IPA FITTINGS FOR SCHÜCO ALU INSIDE NORDIC 2017 A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45) 98 35 15 00
3 FITTINGS FOR SCHÜCO ALU INSIDE NORDIC Table of contents PAGE SCHÜCO ALU INSIDE NORDIC profile 4 Suggestion - Number of Hinges 6 Suggestion - Hinge Positions 7 IPA NO. DESCRIPTION PAGE IPA No. 61474 Window Hinge 8 IPA No. 62444-52 Top Swing Fitting 9-10 IPA No. 62462 Safety Restrictor 9-10 IPA No. 62475 Canopy Stay 11-12 IPA No. 62486...87 + 89 Adjustable Canopy Stay 13-14 IPA No. 62488 Adjustable Canopy Stay with Adjustable Friction 15-16 IPA No. 62496...97 Side Swing Window 90 0 - Adjustable 17-18 IPA No. 62436 Safety Catch 19-20 IPA No. 62427 Friction Stay for Windows 21 IPA No. 62422 Accessories - Locking Block 22 IPA No. 62426 Accessories - Roller Block 22 IPA No. 62433 Accessories - Support Block for screws 22 IPA No. 21371 +79 Casement Hook 23-24 IPA No. 21382 Hook Catch 23-24 IPA No. 21396 Casement Fasteners 23-24 Shortening of slidring rails 25 Maintenance - Lubrication Instructions 26-27 17/05
4 SCHÜCO ALU INSIDE NORDIC PROFILE FITTING INSTRUCTIONS 31 12.4 2.2 4 23 5.5 16.3 12 15/10
5 SCHÜCO ALU INSIDE NORDIC IPA HAS IN COORPORATION WITH SCHÜCO DEVELOPED A SERIES OF FIT- TINGS FOR THE SCHÜCO ALU INSIDE NORDIC PROFILE. 15/10
6 FITTING SUGGESTION INSTRUCTIONS - NUMBER OF HINGES The chart below shows the number of hinges, we suggest to use on different sizes of windows and doors. The chart shall ONLY be considered as a guidance, as the number of hinges also will depend on the use and weight of the window/door. If the window/door is mounted in a public building with many users (Schools, Railway Stations etc.) then more or even larger hinges are recommended. Also we suggest to use a support fi tting whenever possible. WINDOW HINGES: Valid for the window hinges shown in this catalogue. All window hinges meet the requirements of class 9 (60 Kgs.) in accordance with DS/EN 1935. The numbers in brackets are the number of hinges needed in windows with 3-layer glass. Width Height < 500 501-600 601-700 701-800 1401-1500 2 (3) 3 (3) 3 (3) 3 (4) 1301-1400 2 (3) 3 (3) 3 (3) 3 (4) 1201-1300 2 (3) 3 (3) 3 (3) 3 (4) 1101-1200 2 (3) 3 (3) 3 (3) 3 (4) 1001-1100 2 (3) 3 (3) 3 (3) 3 (3) 901-1000 2 (2) 2 (2) 2 (2) 3 (3) 801-900 2 (2) 2 (2) 2 (2) 3 (3) 701-800 2 (2) 2 (2) 2 (2) 3 (3) 601-700 2 (2) 2 (2) 2 (2) 501-600 2 (2) 2 (2) < 500 2 (2) 16/09
