New Product Release Information Vilvoorde 25 February 2011 NX-220 / NX-320 NEXEDGE VHF/UHF Digital & FM Portable Transceiver 12+4 Key / Display 4 Key / Display Simple VHF(136-174MHz) NX-220 E NX-220 E2 NX-220 E3 UHF(400-470MHz) NX-320 E NX-320 E2 NX-320 E3 1. SCHEDULE Mass Production & Launch End of March 2011 1
2. PRICE The prices are not yet finished at this moment. We will communicate them as soon as possible. 3. OVERVIEW Mixed Mode Channel Spacing Enhanced Current Analogue and NXDN digital fleets can share a NEXEDGE base/repeater station in 25, 20 or 12.5 khz Analogue & 12.5 or 6.25 khz NXDN conventional "Mixed Mode," thus providing uninterrupted service as long as needed and a straightforward migration path as aging Analogue fleets are replaced with digital. Also, NEXEDGE trunked traffic channels can be shared with existing external Analogue conventional or trunked logic controllers, extending service to fleets as a transition to NXDN trunking is underway. 12.5 khz/ 6.25 khz Band Width Operation (Digital Mode) The NX-220 / 320 can be used for 12.5 khz (Narrow) or 6.25 khz (Very Narrow) band width operation in NXDN digital mode. 25 khz/ 20 khz / 12.5 khz per Channel (Analogue mode) The NX-220 / 320 can be used for 25 khz (Wide), 20 khz (Semi Wide) or 12.5 khz (Narrow) spacing operation per channel in Analogue mode. OTAP ( new NEXEDGE feature-april 2011 ) OTAP (Over The Air Programming) is a new function to reprogramming NEXEDGE terminals remotely, and can do FPU setting of the terminals over the air. OTAP Management software required to use the OTAP functionality. This new feature will be available and explained later ( End of March 2011) and is also applicable for other NEXEDGE Terminals. Telephone Interconnect ( new Nexedge feature-april 2011) Adding telephone interconnect solution to current NEXEDGE trunked system will require KTI-4 with external telephone patch. Phone calls to the system or outgoing calls to PSTN or PABX will passes through KTI-4, which serves as modulator or demodulator for NEXEDGE digital voice audio and Analogue audio. This new feature will be available and explained later ( End of March 2011) and is also applicable for other NEXEDGE Terminals. STAFF SAFE FUNCTIONS (MAN-DOWN / STATIONARY* / MOTION DETECTION*) Three different staff safe functions are available that make use of the built-in motion sensor. When activated, a mandown alert is generated automatically if the radio is not upright for a length of time. Similarly alerts can be sent if the radio is stationary for a preset period or if it is being shaken/swung violently as when someone is running. *: Enhanced software option. 2
QT/DQT/DTMF/5-TONE The industry standard tone/code squelching formats QT (CTCSS) and DQT (digital) provide system access and group segregation on shared frequencies. DTMF PTT ID is included for dispatch operations or for a simple remote control application. The DTMF decode capabilities include a selective call, transpond and radio stun. 5-Tone encode and decode provides 12 different formats (ZVEI, ZVEI2, PZVEI, DZVEI, PDZVEI, CCIR, PCCIR, EIA, EEA, Natel, AP-369, Kenwood format) for selective call use. All selective calling formats(fleetsync, DTMF & 5-Tone) have call alert tones and LED indications. MDC-1200 signalling Built-in MDC signalling added that the following features are available: PTT ID Encode /Decode Emergency Encode/Decode