures are approximated and are expressed in mm INSTALLATION FOR APERTURE UP TO 180º (It is necessary to be fitted into the wall) L1+50 with C TYPE frames, 180º, 120º and 90º L2+100 STANDARD DOORS LINEA CLASSIC Lp=Lfm-80 175 (*) L1-215(*) Lfm INSTALLATION FOR MAXIMUM CLEAR OPENING - Aperture minimum of 120º STANDARD DIMENSIONS PRIMARY WIDTH, L1 D1 STANDARD DIMENSIONS NOMINAL WIDTH D 600 330 400 225 700 380 L1+50 L2+100 600 325 750 405 Lp = Lfm - 80 700 375 800 430 800 425 890 475 890 470 990 525 D1 (**) Lfm D2 (**) Lfm= L1+L2-15 990 520 (**) Maximum distance of separation between the Overall aperture and the closest wall near to the Hinges. If the door includes a panic bar, maximum clear opening will not be obtained INSTALLATION IN CORRIDOR - APERTURE UP TO 90º Lfm +160 L1+50 Lfm-80-40-(2xB) L2+100 40 20 B Lfm-80-20-B-L2 40 Lfm-80 B= differs depending on the handle or the installed bar (see accessories section). (example B= 100 for panic bar SR Series B= 70 for standard handle M0 and M1) Lfm (*) Measures for PUERTAS PADILLA standard handle Some handles and door closers can require the fitting into the wall. The installation ALWAYS has to be studied and approved by the Construction department ( E d_ 07/06 ) 42
"M" TYPE FRAME DIMENSIONS Multiuse, without fire resistant certification VERTICAL SECTION Lt= Width of external frame Ht= Heigt of external frame 1025 DIMENSIONS 1075 Hfm= Overall aperture Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L= Nominal width of the leaf Lp= Clear opening Lfm= Overall aperture 43 ( E d_ 07/06 )
"M" TYPE FRAME DIMENSIONS SINGLE LEAF without certification GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp External frame Lt x Ht L x H L x H (L-88) x (H-38) (L+88) x (H+50) STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Clear opening Lp x Hp External frame Lt x Ht 800 x 2050 890 x 2050 990 x 2050 1100 x 2050 1200 x 2050 1300 x 2050 800 x 2140 890 x 2140 990 x 2140 1100 x 2140 1200 x 2140 1300 x 2140 800 x 2050 890 x 2050 990 x 2050 1100 x 2050 1200 x 2050 1300 x 2050 800 x 2140 890 x 2140 990 x 2140 1100 x 2140 1200 x 2140 1300 x 2140 712 x 2012 802 x 2012 902 x 2012 1012 x 2012 1112 x 2012 1212 x 2012 712 x 2102 802 x 2102 902 x 2102 1012 x 2102 1112 x 2102 1212 x 2102 888 x 2100 978 x 2100 1078 x 2100 1188 x 2100 1288 x 2100 1388 x 2100 888 x 2190 978 x 2190 1078 x 2190 1188 x 2190 1288 x 2190 1388 x 2190 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Nominal L x H Lfm x Hfm (Lfm+88) x (Hfm+50) (Lfm-88) x (Hfm-38) Lfm x Hfm TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Clear opening Overall aperture Lfm x Hfm External Frame Lt x Ht Nominal leaf L x H Lp x Hp (Lp+88) x (Hp+38) (Lp+176) x (Hp+88) (Lp+88) x (Hp+38) 44 ( E d_ 07/06 )
"M" TYPE FRAME DIMENSIONS L1 = Primary Nominal width Lt= Width of external frame Multiuse, without fire resistant certification L2 = Secondary nominal width VERTICAL SECTION Ht= Heigt of external frame 1075 DIMENSIONS 1025 Hfm= Overall aperture Hp= Clear Opening H= Nominal height of the leaf Ht= Heigt of external frame Finished Floor HORIZONTAL SECTION OF A LEAF Lt= Width of external frame L1= Primary nominal width of the leaf L2= Secondary nominal width of the leaf Lpa= Primary clear opening Lp= Clear opening Lfm= Overall aperture 45 ( E d_ 07/06 )
"M" TYPE FRAME DIMENSIONS DOUBLE LEAF without certification GENERAL DIMENSION TABLE For these dimensions, a tolerance of ±3mm is applicable. Nominal leaf (L1+ L2) x H Overall aperture Lfm x Hfm (L1+L2+10) x H Primary clear opening Lpa L1-87 Clear opening Lp x Hp (L1+L2-76) x (H-38) External Frame Lt x Ht (L1+L2+100) x (H+50) DIMENSIONS STANDARD DIMENSIONS Nominal leaf Overall aperture Lfm x Hfm Primary clear opening Lpa Clear opening Lp x Hp External Frame Lt x Ht 600+590 (1190) x 2050 1200 x 2050 513 1014* x 2012 1290* x 2100 800+400 (1200) x 2050 1210 x 2050 713 1124 x 2012 1300 x 2100 650+640 (1290) x 2050 1300 x 2050 563 1214* x 2012 1390* x 2100 890+400 (1290) x 2050 1300 x 2050 803 1214 x 2012 1390 x 2100 700+690 (1390) x 2050 1400 x 2050 613 1314* x 2012 1490* x 2100 990+400 (1390) x 2050 1400 x 2050 903 1314 x 2012 1490 x 2100 750+740 (1490) x 2050 1500 x 2050 663 1414* x 2012 1590* x 2100 800+790 (1590) x 2050 1600 x 2050 713 1514* x 2012 1690* x 2100 890+880 (1770) x 2050 1780 x 2050 803 1694* x 2012 1870* x 2100 990+980 (1970) x 2050 1980 x 2050 903 1894* x 2012 2070* x 2100 600+590 (1190) x 2140 1200 x 2150 513 1014* x 2112 1290* x 2190 800+400 (1200) x 2140 1210 x 2150 713 1124 x 2112 1300 x 2190 650+640 (1290) x 2140 1300 x 2150 563 1214* x 2112 1390* x 2190 890+400 (1290) x 2140 1300 x 2150 803 1214 x 2112 1390 x 2190 700+690 (1390) x 2140 1400 x 2150 613 1314* x 2112 1490* x 2190 990+400 (1390) x 2140 1400 x 2150 903 1314 x 2112 1490 x 2190 750+740 (1490) x 2140 1500 x 2150 663 1414* x 2112 1590* x 2190 800+790 (1590) x 2140 1600 x 2150 803 1514* x 2112 1690* x 2190 890+880 (1770) x 2140 1780 x 2150 903 1694* x 2112 1870* x 2190 990+980 (1970) x 2140 1980 x 2150 903 1794* x 2112 2070* x 2190 TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the overall aperture dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture External Frame Lt x Ht Clear opening Lp x Hp Nominal leaf (L1+L2) x H Lfm x Hfm (Lfm+90) x (Hfm+50) (Lfm -86) x (Hfm-38) (Lfm-10) x H TAKE THE NOMINAL DIMENSION OF THE LEAF, once known the clear opening dimensions: To obtain different dimensions of the frame and nominal leaf, substitute the overall aperture (Lfm) and (Hfm) as follows: Overall aperture Clear opening Lfm x Hfm External Frame Lt x Ht Nominal leaf (L1+L2) x H Lp x Hp (Lp+86) x (Hp+38) (Lp+176) x (Hp+88) (Lp+76) x (Hp+38) 46 ( E d_ 07/06 )
FRAMES 47
MARCO MC3 MC3 FRAME FRAMES -Standard frame in all doors -Manufactured in steel of 1.2mm thick MC3 - MULTIUSE / EI2 60 MC3 - EI2 120 43 67,5 43 67,5 13 13 54 64 13 33 13 33 Available in 2 fixing ways WITH CLAMPS FIXED FOR SCREWS SCREWS NOT INCLUDED With fire certificate 48 ( E d_ 07/06 )
