High sleeper - White - 190x90cm Assembly Instructions - Please keep for future reference 192925 Dimensions Length - 19cm Depth - 1cm Height - 1cm Weight - 3kg Important Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the ustomer Helpline: 005 055 or e-mail: order@fl exa.dk Issue 3-15/05/1
Safety and are Advice Important Please read these instructions fully before starting assembly heck you have all the components and tools listed on pages 2 and 3. Remove all fi ttings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand or put weight on the product, this could cause damage. Assemble the item as close to its fi nal position (in the same room) as possible. Assemble on a soft level surface to avoid damaging the unit or your fl oor. Parts of the assembly will be easier with 2 people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Dispose of all packaging carefully and responsibly. are and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. rom time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. IMPORTANT, READ AREULLY -RETAIN OR UTURE REERENE. ASSEMLY: urrent legislation requires that the bunk bed must be fi tted with safety-rails and a ladder or platform for the upper bunk bed. The bunk bed meets the European EN -20 standards for security and durability. MATTRESS: This bed is designed to use a mattress size 190 cm. long and 90 cm. wide. The total thickness must not exceed 1,1 cm. The mattress top must not pass the marking on the ladder / the post for the safety-rail. WARNIN: High beds and the upper bed of bunk beds are not suitable for children under six years due to the risk of injury from falls. Do not use the bed if any structural part is broken or missing. e aware that children can strangle in items such as ropes, strings, cords, harnesses and belts attached to or hung on a bunk bed/high bed. WARNIN: hildren can become trapped between the bed and the wall. To avoid risk of serious injury the distance between the top safety barrier and the wall shall not exceed 5 mm. or shall be more than 230 mm. MAINTENANE INSTRUTIONS: All assembly fastenings should always be tightened properly and that care should be taken that no fi ttings are loose. LEANIN: LAQUERED: Wooden, lacquered and painted as well as laminated surfaces should be wiped over with a cloth and a mild soap. OIL: Oiled surfaces can be cleaned with soapy water, e.g. brown soap. Wipe with a clean cloth. To maintain the natural life in the furniture which is provided by the oil treatment, we recommend an oil aftercare of the furniture 1-2 times a year. The colourless natural oil for maintenance of oil-treated furniture is available at your local furniture store. 1
omponents - Parts If you have damaged or missing components, call the ustomer Helpline: 005 055 Please check you have all the parts listed below 1 List (31..x1.2cm) 2 Slat x15 (9.x.5x1.5cm) No. -00311-20 No. -015091 3 Endrail (.x.9.0cm) No. -02001-20 Endrail x (.x.5.0cm) No. -020015-20 5 Endrail (.x.9.0cm) No. -02001-20 Tread x5 (31.x.0.cm) No. -020311-20 Safety rail 3/ (150.9x.5.0cm) No. -02015092-20 Ladder side (12.9x.9.0cm) No. -0201291-20 9 Safety rail 1/1 x1 (1.x.9.0cm) No. -02012-20 2
omponents - Parts Please check you have all the parts listed below Safety rail 1/1 (1.x.5.0cm) No. -02013-20 Leg x (1.2x.3x.3cm) No. -03121-20 edside (1.x.9.0cm) No. 1305-13-20 3
omponents - ittings Please check you have all the fi ttings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings may be supplied than are required. No. 3901-30020 No. 3922-001 A 3.00mm hipboard screw M Øx1mm arrel nut x No. 3930-05 No. 3913-0055 D E x5mm Dowel x30 Mx55mm onnecting bolt x1 No. 3909-3090 No. 393-0000-2 H.3x90mm Assembly screw ømm over cap plastic x No. 3913-00 No. 3923-0015 K No. 3901-0030.0x30mm hipboard screw x No. 3909-3050.3x50mm Assembly screw No. 393-000-2 i ømm over cap plastic No. 393-00001-2 L Mx0mm onnecting bolt x M No. 00-022 ø/mx15mm Sleeve nut x1 No. 00-023 N ømm over cap plastic x No. 390-00015 O ø/ø.3x15mm Spacer Plastic x1 0x0,50mm Angle 15.5x3mm racket Tools required Phillips screwdriver (medium) latblade screwdriver (medium) Allen key mm incl. No. 033-00 Small hammer Ruler/tape measure Eye protection (when using a hammer or glue)
Assembly Instructions Step 1 Attach the dowels D to the endrails 3 and and to the bedside and to the safety rails 9 and. D D D x 3 D 9 Step 2 Attach the leg to the endrails 3, and 5 with assembly screws using the Allen Key. Repeat same procedure for both headboard and footboard. 3 5 Step 3 Attach the leg to the endrails 3, and 5 with assembly screws using the Allen Key. Repeat same procedure for both headboard and footboard. 5 3 5
Assembly Instructions Step Attach the bedside and the safety rails 9 and to end boards fi rstly by placing the dowels in the holes in end boards. The thin rail attached to the bedsides should face inwards. Push barrel nuts into the small holes in the bedside and the safety rail 9, the groove on barrel nut should be horizontal. Push connecting bolts through each leg to meet barrel nuts and then fasten with the Allen Key. Attach the safety rails to the leg with assembly screws. 9 9 Step 5 Attach the bedside and the safety rails to end boards fi rstly by placing the dowels in holes in endboards. The thin rail attached to the bedside should face inwards. Push barrel nuts into the small holes in the bedside the groove on barrel nut should be horizontal. Push connecting bolt through each leg to meet barrel nut and then fasten with the Allen Key. Attach the safety rails to the leg with assembly screws. Ladder can be positioned left or right.
Assembly Instructions Step Attach the treads to the ladder sides with assembly screws. Attach the bracket N to the ladder side with chipboard screws. N N ront edge N ront edge Step 1,5 mm,5 mm Attach the ladder side to the leg with the sleeve nut K and connecting bolt E. Attach the ladder side to the safety rails with the spacer O and assembly screws. Attach the ladder sides to the bedside with chipboard screws A. E K O O K A A A E
Assembly Instructions Step Place 1 slat 2 in the centre of the bed. ollow the measurement and place 2 following slats 2 in the bed with a distance of 3 mm between each. Push the bedsides together whilst attaching slats 2 to the bed with chipboard screws. 3 mm PUSH 2 2 2 PUSH Step 9 Position the remaining slats 2 in the bed with a distance of 3,5 mm between each. 3,5mm asten each slat with chipboard screws.
Assembly Instructions Step M Max. mattress height! Attach the safety list 1 inside the bed, on the front safety rails Should be in the center of the front guards between the slats. 1 Attach it 1 to the safety rails and the bedside with chipboard screws. 1 ollow the measurement. Attach the safety list 1 on the outside of the bed, on the back safety rails Should be in the center of the back guards. Attach it 1 to the safety rails and the bedside with chipboard screws ollow the measurement. M Attach the wall bracket M to the leg with chipboard screws. 1 mm 1 mm Max. mattress height! Assembly is complete. 1 1 1 mm 1 mm If you need help or have damaged or missing parts, call the ustomer Helpline: 005 055 E-mail: order@flexa.dk 9 Ref.no. -0132-20 Stand: 15051 Page (0-501-20)