7 SUGGESTION - HINGE POSITIONS 90 130 130 90 250 250 250 130 130 ATTENTION: The suggested placement of the hinges is ONLY a recommendation. When mounting Window - or Door elements in buildings the fastening points of the Frame should be by the hinges, supporting the Frame as best as possible in the areas where the load from the sash/door is transferred to the Frame. 18.08
8 WINDOW HINGE IPA No. 61474 C ORDERING NO. MATERIAL SURFACE A IPA NO. STEEL FIXED STEEL PIN SQUARE EDGES LEFT SQUARE EDGES RIGHT GALVANIZED FITTING INSTRUCTIONS SCHÜCO ALU INSIDE NORDIC: 31 16.3 12.4 12 2.2 INDUSTRY PACKING IN BOXES OF 100 PCS. A MM B MM C MM MATERIALE MM PIN MM SCREW APPROX. WEIGHT KGS / PC. 61474 2 3 4 87 2 90 58.5 51 2,5 8 4,0 0,18 B RIGHT SUPPORT BLOCK FOR SCREWS IS INCLUDED IPA No. 61474 4 5.5 SUPPORT BLOCK FOR SCREWS FIG. 1 FIG. 2 USE SCREW NO. 4.0. MAINTENANCE: TEST THE OPERATION FROM TIME TO TIME. WHEN FITTING - GREASE THE PIVOT/MOVABLE METAL PARTS OF THE MECHANISM WHILE ACTIVATING REPEATEDLY. HEREAFTER GREASE MINIMUM TWICE A YEAR. SEE ALSO INSTRUCTIONS ON PAGE 26-27. 16/09
9 TOP SWING FITTING IPA No. 62444-52 & IPA No. 62462 ORDERING NO. IPA NO. MATERIAL STEEL W/O SPECIFICATION SURFACE ELECTROPLATED STANDARD PACKINGS IN BOXES OF 1 SET A MM B MM FRAME DIMENSIONS INSIDE MM SCREW WEIGHT APPROX. KGS / SET 62444 1 0 21 1 38.5 545 545-644 4,0 1,08 62445 1 0 21 1 38.5 645 645-744 4,0 1,26 62446 1 0 21 1 38.5 745 745-844 4,0 1,44 62447 1 0 21 1 38,5 845 845-944 4,0 1,62 B 62448 1 0 21 1 38,5 945 945-1044 4,0 1,80 62449 1 0 21 1 38,5 1045 1045-1144 4,0 1,98 62450 1 0 21 1 38,5 1145 1145-1244 4,0 2,16 62451 1 0 21 1 38,5 1245 1245-1344 4,0 2,34 62452 1 0 21 1 38,5 1345 1345-1444 4,0 2,52 1/2 SET CONSEALED FITTING ADJUSTABLE FRICTION FULLY REVERSIBLE 170 0 OPENS CLEAR OF CURTAINS AND WINDOW FRAME ANODIZED ALUMINIUM RAILS A FIRE-ESCAPE OPENING: 600 MM ON IPA NO. 62448 - FROM OUTSIDE FRAME DIMENSION 1035 MM ORDERING NO. A SAFETY RESTRICTOR IPA NO. 62462 IPA NO. MATERIAL STEEL RIGHT SURFACE ELECTROPLATED STANDARD PACKING IN BOXES OF 25 PCS. A MM SCREW WEIGHT APPROX. KGS / PC. 62462 1 8 21 1 65 4,0 0,03 16/07
10 IPA No. 62444-52 & IPA No. 62462 FITTING INSTRUCTIONS TOP FRAME PROFILE: 31 22 = 54.5 2.5 16.3 4 5.5 SIDE FRAME = FIG. 2 37.5 2.2 PLACING OF FRAME SCREWS TOP SASH FIG. 3 SASH SIDE SASH FITTING: 1. PLACE FITTING INTO BOTH SIDES OF THE FRAME. IPA NO. 62462 FITTING ON FRAME FIG. 1 2. POSITION FITTING AGAINST TOP FRAME AND FASTEN. 3. INSERT THE SASH BETWEEN HINGE ARMS AND PUSH THE SASH AGAINST THE STOP BRACKET. FASTEN THE SASH STARTING WITH THE SCREW IN THE STOP BRACKET. 