INSTALLATION INSTRUCTIONS WL WL1 WL WL WL9 WL10 WL5 WL6 WL7 WL8 Wall and Pole Mounted, Static and Swing Arm Mounts MSPWL SERIES
MSPWL SERIES DISCLAIMER Milestone AV Technologies, Inc., and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Chief and Centris are trademarks of Milestone AV Technologies, Inc. All rights reserved. Installation Instructions Maximum Capacity By Model MODEL Max Weight LBS Max Weight KG WL1 0 LBS 1.61 kg WL LBS (16.5 per side) 15 kg (7.8 per side) WL 0 LBS 18.1 kg WL LBS (16.5 per monitor) 15 kg (7.8 per monitor) WL5 5 LBS 15.87 kg WL6 70 LBS (5 per monitor) 1.75 kg (15.87 per monitor) WL7 LBS (16.5 per monitor) 15 kg (7.8 per monitor) WL8 LBS (16.5 per monitor) 15 kg (7.8 per monitor) WL9 5 LBS 11. kg WL10 0 LBS (0 per monitor) 18.1 kg (9.10 per monitor) IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. For additional information pertaining to available accessories contact a Chief Customer Service represenatative. Dimensions Detailed technical drawings for all models can be obtained by contacting a Chief Customer Service Representative. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided. WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer s responsibility to make sure the combined weight of all components located between the supporting structure and mount does not exceed the weights specified for each model in the following table.
Installation Instructions MSPWL SERIES LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis à pointe cruciforme Open-Ended Wrench Llave de boca Gabelschlüssel Chave de bocas Chiave a punte aperte Steeksleutel Clé à fourche By Hand A mano Von Hand Com a mão A mano Met de hand À la main Hex-Head Wrench Llave de cabeza hexagonal Sechskantschlüssel Chave de cabeça sextavada Chiave esagonale Zeskantsleutel Clé à tête hexagonale Pencil Mark Marcar con lápiz Stiftmarkierung Marcar com lápis Segno a matita Potloodmerkteken Marquage au crayon Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez Optional Opcional Optional Opcional Opzionale Optie En option Security Wrench Llave de seguridad Sicherheitsschlüssel Chave de segurança Chiave di sicurezza Veiligheidssleutel Clé de sécurité
MSPWL SERIES Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1/" 9/16" /" 1/8" 5/" (Included) /16" PARTS A B F C D E X G H L Y M1 M M5 K N P M M Q M AA R S T U V BB W1 W W W W W5 W6 CC DD EE FF HH.0 x.56 x.018" UHMW GG 5/16-18 I I
Installation Instructions MSPWL SERIES PARTS (CONTINUED) Carefully inspect components for shipping damage. If damage is apparent, call your carrier claims agent and do not continue with installation until the carrier has reviewed the damage. Table 1: Parts QUANTITY By MODEL ITEM DESCRIPTION WL1 WL WL WL WL5 WL6 WL7 WL8 WL9 WL10 A PIPE CAP, 1.75 OD - - - - 1 1 1 1 - - B KEY, Hex, 1/8" (Provided with mount) 1 1 1 1 - - - - 1 1 C KEY, Hex, /16" (Provided with mount) 1 1 1 1 1 1 1 1 1 1 D KEY, Hex, 5/" (Provided with mount) 1 1 1 1 1 1 1 1 1 1 E Centris Head Assembly, Array 1 1 - - - - F Arm Assembly, Dual Static Arm, 7" Vertical Array 1 - - - - - - - - - G Arm Assembly, Dual Static Arm, Vertical Array - 1 - - - - - - - - H Arm Assembly, Dual Static Arm, Vertical Array - - - 1 - - - - - - X Vertical Array, Single - - 1 - - - - - - - Bracket, Swing Arm Mounting 1 1 1 1 - - - - 1 1 K Centris Head Assembly, Pole Mount - - - - 1 - - - - L Arm Assembly, Dual Static Arm, Array - - - - - - 1 1 - - M Kit, Array Hardware (Includes M1 through M5) 1 1 1 1 M1 Screw, Phillips Pan Head, M x 1mm 8 8 8 8 8 8 M Screw Phillips Pan Head, M x 0mm 8 8 8 8 8 8 M Screw, Phillips Pan Head, M x 0mm 8 8 8 8 8 8 M Spacer, Nylon, 1/" x /8" 8 8 8 8 8 8 M5 Spacer, Nylon, 1/" x /" 8 8 8 8 8 8 N Clamp, Back, Array mounting - - - - 1 1 1 - - P Grommet, Pole Installation - - - - 1 1 1 1 - - Q Bracket, Grommet Installation - - - - 1 1 1 1 - - R Sheath, Cable, 8" - - - - 1 - - S Pole, 1" - - - - - - 1 - - - T Pole, 8" - - - - 1 1-1 - - U Screw, Button Head Cap, 1/-0 x /" - - - - 6 - - V Screw, Hex Head Tap Bolt, /8-16 x 6" Pole Mounting - - - - 1 1 1 1 - - W Kit, Installation, Swing Arm Array (Includes w1 through w6) 1 1-1 - - 1 1 - - W1 Cover, Cable Management - - - 1 W Screw, Button Head Cap, 1/-0 x 1/" - - - - W Screw, Phillips Undercut Machine, 8- x /8" - - - W Lock, End, 1/-0 - - - - W5 Clip, Cable Management (not shown) - - - W6 Tie, Cable, /" (not shown) - - - Y Plate, Wall, Dual Swing Arm Mounting - - - - - - - - - 1 AA Arm Assembly, Swing Arm, Height Adjustable - - - - - - - - 1 - BB Arm Assembly, Dual Swing Arm, Height Adjustable - - - - - - - - - CC Screw, Button head cap - - - - - - - - - DD Washer, Flat,.0 x.56 x.018 - - - - - - - - - EE Washer, Flat - - - - - - - - - FF Washer Flat, UHMW - - - - - - - - - GG Pin, Pivot - - - - - - - - - HH Nut, Hex, 5/16-18 - - - - - - - - - I I KEY, Hex, /" (Provided with mount) - - - - - - - - 1-5
