RS2012 Low Power OFF-Line SMPS Primary Switcher

Similar documents
AP8012 OFF LINE SMPS PRIMARY SWITCHER GREEN POWER

AP8022. AiT Semiconductor Inc. APPLICATION ORDERING INFORMATION TYPICAL APPLICATION

EM8631S. Green mode PWM Flyback Controller. Features. General Description. Ordering Information. Applications. Typical Application Circuit

VCC. UVLO internal bias & Vref. Vref OK. PWM Comparator. + + Ramp from Oscillator GND

LD7552. Green-Mode PWM Controller. Features. General Description. Applications. Typical Application 2/21/2005

UNISONIC TECHNOLOGIES CO., LTD UCSR3651S Preliminary CMOS IC

Green mode PWM Flyback Controller with External Over Temperature Protection

FSL106HR Green Mode Fairchild Power Switch (FPS )

LD7552B 1/2/2008. Green-Mode PWM Controller with Integrated Protections. General Description. Features. Applications. Typical Application. Rev.

Green-Mode PWM Controller with Hiccup Protection

Green-Mode PWM Controller with Integrated Protections

Green-Mode PWM Controller with Hiccup Protection

LD7523 6/16/2009. Smart Green-Mode PWM Controller with Multiple Protections. General Description. Features. Applications. Typical Application REV: 00

Green-Mode PWM Controller with Hiccup Protection

GGD484X CURRENT MODE PWM CONTROLLER WITH BUILT-IN HIGH VOLTAGE MOSFET

EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at ore.hu.

TS19701A CC/CV Primary-Side PWM Controller

CURRENT MODE PWM+PFM CONTROLLER WITH BUILT-IN HIGH VOLTAGE MOSFET

LD7536R 05/11/2010. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. General Description. Features.

TS19702 High Power Factor Corrector LED Driver

LD7577 1/15/2009. High Voltage Green-Mode PWM Controller with Brown-Out Protection. General Description. Features. Applications. Typical Application

SD4840/4841/4842/4843/4844

For buy, please contact: FEATURES C3 R3 MT MT7990 VDD DRAIN

WS3254 Product Description

LD /15/2011. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. Features. General Description.

DP9126IX. Non-Isolated Buck APFC Offline LED Power Switch FEATURES GENERAL DESCRIPTION APPLICATIONS TYPICAL APPLICATION CIRCUIT

Preliminary GR1230R. Multi-Mode PWM Controller with Integrated Protections. Features. Description. Applications. Typical Application Information

Current Mode PWM Power Switch GR8935L XXXXX

Green-Mode PWM Controller with Integrated Protections

RS431 Series Adjustable Precision Shunt Regulator

KA5x0365RN-SERIES. KA5M0365RN, KA5L0365RN Fairchild Power Switch(FPS) Features. Description. Applications. Internal Block Diagram

DP2539M TYPICAL APPLICATION GENERAL DESCRIPTION FEATURES APPLICATIONS /9 REV1.0

UNISONIC TECHNOLOGIES CO., LTD UC1103 Preliminary CMOS IC

WS3256 Product Description

CR6842. Green-Power PWM Controller with Freq. Jittering. Features. Applications. General Description. Leading-edge blanking on Sense input

DP2537X High Precision CC/CV Primary-Side PWM Power Switch

FSQ510, FSQ510H, and FSQ510M Green Mode Fairchild Power Switch (FPS ) for Valley Switching Converter Low EMI and High Efficiency

FSDM311A Green Mode Fairchild Power Switch (FPS )

LD7536E 5/28/2012. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. General Description. Features.

Green-Mode PWM Controller with Integrated Protections

FSFR-XS Series Fairchild Power Switch (FPS ) for Half-Bridge Resonant Converters

G1102 High Precision CC/CV Primary-Side PWM Controller

PRIMARY SIDE POWER CONTROLLER WITH BUILT-IN HIGH VOLTAGE MOSFET

FSGM300N Green-Mode Fairchild Power Switch (FPS )

Current Mode PWM Power Switch. Code A B G H I J Year Code A B C Month Jan. Feb. Mar. Apr.

