INSTLL GUIDE OEM-L(RS)-NI-[DS-LC]-EN DOCUMENT NUMER REVISION DTE 0 FIRMWRE OEM-L(RS)-NI-[DS-LC] HRDWRE DS-LC CCESSORIES DS-US (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 EFORE INSTLLTION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
MODEL YER INSTLL TYPE DT IMMOILIZER YPSS SECURE TKEOVER PRKING LIGHT CTRL X LOCK REMOTE STRT RM OEM LRM DISRM OEM LRM DOOR LOCK DOOR UNLOCK PUSH TO STRT CTRL RP SHUTDOWN CTRL DOOR STTUS MONITORING TRUNK STTUS MONITORING RKE PEDL STTUS MONITORING TCHOMETER STTUS MONITORING HORN CTRL NISSN MKE VEHICLE LIST - OF U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN PGE OF DOC.: # 0 FETURES Rogue PTS T - Rogue PTS T
PGE OF DOC.: # 0 OX CONTENTS - OF OX CONTENTS WHITE WHITE PIN LCK CONNECTOR PIN WHITE CONNECTOR MODULE WHITE LUE PROGRMMING UTTON 0 PIN LCK CONNECTOR PIN WHITE CONNECTOR LED F C E D 0 LCK PIN WHITE CONNECTOR DT CLE PIN LUE CONNECTOR DT CLE LCK DT PORT (WELINK, RF, TELEMTIC) WELINK CLE (required accessory sold separately) WELINK CLE MODULE DT PORT COMPUTER US PORT PIN LCK CLE U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN
PGE OF DOC.: # 0 COMPONENT LOCTOR - OF INTERIOR VIEW DRIVER SIDE VIEW PSSENGER SIDE VIEW C U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN
PGE OF DOC.: # 0 U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 CONNECTOR COLOR CONNECTOR TYPE POSITION POLRITY MODULE LOCTION COMPONENT LOCTOR CanH ODII White pin 0 lue (DT) t ODII connector CanL ODII White pin Pink (DT) t ODII connector PTS M lack 0 pin 0 Yellow t CM Ignition ODII White pin 0 Yellow (+) t ODII connector V ODII White pin White (+) t ODII connector Unlock M lack 0 pin Pink t CM Lock M lack 0 pin rown t CM - Power Liftgate WIRE COLOR CONNECTOR NME YER MODEL Rogue PTS T WIRE DESCRIPTION NISSN MKE TYPE - WIRE CHRT - OF ~ Green 0 pin 0 LtGreen t switch, on lower dash panel Ground ODII White pin 0 lack t ODII connector Negative Starter E lack pin Green t CM Negative Ignition M Gray 0 pin Yellow t CM Negative Ignition M Gray 0 pin LtPurple/White or Green/White t CM Negative Ignition M Gray 0 pin rown t CM Hazard Light M Gray 0 pin Yellow t CM OEM-L(RS)-NI-[DS-LC]-EN
PGE OF DOC.: # 0 TYPE - WIRING DIGRM - OF ODII CONNECTOR (UNDER DRIVER SIDE DSH) MODULE IGNITION (+) - 0 CNL - CNH - 0 GROUND - 0 F C E DT D V (+) - 0 CM (LEFT OF STEERING COLUMN) 0 GRY/YELLOW (NC) 0 GRY/RED - LOCK OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - UNLOCK OUTPUT 0 LUE/YELLOW - STRTER OUTPUT 0 LUE/RED - GROUND INPUT NEG. STRTER - : E LCK 0 0 PINK - IGNITION (+) INPUT 0 PINK/LCK (NC) 0 ORNGE (NC) 0 ORNGE/WHITE - TRUNK OUTPUT 0 ORNGE/LCK - PTS OUTPUT 0 ROWN/YELLOW - CNL 0 ROWN/RED - CNH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/LCK (NC) C LOCK/RM - UNLOCK/DISRM - PTS - 0 DIODE N00 DIODE N00 NEG. IGNITION - E : M GRY 0 0 NEG. IGNITION - POWER LIFTGTE - 0 NEG. IGNITION - POWER LIFTGTE SWITCH : GREEN WITHOUT COMPTILE CCESSORY 0 0 HZRD LIGHT - 0 WHITE - GROUND INPUT 0 WHITE/RED (NC) 0 WHITE/LCK - IGNITION OUTPUT LUE/WHITE (NC) WHITE (NC) LCK - GROUND RED - V (+) 0 0 DIODE 0 0 0 0 : M LCK 0 0 N00 D 0 OR F 0 DT CLE COMPTILE CCESSORY WITH COMPTILE CCESSORY. IMPORTNT: SEE THE COMPTILE CCESSORIES PGE FOR DETILS. 0 GREEN/LCK - HOOD STTUS INPUT 0 LUE/LCK (NC) 0 RED/WHITE (NC) WITHOUT OEM HOOD SWITCH: 0 ROWN (NC) INSTLL ND CONNECT TO 0 PURPLE/YELLOW (NC) FTERMRKET HOOD SWITCH 0 PURPLE/LCK (NC) 0 WHITE (NC) 0 LCK/WHITE (NC) 0 GREEN - PRKING LIGHT OUTPUT 0 PURPLE/WHITE (NC) OEM REMOTE REMINS FUNCTIONL DURING REMOTE STRT SEQUENCE U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 FTERMRKET HOOD SWITCH OEM-L(RS)-NI-[DS-LC]-EN
