SERVICE MANUAL HOSTESS TROLLEY U.K. 0312 200 15110 - HL6200DB (Mahogany) 0312 200 15210 - HL6200LB (Teak) 0312 200 15227 - HL6200GO ( Golden Oak) Service Hints Technical Data Wiring Diagram Exploded Views Parts List - Page 1 - Page 2 - Page 3 - Page 4 - Page 5 May 2016
DISASSEMBLY AND ASSEMBLY HL6200 SERIES ENSURE APPLIANCE IS DISCONNECTED FROM THE ELECTRICITY SUPPLY BEFORE DISASSEMBLING. NOTE ALL CONNECTION DETAILS AND ROUTING OF LEADS BEFORE DISASSEMBLING. Numbers appearing in the text refer to illustrations and parts list numbers. A. SLIDING TABLETOPS Slide both tabletops open. Remove cover caps 130 and the two screws securing handle. Withdraw the handle from the tabletop assembly. Slide the tabletop required inwards, past its closed position, until the two plastic sliding blocks on the cabinet Channels are exposed. Withdraw the sliding blocks from the cabinet channels and then slide the tabletop assembly out clear of the channels. B. GLASS DOOR 1. Remove the two miniature countersunk screws at each end of the glass door handle. 2. Drill out the rivet securing striker plate 115, using a 2.5mm bit. Use extreme care when drilling. 3. While supporting glass door 113, remove striker plate 115, handle and inner steel channel 506. 4. Splay side channel assemblies 509 & 511 slightly and lift the glass door away. 5. Replace the glass door in reverse order in reverse order ensuring: I Cushion strips are correctly fitted between the ends of the glass door and the side channels II Insert 514 is fitted to the hole in the glass door before assembling and inserting a new rivet size 2.4mm x 7.5mm. C. TOP ELEMENT ASSEMBLY 1. From inside of cabinet, squeeze locking barbs and release mains lead bush 121 retainer from rear panel. Remove rear cover strip 510, secured by a single screw, to the extent of the mains lead wires. Disconnect the top element leads from terminal block 120. NOTE: Terminal block 120 includes push-in locking terminals for internal wiring. Leads inserted in the front-most terminals may only be released by inserting a small screwdriver or similar in the slots provided in the front of the terminal block. Rear-most leads may release with a sharp pull. If leads cannot be released, or are not gripped on insertion, item 120 must be replaced. 2. Open the sliding tabletops and remove glass dishes and lids 101 and holders 103. 3. Remove the sliding tabletops as in A.1. Then slide each tabletop in turn inwards past its closed position to gain access to the four screws securing top element assembly 107. 4. Use a powerful magnet or suitable tool to lift the element assembly out clear of the cabinet, feeding the element wires through grommet 110 in the cabinet. 5. Refit in reverse order, taking care that the rear cover strip fixing screw is clear of cables when fixing.
HL6200 SERIES D. MIDDLE SHELF ELEMENT ASSEMBLY AND NEON 1. Remove rear cover strip 510 as shown in C.1. And disconnect the middle shelf element leads from Terminal block 120 (see note in C.1.) 2. Remove the two screws securing the element assembly through the rear panel of the cabinet and two screws from under the front edge of the shelf see fig. 1. Open the glass door. 3. Lift the element assembly out clear of the cabinet, feeding the element wires through grommet 110 in the cabinet. 4. Neon 118 is a push fit assembly, located by two barbs that spring open behind element panel trim 515. It can only be removed from the front. Pushing from behind the neon assembly (inside the front shelf rail) using a suitable tool can assist removal. To re-fit, thread the neon leads through the hole in the element panel trim 515, push-fit neon into hole and route with element leads to terminal block. 5. Re-fit in reverse order, taking care that the rear cover strip fixing screw is clear of cables when fixing. ELEMENT ASSEMBLY FIXING SCREWS ELEMENT ASSEMBLY FIXING SCREWS Rear view Front view Fig. HL6200 Element Assembly Fixing Points E. MAINS LEAD 1. Remove rear cover strip 510 as in C.1. 2. Disconnect LIVE and NEUTRAL mains lead wires from terminal block 120: release the earth lead from the cabinet earth stud. 3. To remove mains lead bush 121, rotate the retainer arm through 90, then use pliers to squeeze the mains lead locking tab and push the bush, complete with mains lead, out of the cover strip. 4. Refit in reverse order, ensuring correct wire colour connections and that a sound earth connection is made.