DP9122 Non-isolated Quasi-Resonant Buck LED Power Switch

IS31LT3932 HIGH PF LOW THD UNIVERSAL LED DRIVER. December 2013

FSD156MRBN Green-Mode Fairchild Power Switch (FPS )

Preliminary GR8875N Series

DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit

FSL306LR Green Mode Fairchild Buck Switch

CURRENT MODE PWM+PFM CONTROLLER WITH BUILT-IN HIGH VOLTAGE MOSFET. Hazardous Part No. Package Marking

LD9704R 03/15/2017. Green-Mode PWM Controller with Frequency Swapping with protections and MOSFET Integrated. General Description.

SG40N04S 40V N-CHANNEL POWER MOSFET

SP6853 Green-Mode PWM Controller

For buy, please contact: FEATURES MT7845. Drain DSEN. Drain VDD GND COMP

LD7550-B. Green-Mode PWM Controller. General Description. Features. Applications. Typical Application 01/03/2005 LD7550-B

WS3252 Product Description

NIKO-SEM N3860V N3860P REV: A CURRENT MODE PWM CONTROLLER GENERAL DESCRIPTION FEATURES DEVICE SELECTION GUIDE

RS1117 Series 1.0A Low Dropout Positive Voltage Regulator

FSFA2100 Fairchild Power Switch (FPS ) for Half-Bridge PWM Converters

FEATURES MT7845. Drain DSEN. Drain VDD GND COMP

DNP015 Green Mode Fairchild Power Switch (FPS )

UNISONIC TECHNOLOGIES CO., LTD UPSR104 Preliminary CMOS IC

FSDM311. Green Mode Fairchild Power Switch (FPS TM ) Features. Typical Circuit. Applications. Description.

GENERAL DESCRIPTION APPLICATIONS

Not Recommended. TS19702 High Power Factor Corrector LED Driver. Description. Features. Application. Ordering Information

CR6853. Novel Low Cost Green-Power PWM Controller With Low EMI Technique

Single-Stage PFC Buck Current Control LED Driver With High Voltage MOSFET Integrated

Preliminary GL8211/11B

LD7752B 6/11/2013. Green-Mode PWM Controller with HV Start-Up Circuit and Soft Start time Adjustment. Features. General Description.

Green-Mode PWM Controller with Integrated Protections

FSQ0765RS Green-Mode Fairchild Power Switch (FPS ) for Quasi-Resonant Operation - Low EMI and High Efficiency

LD /14/2013. Green-Mode PWM Controller with HV Start-Up Circuit and Soft Start time Adjustment. Features. General Description.

LD7531 6/25/2008. Green-Mode PWM Controller with Frequency Trembling and Integrated Protections. Features. General Description.

FEATURES DESCRIPTION APPLICATIONS. Typical Application Circuit. Vin_ac

FEATURES. Rst1 R Rst2 C2 R2

FSDM311. Green Mode Fairchild Power Switch (FPS TM ) Features. Applications. Typical Circuit. Related Application Notes.

Primary-Side Regulation PWM Controller for PFC LED Driver

SP6853 Green-Mode PWM Controller

IS31LT3916. Isolated or Non-isolated configuration LED driver with active PFC. January General Description. Features

FSFA2100 Fairchild Power Switch (FPS ) for Half-Bridge PWM Converters

FSGM0465R Green-Mode Fairchild Power Switch (FPS )

DESCRIPTION FEATURES PROTECTION FEATURES APPLICATIONS. RS2320 High Accurate Non-Isolated Buck LED Driver

FSB117H / FSB127H / FSB147H mwsaver Fairchild Power Switch (FPS )

Monolithic Power Switcher for Off-line SMPS. Features

Single-Stage Buck Current Control LED Driver with High Voltage MOSFET Integrated

PN2155 High Performance Current Mode PWM Switch

DP9127. Non-isolated Quasi-Resonant Buck LED Power Switch GENERAL DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION CIRCUIT