PGE OF DOC.: # 0 U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 CONNECTOR TYPE POSITION POLRITY MODULE LOCTION COMPONENT LOCTOR CanH ~ Green 0 pin 0 lue (DT) t CM CanL ~ Green 0 pin 0 Pink (DT) t CM PTS M lack 0 pin 0 Yellow t CM Ignition ODII White pin 0 Yellow (+) t ODII connector V ODII White pin White (+) t ODII connector Unlock M lack 0 pin Pink t CM Lock M lack 0 pin rown t CM Power Liftgate ~ Green 0 pin 0 LtGreen t switch, on lower dash panel Ground ODII White pin 0 lack t ODII connector Negative Starter E lack pin Green t CM Negative Ignition M Gray 0 pin Yellow t CM Negative Ignition M Gray 0 pin LtPurple/White or Green/White t CM Negative Ignition M Gray 0 pin rown t CM Hazard Light M Gray 0 pin Yellow t CM OEM-L(RS)-NI-[DS-LC]-EN WIRE COLOR CONNECTOR COLOR CONNECTOR NME YER MODEL Rogue PTS T WIRE DESCRIPTION NISSN MKE TYPE - WIRE CHRT - OF
PGE OF DOC.: # 0 TYPE - WIRING DIGRM - OF ODII CONNECTOR (UNDER DRIVER SIDE DSH) MODULE IGNITION (+) - 0 C E DT V (+) - 0 CM (LEFT OF STEERING COLUMN) 0 GRY/YELLOW (NC) 0 GRY/RED - LOCK OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - UNLOCK OUTPUT 0 LUE/YELLOW - STRTER OUTPUT 0 LUE/RED - GROUND INPUT NEG. STRTER - : E LCK 0 0 PINK - IGNITION (+) INPUT 0 PINK/LCK (NC) 0 ORNGE (NC) 0 ORNGE/WHITE - TRUNK OUTPUT 0 ORNGE/LCK - PTS OUTPUT 0 ROWN/YELLOW - CNL 0 ROWN/RED - CNH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/LCK (NC) LOCK/RM - UNLOCK/DISRM - PTS - 0 DIODE N00 DIODE N00 DIODE LUE/WHITE (NC) WHITE (NC) LCK - GROUND RED - V (+) 0 DT CLE : M GRY 0 0 NEG. IGNITION - WITHOUT COMPTILE CCESSORY COMPTILE CCESSORY NEG. IGNITION - CNH - 0 CNL - 0 POWER LIFTGTE - 0 OR NEG. IGNITION - : GREEN 0 0 0 0 POWER LIFTGTE SWITCH : GREEN WITH COMPTILE CCESSORY. IMPORTNT: SEE THE COMPTILE CCESSORIES PGE FOR DETILS. 0 0 HZRD LIGHT - 0 WHITE - GROUND INPUT 0 WHITE/RED (NC) 0 WHITE/LCK - IGNITION OUTPUT 0 0 0 0 0 0 E : M LCK 0 0 N00 D 0 C F GROUND - 0 F D 0 GREEN/LCK - HOOD STTUS INPUT 0 LUE/LCK (NC) 0 RED/WHITE (NC) WITHOUT OEM HOOD SWITCH: 0 ROWN (NC) INSTLL ND CONNECT TO 0 PURPLE/YELLOW (NC) FTERMRKET HOOD SWITCH 0 PURPLE/LCK (NC) 0 WHITE (NC) 0 LCK/WHITE (NC) 0 GREEN - PRKING LIGHT OUTPUT 0 PURPLE/WHITE (NC) OEM REMOTE REMINS FUNCTIONL DURING REMOTE STRT SEQUENCE U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 FTERMRKET HOOD SWITCH OEM-L(RS)-NI-[DS-LC]-EN
PGE OF DOC.: # 0 MODULE PROGRMMING PROCEDURE - OF 0 Set ignition to ON position. CC ON STRT 0 STRT 0 0 CC Set ignition to position. CC ON STRT STRT ON STRT STRT Wait, LED will turn solid RED, then solid GREEN for second, then solid RED. 0 WRNING: Disconnect power last. Disconnect module from vehicle. Set ignition to position. 0 Connect module to computer and proceed with extended programming. Wait, LED will turn. 0 Connect power first. Connect module to vehicle. Set ignition to ON position. ON STRT Set ignition to position. CC Module Programming Procedure completed. STRT 0 0 CC ON STRT STRT 0 Set ignition to ON position. CC ON STRT STRT Wait, LED will flash GREEN rapidly. U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 Wait, LED will turn solid GREEN for seconds. OEM-L(RS)-NI-[DS-LC]-EN
