041137c 1 08.25.16 Important Notes: Please read entire guide before beginning fixture installation. For installation by a qualified electrician familiar with the construction and operation of luminaire electrical systems and the hazards involved. Must be installed and wired in accordance with all local and national electrical codes. Wall mounting hardware is not included due to the wide variety of wall materials. Customer should determine the appropriate anchoring hardware for their specific needs. #8 mounting hardware is recommended. Components included: 3 Wire Connectors Note: Depending on control option, some connectors may not be used. Chassis Mounting Plate (attached) #8-32 Locking Screw Tools required: Not Included: Note: The LED fixture will include the LED light source No. 2 Phillips head screwdriver Wire cutter / stripper CFL 26 W, 32 W, or 42 W CFL 1 www.lutron.com/ivalo
Aliante Aliante Exterior Demi-Sconce Exterior Demi-Sconce LED /LED CFL / CFL Suitable for wet Suitable forlocations wet locations 041137c 2 08.25.16 041137b 09/2014 09/2014 041137b 1. 1. 2. Turn the circuit breaker. Turn off off power power to the the fixture location. location. Turn off to fixture cross-bar, cross-bar, present, and loosen connecting loosen connecting cross-bar,ifififpresent, present,and and loosen screws from fromscrews junctionfrom box (octogonal (octogonal or rectangular). rectangular). screws junction box or connecting junction box (octogonal! or rectangular). WARNING: Shock Hazard. May result in serious injury or death. Turn off power to all feeds before wiring or servicing. 3. 3. 4. 4. screwsto toseparate separatechassis chassis from 44 screws to separate chassis from back from back back mounting plate. Setand cover and screws mounting plate. Set Set cover cover and screws aside. mounting plate. screws aside. aside. Pull wires from junction box through back plate as shown. Slip the back plate over the connecting screws and tighten. Be careful not to pinch any wires. Wall mount in vertical position only. 2 www.lutron.com/ivalo
041137c 3 08.25.16 5. Make corresponding connections as illustrated below using wire connectors. Green Ground White White Black Line / Hot For ballast or LED driver replacement by a qualified electrician: Disconnect solid leads from ballast / driver, replace ballast / driver, and reconnect according to color designation on ballast / driver label. 3 www.lutron.com/ivalo
041137c 4 08.25.16 6. Replace chassis over back mounting plate. Align screw holes and re-install 4 screws. NOTE: Lutron recommends the use of # 8 mounting hardware. At the foot of the Sconce is an additional hole for a screw to fasten to the wall. Wall mounting hardware is not included due to the wide variety of wall materials. Customer should detemine the appropriate anchoring hardware for their specific needs. 4 www.lutron.com/ivalo4
7. Insert appropriate wattage lamp in socket. See label on product for lamp specifications (light source provided with LED model). 041137c 5 08.25.16 8. protective cover (LED models only). Slip shell mounting bracket into appropriate clips. LED CFL 9. Insert and tighten locking cover screw into the bottom mounting bracket. 10. Turn on the power. 5 5 www.lutron.com/ivalo
041137c 6 08.25.16 Limited Warranty For warranty details, see www.lutron.com/technicaldocumentlibrary/3683454.pdf Trademarks Lutron, )Lutron, IVALO, IVALO Lighting (registered in the U.S. only), and Aliante are registered trademarks and Ivalo Collection is a trademark of Lutron Electronics Co., Inc. For Help For help with applications or installations, please contact us at 610.282.7472 or fixtures@lutron.com Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, USA World Headquarters 610.282.3800 Customer Service: 610.282.7472 Fax: 610.282.7600 fixtures@lutron.com www.lutron.com/ivalo 2014 2016 Lutron Electronics Co., Inc. 6 www.lutron.com/ivalo