F. CABINET ITEMS HL6200 SERIES 1. Magnetic catch 111 is a push-fit in front top panel 109. 2. To remove front top panel 109, remove both sliding table tops completely (see A.1.) and magnetic catch 111. Drill out the rivet at each end of the front slide panel using a 3mm bit. Use extreme care when drilling. Withdraw leg top caps, and then remove the front top panel assembly. Refit in reverse order. 3. Castor wheels 116 are a push-fit onto castor wheel inserts 117. The castor wheel inserts are a push-fit into the cabinet. Remove by prising out with care. THEORETICAL WIRING DIAGRAM L E CUPBOARD TOP (MIDDLE) NEON ELEMENT ELEMENT N SPECIFICATION Voltage Loading Cord length Pre-heat time Finish Dimensions (approx) 230 V a.c. 50 Hz 355 W 2 m 30 minutes approx See text 725mm W x 380mm D x 695mm H SERVICE INFORMATION The elements used in this appliance are of the adhesive variety and cannot be removed easily. For this reason, elements and plates are supplied as complete assemblies.
Oval Dishes HL6200 Hostess Trolley - Exploded View 1 122 120 121 110 510 504 508 101 103 107 130 117 116 109 503 111 118 515 509 112 113 506 115 511 500
122 120 121 110 510 504 508 1.6 Ltr Round Dishes HL6200 Hostess Trolley - Exploded View 2 101 103 107 130 117 116 109 503 111 118 515 509 112 113 506 115 511 500
2 Ltr Round Dishes HL6200 Hostess Trolley - Exploded View 3 122 120 121 110 510 504 508 101 103 107 130 117 116 109 503 111 118 515 509 112 113 506 115 511 500
HL6200 Hostess Trolley - Parts List Item Description Part Number Expolded View 1 - Serial No's up to 1440567166 101 Glass Dish & Lid (Oval) 0101 092 21701 103 Glass Dish Holder (Oval) 0101 082 12221 Exploded View 2 - Serial No's 1440567167-1539822969 101 Glass Dish & Lid (1.6 Ltr Round) 0101 092 66321 103 Glass Dish Holder (1.6 Ltr Round) 0101 082 15401 Exploded View 3 - Serial No's 1540825398 and higher. EXCEPT FOR 1544849347 to 1544849466, 1544852442 to 1544852464, 1544852506 to 1544852540. 101 Glass Dish & Lid (2 Ltr Round) 0101 092 69011 103 Glass Dish Holder (2 Ltr Round) 0101 082 15441 Table Top Cover (HL6200LB & HL6200GO) 0101 092 36831 Table Top Cover (HL6200DB) 0101 092 36841 Table Top Handle 0101 077 61391 Table Top Sliding Block 0101 077 64311 107 Top Element Assembly 0101 089 22511 Leg Top Cap 0101 077 61311 109 Front Top Panel (HL6200LB & HL6200GO) 0101 070 12261 109 Front Top Panel (HL6200DB) 0101 070 12021 110 Grommet Sleeve 0101 078 53301 111 Magnetic Catch (FS10) 0101 078 53351 112 Mid Element Assembly 0101 089 22 113 Glass Door Printed 0101 177 07531 Handle Extrusion Drilled 0101 077 61331 115 Striker Plate 0101 070 12141 116 Castor (Pack of 4) 0101 078 53291 117 Castor Insert 0101 077 61302 118 Neon Assembly 0101 078 57811 120 Terminal Block 0101 078 53262 121 Strain Release Bush 0101 077 61511 122 Cordset (UK) 0101 076 90741 130 Screw Cover Cap 0101 077 61382 500 Glass Door Printed Assembly 0101 092 63851 Top Cover Support Assembly 0101 089 22361 Outer Glide 0101 082 12081 503 Outer Glide Cover Printed 0101 077 61491 504 Outer Glide Cover 0101 082 12131 509 Right Hand Door Chain Linkage 0101 089 22631 510 Wiring Cover 0101 082 12061 511 Left Hand Door Chain Linkage 0101 089 22641 515 Element Panel Trim 0101 082 12361 n/a User Instruction Booklet 0101 194 12762 Bold text indicates choice of parts depending on the model version