VLET MODE PROGRMMING PROCEDURE - OF NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within seconds. 0 CC ON STRT PGE 0 OF DOC.: # 0 To exit valet mode: repeat steps to. Cycle ignition ON five times [x /ON] rapidly. STRT 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. CC ON STRT STRT 0 Valet Mode Programming Procedure completed. U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN
PGE OF DOC.: # 0 MODULE NVIGTION PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 Module must be programmed to the vehicle. 0 Use the Module Navigation Chart on the next page. 0 Set ignition to position. 0 TO CCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 0 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 0 0 CC ON STRT TO CCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO CCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MNDTORY: EXIT MODULE NVIGTION. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. STRT 0 0 [X] U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN
PGE OF DOC.: # 0 [Y] OPTIONS [X] MENUS MODULE NVIGTION CHRT: NOTES I Default settings are listed in bold. 0 II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 DISRM/UNLOCK EFORE STRT RELOCK FTER STRT RELOCK FTER SHUTDOWN 0 ON 0 0 ON 0 0 ON 0 0 ON FORCE UNLOCK LL ON FIRST PRESS 0 N/ 0 N/ 0 N/ 0 N/ 0 DISLE 0 N/ 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 SEC 0 0 SEC 0 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0- N/ 0 N/ 0 0 N/ FCTORY KEYLESS RS SEQUENCE CONFIGURTION 0 0 0-0 Technical Support only 0 0 0 0 [Z] SETTINGS MODULE NVIGTION CHRT - OF MODULE RUN TIME WIT TO STRT DELY N/ *Vehicle will shutdown when a door is opened. U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN
[X] NUMER OF PRKING LIGHT FLSHES DIGNOSTIC REMOTE STRTER ERROR CODES - OF I WRNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is ON. 0 Hood is open. II fter a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 0 Glow plug timeout error. REMOTE STRTER ERROR CODES: NOTES U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN PGE OF DOC.: # 0
I II III DURING PROGRMMING DURING REMOTE STRT WITH IGNITION U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 DIGNOSTIC TEST MODULE LED STTUS MODULE DIGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN dditional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. OEM-L(RS)-NI-[DS-LC]-EN PGE OF DOC.: # 0
MODULE RESET PROCEDURE - OF 0 Disconnect all connectors from module except the LCK -PIN connector. 0 Reconnect all connectors. 0 Disconnect the LCK -PIN connector. 0 Repeat programming procedure. 0 PRESS ND HOLD programming button while connecting the LCK -PIN connector. Failure to follow procedure may result with a DTC or a CHECK error message. 0 Wait, LED will flash RED. RELESE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN PGE OF DOC.: # 0
TKEOVER PROCEDURE - OF ll vehicle doors must be closed and locked prior to remote start sequence. 0 Take over procedure completed. 0 Time restriction. Complete steps to within seconds. Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote or request switch. 0 Open driver door and enter vehicle. 0 Close driver door. 0 Press and release RKE pedal. U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN PGE OF DOC.: # 0
INSTLLTION CHECKLIST - OF PGE OF DOC.: # 0 CHECKLIST WRNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. Exit vehicle. Installation checklist completed. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. U.S. Patent No.,,0 utomotive Data Solutions Inc. 0 OEM-L(RS)-NI-[DS-LC]-EN