Novel Low Cost Green-Power PWM Controller

FSQ0170RNA, FSQ0270RNA, FSQ0370RNA Green Mode Fairchild Power Switch (FPS )

Boost LED Driver for MR16 and AR111 Applications

High Power Factor & Accuracy Constant Current LED Driver

High Accurate non-isolated Buck LED Driver

Quasi-Resonant Flyback PWM Controller

UNISONIC TECHNOLOGIES CO., LTD UC3846 LINEAR INTEGRATED CIRCUIT

FSFR-XS Series Fairchild Power Switch (FPS ) for Half-Bridge Resonant Converters

LD7575 6/16/2008. Green-Mode PWM Controller with High-Voltage Start-Up Circuit. General Description. Features. Applications. Typical Application

HT7L4815 Non-isolation Buck LED Lighting Driver with Active PFC

FSEZ1016A Primary-Side-Regulation PWM Integrated Power MOSFET

Transcription:

Page No.: 1/7 RS2012 Low Power OFF-Line SMPS Primary Switcher The RS2012 combines a dedicated current mode PWM controller with a high voltage Power MOSFET on the same silicon chip. Typical applications cover off line power supplies for battery charger adapters, standby power supplies for TV or monitors, auxiliary supplies for motor control, etc. The internal control circuit offers the following benefits: Large input voltage range on the VCC pin accommodates changes in auxiliary supply voltage. This feature is well adapted to battery charger adapter configurations. Automatic burst mode in low load condition. Over voltage protection in HICCUP mode. Features 85V to 265V wide range AC voltage input A 700V MOSFET on the same silicon chip Auto start up with high voltage current source PWM with current mode control 9V to 38V wide range VCC voltage Fixed 60KHz switching frequency Automatic skip cycle mode in low load condition Over temperature, over current and over voltage protection Auxiliary under voltage lockout with hysteresis Applications Power AC/DC Adapters for Chargers DVD/VCD power supplies Electromagnetic Oven power supplies Air Conditioner power supplies STB power supplies AC/DC LED Driver Applications Pin Configurations TYPE SOP-8L DIP-8L European (195-265 Vac) 8W 13W US (85-265 Vac) 5W 8W Pin Number Pin Name Function Description 1, 2 GND Sense FET source terminal on primary side and internal control ground. 3 COMP Feedback input defines the peak drain MOSFET current. 4 VCC Positive supply voltage input. Although connected to an auxiliary transformer winding, current is supplied from SW via an internal switch during startup (see Internal Block Diagram section). It is not until VCC reaches them UVLO upper threshold (14.5V) that the internal start-up switch opens and device power is supplied via the auxiliary transformer winding. 5, 6, 7, 8 SW The SW pin is designed to connect directly to the primary lead of the transformer and is capable of switching a maximum of 700V.