4. THE SASH CAN BE OPENED TO ANY ANGLE. WITH LARGE OPENING ANGLE A LIGHT FRIC- TION CAN BE OBTAINED BY MEANS OF THE FRICTION SCREWS IN THE SIDES. THE FRICTION HAS TO BE THE SAME ON BOTH SIDES. PLEASE NOTE THAT THE SASH IS NOT SECURED FOR HEAVY WINDS AND OTHER HEAVY INFLUENCE. USE SCREW NO. 4.0. IPA NO. FITTING LENGTH MM MAX. WEIGHT KGS 62444 545 60 62445 645 60 62446 745 60 62447 845 60 62448 945 60 62449 1045 60 62450 1145 60 62451 1245 60 62452 1345 60 USE THE LARGEST POSSIBLE FITTING OPERATION PIN 5. FIT THE RESTRICTOR IPA NO. 62462 ON THE LEFT SIDE, SEE FIG. 1. OPERATION INSTRUCTIONS: 1. OPEN THE WINDOW - THE RESTRICTOR WILL AUTOMATICALLY RESTRICT THE WINDOW. 2. PULL THE SASH 20 MM - PULL THE OPERATION PIN INWARDS AND OPEN THE WINDOW. 3. WHEN THE WINDOW IS REVERSED FOR CLEANING, THE RESTRICTOR WILL LOCK AUTOMATICALLY DISENGAGE AS MENTIONED IN POINT 2. OBS: FOR WINDOWS WITH A MULLION OR A TRANSOM THE ALUMINIUM RAIL MUST BE SHORTENED TO MAKE SPACE FOR METAL HOLDER FOR THE MULLION OR TRANSOM, SEE PAGE 25. MAINTENANCE: THE FITTINGS ARE NOT TO BE PAINTED. WHEN FITTING - LUBRICATE THE PIVOT/MOVABLE METAL PARTS OF THE MECHANISM WHILE ACTIVATING REPEATEDLY. HERAFTER LIBRICATE MINIMUM TWICE A YEAR. DO NOT GREASE THE ALUMINIUM RAILS. TEST THE OPERATION FROM TIME TO TIME. SEE ALSO INSTRUCTIONS ON PAGE 26-27. 16/09
CANOPY STAY WITH FRICTION IPA No. 62475 11 A ORDERING NO. MATERIAL SURFACE IPA NO. STEEL W/O SPECIFICATION ELECTROPLATED STANDARD PACKING IN BOXES OF 5 SETS A MM B MM SCREW APPROX. WEIGHT KG / SET B 62475 1 0 21 1 38,5 138 4,0 0,28 CONCEALED FITTINGS ADJUSTABLE FRICTION ANODIZED ALUMINIUM RAILS THE MOVEMENT OF THE FITTING ENSURES MAXIMUM SEALING 1/2 SET 15/10
12 IPA No. 62475 FITTING INSTRUCTIONS SCHÜCO ALU INSIDE NORDIC: 31 12.4 2.2 4 5.5 23 16.3 12 FIG. 1 FIG. 2 IPA NO. 62475 MAX. SASH WEIGHT KGS 20 MAX. SASH HEIGHT MM 314 MIN. SASH HEIGHT MM 179 SCREW NO. 4.0 FITTING: 1. CLOSE THE FITTING AND PLACE IT IN THE GROOVE OF THE SIDE FRAME. PLACE THE FITTING AGAINST THE TOP FRAME. PLACE AND FASTEN THE SCREWS. 2. OPEN THE FITTING AND PUSH THE SASH INTO ITS PLACE BY INSERTING IT BETWEEN THE FITTING PARTS, GUIDED BY THE GROOVES IN THE SASH, TILL THE SASH HITS THE STOPS OF THE FITTING. THIS LEAVES 5,5 MM BETWEEN SASH AND FRAME. FASTEN THE FITTING STARTING WITH THE SCREW IN THE STOP BRACKET. 3. NOW THE FRICTION MAY BE ADJUSTED BY MEANS OF THE SCREWS IN THE SLIDES. THE BEST RESULT FOR THE WINDOW MOVEMENT IS ACHIEVED BY EQUAL FRICTION AT EITHER SIDE. OBS: FOR WINDOWS WITH A MULLION OR A TRANSOM THE ALUMINIUM RAIL MUST BE SHORTENED TO MAKE SPACE FOR METAL HOLDER FOR THE MULLION OR TRANSOM, SEE PAGE 25. MAINTENANCE: THE FITTINGS ARE NOT TO BE PAINTED. TEST THE OPERATION FROM TIME TO TIME. WHEN FITTING - LUBRICATE THE PIVOT/MOVABLE METAL PARTS OF THE MECHANISM WHILE ACTIVATING REPEATEDLY. HEREAFTER LUBRICATE MINIMUM TWICE A YEAR. DO NOT LUBRICATE THE ALUMINIUM RAILS. SEE ALSO INSTRUCTIONS ON PAGE 26-27. FIG. 3 16/09