STANLESS STEEL MC3 FRAME STAINLESS STEEL MC3 FRAME FRAMES -Frame for doors Stainless steel line -Manufactured with fingerprint-resistant stainless steel of 1.2 thick. MC3 STAINLESS STEEL - EI2 120 42 72,5 13 64 13 32 Available in 2 fixing ways WITH CLAMPS FIXED FOR SCREWS SCREWS NOT INCLUDED With fire certificate 49 ( E d_ 07/06 )
MC3 FRAME SUPLEMENT MC6 SUPPLEMENT: these pieces, welded or screwed, help the MC3 frame to have a better depth or transform the frame into an embracing frame. FRAMES There are several options: MC6/AAND MC6/B OPTIONS, AT A WALL LEVEL SUPPLEMENT. They enlarge the wall making it deeper Frame with clamps MC6/A Screwed frames MC6/AA MINIMUM THICKNESS OF THE WALL Multiuse, EI260 EI290, EI2120 65 mm 75 mm Welded suplement * any request of MC6/D or MC6/DA inferior to this wall thickness dimension must be seek advice from the Technical Department. PROFILE MC6/A-B 30 d MC6/B MC6/BA 10 d EI260 EI290 EI2120 wall thickness -54 wall thickness -64 Screwed Supplement 33 MC6/C and MC6/D, EMBRACING WALL supplement It transforms the MC3 frame into Embracing frame. Welded frame MC6/C PROFILE MC6/C-D 30 d Welded suplement 10 d EI260 EI290 EI2120 wall thickness -31 wall thickness -41 Screwed frame 65 MC6/D MC6/DA MINIMUM THICKNESS OF THE WALL Screwed Supplement Multiuse, EI260 EI290, EI2120 65 mm 75 mm * any request of MC6/D or MC6/DA inferior to this wall thickness dimension must be seek advice from the Technical Department. The screwing supplements for its installation are sent dismounted by the client With fire certificate 50
REVER FRAME SUPPLEMENTS There are several options: FRAMES MC6/AAND MC6/B OPTIONS, AT A WALL LEVEL SUPPLEMENT. They enlarge the wall making it deeper. MINIMUM THICKNESS OF THE WALL Multiuse, EI260 65 mm Frame with clamps MC6/B Screwed frames MC6/BA EI290, EI2120 75 mm Screwed Supplement * any request of MC6/D or MC6/DA inferior to this wall thickness dimension must be seek advice from the Technical Department. MC6/A-B 30 d EI260 wall thickness -54 MC6/D OPTION, EMBRACING FRAME supplement 10 33 d EI290 EI2120 wall thickness -64 It transforms the REVER frame into an EMBRACING FRAME Frame with clamps Screwed frames MC6/D MC6/DA MINIMUM THICKNESS OF THE WALL Multiusos, EI260 65 mm EI290, EI2120 75 mm Screwed Supplement * any request of MC6/D or MC6/DA inferior to this wall thickness dimension must be seek advice from the Technical Department. MC6/D This option makes the frame higher from the hinges side (32mm) floor 30 EI260 d wall thickness -31 10 d EI290 EI2120 wall thickness -41 floor 65 The screwing supplements for its installation are sent dismounted by the client With fire certificate 51
MC3 PREFRAME MC 7 MC7 metallic preframe 1.5mm thick, for screwing. FRAMES a Multiuse EI260 EI290 EI2120 a 40 mm 50 mm 30 MC 8 MC8 metallic preframe 1.5mm with clamps a Multiuse EI260 EI290 EI2120 a 40 mm 50 mm 30 MC 19 MC19 Preframe with UNE certificate THERMAL KIT 51,5 32 Multiuse EI260 espesor 1 mm EI290 EI2120 2 mm 20 15 Along with this preframe the PADILLA thermal kit must be installed MC 20 / C Welded MC 20 / D Screwed -these preframes don t have fire door certificates. -these preframes are only available for using with MC3 EI2 120 frames ( E d_ 07/06 ) With fire certificate 52
"B" TYPE FRAME B TYPE FRAME FRAMES -Frame for installation in walls or corridors. -Manufactured in steel 1.5 mm thick. -It also can be manufactured in finger-proof stainless steel of 1.2mm thick. "B" TYPE - MULTIUSE / EI2 30 "B" TYPE STAINLESS STEEL - EI2 30 36,5 36,5 80 16 92 16 39 41 65 65 - The installation must be carried out with 9 screws located along the frame perimeter. INTUMESCENT SILICON CORD THE FOLLOWING ACCESSORIES ARE NOT PROVIDED: -SCREWS FOR THE INSTALLATION -CERAMIC FIBER BAND -INTUMESCENT SILICON BLANKET OF CERAMIC FIBER (5mm thick) With fire certificate 53 ( E d_ 07/06 )
TYPE "C" FRAME Type C frame FRAMES -Frame for installation in modular walls of plasterboard plates. -It is an embracing frame also suitable for other types of walls (without certification). -Manufactured in steel 1.5mm thick. -They have been manufactured in a Standard form for walls of 125mm and 150mm wide. -It can also be manufactured in other thick dimensions under prior order. TYPE "C" - MULTIUSE / EI2 120 9 43 Wall thickness + 35 Wall thickness + 4 5 80 It can be fixed with screws, by means of 22 holes located along the frame perimeter (11 holes for the hinges and 11 in the opposite side of the hinges). The screws and holes are hidden under the provided caps SCREWS FOR THE FRAME FIXING ARE PROVIDED With fire certificate 54 ( E d_ 07/06 )
"M" TYPE FRAME M TYPE FRAME - Embracing frame type in one piece. FRAMES - Frame available for installation in brick walls, modular walls of plasterboard plate, etc. -Manufactured in steel 1.5mm thick. -The frame doesn t have fire door certificate. -It can be manufactured in different thickness under prior order. -Minimum wall thickness=60mm -Maximum wall thickness=180mm "M" TYPE - MULTIUSE 6,5 60 Wall thickness + 1 41 88 It can be fixed with screws, by means of 22 holes located along the frame perimeter (11 holes for the hinges and 11 in the opposite side of the hinges). SCREWS FOR THE INSTALLATION ARE NOT PROVIDED 55 ( E d_ 07/06 )
CLAMP POSITION 56
THESE DIMENSIONS ARE SUBJECTED TO MODIFICATIONS MC3 FRAME POSITION MULTIUSE SINGLE LEAF MULTIUSE DOUBLE LEAF 150 L2 + 75 150 CLAMPS 315 315 315 315 Low nominal height H<1850 (H/2) - 40 Primary leaf side Secondary leaf side (H/2) - 40 270 270 270 40 40 270 L2 + 75 150 150 315 315 315 315 Normal nominal height 1850<H<2400 270 270 975 270 40 Primary leaf side Secondary leaf side 40 270 975 L2 + 75 150 150 315 315 315 315 815 815 815 815 High nominal height H>2400 975 Primary leaf side Secondary leaf side 975 270 270 270 40 40 270 57 ( E d_ 07/06 )