Page No.: 2/7 Block Diagram Typical Application Circuit

Page No.: 3/7 Absolute Maximum Ratings (Ta=25 C, unless otherwise specified) Symbol Parameter Range Units V SW SW to GND Voltage (T J =25-125 C) -0.3 to 730 V I D Continuous VDMOS Drain Current Internally limited A VCC Supply Voltage 0 to 50 V I COMP Feedback Current 3 ma V ESDMM Electrostatic Discharge: Machine Model (R=0Ω ; C=200pF) 200 V V ESDHBM Electrostatic Discharge: HBM 2000 V T J Junction Operating Temperature Internally limited- T C Case Operating Temperature -40 to +150 T STG Storage Temperature -55 to +150 Electrical Characteristics (Power) Symbol Parameter Conditions Min. Typ. Max. Unit BV DSS VDMOS Breakdown Voltage ID=1mA; VCOMP=2V 730 V I DSS Zero Gate Voltage Drain Current VDS=500V; VCOMP=2V; 100 ua R DSON Static Drain-Source on Resistance VGS=10V ID=0.4A; 27 30 Ω T R Rise Time ID=0.1A; VIN=300V 50 ns T F Fall Time ID=0.2A; VIN=300V 100 ns C OSS VDMOS Drain Capacitance VDS=25V 40 pf Electrical Characteristics (Control) (Ta=25 C, VCC=18V, unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit UVLO SECTION V START VCC Start Threshold Voltage V COMP =0V 13 14.5 16 V V STOP VCC Stop Threshold Voltage V COMP =0V 7 8 9 V V HYS VCC Threshold Hysteresis 5.8 6.5 7.2 V OSCILLATOR SECTION F OSC Initial Accuracy V STOP VCC 35V; 0 T J 100 C 54 60 66 KHz ΔF/ΔT Frequency Change With Temperature -25 C T J +85 C ±5 ±10 % FEEDBACK SECTION I COMP Feedback Shutdown Current T J =25 C, V COMP = 0V 0.9 ma R COMP COMP Pin Input Impedance I D =0mA 1.2 kω CURRENT LIMIT (SELF-PROTECTION) SECTION G ID ICOMP to ID Current Gain 320 I LIM Peak Current Limit T J = 25 C 0.32 0.40 0.48 A T D Current Sense Delay to Turn-Off I D =0.2A 200 ns T B Blanking Time 500 ns T ONMIN Minimum Turn On Time 700 ns PROTECTION SECTION T SD Thermal Shutdown Temperature 140 170 T HYST Thermal Shutdown Hysteresis 40 V OVP Over Voltage Protection 38 42 46 V SUPPLY CURRENT SECTION I CH Startup Charging Current 1 ma I CHOFF Start Up Charging Current in Thermal VCC=5V; V DS =100V Shutdown T J > T SD 0.2 ma I OP0 Operating Supply Current (Control Part Only) Switching V COMP = 0V 4.5 ma I OP1 Operating Supply Current (Control Part Only) Not Switching V COMP = 2V 3 5 ma

Page No.: 4/7 Functional Description 1. Startup This device includes a high voltage start up current source connected on the SW of the device. As soon as a voltage is applied on the input of the converter, this start up current source is activated and to charge the VCC capacitor as long as VCC is lower than VSTART. When reaching VSTART, the start up current source is cut off by UVLO&TSD and the device begins to operate by turning on and off its main power MOSFET. As the COMP pin does not receive any current from the opto-coupler, the device operates at full current capacity and the output voltage rises until reaching the regulation point where the secondary loop begins to send a current in the opto-coupler. At this point, the converter enters a regulated operation where the COMP pin receives the amount of current needed to deliver the right power on secondary side. Fig 1 Startup circuit 2. Feedback A feedback pin controls the operation of the device. Unlike conventional PWM control circuits which use a voltage input, the COMP pin is sensitive to current. Figure 2 presents the internal current mode structure. The Power MOSFET delivers a sense current which is proportional to the main current. R2 receives this current and the current coming from the COMP pin. The voltage across R2 VR2 is then compared to a fixed reference voltage. The MOSFET is switched off when VR2 equals the reference voltage. 3. Leading Edge Blanking (LEB) At the instant the internal Sense FET is turned on, there usually exists a high current spike through the Sense FET, caused by the primary side capacitance and secondary side rectifier diode reverse recovery. Excessive voltage across the sense resistor would lead to false feedback operation in the current mode PWM control. To counter this effect, the device employs a leading edge blanking (LEB) circuit. This circuit inhibits the PWM comparator for a short time (typically 500ns) after the Sense FET is turned on. 4. Under Voltage Lock Out Once fault condition occurs, switching is terminated and the Sense FET remains off. This causes VCC to fall. When VCC reaches the UVLO stop voltage, 8V, the protection is reset and the internal high voltage current source charges the VCC capacitor. When VCC reaches the UVLO start voltage, 14.5V, the device resumes its normal operation. In this manner, the auto-restart can alternately enable and disable the switching of the power Sense FET until the fault condition is eliminated. 5. Thermal Shutdown (TSD) The Sense FET and the control IC are integrated in the same chip, making it easier for the control IC to detect the temperature of the Sense FET. When the temperature exceeds approximately 170 C, thermal shutdown is activated, the device turn off the Sense FET and the high voltage current source to charge VCC. The device will go back to work when the lower threshold temperature about 140 C is reached. 6. Over Voltage Protection (OVP) In case of malfunction in the secondary side feedback circuit, or feedback loop open caused by a defect of solder, the current through the optocoupler transistor becomes almost zero. Because excess energy is provided to the output, the output voltage may exceed the rated voltage, resulting in the breakdown of the devices in the secondary side. In order to prevent this situation, an over voltage protection (OVP) circuit is employed. If VCC exceeds 42V, OVP circuit is activated resulting in termination of the switching operation. In order to avoid undesired activation of OVP during normal operation, VCC should be properly designed to be below 42V.