MSPWL SERIES INSTALLATION Installation Instructions 5. Tighten two upper and lower button head cap screws to secure wall bracket () to wall. (See Figure ) WARNING: FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS COMPONENT CAN RESULT IN SERIOUS PERSONAL INURY OR DAMAGE TO EQUIPMENT! It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. 5 x Wall Mount Installation (Applies to Models WL1, WL, WL, and WL, WL9 and WL10) 1. Verify mounting brackets on wall bracket () can move freely. (See Figure 1) 5 1 x Figure IMPORTANT! : If the display being installed has a recessed mounting surface, the display must be assembled to the mount prior to mount installation. See Display Installation in this document before proceeding. 6. Insert top of mount (F, G, H, Y, AA) over lip on top of wall bracket (). (See Figure ) Figure 1. Locate desired installation location and slide upper mounting plate into wall making sure bracket is seated in channel bottom. (See Figure ). Let lower mounting plate rest against wall.. Using 1/" socket, tighten tension hex head bolt until lower mounting plate slides into channel in wall and continue tightening until resistance is felt. (See Figure ) F, G, H, Y, AA 6 Figure 7. Swing mount (F, G, H, Y, AA) down flush against wall bracket (). (See Figure 5) Figure 6
Installation Instructions MSPWL SERIES F, G, H, Y, AA 8 F, G, H, Y, AA Figure 5 8. Tighten set screw using 5/" hex key. (See Figure 6) CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INURY OR DAMAGE TO EQUIPMENT! Make sure set screw engages back side of mounting dish on wall bracket (). (See Figure 6) 7 Figure 6 Dual Swing Arm Installation ( Model WL10 Only) 1. Insert pivot pin (GG) into Y-connector upper bore.. Install spacer (EE). (See Figure 7). Insert arm assembly (BB) on pivot pin (GG).. While holding nut (HH) in lower bore of Y-connector, insert screw (CC) through washers (DD), UHMW washer (FF), arm assembly (BB), spacer (EE) and Y-connector, into nut (HH). (See Figure 7) 5. Loosely install screw (CC) using /16" hex key. 6. Repeat Steps 1. through 5. for second swing arm assembly (BB). (CC) X (FF) X 5 (BB) X (DD) X (EE) X (GG) X 1 (HH) X Figure 7 7
MSPWL SERIES Installation Instructions Pole Mount Installation (Applies to Models WL5, WL6, WL7, and WL8) IMPORTANT! : If the display being installed has a recessed mounting surface, the display must be assembled to the mount prior to mount installation. See Display Installation in this document before proceeding. K or L 8 WARNING: ELECTRICAL SHOCK HAZARD! Drilling into electrical wires and cables can cause DEATH or SERIOUS PERSONAL INURY! ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling. 5 N U x WARNING: EXPLOSION AND FIRE HAZARD! Drilling into gas plumbing can cause DEATH or SERIOUS PERSONAL INURY! ALWAYS make certain area behind mounting surfaces is free of gas, water, waste, or any other plumbing before drilling. 1. Determine approximate location for mount keeping in mind display size, extension, height adjustment (if applicable), and pitch/roll requirements.. Mark installation location and drill one.00" - 1.00" dia. pilot hole through mounting surface. (See Figure 8). Position grommet mounting bracket (Q) underneath mounting surface and grommet (P) on top of mounting surface and align mounting holes with pilot hole. (See Figure 8). Align mounting hole in bottom of pole (S or T) with mounting hole in grommet (P) and secure to mounting surface using one /8" x 6" hex head bolt (V). (See Figure 8) S, T Figure 9 5. Place mount (K or L) against pole (S or T), with back clamp (N) on opposite side of pole (K or L). (See Figure 9) 6. Loosely assemble mount (K or L) to back clamp (N) using 5/" hex wrench (D) and three screws (U). (See Figure 9) NOTE: Equally tighten screws (U) against mount (K or L) and the back clamp (N). (See Figure 10) Keep equal distance between mount and clamp when tightening. (N) (U) x (K) or (L) P 1/" (Ø1mm) x1 Figure 10 7. Position mount at desired height and orientation. 