Constant-current Power Module Features 1.Input voltage range:ac90 ~ 264V 2.As output current can also be arbitrarily set by a resistor 3.Power factor:85% or more 4.Dimming is possible by PWM or linear signal from the outside 5.Dielectric withstand voltage:ac3000v rms Applications Sidewalk lights Security lights Other outdoor lighting Certified safety standards None Applicable safety standards Electrical Appliance and Material Safety Law_Appendix 12/J61347-1,2-13 Electrical Appliance and Material Safety Law_Appendix 8 IEC/EN61347-1, 2-13 UL8750 Applicable input voltage range AC90V-264V AC90V-150V AC90V-264V AC90V-264V Application circuit Method to select external parts for input rectification and smoothing as well as output smoothing is supported by the application note 1 / 14
Input-output condition Item Specification Conditions Note CPM3417RA Datasheet Input voltage range Rated input voltage AC90V~264V(47Hz~63Hz) AC100V, AC240V(50Hz,60Hz) Max output power 17W Vo=34V, Io=500mA Output voltage range 17V~34V Refer to the Output specifications range Default output current 400mA Output current variable range 400mA~500mA Refer to the Output specifications range DIM pin max voltage 5.5V DIM pin votage 0.66V min (0.70V typ) OFF Voltege 2.6V max (2.45V typ) ON Voltege PWM dimming signal 800Hz~1200Hz (1000Hz typ) Duty:5%~100% Linear dimming signal 0.66V~2.6V (typ:0.70v~2.45v) Electrical specification Item Specification Conditions Note Efficiency 84% TYP Rated input voltage At max output power Output current accuracy 85% or more Rated input voltage At max output power Output current accuracy ±10% Output current overshoot 1.8A or less At input voltage reintroduction Protection Item Specification Conditions Note Overload protection Auto recovery Overvoltage protection Auto recovery Output voltage:38v~60v Overheat protection Auto recovery Insulation Item Specification Conditions Note Dielectric withstand voltage AC3.0kV 1min Cutoff 2mA (Between Pri-Sec) Insulation resistance 100MΩ or more DC500V (Between Pri-Sec) 2 / 14
Environmental conditions Item Specification Conditions Note CPM3417RA Datasheet Operating temperature -20 ~70 Refer to the Ambient temperature derating curve Operating humidity Storage temperature Storage humidity 20~95%RH (No condensation) -25 ~85 5~95%RH (No condensation) Measurement circuit Measuring instrument Symbol Part No. Manufacturer E1 AC power supply W1 Power meter / WT210 YOKOGAWA RL1 Electronic load V1 Voltmeter / Class 0.5 A1 Currentmeter / Class 0.5 Parts structure Symbol Description Part No. Manufacturer Symbol Description Part No. Manufacturer L101 Inductor LF4ZTM-E333 KORIN R101 Resistor 1MΩ ±5% 0.25W L102 Inductor PI10a-471K KORIN R102 Resistor 1MΩ ±5% 0.25W L201 Inductor 0-5127-15 KORIN R103 2 Resistor OPEN D101 Diode S1NBC80 SHINDENGEN R104 2 Resistor OPEN D201 1 OPEN R105 2 Resistor OPEN C101 Capacitor LE104-MX OKAYA R106 Resistor 2.2Ω ±5% 0.25W C102 Capacitor LE104-MX OKAYA R201 Resistor 100kΩ ±5% 0.25W C103 Capacitor 630MPK224K RUBYCON F101 Fuse FIH 2.5A 250V NIPPON-SEISEN C104 Capacitor 630MPK224K RUBYCON VS101 Varistor ERZVEAV471 PANASONIC C105 Capacitor CD70ZU2GA102M TDK VS102 Varistor ERZVEAV471 PANASONIC C201 Capacitor 63ZLJ390M RUBYCON CN101 Connector B2P3-VH JST C202 Capacitor OPEN RUBYCON CN102 Connector B2P-VH JST CN201 Connector B2P-VH JST 1:Adjustment Zenner Diode of OVP 2:Adjustment resistance of output current 3 / 14
Ambient temperature derating curve Max output power[w] Reduce the output power according to the following temperature derating table. 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 200V input 100V input 20 0 20 40 60 80 Ambient temperature[ ] 100V input AC90V~AC169V 200V input AC170V~AC264V CPM3417RA Datasheet Output specifications range Use within the following output specifications range. Output voltage[v] 35 33 31 29 27 25 23 21 19 17 15 380 400 420 440 460 480 500 520 Output current[ma] 4 / 14
Graph of output current - external resistor(theoretical value) Capable of adjusting output current into an arbitrary value by resistance between Pin 11-10 (Synthetic resistance level of R103,104,105) 10 9 8 CPM3417RA Datasheet Resistance value[ω] 7 6 5 4 3 2 1 420 430 440 450 460 470 480 490 500 Output current[ma] External resistor can be connected to the nearest between the pins. Set the output current in the range of 400mA - 500mA. External resistance of less than 2.2Ω must not be connected. Graph of overvoltage protection - external zenner diode(theoretical value) Capable of adjusting overvoltage protection by connecting zenner diode between Pin1-2. 50 Overvoltage protection[v] 45 40 35 30 25 20 20 25 30 35 40 Zener voltage [V] Do not connect zenner diode less than 20V because it may not start. 5 / 14