THESE DIMENSIONS ARE SUBJECTED TO MODIFICATIONS MC3 FRAME POSITION EI2 60 - SINGLE LEAF EI2 60 - DOUBLE LEAF L2 + 75 150 150 CLAMPS Low nominal height H<1850 315 315 (H/2) - 40 315 315 Primary leaf side Secondary leaf side (H/2) - 40 (H/2) + 110 (H/2) - 40 270 270 270 40 40 270 L2 + 75 150 150 315 315 315 315 Normal nominal height 1850<H<2400 975 1125 975 Primary leaf side Secondary leaf side 975 270 270 270 40 40 270 L2 + 75 150 150 315 315 315 315 815 815 815 815 High nominal height H>2400 975 Primary leaf side Secondary leaf side 975 1125 975 270 270 270 40 40 270 58 ( E d_ 07/06 )
THESE DIMENSIONS ARE SUBJECTED TO MODIFICATIONS MC3 FRAME POSITION Low nominal height H<1850 EI2 120 - SINGLE LEAF 315 315 EI2 120 - DOUBLE LEAF L2 + 75 150 150 315 315 CLAMPS (H/2) + 230 (H/2) - 40 270 270 (H/2) - 90 (H/2) + 230 (H/2) + 230 (H/2) - 40 270 40 Primary leaf side Secondary leaf side 40 270 (H/2) - 40 (H/2) + 230 Normal nominal height 1850<H<2400 L2 + 75 150 150 315 315 315 315 1400 975 270 270 925 1400 973 270 40 40 270 975 1400 High nominal height H>2400 L2 + 75 150 150 315 315 815 815 975 1400 975 1400 1400 Primary leaf side Secondary leaf side 315 315 815 815 1400 975 925 1400 Primary leaf side Secondary leaf side 270 270 270 40 40 270 59 ( E d_ 07/06 )
REVER FRAME POSITION THESE DIMENSIONS ARE SUBJECTED TO MODIFICATIONS CLAMPS MULTIUSE REVER REVER EI2 60 270 270 270 270 (H/2) - 50 (H/2) - 50 270 270 270 270 REVER EI2 120 270 270 (H/2) - 190 (H/2) - 250 (H/2) - 190 (H/2) - 250 270 270 60 ( E d_ 07/06 )
FINISHES 61
GAMACOLOR EI2 60 / EI2 90 / EI2 120 MULTIUSE 62
FINISHES Single leaf door -The three sides epoxy polymerized coated MC3 frame is manufactured in high resistant steel and is completed with a cold smoke seal. - Leaf of zinc-coated sheet, PVC laminated or painted in different finishes according to RAL color chart with 53mm thick for EI2 60 and MULTIUSE and 63mm for EI2 90 and EI2 120. -The doors of a nominal height over 2400mm are provided with and additional hinge. -Rock wool insulation EI2 60: 150kg/m3, 50 thickness Ei2 90: 150kg/m3, 60 thickness Ei2 120: 180kg/m3, 30 +30 thickness MULTIUSE: expansible polystyrene or aluminum bee nest design, 52 thickness. -Intumescent seal in EI2 60 frame: 20 x 2 mm, E12 120: 30 x 2. - CEN approved EI hinges. - CEN approved lock. -Fire-resistant DIN handle with anti-coupling, completed with a polyamide fire-proof steel core. For multiuse doors, the handle is made out of plastic. -Anti-crowbar device: E12 60, one device per leaf; EI 2 90 and EI2 120, two devices per leaf. Multiuse doors are not provided with anti-crowbar device. - The frame is provided with 6 dead- end clamps for EI2 60, 8 for EI2 90 and EI 120 and 4 for multiuse doors. - Closer selector EI2 120, optional in EI2 60 -Separators for the installation. -Metallic identification label with E12 certification. -Instructions for fitting and maintenance -Door leaf weight EI2 60: 25kg/m2 EI2 90: 28.5kg/m2 EI2 120: 30kg/m2 Multiuse: 18kg/m2 GAMACOLOR Left hand opening (SX) Right hand opening (DX) Anti-crowbar device Lock Handle Intumescent seal 63 ( E d_ 07/06 )
FINISHES Double leaf door -The three sides epoxy polymerized coated MC3 frame is manufactured high resistant steel and is completed with a cold smoke seal. - Leaf of zinc-coated sheet, PVC laminated or painted in different finishes according to RAL color chart with 53mm thick for EI2 60 and MULTIUSE and 63mm for EI2 90 and EI2 120. -The doors of a nominal height over 2400mm are provided with and additional hinge. -Rock wool insulation GAMACOLOR EI2 60: 150kg/m3, 50 thickness Ei2 90: 150kg/m3, 60 thickness Ei2 120: 180kg/m3, 30 +30 thickness MULTIUSE: expansible polystyrene or aluminum bee nest design, 52mm thickness. -Secondary leaf seal EI 60: 33 x 2mm, EI2 120: 43 x 2mm. - CEN approved EI hinges. - CEN approved lock. -Fire-resistant DIN handle with anti-coupling, completed with a polyamide fire-proof steel core. For multiuse doors, the handle is made out of plastic. -Anti-crowbar device: E12 60, one device per leaf; EI 2 90 and EI2 120, two devices per leaf. Multiuse doors are not provided with anti-crowbar device. - The frame is provided with 11 dead- end clamps for EI2 60, 13 for EI2 90 and EI 120 and 11 for multiuse doors. - Closer selector EI2 120, optional in EI2 60 -Separators for the installation. -Instructions for fitting and maintenance -Door leaf weight EI2 60: 25kg/m2 EI2 90: 28.5kg/m2 EI2 120: 30kg/m2 Multiuse: 18kg/m2 Left hand opening (SX) Right hand opening (DX) Anti-crowbar device Lock Handle Intumescent seal 64 ( E d_ 07/06 )
FINISHES EI260, EI290, EI2 120, Multiuse Between the frame and the leaf a different tonality can be presented, this may result from the differences of the finishes and the process of paint coat. Every PVC colour for the door leaf, can be only provided with its corresponding RAL colour for the frame, according to the enclosed chart. It only can be manufactured with these combinations and the doors cannot be provided with different colour combinations between the frame and the leaf. The doors with different colours for each side of the leaf are not provided. GAMACOLOR STANDARD EPOXY-POLYESTER GOFFERED RAL CHART FRAME-LEAF COLOUR CORRESPONDENCE. Maximum dimensions per leaf: L (400-1300) and H (1250-2550) RAL 1013 RAL 9001 RAL 5010 RAL 6034 RAL 7024 RAL 7035 RAL 7038 RAL 9003 RAL 9002 RAL 9010 RAL 9018 RAL 1003 RAL 3000 RAL 9011 RAL 9007 LISO RAL 6005 - Extra charge depending on the colour. RAL 6000 RAL 5024 RAL 8011 PVC RANGE. RAL textured finish frame MAXIMUM DIMENSIONS PER LEAF: -EI2 60 L (400-1100) y H (1250-2950) -EI2 90 L (400-1090) y H (1250-2900) -EI2 120 L (400-1090) y H (1250-2900) ROBLE ROBLE NUEVO TANGANIKA HAYA SAPELLY DL1 DL21C DL65 DL76 DL88 PINO NOGAL CEREZO WENGUE DL10 Ral 8017 textured finish frame. DL64 DL78SME DL36CE 65 The colour reproduced in the brochure may be slightly inaccurate due to printing ( Ereasons. d_ 07/06 It is ) recommended that a RAL colour chart is used when specifying colours.