8. Tighten three screws (U) using 5/" hex wrench (D). (See Figure 9) 9. Add pipe cap (A) to top of pole (S or T). Q V x1 1 DISPLAY INSTALLATION The mounting holes on the back of the display will be flush with the back surface, or recessed into the back. Refer to the applicable installation procedure below. Swing Arm Flush Display Installation Figure 8 IMPORTANT! : If the display being installed has a recessed mounting surface, the display must be assembled to the mount prior to mount installation. See Display Installation in this document before proceeding. CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mounting holes. 8
Installation Instructions MSPWL SERIES CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INURY OR DAMAGE TO EQUIPMENT! Inadequate thread engagement in display may cause display to fall! Back out screws ONLY as necessary to allow installation of Centris bracket! 1. Ensure Centris cup is able to swivel and tilt easily, yet still be tight enough to hold display in desired position. Adjust as required before proceeding. See "ADUSTMENT" for detail.. Using Phillips screwdriver, carefully install two screws (M1) into the upper mounting holes on the display. Thread screws completely into display, then back out complete turns.. Align two screws (M1) (installed on the back of the display in the previous step) with the two top teardrop mounting holes on the Centris cup. CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INURY OR DAMAGE TO EQUIPMENT! Smaller area of teardrop mounting holes must be facing downward for proper installation. Reposition Centris cup if required. M1 x Centris Cup Figure 11. Using Phillips screwdriver, install two screws (M1) through the lower mounting holes in Centris cup into the display. 5. Tighten all screws (M1). Do not overtighten! M1 x Figure 1 6. Repeat Steps 1-6 for second display if required. 7. Proceed to "CABLE MANAGEMENT." Swing Arm Recessed Display Installation 1. Ensure Centris bracket is able to swivel and tilt easily, yet still be tight enough to hold display in desired position. Adjust as required before proceeding. See "ADUSTMENT" for detail.. Carefully place display face down on a clean and dry surface.. Determine depth of recessed mounting holes relative to back surface of display.. Select proper length spacer and screw from table below: IMPORTANT! : All spacers used should be the same length. If the recess depths result in multiple spacer lengths, then select the longer spacer. IF recess DEPTH is: THEN use spacer: AND screw: /8" or less M (/8" long) M (M x 0mm) More than /8" up to and including /" M5 (/" long) Centris Cup M (M x 0mm) 5. Place the four (M or M5) spacers over each mounting hole on the back of display. (See Figure 1) 6. Orient mount so that mounting holes in the Centris cup are aligned with the holes in the spacers (M or M5); rotate the Centris cup as required (See Figure 1). CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mounting holes. 7. Using Phillips screwdriver, install four screws (M or M) through the mounting holes in Centris cup, through the spacers (M or M5), into display (See Figure 1). 8. Tighten all four screws. Do not overtighten! 9. Return to appropriate mount installation section to continue. 9
MSPWL SERIES Installation Instructions Centris Cup 7 M or M ( places) M or M5 ( places) M1, M or M ( places) 6 M or M5 ( places) E Figure 1 Array Flush and Recessed Display Installation CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mounting holes. Figure 1 5. Slide display with Centris assembly (E) onto array rail. (See Figure 15) 6. Repeat previous steps for each additional display. CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INURY OR DAMAGE TO EQUIPMENT! Inadequate thread engagement in display may cause display to fall! Back out screws ONLY as necessary to allow installation of Centris bracket! 1. Place display face down on a clean dry surface.. If display being installed has a recessed mounting surface place one /8" or /" nylon spacers (M or M5) over each of the four mounting holes in display back (See Figure 1).. Align Centris cup mounting holes on Centris head assembly (E) with four nylon spacers (M or M5) (See Figure 1).. Secure Centris head assembly (E) to display using four screws (M1, M or M). M and M are used with M and M5 spacers. (See Figure 1). (Display shown removed for clarity) 5 Figure 15 7. Install end lock (W) into square nut (W) in mounting rail using the 5/" hex wrench (D). (See Figure 16) W 7 W Figure 16 10