Stun/Revive Decode Radio Check Decode MPT1327 trunked operation (Future Availability Summer 2011) NEXEDGE series will support MPT1327 trunking operation. From small groups to large scale of fleets, Kenwood s MPT radios provide reliable communications over MPT trunking networks. Flexible PC-settings allows easy and quick setting up. (Also applicable for other NEXEDGE Terminals. ) Multiple Solutions One System NX-220 / 320 use advanced DSP-driven digital voice technologies and support both FM Analogue and new digital fleets. System type conversion or expansion only requires software options and/or additional base station units, i.e., no major hardware upgrading. Kenwood offers NEXEDGE conventional, trunked and wide area trunked IP network solutions with secure digital voice and an array of advanced digital feature sets for business and government sectors. (Also applicable for other NEXEDGE Terminals in April 2011 via a new NEXEDGE-Firmware release. ) Meet Analogue & Digital ETSI European Standard R&TTE Standard: EN 300 086, EN 300 113, EN 300 219, EN301 489, EN 301 166 (Voice & Data for 6.25 khz Digital) Safety Standard: EN 60065, EN 60950-1, EN 60215 Extended Range over Analogue communication As RF signal strength weakens with distance, FM Analogue reception becomes increasingly noisy and intermittent. NXDN 's low BER improves reception in fringe areas, thereby increasing the effective range generally by as much as twenty percent over Analogue FM. Natural Sounding Digital Voice plus Enhanced Kenwood Audio The AMBE+2 VOCODER, a state-of-the-art voice digitization technology, replicates an individual's natural human speech nuances accurately unlike early technologies that sounded unnatural and synthesized. The AMBE+2 offers superior voice quality at varying signal strengths even while driving at motorway speeds. In addition to this technology, Kenwood utilizes its long standing audio heritage to optimize voice frequency components so that the audio output cuts through typical ambient noise. This enhancement and the noise reduction also provide clarity and low distortion in FM Analogue mode. Secure Voice & Data NEXEDGE offers voice security for personnel safety and reduced liability exposure by 3
protecting sensitive communications for your facilities and operations. Inherent Level of Security in Digital Mode NXDN digital air interface prevents casual eavesdropping. Furthermore, the built-in NXDN Digital Scrambler allows more secure Voice & Data communication. Voice Inversion Scrambler Built-in The built-in Analogue voice inversion scrambler provides basic communications protection against casual eavesdropping. General Features 260ch for display model / 64ch for Non display model VHF(136-174MHz), UHF(400-470MHz) wideband coverage GPS ready for the KMC-48GPS IP-54/55 Water & Dust Intrusion, MIL-STD-810 C/D/E/F/G 2 Pin Accessory Connector Compatible with existing battery and charger (KNB-55L/56N/57L, KSC-25/256) Low Battery Alert Emergency/AUX Key Flash Firmware Upgrading VOX Ready On/Off Volume Knob Transmit/Busy/Call Alert/Warn LED 2 Side PF Keys + Orange Key Time Out Timer 500 mw Speaker Audio LCD Battery Status Indicator* Emergency Call Features Battery Saver Special Alert Tone Patterns Lone Worker Busy Channel Lockout KPG-141D Windows FPU Transparent Data Mode Programmable TX/RX Indication (On/Off) MIL-Spec Speaker Mic Options No option