Installation Instructions FE6800 Series Multi-Point Lock To view the QR Code video clips within this document, download a free mobile app and scan the QR Code with your mobile device. The complete video can be viewed on YouTube at https://youtu.be/rj8qgjsym In U.S.: Corbin Russwin, Inc. 5 Episcopal Road Berlin, CT 06037 USA www.corbinrusswin.com In Canada: Door Security Solutions Canada 60 Four Valley Drive Vaughan, Ontario, Canada L4K4T9 www.assaabloy.ca Technical Product Support: Phone: 888-607-5703 WARNING This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov. RH Door Shown 08/08 INSIDE INSIDE INSIDE INSIDE OUTSIDE RIGHT HAND (RH) OUTSIDE LEFT HAND (LH) OUTSIDE OUTSIDE RIGHT HAND REVERSE (RHR) LEFT HAND REVERSE (LHR)
This device is intended to be part of an integrated door, frame and hardware assembly UL-approved for both FEMA 36 and FEMA 30 guidelines for both in-swing and out-swing doors. Tools Supplied /8 Hex 5/64 Hex 5/3 Hex 3/6 Hex Tools Required: Tape Measure Hollow Tip Driver Flat Head Phillips Head 9/6" &/6" Marker Chisel Drill Wrench Anchor Set Tool Flashlight Mallot Mounting Hardware (Full Scale): (4) Oval Head Phillips -4x /" (5) Flat Head Hex Socket -4x" (0) Flat Head Hex Socket /4-0x" () Push-on Retaining Ring ( Spare) () Drive Pin ( Spare) () Drop-in Anchor of 0
VERIFY HANDING INSIDE OUTSIDE Left Hand Door Shown 3 of 0
VERIFY DOOR DIMENSIONS WARNING LOCK IN condition can occur and EMERGENCY EGRESS will be prevented if critical dimensions are not met.! Device will not operate, if door cutouts are not within the dimensions below. Required Door Dimensions 40 4 4 43 44 45 46 4" - 4-3/4" INSIDE OUTSIDE 37-/" - 38-/4" 36 37 38 39 40 4 4 43 If door does not match above dimensions, contact door manufacturer. 4 of 0
. INSTALL DEADBOLT ASSEMBLY Deadbolt Installation () Flat Head Hex Socket /4-0x"! WARNING Deadbolt must be retracted before moving to the next step. 5 of 0
. INSTALL BOTTOM BOLT ASSEMBLY Bottom Bolt Assembly Installation (3) Flat Head Hex Socket -4x" 6 of 0
3. ALIGN BOTTOM BOLT ASSEMBLY Bottom Bolt Assembly Alignment PUSH OR DOWN 3 UP PUSH 7 of 0
4. PREP TOP ASSEMBLY Top Rod Assembly Installation LAY TOP ROD ON DOOR! IMPORTANT THREAD ON FULLY AND TIGHTEN 3 4 5 MARK CLOSEST HOLE 8 of 0
5. INSTALL TOP ASSEMBLY Connecting Top & Bottom Rod Assemblies () Flat Head Hex Socket -4x" 9 of 0
6. ALIGN TOP & BOTTOM ROD PINNING HOLES Align Assembly Pin Holes PUSH GO TO STEP 7 Top Rod Bottom Rod GO TO STEP 6a OR 6b 0 of 0
6a. ADJUST MISALIGNED PINNING HOLES UP Adjust Plunger If Necessary PUSH Top Rod Bottom Rod 3 = 4 of 0 GO TO STEP 7
6b. ADJUST MISALIGNED PINNING HOLES DOWN Adjust Plunger If Necessary PUSH Top Rod Bottom Rod 3 = 4 of 0 GO TO STEP 7
7. PIN THREE ASSEMBLIES () Drive Pin () Push-on Retaining Ring Insert Drive Pin INSIDE OUTSIDE 8. MOUNT DOOR TO FRAME! Do not trim door if door rubs along floor! Right Hand Door Shown 3 of 0
9. CHECK FOR HOLD OPEN Test Deadbolt Retraction PUSH GO TO STEP 0 3 GO BACK TO 4 of 0
0. ADJUST DEVICE Plunger Rotations! Device Must Be In HOLD OPEN Before Adjusting Device! Hand Tighten =! Must Rotate Exactly 3 Revolutions 3x 5 of 0
. TRIGGER DEVICE & FINAL CHECK Device Check PUSH PUSH 3 GO BACK TO STEP 0 GO BACK TO STEP 0 6 of 0
. ASSEMBLE CYLINDER INTO OUTSIDE TRIM Cylinder Installation 3. MOUNT OUTSIDE AND INSIDE TRIM Mount Inside and Outside Trim INSIDE OUTSIDE (4) Oval Head Phillips -4x /" 7 of 0
4. INSTALL TOP LATCH INTO DOOR FRAME Top Latch Installation (4) Flat Head Hex Socket /4-0x" 5. ATTACH DEADBOLT STRIKE PLATE TO FRAME Deadbolt Strike Plate Installation () Flat Head Hex Socket /4-0x" 8 of 0
6. PREPARE FLOOR FOR BOTTOM STRIKE a () Flat Head Hex Socket /4-0x" b 9 Dimensions for Bottom Strike Plate Installation c d e 3 -/8" Dia. x 7/8" Deep 9 of 0
7. INSTALL BOTTOM STRIKE /4" MAX Bottom Of Door To Top of Strike Bottom Strike Plate Installation Chisel as required 3 3/8" Dia. x -/" Deep /8" Deep 8. TEST INSTALLATION! IMPORTANT 5/64 Hex Tighten after door is adjusted and works properly. 0 of 0