Installation Instructions Cable Management Swing Arm Models WL1, WL, WL, WL, WL7, WL8 Option A 1. Connect cables to display.. Route cables through cable management clips on array rail and down towards swing arm. Option B MSPWL SERIES 1. Connect cables to display.. Route cables through cable management clips on array rail and down towards swing arm. Cable Management Clips Cable Management Clips Figure 17. Route cables underneath swing arms.. Secure cable management covers (W1) to swing arms using two screws (W) per cover. Figure 19. Place two cable management covers (W1) upward into swing arms and secure to swing arms using cable clips (W5) and two screws (W) per cover.. Slide cable ties (W6) between cable clips (W5) and cable covers (W1) and route cable under arms. 5. Secure cables to arms by closing cable ties (W6). W1 x W1 x W x W5 x W x W6 x Figure 18 Figure 0 11
MSPWL SERIES Swing Arm Models WL9, WL10 1. Attach all cables to display.. Open the cable management bracket by sliding it towards the edge of the arm (See Figure 1). NOTE: If necessary, cable management bracket attach screws may be loosened using /" hex key (II). Installation Instructions CAUTION: Ensure that adequate cable slack exists for movement of display, and that cables will not be pinched by installation of cover (W1) or screws (W). 5. Carefully insert cables in cavity located in lower portion of mount arm (See Figure ). 6. Using Phillips screwdriver, install cover (W1) with two screws (W). Attach Screws Cable Path (typical) OPEN Position CLOSED Position View from Bottom Figure 1 W1 CAUTION: Ensure that adequate cable slack exists for movement of display, and that cables will not be pinched when bracket is closed.. Carefully insert cables into bracket (See Figure ). W Figure 7. Repeat cable management procedures for second display. Pole Mount Models 1. Connect cables to display.. Route cables through cable management clips on array rail and down pole using sheath (R). (See Figure ) Cable Management Clips Cable Management Bracket (in open position) Cable Path (typical) NOTE: Display not shown for clarity. Figure. Close cable management bracket by sliding it back towards the centerline of the arm (See Figure 1). NOTE: If necessary, cable management bracket attach screws may be tightened using /" hex key (II). Adjustments R Figure Centris Head Tension Adjustment 1. If previously attached, disconnect cables from display, remove display. 1
Installation Instructions MSPWL SERIES. Using Phillips screwdriver, slightly loosen or tighten the adjustment screw as necessary (See Figure 5). Adjustment Screw Figure 5:. Reinstall display. See Display Installation in this document. Display Adjustment Lateral position on display: 1. Using your fingers, slightly loosen adjustment knob "A". (See Figure 6). Slide display to desired position.. Using your fingers, tighten adjustment knob "A". (See Figure 6) PITCH / YAW / ROLL Tension 1. Using your fingers, slightly loosen adjustment knob "B". (See Figure 6). Adjust display as desired.. Using your fingers, tighten adjustment knob "B". Figure 7 A B Figure 6: Swing Arm Tension 1. Using /16" hex wrench (C), loosen or tighten adjustment screw(s) as necessary (See Figure 7). 1
MSPWL SERIES Installation Instructions 1
Installation Instructions MSPWL SERIES 15
MSPWL SERIES Installation Instructions Chief Manufacturing, a products division of Milestone AV Technologies 88-0000 Rev I 010 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 08/10 USA/International A 801 Eagle Creek Parkway, Savage, MN 5578 P 800.58.680 / 95.89.680 F 877.89.6918 / 95.89.6918 Europe A Fellenoord 10 5611 ZB EINDHOVEN, The Netherlands P +1 (0)0 66860 F +1 (0)0 668615 Asia Pacific A Office No. 1 on 1/F, Shatin Galleria 18- Shan Mei Street Fotan, Shatin, Hong Kong P 85 15 099 F 85 15 77