FINISHES EI260, EI290, EI2 120, Multiuse PVC RANGE. Maximum dimensions per leaf: L (400-1090) y H (1250-2950) GAMACOLOR RED DARK GREEN GRAPHITE BLACK R8SMA V8SME N3SMA LIGHT BLUE GRAPHITE GREASE IVORY B1 N12SM A17SMA MAROON BLUE GREEN TURQUOISE R24SMAM B35SMA V36SMA CREAM YELLOW WHITE A56SMA G11SM A47SMA ALUMINIUM AND STAINLESS STEEL COLOR Maximum dimensions per leaf: L (400-1090) y H (1250-2950) ALUMINIUM GREASE ALUMINIUM STAINLESS STEEL F23SMA F16 PPS F12PPS Frame finished in RAL plain 9007. 66 The colour reproduced in the brochure may be slightly inaccurate due to printing ( reasons. E d_ 07/06 It is ) recommended that a RAL colour chart is used when specifying colours.
SPECIAL FINISHES EI260, EI290, EI2 120, Multiuse The innova system makes possible a digital printing in multiuse and fire doors. In this way, we give an answer to: - Special requirements in decoration projects. - New advertising support in public spaces Shopping centers, cinema, garage, theatre, etc. For more information, seek advice from Technical Department GAMACOLOR IMPORTANT NOTE: To print a door with quality the image must have a minimum of half size of the real size and a minimum resolution of 300dpi. SPECIAL DOORS FOR HOSPITAL AND FOOD HANDLING Puertas Padilla offers a product specially designed for sanitary installations. It is an ideal product to be installed in Hospitals and Handling food Centers. It is provided with a non-toxic self-extinguishing finish in accordance with the norm D.M.21.3.73/2.6.82 and 25.4.93 prevent the adherence of bacteria and allow an easy cleaning of the door. Special equipments: The Hospital door is manufactured with a stainless steel lockset front. MC3 frame-mc6 optional Manufactured with hinges and with stainless steel hinges CEN approved (optional). To guarantee the best health conditions the handle is made of stainless steel or aluminium. 67 ( E d_ 07/06 )
SPECIAL FINISHES EI260, EI2 120, Multiuse GAMACOLOR INTENSIVE OR HEAVY USE DOORS: sheet 1mm thickness -In order to improve the mechanical conditions, it is necessary a higher thickness of the sheet, at least 1mm. In case of requirement of accessories, it is extremely important the fixing and the installation of the accessories able to support the mentioned level of use (see Technical Department). -In double leaf doors is also recommended the installation of CEN level 5 door closers (according to EN 1191) that make possible an appropriate door performance in the course of time.. 68 ( E d_ 07/06 )
STAINLESS STEEL FINISHES EI2 120 69
FINISHES EI2 120 Single leaf door -MC3 high resistant stainless steel three sides frame with cold smoke seal. -Nominal height doors over 2400mm are manufactured with an additional hinge. -Stainless steel 6/10 leaf (AISI 304) or satin finish, 63mm thick. -Rock wool insulation with a density of 180kg/m3 and 30 + 30 thickness. -Intumescent seal in 30 x 2 frame. -CEN approved hinges -CEN certification stainless steel lockset front. -Secondary leaf provided with CR4. -Steel handle with Stainless steel cover. -4 anti-crowbar devices (2 per leaf). -The frame is provided with 13 dead-end clamps up to a maximum dimension of 2400mm of nominal height. Over this dimensions the frame is provided with 15 dead-end clamps. -Closer selector. -Separators for its installation. -Instructions for fitting and maintenance. -Leaf weight of 30kg/m2 LINEA STAINLESS INOX STEEL Right hand opening (DX) Left hand opening (SX) Double leaf doors -MC3 high resistant stainless steel three sides frame with cold smoke seal. -Nominal height doors over 2400mm are manufactured with an additional hinge. -Stainless steel 6/10 leaf (AISI 304) or satin finish, 63mm thick. -Rock wool insulation with a density of 180kg/m3 and 30 + 30 thickness. -Intumescent seal in 30 x 2 frame. -CEN approved hinges -CEN certification stainless steel lockset front. -Secondary leaf provided with CR4. -Steel handle with Stainless steel cover. -4 anti-crowbar devices (2 per leaf). -The frame is provided with 13 dead-end clamps up to a maximum dimension of 2400mm of nominal height. Over this dimensions the frame is provided with 15 dead-end clamps. -Closer selector. -Separators for its installation. -Instructions for fitting and maintenance. -Leaf weight of 30kg/m2 Left hand opening (SX) Right hand opening (DX) BM0. Stainless steel hinge CE certificated lock Stainless steel handle Intumescent seal Adjustable stainless steel hinge 70 ( E d_ 07/06 )
ACOUSTIC FINISHES UNE EN ISO 140-3/A1 CERTIFICATE UNE EN ISO 717-1 CERTIFICATE 38 db - 34 db EI2 60 43 db - 35 db EI2 120 71
FINISHES Single leaf doors 38 db - 43 db ACOUSTIC ACOUSTIC KA 5 acoustic kit High resistant steel MC3 three sides frame with cold smoke seal and with a polymerized coated epoxy. -Leaf with a Skinpass galvanized steel sheet, 7035 RAL COLOUR, EI2 60: 53 mm of thickness; EI 120: 63mm of thickness. -The doors with a nominal height over 2400mm are manufactured with an additional hinge. -Rock wool insulation EI2 60: 150kg/m3, 50 of thickness EI2 120: 180/M3, 30 + 30 thickness -Intumescent seal in EI2 60 frame: 20 x 2 mm, EI2 120: 30 x 2 mm. -CEN EI certificated hinge -CEN EI certificated lock -Fire-resistant DIN handle completed with a polyamide fire-proof steel core.. -Anti-crowbar device: E12 60, one device per leaf; EI 2 90 and EI2 120, two devices per leaf. - The frame is provided with dead- end clamps -Separators for the installation. -Metallic identification label with E12 certification. -Instructions for fitting and maintenance. -Optional: Acoustic kits: KA 4 OR KA 7 1 3 2 5 4 Acoustic kits: The acoustic seal kit gives an acoustic isolation to the door 1 JF1 2 JF4 3 JAI1 4 PP1 4 PP2 5 GS1 ACOUSTIC ISOLATION IN db EI2 60 EI2 120 sin KIT 19,00 20,00 KA 4 X X X X 37,00 41,00 KA 5 X X X X 36,00 40,00 KA 7 X X X X 38,00 42,00 72 ( E d_ 07/06 )
FINISHES Double leaf doors 38 db - 43 db ACOUSTIC ACOUSTIC -KA 5 acoustic kit - High resistant steel MC3 three sides frame with cold smoke seal and with a polymerized coated epoxy. -Leaf with a Skin pass galvanized steel sheet, prepainted 7035 RAL COLOUR, EI2 60: 53 mm of thickness; EI 120: 63mm of thickness. High resistant steel MC3 three sides frame with cold smoke seal and with a polymerized coated epoxy. -Leaf with a Skinpass galvanized steel sheet, 7035 RAL COLOUR, EI2 60: 53 mm of thickness; EI 120: 63mm of thickness. -The doors with a nominal height over 2400mm are manufactured with an additional hinge. -Rock wool insulation EI2 60: 150kg/m3, 50 of thickness EI2 120: 180/M3, 30 + 30 thickness -Intumescent seal in EI2 60 frame: 20 x 2 mm, EI2 120: 30 x 2 mm. -CEN EI certificated hinge -CEN EI certificated lock and cylinder patent key -Secondary leaf provided with latch or CR4 -Fire-resistant DIN handle with anti-coupling, completed with a polyamide fire-proof steel core.. -Anti-crowbar device: E12 60, one device per leaf; EI 2 90 and EI2 120, two devices per leaf. - The frame is provided with dead- end clamps -Closer selector in EI2 120, optional in EI2 60 -Separators for the installation. -Instructions for fitting and maintenance. -Optional: Acoustic kits: KA 4 OR KA 7 1 3 2 5 4 Acoustic kits: The acoustic seal kit gives an acoustic isolation to the door 1 JF1 2 JF4 3 JAI1 JAI2 4 PP1 4 PP2 5 GS1 ACOUSTIC ISOLATION IN db EI2 60 EI2 120 sin KIT 19,00 20,00 KA 4 X X X X X 33,00 34,00 KA 5 X X X X X 35,00 35,00 KA 7 X X X X X 35,00 35,00 73 ( E d_ 07/06 )
