New England TallBoy ssembly nstructions - please keep for future reference QN9 464/3944 Dimensions Width - 30cm Depth - 24cm Height - 172cm mportant Please read these instructions fully before starting assembly ssue 1-16/05/2016
Safety and are dvice mportant Please read these instructions fully before starting assembly heck you have all the components and tools listed on page 2 plastic bags and separate them into their groups. During assembly do not stand or put weight on the product, this could cause damage. ssemble the item as close room) as possible. Keep children and animals away from the work area, small parts could choke if swallowed. ssemble on a soft level surface to avoid damaging the ake sure you have enough space to layout the parts before starting. Parts of the assembly will be easier with 2 people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the using. Only use hand screwdrivers are and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Handy Hints ssemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts Regularly check and ensure tightend properly. 1
omponents - Panels Please check you have all the panels listed below 2 x1 1 x1 30X24X1.5cm 7 x1 84.5X22.5X1.5cm 84.5X22.5X1.5cm 8 x1 86X26X0.3cm 4 x1 3 x1 9 x1 78X26X0.3cm 30X2 4X1.5cm 5 x1 84.5X22.5X1.5cm x2 10 x1 24X2 2X1.2cm 84.5X22.5X1.5cm 25X2 2X1.2cm 6 x1 75.7X23.7X1.2cm 12 x2 25X2 0X1.2cm 13 x1 24X7 X1.2cm omponents - Fittings Note: may be supplied than are required. x20 5.8x30mm x8 4x35mm B x8 25x6mm K x1 x8 12x10mm L x3 3x16mm D x2 x26 2.5X12mm E x2 3x10mm N x1 F x1 G x1 H x1 x16 0 x1 P x4 Q x1 Tools required Phillips screwdriver (medium & large) 2
3
ssembly nstructions Step 1 1. nsert 4 x Dowels into the bottom edge of upper left panel 2 and 3. upper right panel 3 3 2 2. onnect panels 22 and 33 to iddle Panel 99 as shown using 4 x Screw Step 2 1 1. nsert 4 x Dowels into the top edge of panels 22 and 33. 9 2. onnect Top Panel to panels 22 and 3 using 4 x Screw Step 3 1. nto Lower left panel 44 insert 2 x ale amlocks BB and 4 x Dowels as shown. 5 4 2. Repeat for Lower 5 right panel 5. B B B B 10 1. onnect Panels 10 13 to panels 44 and 13 and 55 as shown. Step 4 5 4 2. nsert 4 x Female camlocks and tighten 10 13 4
ssembly nstructions Step 5 1. nto the underside of iddle panel 9 insert 4 x ale amlocks BB and 4 x Dowels. 9 B B B B Step 6 1. nsert 2 x Hinge Pins D into the Top and D Bottom of Door 6. 6 66 4. nsert 4 x female camlocks and tighten with a Phillips Screwdriver 3. Locate the upper section onto the lower section as shown. 2. Locate the lower hinge into hole in Base panel 10 D 77 D 88 1. On the reverse of the unit connect Upper back panel 7 and lower back panel 88 as shown using 26 x Screw Step 7 5
ssembly nstructions Step 8 1. nto the Upper section insert 8 x Shelf Supports 2. nto the Lower section insert 8 x Shelf Supports 3. nto the underside of iddle panel 99 connect K agnetic atch K using 2 x Screw LL 9 4. To Door 66 onnect atch Plate FF using 2 x Screw EE E E L L G 5. onnect your choice of handle, either handle G or Q Q with Screw H G H as shown FF K H 6 Step 9 1. nsert 2 x Shelves 12 as and 2 x Shelves 12 shown. 2. dd 4 x Protective Feet PP 12 12 12 12 P P P P 6
ssembly nstructions Step 10 0O 2.ove the unit into desired position. Warning: The unit is heavy. Lift with care. 3. ark the wall with a suitable scribe the position of the fixing holes. Warning: Before driling,check wall for hidden pipes and cables. 4. Drill hole and insert 1 x O O wall plug D 5. onnect to the wall O using 1 x screw D as shown ssembly omplete L 1. On the reverse of the unit, in position shown, fix 1 x Wall Straps N using 1 x Screws LL N O This unit is floor standing but we recommend