SVENSK STANDARD SS-ISO 7588-2 Handläggande organ Fastställd Utgåva Sida SVENSK MATERIAL- & MEKANSTANDARD, SMS 1999-08-27 1 1 (1+7) Copyright SIS. Reproduction in any form without permission is prohibited. Road vehicles Electrical/ electronic switching devices Part 2: Electronic devices Vägfordon Elektriska/ elektroniska kopplingsdon Del 2: Elektronikreläer The International Standard ISO 7588-2:1998 has the status of a Swedish Standard. This document contains the official English version of ISO 7588-2: 1998. This standard supersedes the Swedish Standard SS-ISO 7588, edition 1. Swedish Standards corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Den internationella standarden ISO 7588-2:1998 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av ISO 7588-2:1998. Standarden ersätter SS-ISO 7588, utgåva 1. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. ICS 43.040.10; 43.040.20 Standarder kan beställas hos SIS som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08-610 30 00. Telefax: 08-30 77 57 Upplysningar om sakinnehållet i standarden lämnas av SMS. Telefon: 08-459 56 00. Telefax: 08-667 85 42 E-post: info@sms-standard.se Prisgrupp L Tryckt i oktober 1999
Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 7588-2 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical and electronic equipment. ISO 7588 consists of the following parts, under the general title Road vehicles Electrical/electronic switching devices: Part 1: Relays and flashers Part 2: Electronic devices Part 3: Microrelays Annexes A and B of this part of ISO 7588 are for information only. ISO 1998 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 CH-1211 Genève 20 Switzerland Internet iso@iso.ch Printed in Switzerland ii
INTERNATIONAL STANDARD ISO Road vehicles Electrical/electronic switching devices Part 2: Electronic devices 1 Scope This part of ISO 7588 specifies dimensional characteristics of electronic devices intended for road vehicles. Annex A gives additional information on the dimensions of socket apertures and annex B gives recommended terminal identification. 2 Normatives references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 7588. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 7588 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 8092-1:1996, Road vehicles Connections for on-board electrical wiring harnesses Part 1: Tabs for singlepole connections Dimensions and specific requirements. ISO 8092-2: 1), Road vehicles Connections for on-board electrical wiring harnesses Part 2: Definitions, test methods and general performance requirements. 3 Definitions For the purposes of this part of ISO 7588, the definitions given in ISO 8092-2 apply. 4 Dimensions and other requirements 4.1 General Dimensional characteristics and other requirements are specified in 4.2 to 4.4. 1) To be published. (Revision of ISO 8092-2:1996) 1
ISO NOTE All corresponding dimensions also apply if less than nine tabs are fitted. The dimensions of socket apertures given in annex A are for information only. 4.2 Positioning zones of the tabs and socket apertures 4.2.1 Location of tabs and apertures True position See figure 1. Dimensions in millimetres Figure 1 4.2.2 Dimensional limits of the tabs See figure 2. The tabs shall be in accordance with ISO 8092-1, sizes 6,3 0,8, and 2,8 0,8 respectively, and shall not have shoulders. Dimensions in millimetres Figure 2 2
ISO 4.3 Overall dimensions and other requirements for electronic devices See figure 3 and table 1. Configurations other than rectangular are permitted, provided they lie within the specified area. However, in all cases the outside contour shall lie within the dimensions X and Y (maximum) given in figure 3 and in table 1. Figure 3 Size type X Table 1 Y 1 Dimensions in millimetres Y 2 Z C 15,3 5,0 25,7 55 D 17 9,6 30,3 55 E 20 9,6 30,3 55 4.4 Other requirements for sockets 4.4.1 Apertures at the entering plane shall be in accordance with figure 1 and shall accept tabs to the maximum limits. 4.4.2 In order to avoid the need for excessive withdrawal force, it is recommended that the female connectors in the socket should not incorporate detents. 5 Functional allocation of electronic device terminals No functional allocation of terminals has been established for this part of ISO 7588. No terminal identification has been specified but a recommended practice is given in annex B. 3
ISO 6 Designation Electronic devices in accordance with this part of ISO 7588 shall be designated as shown in the following example. EXAMPLE NOTE A manufacturer s reference number should be used to identify products with differing functional allocation. 4