HARDWARE 74
HARDWARE BISAGRAS B01, DIN HINGE WITH BEARING -This hinge is assembled with a hinge screw, a gasket and a bearing that make possible the movement of the leaf. - In REVERSIBLE doors the gasket can be replaced by another bearing to ensure the reversible feature. - For RIGHT opening hand, this hinge is locates in the inferior part of the frame. For LEFT opening hand it is located in the upper part. - With this hinge it is possible to increase the leaf height 1.25mm or 2.500, by inserting 1 or 2 extra gaskets respectively (See Instructions. Adjustment of the leaf height ). -Hinge manufactured according to DIN 18272 -CE approved according to the norm EN 1935. BISAGRAS HARDWARE BEARING GASKET HINGE SCREW WITHOUT SPRING STEEL 3 mm THICKNESS 75 ( E d_ 07/06 )
HARDWARE BISAGRAS B02, DIN HINGE WITH AUTOMATIC CLOSER -This hinge is assembled with a hinge screw provided with a spring and a tension retainer that help the closing of the frame. - For RIGHT opening hand, this hinge is located in the upper part of the frame. For LEFT opening hand is in the inferior part. - Those doors with a third hinge, this one is always a hinge with automatic closer. -Hinge manufactured according to DIN 18272. BISAGRAS HARDWARE HINGE SCREW WITH AN AUTOMATIC CLOSER SPRING RETAINER FOR FIXING THE TENSION OF THE AUTOMATIC CLOSER SPRING STEEL 3 mm THICKNESS 76 ( E d_ 07/06 )
HARDWARE ISAGRA INOX REGULABLE B04, STAINLESS STEEL SPECIAL HINGE HARDWARE BISAGRAS This hinge includes, in its fitted frame, a regulation system of the leaf with three positions: -Height -Support distance of the leaf over the frame. - Lateral looseness between the leaf and the frame (it makes possible to adjust the leaf nodding). -It includes a bearing system that makes easier the movement of the leaf. -CE approved according to EN 1935-14. Stainless steel special hinge Hinge regulation system integrated in the frame 77 ( E d_ 07/06 )
HARDWARE BISAGRA INOX B03, STAINLESS STEEL HINGE BISAGRAS HARDWARE -This standard hinge is installed in the STAINLESS STEEL range doors. -To install different kind of frame of the Stainless steel range, seek advice for the Technical Department. -It is integrated with a bearing system that makes easier the movement of the leaf. -CE approved according to EN 1935-14. 78 ( E d_ 07/06 )
HARDWARE BISAGRA MULTIUSOS B05, MULTIUSE HINGE BISAGRAS HARDWARE -This hinge is installed in multiuse leaf doors 79 ( E d_ 07/06 )
HARDWARE BISAGRA MULTIUSOS BM0, STAINLESS STEEL HINGE HARDWARE BISAGRAS -Hinge of stainless steel finish 80 ( E d_ 07/06 )
HANDLES 81
HANDLES HANDLES: Opening door device, it can also be combined with a panic bar which activate the lock located in the leaf. It is installed in all primary doors and single leaf door. EI2 DOORS The handle provided as a standard is the M1 model black colour. A different kind of handle included in this technical catalogue can be provided. M1: Standard fire door handle -According to DIN 18255. -Steel core -Handle diameter: 20mm or 23mm Anti-coupling fire door handle according to DIN, made of fire-proof polyamide with steel core. DIFFERENT FINISHES- ONLY IN EI2 It can be provided in stainless steel or aluminium F1 finish. aluminium M1 : Standard fire door handle HANDLE MULTIUSE DOORS For multiuse doors, a M0 handle range in black colour shall be provided. F1 finish. Aluminium Stainless steel satin Handle M1 Handle M1 Handle M0 82
HANDLE HANDLE M0 M1 Multiuse door handle for multiuse doors incorporating patent cylinder lock fitting. Handle operation from both sides. M2 Evacuación Standard door handle incorporating patent cylinder lock fitting. Handle operation from both sides. M3 Condenable por cilindro Antipanic handle (to push) with condenable handle and operation with key on both sides. Standard handle, operation from both sides. Without lock feature M4 M6 Evacuation Cover plate on both sides. No door handle operation KIT GARAGE Operation from one side handle. Fix knob, incorporates key and it operates from both sides. M7 M8 Fix knob, blind plate. Operation by key from both sides Fix knob. Operation by key from both sides. M10 M11 Handle for WATER lock Handle for ISABEL II lock M12 Evacuation Fix knob Rosette model. Operation by key on both sides, black colour. 83
HARDWARE DOOR HANDLE FITTING INSTRUCTIONS HANDLE 1. Select the parts to be fitted according to the EI range of the door; the parts for 60/120 are common for both thickness. 5. Insert the piece 4 in the inferior in the square hole (half cylinder upwards). 2.The parts with rectangle shape have to be fitted on the hinge side those of half cylinder shape go on the opposite side of the hinges. 6.Clamp the handles to the handle linkage shafts with the two grub screws located in the handles. 3. Locate the square shape piece 1 upwards, right through the superior cylinder lock and fit the piece 2 with the piece 1 (half cylinder upwards). 7.Once they have been fitted, the plastic cover will be placed. 4. Insert the piece 3 in the inferior square hole with the rectangle shape upwards. 84
LOCKS 85
LOCKS LOCKS: device that make possible to keep the door in a closed position Single leaf A Active leaf of double leaf door P Passive leaf of a double leaf door HARDWARE For those doors with fitted panic bar, the lock shall not be installed FOR SINGLE OR ACTIVE DOOR A CR1 STANDARD LOCK CF 50 MODEL, CE EN 12209 -Reversible lock -Condenable in both sides -Square bar steel, 9mm -Entrance 65mm CR2 PADILLA EMERGENCY LOCK -Din lock -Reversible -Adjustable latch for easy opening -Anti-lock system (It is not possible to lock the evacuation paths, according to NBE CPI-91) -Square bar steel, 9mm -Entrance 65mm CR3 SPECIAL PANIC LOCK -CE Marked -Reversible -Adjustable latch for easy opening -Anti-panic function with condenable by key exterior handle -Square bar steel 9 mm -Entrance 65mm CR 7 CR7 BARREL LOCK -Barrel lock -Opening device (PUSH-PULL) -Not available for certified doors 86
LOCKS PASSIVE LEAF LOCK Single leaf P A Active leaf of double leaf door P Passive leaf of a double leaf door HARDWARE CR 4 MANUAL FLASH BOLT -Passive leaf closer -Automatic device with 2 closing points -Manual opening -CE Marked CR 5 CR5 CONTRA-LOCK (anti-panic) -Anti-panic closing for passive leaf -Automatic device with 2 closing points -Opening through panic bar -CE Marked Screwed rods for CR 4 y CR 5: With both locks the superior and inferior passive leaf closing can be performance by the screwed rods. PT 1 PT1 LATCH PT1 -Closing for passive leaf -Superior and inferior latch with manual operation Only available for multiuse double leaf doors As an optional choice for passive leaf doors, we provide a floor limiter for the inferior bar of the secondary leaf TP1 Floor limiter for secondary leaf 87