ADJUSTABLE CANOPY STAY WITH FRICTION IPA No. 62486, 62487 & 62489 13 A ORDERING NO. MATERIAL SURFACE IPA NO. STEEL W/O SPECIFICATION ELECTROPLATED STANDARD PACKING IN BOXES OF 5 SETS INDUSTRY PACKING IN BOXES OF 25 SETS A MM B MM SCREW APPROX. WEIGHT KG / SET 62486 1 0 21-2 38,5 299 4,0 0,60 B 62487 1 0 21-2 38,5 489 4,0 0,84 62489 1 0 21 1-38,5 747 4,0 1,22 1/2 SET VERTICALLY ADJUSTABLE ± 1.5 MM CONCEALED FITTINGS ADJUSTABLE FRICTION ANODIZED ALUMINIUM RAILS THE MOVEMENT OF THE FITTING ENSURES MAXIMUM SEALING FIRE-ESCAPE OPENING: PLEASE SEE WWW.IPAFITTINGS.COM/RESCUE 15/10
14 IPA No. 62486-87 & 62489 FITTING INSTRUCTIONS SCHÜCO ALU INSIDE NORDIC: 31 12.4 12 2.2 4 5.5 23 16.3 FIG. 1 FIG. 2 VERTICAL PLAN IPA NO 62486 62487 62489 MAX. SASH WEIGHT KGS 40 50 70 MAX. FRAME HEIGHT MM 854 1354 1554 SCREW NO. 4.0 4.0 4.0 FITTING: 1. CLOSE THE FITTING AND PLACE IT IN THE GROOVE OF THE SIDE FRAME. PLACE THE FITTING AGAINST THE TOP FRAME. PLACE AND FASTEN THE SCREWS. OBS! RE. IPA NO. 65487 FOR BIG WINDOWS (>1200 MM) WITH 3-LAYER GLASS AND NO REQUIREMENTS FOR EGRESS OPENINGS THE USE OF IPA NO. 65489 IS RECOMMENDED, AS THE VENTILATION POSITION OTHERWISE MAY BE DIFFICULT TO ACHIEVE BECAUSE OF THE OPENING GEOMETRY OF THE GEARS. 2 OPEN THE FITTING AND PUSH THE SASH INTO ITS PLACE BY INSERTING IT BETWEEN THE FITTING PARTS, GUIDED BY THE GROOVES IN THE SASH, TILL THE SASH HITS THE STOPS OF THE FITTING. THIS LEAVES 5,5 MM BETWEEN SASH AND FRAME. FASTEN THE FITTING STARTING WITH THE SCREW IN THE STOP BRACKET. FINALLY FASTEN THE STOP PLATE IN THE ALURAIL. 62487: FOR MAXIMUM FIRE-ESCAPE OPENING, MOUNT THE STOP PLATE THROUGH THE UPPER SCREW HOLE IN THE STOP PLATE. IF THE BOTTOM SCREW HOLE IS USED, THEN THE FIRE-ESCAPE OPENING IS REDUCED, BUT THE FITTING WILL CARRY UP TO 60 KGS. 62489: FOR MAXIMUM FIRE-ESCAPE OPENING, MOUNT THE STOP PLATE THROUGH THE UPPER SCREW HOLE IN THE STOP PLATE. IF THE MIDDLE OR LOWER SCREW HOLES IN THE STOP PLATE ARE USED THE FIRE-ESCAPE OPENING WILL BE REDUCED, BUT THE WEIGHT LIMIT IS RAISED. MIDDLE SCREW HOLE: MAX. 85 KGS. - LOWER SCREW HOLE: MAX. 100 KGS. 3. NOW THE FRICTION MAY BE ADJUSTED BY MEANS OF THE SCREWS IN THE SLIDES. THE BEST RESULT FOR THE WINDOW MOVEMENT IS ACHIEVED BY EQUAL FRICTION