board capability *: LED Battery Status Indicator on the NX-220E3/320E3 DIGITAL GENERAL NXDN Digital Air Interface AMBE+2 VOCODER 6.25 & 12.5 khz Channels Over-the- Air Alias (TX) Emergency Call Short & Long Data Messages *1 NXDN Scrambler Status Messaging*1, *2 Remote Stun/Kill *1 GPS Location with Voice *1 *1: Requires NX subscriber unit PC Serial Interface compatible software application (e.g Kenwood AVL & Dispatch Messaging software) or hardware (e.g. console). *2: Can be used by pre-programmed key operation on the NX-220E3/320E3 DIGITAL CONVENTIONAL MODE 64 (including none ) Radio Access Numbers (RAN) Individual & Group Selective Call* Mixed FM/Digital Operation Conventional IP Networks Site Roaming * Some screen/key-based functions not available on the NX-220E3/320E3 DIGITAL TRUNKING MODE Individual Private Call*1 Group Call 4 Priority Monitor ID s *2 Late Entry (UID & GID) *2 Broadcast Call Remote Group Add *3 4
Transmission Trunked Mode *2 Message Trunked Mode *2 Failsoft Mode *2 Call Queuing with Priority *2 Telephone Interconnect *4 *1: RX / Talkback only on the NX-220E3/320E3 *2: These trunked features are primarily system programming and operational dependent. Priority Monitor also requires NX subscriber settings. *3: Requires NX subscriber unit PC Serial Interface compatible software application (e.g Kenwood AVL & Dispatch Messaging software) or hardware (e.g. console). *4: Require KTI-4 and teleco unit DIGITAL TRUNKING MULTI-SITE MODE 60,000 GIDs per Network 60,000 UIDs per Network Wide Area All Group Call Auto-Roaming / Registration Multi-Site IP Network Compatible Group Registration SCAN TYPES (FM & NXDN CONVENTIONAL) Single/Multi-Zone Scan Dual Priority Scan (Conventional) List Scan FM MODES GENERAL 25, 20 & 12.5 khz Channels FleetSync /II* DTMF Encode / Decode* Companded Audio Voice Inversion Scrambler * Some screen/key-based functions not available on the NX-220E3/320E3 FM CONVENTIONAL ZONES QT / DQT Two-Tone Decode Single/Two-Tone Encode*1*2 5-Tone Encode / Decode Voting *1: Can be used by pre-programmed key operation on the NX-220E3/320E3 *2: Require K-firmware FleetSync /II * (FM) PTT ID Digital ANI (TX) Selective Call & Group Call*1 Status Messaging*2, *3 Emergency Status Power On/Off Status Messages *2 Send/Display GPS (KMC-48GPS) *4 PTT ID & Emergency GPS Reporting *2 Status Message Block GPS Reporting *2 Short Text Messages *2 GPS Ack Request *1: Some screen/key-based functions not available on the NX-220E3/320E3 *2: Requires NX subscriber unit PC Serial Interface compatible software application (e.g Kenwood AVL & Dispatch Messaging software) or hardware (e.g.console). *3: Can be used by pre-programmed key operation on the NX-220E3/320E3 *4: Send GPS (KMC-48GPS) on the NX-220E3/320E3 4. OPTION KNB-55L KNB-56N KNB-57L Li-Ion Battery (1480mAh) Ni-MH Battery (1400mAh) Li-Ion Battery (2000mAh) 5
KBP-5 KSC-25/30 KSC-256 KMC-45 KMC-21 KMC-48GPS KBH-12 KMB-30 KRA-22/23 KRA-26/27 KHS-21 KWR-1 KPG-22A KPG-22U KCT-53U KPG-141D 6AA Alkaline Battery Case Rapid/Regular single unit charger Rapid rate 6-Unit Charger Speaker Microphone Speaker Microphone GPS Speaker Microphone Spring action belt clip Wall Mount Bracket for KSC-256 V/UHF Low Profile Helical Antenna VHF Helical/UHF Whip Antenna Headset w/boom mic & PTT Water resistant bag Programming interface Cable USB Programming Interface Cable USB Adapter (USB/DB-9) Programming Software 5. SUPPLIED ACCESSORIES Belt Clip (KBH-12) 2-PIN Connector Cap Instruction Manual (En, Sp, Ger, Fr, Du, It, Turkish, Greek) 6