Page No.: 5/7 SOP-8L Dimension 8-Lead SOP-8L Plastic Surface Mounted Package Package Code: S B A 8 7 6 5 Pin1 Index 2 3 4 D E Part A F C G I H J K Part A M L O N DIM Min. Max. A 4.85 5.10 B 3.85 3.95 C 5.80 6.20 D 1.22 1.32 E 0.37 0.47 F 3.74 3.88 G 1.45 1.65 H 4.80 5.10 I 0.05 0.20 J 0.30 0.70 K 0.19 0.25 L 0.37 0.52 M 0.23 0.28 N 0.08 0.13 O 0.00 0.15 *: Typical, Unit: mm DIP-8 Dimension DIM Min. Max. 8-Lead DIP-8 Plastic Package Package Code: P 8 7 6 5 1 2 3 4 B C E I D A F G H α1 M J K L A 6.29 6.40 B 9.22 9.32 C - *1.52 D - *1.27 E - *0.99 F 3.25 3.35 G 3.17 3.55 H 0.38 0.53 I 2.28 2.79 J 7.49 7.74 K - *3.00 L 8.56 8.81 M 0.229 0.381 α1 94 o 97 o *: Typical, Unit: mm Ordering Information PART NUMBER RS2012S RS2012P PACKAGE SOP-8L DIP-8L

Page No.: 6/7 Soldering Methods for Orister s Products 1. Storage environment: Temperature=10 ~35 Humidity=65%±15% 2. Reflow soldering of surface-mount devices Figure 1: Temperature profile TP Ramp-up tp Critical Zone TL to TP TL Tsmax tl Temperature Tsmin ts Preheat Ramp-down 25 t 25 to Peak Time Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly Average ramp-up rate (T L to T P ) <3 /sec <3 /sec Preheat - Temperature Min (Ts min ) - Temperature Max (Ts max ) - Time (min to max) (ts) 100 150 60~120 sec 150 200 60~180 sec Tsmax to T L - Ramp-up Rate <3 /sec <3 /sec Time maintained above: - Temperature (T L ) - Time (t L ) 183 60~150 sec 217 60~150 sec Peak Temperature (T P ) 240 +0/-5 260 +0/-5 Time within 5 of actual Peak Temperature (t P ) 10~30 sec 20~40 sec Ramp-down Rate <6 /sec <6 /sec Time 25 to Peak Temperature <6 minutes <8 minutes 3. Flow (wave) soldering (solder dipping) Products Peak temperature Dipping time Pb devices. 245 ±5 5sec ±1sec Pb-Free devices. 260 +0/-5 5sec ±1sec

Page No.: 7/7 Important Notice: All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of Orister Corporation. Orister Corporation reserves the right to make changes to its products without notice. Orister Corporation products are not warranted to be suitable for use in Life-Support Applications, or systems. Orister Corporation assumes no liability for any consequence of customer product design, infringement of patents, or application assistance.