Typical characteristics Measured by the input frequency 50Hz Io=400mA (Default) 440 430 420 Output Current[mA] 410 400 390 380 370 Output current-line regulation Vo=34V Vo=17V Ta= 20 Ta=+25 Ta=+60 Output Current[mA] 440 430 420 410 400 390 380 370 Ta= 20 Ta=+25 Ta=+60 360 360 Io=500mA (Setting) 550 540 530 Vo=34V Vo=17V Ta= 20 Ta=+25 Ta=+60 550 540 530 Ta= 20 Ta=+25 Ta=+60 Output Current[mA] 520 510 500 490 480 Output Current[mA] 520 510 500 490 480 470 470 460 460 450 450 6 / 14
Typical characteristics Measured by the input frequency 50Hz Efficiency characteristic (Ta=25 ) Io=400mA (Default) 100 Power factor characteristic (Ta=25 ) Io=400mA (Default) 1.00 95 0.95 90 Efficiency [%] 85 80 75 70 Power factor 0.90 0.85 0.80 65 Vo=34V Vo=17V 0.75 Vo=34V Vo=17V 60 0.70 Io=500mA (Setting) 100 Io=500mA (Setting) 1.00 95 0.95 90 Efficiency [%] 85 80 75 70 Power factor 0.90 0.85 0.80 65 Vo=34V Vo=17V 0.75 Vo=34V Vo=17V 60 0.70 7 / 14
Typical characteristics Measured by the input frequency 50Hz Output current ratio [%] 100 90 80 70 60 50 40 30 20 10 0 PWM dimming characteristic (Ta=25 ) AC100V AC240V 0 10 20 30 40 50 60 70 80 90 100 Input Duty [%] Output current ratio [%] LINEAR dimming characteristic (Ta=25 ) 100 AC100V 90 AC240V 80 70 60 50 40 30 20 10 0 0.7 1 1.3 1.6 1.9 2.2 2.5 Input Voltage [V] 8 / 14
Outline dimensional drawing Unit:mm 9 / 14
Recommended hole diameter and land size The round pulling out figure is a pin numbering. Component side Unit:mm Terminal function and connection Pin No. Name Explanation of terminals 1 OVP(A) OVP detection terminal(a) 2 OVP(K) OVP detection terminal(k) 3 No terminal 4 No terminal 5 Io(-) Output terminal (-) Secondaries 6 Io(+) Output1 terminal (+) Secondaries 7 SecW Non-contact terminal Don't connect with other circuits. Secondaries Pin No. Name Explanation of terminals 8 DIM Dimming signal input terminal 9 VccW Non-contact terminal 10 Vin(-) Input terminal (-) 11 Iset Constant current setting terminal 12 Vin(+) Input terminal (+) 13 No terminal 14 Drain Non-contact terminal Don't connect with other circuits. 10 / 14
Application circuit example Parts structure Symbol Description Part No. Manufacturer Symbol Description Part No. Manufacturer L101 Inductor LF4ZTM-E333 KORIN R101 Resistor 1MΩ ±5% 0.25W L102 Inductor PI10a-471K KORIN R102 Resistor 1MΩ ±5% 0.25W L201 Inductor 0-5127-15 KORIN R103 2 Resistor OPEN D101 Diode S1NBC80 SHINDENGEN R104 2 Resistor OPEN D201 1 OPEN R105 2 Resistor OPEN C101 Capacitor LE104-MX OKAYA R106 Resistor 2.2Ω ±5% 0.25W C102 Capacitor LE104-MX OKAYA R201 Resistor 100kΩ ±5% 0.25W C103 Capacitor 630MPK224K RUBYCON F101 Fuse FIH 2.5A 250V NIPPON-SEISEN C104 Capacitor 630MPK224K RUBYCON CN101 Connector B2P3-VH JST C105 Capacitor CD70ZU2GA102M TDK CN201 Connector B2P-VH JST C201 Capacitor 63ZLJ390M RUBYCON VS101 Varistor ERZVEAV471 PANASONIC C202 Capacitor OPEN RUBYCON VS102 Varistor ERZVEAV471 PANASONIC 1:Adjustment Zenner Diode of OVP 2:Adjustment resistance of output current 11 / 14
Application circuit example PWM dimming_insulation type Parts structure For PWM dimming Symbol Description Part No. Manufacturer Symbol Description Part No. Manufacturer L101 Inductor LF4ZTM-E333 KORIN R101 Resistor 1MΩ ±5% 0.25W L102 Inductor PI10a-471K KORIN R102 Resistor 1MΩ ±5% 0.25W L201 Inductor 0-5127-15 KORIN R103 2 Resistor OPEN D101 Diode S1NBC80 SHINDENGEN R104 2 Resistor OPEN D102 Diode CRF02 TOSHIBA R105 2 Resistor OPEN D103 Diode UDZV4.7B ROHM R106 Resistor 2.2Ω ±5% 0.25W D201 1 OPEN R107 Resistor 510kΩ ±5% C101 Capacitor LE104-MX OKAYA R108 Resistor 510kΩ ±5% C102 Capacitor LE104-MX OKAYA R109 Resistor 510kΩ ±5% C103 Capacitor 630MPK224K RUBYCON R110 Resistor 22kΩ ±5% C104 Capacitor 630MPK224K RUBYCON R111 Resistor 1kΩ ±5% C105 Capacitor CD70ZU2GA102M TDK F101 Fuse FIH 2.5A 250V NIPPON-SEISEN C106 Capacitor GRM31MR71H105K MURATA VS101 Varistor ERZVEAV471 PANASONIC C201 Capacitor 63ZLJ390M RUBYCON VS102 Varistor ERZVEAV471 PANASONIC C202 Capacitor OPEN RUBYCON CN101 Connector B2P3-VH JST PHC101 Photocoupler TLP2301 TOSHIBA CN102 Connector B2P3-VH JST CN201 Connector B2P-VH JST 1:Adjustment Zenner Diode of OVP 2:Adjustment resistance of output current Mount the fuse on the input Live side to ensure safety without fail. Recommended parts:fih 250V 1.6A~2.5A / NIPPON-SEISEN Depend on the applying safety standard, please add the discharge resistance in paralell with C101. Start-up should be avoided in the state focused dimming (at AC100V). Start-up time is longer, or start-up failure is a concern. 12 / 14