AT EITHER SIDE. 4. THE SASH CAN BE ADJUSTED ±1.5 MM UP OR DOWN. BEFORE ANY ADJUSTMENT THE MOUNTING SCREWS IN THE BOTTOM IN EACH SIDE OF THE FRAME HAVE TO BE LOOSENED. THEN ADJUST BY USING A TORX-20 KEY TO TURN THE ECCENTRIC PIN. ON DELIVERY THE MARK ON THE ECCENTRIC PIN IS IN A HORIZONTAL POSITION INDICATING THE 0-POSITION. WHEN THE MARK IS IN VERTICAL POSITION IN EITHER LEFT OR RIGHT SIDE, THE FITTING IS ADJUSTED TO IT S MAX OF ±1.5 MM. AFTER THE ADJUSTMENT THE MOUNTING SCREWS IN THE BOTTOM OF EACH SIDE ARE FASTENED. OBS: FOR WINDOWS WITH A MULLION OR A TRANSOM THE ALUMINIUM RAIL MUST BE SHORTENED TO MAKE SPACE FOR METAL HOLDER FOR THE MULLION OR TRANSOM, SEE PAGE 25. ECCENTRIC PIN MARK FIG. 3 MAINTENANCE: THE FITTINGS ARE NOT TO BE PAINTED. TEST THE OPERATION FROM TIME TO TIME. WHEN FITTING - LUBRICATE THE PIVOT/ MOVABLE METAL PARTS OF THE MECHANISM WHILE ACTIVATING REPEATEDLY. HEREAFTER LUBRICATE MINIMUM TWICE A YEAR. DO NOT LUBRICATE THE ALUMINIUM RAILS. SEE ALSO INSTRUCTIONS ON PAGE 26-27. 16/11
ADJUSTABLE CANOPY STAY WITH ADJUSTABLE FRICTION IPA No. 62488 15 A ORDERING NO. MATERIAL SURFACE IPA NO. STEEL W/O SPECIFICATION ELECTROPLATED STANDARD PACKING IN BOXES OF 5 SETS A MM B MM SCREW APPROX. WEIGHT KG / SET 62488 1 0 21 1 38,5 505 4,0 0,86 B VERTICALLY ADJUSTABLE ± 1.5 MM CONCEALED FITTINGS ADJUSTABLE DOUBLE FRICTION ANODIZED ALUMINIUM RAILS THE MOVEMENT OF THE FITTING ENSURES MAXIMUM SEALING THE MOVEMENT OF THE FITTING ENSURES BETTER FIRE-ESCAPE OPENING 1/2 SET FIRE-ESCAPE OPENING: PLEASE SEE WWW.IPAFITTINGS.COM/RESCUE 15/10
16 IPA No. 62488 FITTING INSTRUCTIONS SCHÜCO ALU INSIDE NORDIC: 31 12.4 12 2.2 4 5.5 23 16.3 FIG. 1 FIG. 2 VERTICAL PLAN IPA NO. 62488 MAX. SASH WEIGHT KGS 50 MAX. FRAME HEIGHT MM 1154 SCREW 4.0 FITTING: 1. CLOSE THE FITTING AND PLACE IT IN THE GROOVE OF THE SIDE FRAME. PLACE THE FITTING AGAINST THE TOP FRAME. PLACE AND FASTEN THE SCREWS. 2 OPEN THE FITTING AND PUSH THE SASH INTO ITS PLACE BY INSERTING IT BETWEEN THE FITTINGS, GUIDED BY THE GROOVES IN THE SASH, TILL THE SASH HITS THE STOPS OF THE FITTING. THIS LEAVES 5,5 MM BETWEEN SASH AND FRAME. FASTEN THE FITTING STARTING WITH THE SCREW IN THE STOP BRACKET. 