6. SPECIFICATIONS General NX-220 NX-320 Frequency Range 136-174 MHz 400-470 MHz Number of Channels Display model 260 ch w/o Display model 64 ch Zones Display model 128 w/o Display model 4 Max. Channels per Zone Display model w/o Display model 250 16 Channel Spacing Analogue 25 / 20 / 12.5 khz Digital 12.5 / 6.25 khz Antenna Impedance Operating Voltage with KNB-55L(1480) Battery Life (5-5-90) with KNB-56N(1400) with KNB-57L(2000) Operating Temperature Range 50 Ω 7.5VDC±20% Approx. 8.5 hours Approx. 8.5 hours Approx. 11.5 hours -30 C to +60 C* Frequency Stability(-30 C to +60 C) ±2.0ppm ±1.0ppm Dimensions (W x H x D) Weight Radio only with KNB-55L with KNB-56N with KNB-57L Radio only with KNB-55L with KNB-56N with KNB-57L Applicable Standards ETSI R&TTE Environmental Specification and IP Rating Receiver Display Version 56.0 x 110.5 x 36.9 mm 56.0 x 110.5 x 37.5 mm 56.0 x 110.5 x 43.2 mm 56.0 x 110.5 x 39.5 mm 210 g 305 g 405 g Non Display Version 56.0 x 110.5 x 37.5 mm 56.0 x 110.5 x 38.1 mm 56.0 x 110.5 x 43.8 mm 56.0 x 110.5 x 40.1 mm 205 g 300 g 400 g 330 g 325 g EN 300 086, EN 300 113,, EN 300 219, EN301 489, EN 301 166 ETSI Safety EN 60065, EN 60950-1, EN 60215 IP54/55, MIL-STD-810 C,D,E,F,G Sensitivity (Analogue) EIA 12dB SINAD 0.28µV/ 0.28µV/ 0.32µV (25kHz / 20kHz/12.5kHz) EN 20dB SINAD -3dB µv/ -3dB µv/ -1dB µv Sensitivity (Digital) 3% BER 0.32µV/ 0.25µV (12.5kHz/6.25kHz) 1% BER -1dB µv/ -4dB µv Adjacent Channel Selectivity (Analogue) (25kHz / 20kHz/12.5kHz) 76dB / 74dB / 68dB Intermodulation (Analogue) 65dB Spurious Response Rejection (Analogue) 75dB Audio Distortion Less than 3% Audio Output 500mW / 8Ω * Operating temperature range of the KNB-55L/57L : -10ºC to +60ºC 7
Transmitter RF Power output High / Low 5 W / 1 W Modulation Limiting (Analogue) ±5.0 khz at 25 khz ±4.0 khz at 20 khz ±2.5 khz at 12.5 khz Spurious Emission -36 dbm 1 GHz, -30dBm > 1 GHz FM Noise (EIA) (Analogue, 25kHz / 20kHz /12.5kHz ) 45dB / 45dB / 40dB Modulation Distortion Less than 3% Microphone Impedance Modulation 1.8 kω 16K0F3E, 14K0F3E, 14K0F2D, 12K0F2D, 8K50F3E, 7K50F2D, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E, 4K00F1D, 4K00F7W, 4K00F2D Applicable MIL-STD MIL Standard Methods / Procedures 810C 810D 810E 810F 810G Low Pressure 500.1 / I 500.2 / I, II 500.3 / I, II 500.4 / I, II 500.5 / I, II High Temperature 501.1 / I, II 501.2 / I, II 501.3 / I, II 501.4 / I, II 501.5 / I, II Low Temperature 502.1 / I 502.2 / I, II 502.3 / I, II 502.4 / I, II 502.5 / I, II Temperature Shock 503.1 / I 503.2 / I 503.3 / I 503.4 / I, II 503.5 / I Solar Radiation 505.1 / I 505.2 / I 505.3 / I 505.4 / I 505.5 / I Rain 506.1 / I, II 506.2 / I,II 506.3 / I, II 506.4 / I, III 506.5 / I, III Humidity 507.1 / I, II 507.2 / II, III 507.3 / II, III 507.4 507.5 / II Salt Fog 509.1 / I 509.2 / I 509.3 / I 509.4 509.5 Dust 510.1 / I 510.2 / I 510.3 / I 510.4 / I, III 510.5 / I Vibration 514.2 / VIII, X 514.3 / I 514.4 / I 514.5 / I 514.6 / I Shock 516.2 / I, II, V 516.3 / I, IV 516.4 / I, IV 516.5 / I, IV 516.6 / I, IV Kenwood follows a policy of continuous advancement in development. For this reasons, specifications may be changed without notice. Analogue measurements made per EN Standards or TIA/EIA 603 and specifications shown are typical. 8