HARDWARE ELECTROMECHANICAL LOCK ELECTROMECHANICAL LOCK: are locks which opening is controlled by a switch or control device. This device supplies 12Vdc to the lock allowing it to open. These locks are for single or active leaf of double leaf doors. There are two types: HARDWARE CR1E; electromechanical fireproof standard lock CR3E; electromechanical fireproof lock for panic bar Operation information a) As long as the inductor is properly feed, with adequate tension and polarity, it can be open by using the handle of any of the side door; even if the door is locked. b) Without tension; -CR1E model it will never open if the door is locked (with the key). -C33E model, it won t open from the hinge side if the door is locked (with the key). From the panic bar side (opposite to the hinges) this lock can be open at any time. NOTE: There will be only electrical tension, when the electric power supply is active. DOOR LOCKED DOOR UNLOCK CR1E Both handles open CR1E Both handles open with 12Vdc CR3E Handle opens-bar opens CR3E Handle opens-bar opens CR1E None of handles open CR1E Both handles open Without 12Vdc CR3E Handle doesn t open-bar opens CR3E Handle opens-bar opens 88
HARDWARE ROLLAWAY WIRED TUBE The rollaway wired tube, go through the leaf from the opposite side of the lock and is connected by an anti-vandalism cable with the frame. The above mentioned cable has been designed to guarantee the continuous transference of the cable between the door and frame. HARDWARE PS-1 (Anti-vandalism rollaway cable) -Anti-vandalism rollaway cable, it remains hidden when the leaf is closed. -It accepts cables up to 7mm diameter. -Tube and cover plate made of stainless steel. -It is possible to build in the leaf of the door Pictures of the finishing of the anti-vandalism rollaway cable. 89
ACCESSORIES NOVACLASS CLASSIC GAMACOLOR ACÚSTICA INOX ACCESORIOS
PANIC BARS 91
ACCESSORIES PANIC BARS: The anti-panic device is a device for opening doors located in Emergency exits of public places where a panic situation can occur. It opens outwards PANIC BARS TYPES Puertas Padilla S.L. offers 5 different types of Anti-panic devices PANIC BAR -Panic bar SR range: it works by activating the CR3 standard lock that is inserted in the leaf interior. Panic bar SR range -Panic bar T range: the bar itself has a door handle system that works as a lock, the lock is not necessary in the leaf. -Touch bar: it works by activating the lock inserted in the leaf, as the case of the first type, but its dimensions are smaller making possible a bigger space in 90 apertures. Panic bar T range -Techno bar: it works by activating the CR3 standard lock that is inserted in the leaf interior. -Techno plus bar: it works by activating the CR3 standard lock that is inserted in the leaf interior. Touch bar ACCESSORIES Techno bar Techno plus bar 92
ACCESSORIES SR TYPE BAR (TO INLAY) SR RANGE BAR PANIC BAR GENERAL CHARACTERISTICS -Standard colours: red and black -CE marked -Manufactured for single and double door -1 closing point -Reversible -Exterior activation in different finishes CERTIFICATION Classified according to European certification EN 1125 Satin Stainless steel chrome plated Brass tonality 39 3 7 6 1 1 3 2 2 A 208 AVAILABLE OPTIONS 98 A + Single leaf 971 SR A Active leaf of double leaf door P Passive leaf of a double leaf door Exterior opening option. Through the handle 970 SR Single leaf door Active leaf of double leaf door passive leaf of double leaf door + + + 975 SR 972 SR 973 SR Exterior opening option. Through handle or key Without the exterior opening option, with blind plate Exterior opening option through key + 974 SR Exterior opening option through key and fixed knob P 970 SRA Bar for passive leaf in double leaf doors. Without the possibility of exterior opening activation. This bar can be installed if the door has been installed with a CR-5 lock 93
ACCESSORIES T BAR T TYPE BAR (TO OVERLAY) GENERAL CHARACTERISTICS PANIC BAR -Standard colours: black and red -CE Marked -Available for single and double doors. -From 1 to 3 closing points. -Reversible -Exterior activation in different kind of finishes. CERTIFICATION Classified according to the European certification Satin Stainless steel chrome plated Brass tonality EN 1125 39 3 7 6 1 1 3 2 2 A 30 208 AVAILABLE OPTIONS 98 Single leaf A Active leaf of double leaf door P Passive leaf of a double leaf door A + 910 T Exterior opening option. Through the handle 913 T Panic bar for Single and active Leaf of double Door. + + + 912 T 914 T 915 T Exterior opening option. Through handle or key Without the exterior opening option, with blind plate Exterior opening option through key + 911 T Exterior opening option through key and fixed knob + 953 Closing points bar for primary leaf, with exterior activation, through handle P 3 points bar for single leaf door + 952 Closing points bar for primary leaf, with exterior activation. Through handle and key 931 T Closing points bar for passive leaf of double leaf doors + 950 Closing points bar for primary leaf, without exterior activation, with blind plate 94
ACCESSORIES TOUCH PANIC BAR TOUCH BAR ( TO INLAY) INSTALLATION NOT PROVIDED PANIC BAR GENERAL CHARACTERISTICS -Standard colours: red and black -CE Marked -Available for single and double doors. -Touch bar: 1 closing point -Reversible -Exterior activation in different kind of finishes CERTIFICATION Certification according to the European norm EN 1125 Aluminium satin - stainless Brass tonality 3 7 6 1 1 4 2 2 B AVAILABLE OPTIONS Single leaf A Active leaf of double leaf door P Passive leaf of a double leaf door A + 59710-1 Exterior opening option. Through the handle 59710 Panic bar for Single and active Leaf of double Door. + + + 59710-5 59710-2 59710-3 Exterior opening option. Through handle or key Without the exterior opening option, with blind plate Exterior opening option through key + 59710-4 Exterior opening option through key and fixed knob P 59710-6 Bar for passive leaf in double leaf doors. Without exterior activation 95
ACCESSORIES TECHNO BAR PANIC BAR TECHNO BAR GENERAL CHARACTERISTICS -Standard colour: black and aluminium tube -CE Marked -For single and double leaf doors - For secondary leaf of double leaf door with hidden bars for inferior and superior closer. - Reversible CERTIFICATION -Certificated according to norm UNI EN 1125 Steel core box covered with resistant plastic material in black colour, aluminium anodize tube in oval shape 3 6 6 1 1 3 2 1 A DIMENSIONS- MARKED 96