Usage cautions Always mount fuse on the Live side of input for ensuring safety because the fuse is not built-in the product. Please select the fuse considering conditions such as steady current, inrush current, and ambient temperature at your responsibility. Recommended parts: FIH 250V 1.6A~2.5A / NIPPON-SEISEN Do not use of connecting the input side to the dimmer. Important notice The content of this document is subject to change without prior notice for the purpose of improvements, etc. Ensure that you are in possession of the most up-to-date information when using this product. The operation examples and circuit examples shown in this document are for reference purposes only, and TAMURA Corporation disclaims all responsibility for any violations of industrial property rights, intellectual property rights and any other rights owned by TAMURA Corporation or third parties that these may entail. The circuit examples and part constants listed in this document are provided as reference for the verification of characteristics. You are to perform design, verification, and judgment at your own responsibility, taking into account the various conditions. TAMURA Corporation constantly strives to improve quality and reliability, but malfunction or failures are bound to occur with some probability in power products. To ensure that failures do not cause accidents resulting in injury or death, fire accidents, social damage, and so on, you are to thoroughly verify the safety of their designs in devices and/or systems, at your own responsibility. This product is intended for use in LED lighting equipment. If considering use of this product in equipment or devices that require high reliability (medical devices, transportation equipment, traffic signal control equipment, fire and crime prevention equipment, aeronautics and space devices, nuclear power control, fuel control, in-vehicle equipment, safety devices, and so on), please consult a TAMURA sales representative in advance. Do not use this product for such applications without written permission from TAMURA Corporation. This product is intended for use in environments where consumer electronics are commonly used. It is not designed for use in special environments such as listed below, and if such use is considered, you are to perform thorough safety and reliability checks at your own responsibility. Use in liquids such as water, oil, chemical solutions, or organic solvents, and use in locations where the product will be exposed to such liquids. Use that involves exposure to direct sunlight, outdoor exposure, or dusty conditions. Use in locations where corrosive gases such as salt air, C12, H2S, NH3, SO2, or NO2, are present. Use in environments with strong static electricity or electromagnetic radiation. Use that involves placing inflammable material next to the product. Use of this product either sealed with a resin filling or coated with resin. Use of water or a water soluble detergent for flux cleaning. Use in locations where condensation is liable to occur. This product is not designed to resist radiation. 13 / 14
This product is not designed to be connected in series or parallel. Do not operate this product in a series, parallel, or N+1 redundant configuration. Do not use or otherwise make available the TAMURA products or the technology described in this document for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of mass destruction weapons (e.g. nuclear, chemical, or biological weapons or missile technology products). When exporting and re-exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations including, without limitation, Japan -Foreign Exchange and Foreign Trade Control Law and U.S.- Export Administration Regulations. The TAMURA products and related technology should not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. Please contact your TAMURA sales office for details as to environmental matters such as the RoHS compatibility of product. Please use TAMURA products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TAMURA assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. TAMURA assumes no liability for damages or losses incurred by you or third parties as a result of unauthorized use of TAMURA products. This document and any information herein may not be reproduced in whole or in part without prior written permission from TAMURA. 14 / 14