ACCESSORIES TECHNO PLUS BAR PANIC BAR GENERAL CHARACTERISTICS -Standard colours: black and aluminium tube -CE marked -For single and double leaf doors. -For secondary leaf of the doors is provided with hidden bars for superior and inferior closer. -Reversible CERTIFICATION -Certificated according to norm UNI EN 1125 3 6 6 1 1 3 2 2 B 97
VISION PANEL AND GLASS 98
ACCESSORIES VISION PANEL AND GLASS VISION PANEL AND GLASS VISION PANEL: accessory that makes possible to see the through the other side of the room, it can be fitted in places where there is a frequent transit of people and the door must be closed due to safety reasons. TYPES OF VISION PANELS AND GLASS There are two different types of vision panel; rectangular and circular. Circular vision panel ADDECUATE MAINTENANCE OF THE GLASS -EI glass have been manufactured for an indoor use, as they become opaque if the glass is exposed to atmospheric agents or direct sunlight. -The glass should be washed with lukewarm water, a soft fiber cloth and a compatible cleaner applied with a spray. Let rinse and wipe away with a soft cloth. -Do not use any kind of acid, alkaline, chemical substances, solvent or its steam, abrasives or sharpened objects. It should never be used dirty clothes for cleaning up the glass. Rectangular vision panel 99
ACCESSORIES STRATIFIED GLASS FOR MULTIUSE DOORS STRATIFIED GLASS FOR MULTIUSE DOORS VISION PANEL AND GLASS Dimensions Cod. 300 X 400 600 X 400 280 Ø V2 V3 V4 100
ACCESSORIES VISION PANEL EI 60 AND EI 120 VISION PANEL AND GLASS EI 60 VISION PANEL FOR FIRE DOORS EI 120 VISION PANEL FOR FIRE DOORS Dimensions Cod. Dimensions Cod. 300 X 400 V14 300 X 400 V21 600 X 400 V16 600 X 400 V23 280 Ø V18C 280 Ø V25C GLASS FOR EI2 60 GLASS FOR EI2 120 Fire- proof 101
ACCESSORIES VISION PANEL LOCALIZATION VISION PANEL AND GLASS B= Min. 300 = = B= Min. 300 = = C=1550 C=1785 VERTICAL LOCATION As long as the leaf height is lower than 2050, a circular hole will be performed with its center in C measure point. In those doors which dimensions are smaller, the minimum B dimension will be respected. HORIZONTAL LOCATION On the side part it shall be centered, respecting always the A minimum measure point as indicated in previous pages. 102
A A ACCESSORIES STEPS TO FIT THE GLASS VISION PANEL FITTING 1.- Mark out the door leaf with the minimum required dimensions indicated in previous pages. 5.- Turn the door leaf over to provide access from the other side and place the vision panel into the aperture. VISION PANEL AND GLASS 2.- Drill through the door leaf and then cut the hole with a jigsaw fitted with a fine toothed blade, pay special attention in order to prevent any delamination of the door leaf. 3.- Locate as many retaining clips as screws have the snap fastener ( not less than 4-6) according to the inferior figure. So it can match up with the location where the screws are going to be placed. 4.- Locate the vision panel in the hole with the supplied self-reaming tapping screws. 6.-Locate the ceramic fiber insulation blanket onto the edge of the vision panel or the peep hole seal if is circular. 7.- Fit the glass by locating the Intumescent seal on the retaining clips until the ideal adjustment is reached. 8.-Locate the second vision frame in the proper position and screw it on. 9.- Cut out the remaining Ceramic blanket. In case of rectangular peep hole VISION PANEL OR PEEP HOLE FITTING: HORIZONTAL SECTION Rectangular Ceramic blanket CIrcular untumescent seal 2.5 2.5 Cristal Agujero = cristal + 5 VISION PANEL OR PEEP HOLE FITTING: VERTICAL SECTION B 2.5 2.5 Cristal B 2.5 C Cristal C 2.5 103
CYLINDERS 104
ACCESSORIES CYLINDERS CYLINDERS: device that makes possible to block the lock so the door cannot be open by activating the handle. There are locks; such as CR3 lock that, by using the cylinder, it can only be locked from outside and with the bar is possible to open the door. CYLINDERS The doors are provided with the C1 lock as a Standard lock C 1 Patent cylinder (one key included) C 2 Metal half cylinder 10 35 C 3 C 3 75mm metallic cylinder (three keys included) (EI2 60/ Multiuse) 35 10 35 C 4 C4 85mm metallic cylinder (three keys included) (EI2 120) 30/40 10 35 C4/2 85mm metallic cylinder (three keys included) (EI2 120) C 6 75mm 2 sides mastered keyed cylinder (three keys and one mastered key per set) (EI2 60/Multiuse) C 6 C6 / 2 85mm 2 sides mastered keyed cylinder (EI2 120) (three keys and one mastered key per set) 30/40 10 35 C 7 74mm Mastered keyed thumb turn cylinder (one mastered key and three keys included) (EI2 60/Multiuse) C 7 30/40 10 35 C7/2 85mm Mastered keyed thumb turn cylinder (one mastered key and three keys included) (EI2 120) 105
SELECTORS 106
ACCESSORIES OPEN SELECTOR Open selector: device that makes possible the opening of the primary leaf when the secondary leaf bar is activated Only available for double leaf passive doors with panic bar SELECTORS SA Double leaf open selector OPEN SELECTOR FITTING INSTRUCTIONS 1. It is fitted in the upper part of the passive leaf, in the opposite side of the hinges. 2. Screw on the main frame with 4 self- reaming tapping screws (M5). Make sure that the fixing screws are firmly tightened. 3. Use the regulation screw provided to regulate the open selector angle and ensure that the selector makes contact with the primary leaf Horizontal Section Regulation screw of the opening angle Self-reaming tapping screws Main frame 107
ACCESSORIES OPEN SELECTOR CLOSE SELECTOR: Device that coordinates the double leaf doors closing to avoid that the primary leaf closes before the secondary one and the door remains opened SELECTORS -For active leaf doors with a width over 1000mm this system is not advised. In this case a hydraulic closer selector must be installed Horizontal section SC Standard closer selector SR 90 Closer selector floor SCE Extra-flat close selector SCP Flat closer selector 108
ACCESSORIES STANDARD CLOSE SELECTOR STANDARD Close Selector Close selector to be integrated in the MC3 frame, it will remain hidden once the leaves are closed. Reversible Cylindrical bar, 12mm thickness. It is provided with a spring to absorb the shock in the retention of the primary leaf. It is fitted on the frame once it has been installed in its box SELECTOR csc close selector installation box We have available as an option, a cap to cover the frame holes where the selector is installed TSC PVC plate to cover the holes of the predisposition of the close selector CLOSE SELECTOR FITTING INSTRUCTIONS 1. Before fitting the door in the wall, screw on firmly the box to the frame using the screws (A). 2. Once the door is fitted and regulated, insert the selector in the box making sure that it goes towards the primary leaf. Fix it with the screws (B) that are provided in the box. 3. Adjust the selector by turning the regulation screw located in the internal part (and Allen key shall be required). Ensure the selector makes contact with the superior corner of the primary leaf. 4. Check if the device works properly. To be used only with the provided screws Regulation screw (C) A A B 109
ACCESSORIES FLOOR CLOSE SELECTOR FLOOR Close Selector This floor close selector has been manufactured to be placed on the frame, from the hinges side, in order to be located precisely over the leaves. It consists of 3 parts: bar, passive leaf limiter, active leaf limiter. SELECTORS Bar Active leaf limitator Passive leaf limitator Reversible CE marked Cylindrical bar of 18mm thickness provided with a spring to absorb the retention shock of the primary leaf. It is possible to be installed in MC3 and C type frames: It cannot be installed in B type frame. 110
ACCESSORIES EXTRA-FLAT CLOSE SELECTOR Extra-flat Close Selector Close selector to be placed under the frame lintel. Reversible CE marked Extra-flat bar of 4mm thickness SELECTORS Extra-flat selector This floor close selector has been specially manufactured to be placed on double leaf B and C Type frames. It is also possible to install it in MC3 frames if: -The frame is provided with an MC6 embracing frame -The wall covers up to the lower part of the lintel - It is used any kind of square for its fixation on the lintel level. Fixation square MC3 frame Screws Close selector The installation of this selector can reduce 12mm from the vertical clear opening under the part covered by this 111
ACCESSORIES FLAT SELECTOR Flat selector -Flat selector to overlay on the frame lintel -Reversible by changing the position of the adjustement screw -Flat rod 10mm thickness SELECTORS Flat Selector It is designed for its fitting on double leaf B and C Type frames. It is also possible to be installed in MC3 frames if: -The frame has a MC6 embracing frame. - The wall covers until the lower part of the lintel. - It is used any kind of square for its fixation up to the lintel level. The installation of this selector can reduce from 12 to 20 mm from the vertical clear opening under the part covered by this. 112
ELECTROMAGNETS 113
ELECTROMAGNETS ELECTROMAGNETS: System that locks the door in open position, in the event of a fire, the door electromagnet is turned off by pushing the electromagnet or by the fire alarm system. ELECTROIMANES Electromagnets are installed in public or crowed places where it should be a previous barrier against fire. E 2 Electromagnet with unlocking system Power supply: 24Vdc Absorbed power: 70mA Tractive effort :> 55kg According to CE 1155 E 3 Telescopic plate for fixing on the floor or wall Black lacquered steel core Adjustable 180 º Dimensions 140 x 220 P2 Rigid contraplate Black lacquered metal base Dimensions 65 x 65 in the base and 28 height Diameter: 55 P1 Articulated Contraplate Black lacquered metal base Dimensions: 65 x 65 in the base and 28 height Diameter: 55 114
DOOR-CLOSER 115
DOOR-CLOSER Door closers: Controlled closing system of the door. It makes possible to regulate the closing speed and the final shut of the door. It is installed on doors where the closing must be regulated in order to avoid that the door closes at once and can lead into a danger for people who make use of it, especially with children and elderly people. DOOR -CLOSER DOOR CLOSER DIMENSIONS TABLE For door-closers with guide is necessary to ask for the predisposition of the frame or for its installation the guide will be directly screwed on the wall Door-closer sizes Fuerza EN/1-6 Door set width max. mm Door set weight max. kg 1 750 20 2 850 40 The door-closers that are adjusted in tension from EN 1/2, shall not be fitted in fire doors according to EN 1154 3 4 5 950 1100 1250 60 80 100 6 1400 120 LP - 12 Aluminium reversible door-closer with steel arm. Tension 1/5 (EN 1154) Silver finishing Fire certificate TS-11F Aluminium reversible door-closer with steel arm. Tension 2/3/5 (EN1154) Silver finishing Fire certificate Fire Certificate 116
DOOR-CLOSER TS 1500 DOOR -CLOSER 16 58 50 39 Aluminium reversible door-closer with steel arm. Tension 3/4 (EN 1154) Silver finishing Fire certificate DORMA TS-92 31 334 55 55 207 38 Reversible door-closer with sliding arm Tension 2/4 (EN 1154) Silver finishing Fire certificate TS 12 GUIA 39 493 21,5 60 221 55 60 Reinforced with guide door-closer system Tension 2/4 (EN 1154). The guide is screwed on the wall Silver finishing Fire certificate Fire Certificate 117
A DOOR-CLOSER TS 93 GSR 31 DOOR-CLOSER 470 470 60 60 60 275 275 A= according to the width of the nominal leaf. 53 GEZE 3000 Double leaf door-closers with closing selector incorporated Tension 2/5 (EN 1154) Silver finishing Fire certificate DORMA TS 92 GSR 21,5 1600 mm / 2000 mm / 2500 mm 60 60 221 39 221 60 55. Double leaf door-closer with closing selector incorporated. Tension 2/5 (EN 1154) Silver finishing Fire Certificate 118
SEALS 119
SEALS, POSITION SEALS SEALS: Edges of a fire door, usually fitted in the leaf and frame, it provides to the door a thermal or acoustic insulation All the seals are self-adhesive. Except from the MAC 1 FRAME AND LEAF SEAL LOCATION Jai1 Intumescent Acoustic seal for frame Dimensions: 5 x 20mm Leaf K Frame JAi2 Intumescent Acoustic seal between leaves Dimensions: 5 x 20mm Leaf K JF1 Cold smoke and anti-noise seal for leaf Dimensions. 19 x 15mm Leaf Leaf K Frame JF4 Cold smoke seal for frame MC3 Dimensions: 28 x 15 mm Leaf K Leaf JI 20, JI 30 Standard Intumescent seals: Dimensions: Leaf JI20 for EI 60-20 x 2 mm JI30 for EI 120-30 X 2 mm JI 35, JI 45 Intumescent seals between double leaf Dimensions: JI 35 for EI 60-33 x 2.5 mm JI 45 for EI 120-43 x 2.5 mm Frame Leaf Leaf MAC 1 Ceramic blanket between glass and vision panel Dimensions: 30 x 3mm Leaf Vision panel K Acoustic seal Fire certificated 120
LOUVRES 121
LOUVRES Louvres: Ventilation system installed in multiuse doors to enhance the gas outflow from one place to the other. LOUVRES To install any kind of louvre different from this catalogue, seek for advice in our TECHNICAL DEPARTMENT This louvre installation can only be available in Multiuse doors If the installation is performed in a fire door, our enterprise won t provide EI door certification. PADILLA STANDARD LOUVRE (RJ 1 ) 12 Rows and 10 columns of 29 x 3 mm = 400 = 101,5 189,25 VERTICAL SECTION 360 80 200 122
KICK PLATE 123
KICK PLATE KICK PLATE: protector against knocks used in places with access to trolleys, cart, etc where the door can be pushed violently. -It protects the sheet of the door -Made of aluminium or stainless steel of 1mm thickness. KICK PLATE There are two types: -For the lock area -For the inferior area of the leaf -They are always located on the opposite side of the hinges SINGLE LEAF DIMENSIONS LOCK LEVEL KICK PLATE INFERIOR KICK PLATE A=(B-20)/3 A 8 10 A A 10 A=(B-20)/3 A A 10 A 10 43.5 10 65 65 175 10 220 25 B=L-93 ESP. 1 MM B=L-93 ESP. 1 MM 124