3. NOW THE FRICTION MAY BE ADJUSTED BY MEANS OF THE SCREWS IN THE SLIDES. WHEN ADJUSTING MAKE SURE, THAT THE TOP GLIDER MOVES FIRST DOWN TO THE STOP. THE BEST RESULT FOR THE WINDOW MOVEMENT IS ACHIEVED BY EQUAL FRICTION AT EITHER SIDE. 4. THE SASH CAN BE ADJUSTED ±1.5 MM UP OR DOWN. BEFORE ANY ADJUST- MENT THE MOUNTING SCREWS IN THE BOTTOM IN EACH SIDE OF THE FRAME HAVE TO BE LOOSENED. THEN ADJUST BY USING A TORX-20 KEY TO TURN THE ECCENTRIC PIN. ON DELIVERY THE MARK ON THE ECCENTRIC PIN IS IN A HORIZONTAL POSITION INDICATING THE 0-POSITION. WHEN THE MARK IS IN VERTICAL POSTION IN EITHER LEFT OR RIGHT SIDE, THE FITTING IS ADJUSTED TO IT S MAX OF ±1.5 MM. AFTER THE ADJUSTMENT THE MOUNTING SCREWS IN THE BOTTOM OF EACH SIDE ARE FASTENED. ECCENTRIC PIN MARK OBS: FOR WINDOWS WITH A MULLION OR A TRANSOM THE ALUMINIUM RAIL MUST BE SHORTENED TO MAKE SPACE FOR METAL HOLDER FOR THE MULLION OR TRANSOM, SEE PAGE 25. MAINTENANCE: THE FITTINGS ARE NOT TO BE PAINTED. TEST THE OPERATION FROM TIME TO TIME. WHEN FITTING - LUBRICATE THE PIVOT/MOVABLE METAL PARTS OF THE MECHANISM WHILE ACTIVATING REPEATEDLY. HEREAFTER LUBRICATE MINIMUM TWICE A YEAR. DO NOT LUBRICATE THE ALUMINIUM RAILS. SEE ALSO INSTRUCTIONS ON PAGE 26-27. FIG. 3 16/09
SIDE SWING WINDOW 90 0 WITH FRICTION IPA No. 62496-97 - Adjustable 17 ORDERING NO. A MATERIAL SURFACE IPA NO. STEEL LEFT RIGHT ELECTROPLATED STANDARD PACKING IN BOXES OF 5 SETS A MM B MM SCREW APPROX. WEIGHT KG / SET 62496 1 7 8 21 1 38,5 229,5 4,0 0,40 B 62497 1 7 8 21 1 38,5 350,5 4,0 0,63 HORISONTALLY ADJUSTABLE ± 1.5 MM CONVENIENT FOR CLEANING OPENS UP TO 90 MAXIMUM VENTILATION CONCEALED FITTINGS ANODIZED ALUMINIUM RAILS OPENS CLEAR FROM CURTAINS AND WINDOW FRAME FIRE-ESCAPE OPENING: PLEASE SEE WWW.IPAFITTINGS.COM/RESCUE 15/10
18 SCHÜCO ALU INSIDE NORDIC: IPA No. 62496-97 FITTING INSTRUCTIONS 31 4 5.5 23 MARK 12 2.2 ECCENTRIC PIN FIG. 2 HORIZONTAL PLAN HINGE SIDE FITTING SHOWN IN FRAME CILL RIGHT HAND ILLUSTRATION FIG. 1 VERTICAL PLAN IPA NO. 62496 62497 MAX. WEIGHT OF SASH KGS 20 40 MIN. WIDTH OF SASH MM 215 342 MAX. WIDTH OF SASH MM 336 842 USE SCREW NO. 4.0 4.0 FITTING: 1. THE FITTING SHOULD BE POSITIONED IN THE GROOVES IN TOP AND BOTTOM OF FRAME AGAINST THE SIDE FRAME AND FASTENED (FIGURE 1 AND 2). 2. OPEN THE FITTING AND PUSH THE WINDOW SASH INTO POSITION BETWEEN THE 2 FITTING PARTS AGAINST THE ANGLE AND FASTEN THE SCREWS. START WITH THE SCREW IN THE ANGLE. 3. THE OPENING BETWEEN SASH AND FRAME CAN BE ADJUSTED BY MEANS OF THE ECCENTRIC PIN - USE A TORX-20 KEY. ON DELIVERY THE ADJUSTMENT IS IN NEUTRAL POSITION, SEE THE MARK ON THE PIN. THE PIN CAN BE TURNED 90 TO EATHER SIDE, WHICH GIVES AN ADJUSTMENT OF ±0.5 MM. OBS: FOR WINDOWS WITH A MULLION OR A TRANSOM THE ALUMINIUM RAIL MUST BE SHORTENED TO MAKE SPACE FOR METAL HOLDER FOR THE MULLION OR TRANSOM, SEE PAGE 25. MAINTENANCE: THE FITTINGS ARE NOT TO BE PAINTED. TEST THE OPERATION FROM TIME TO TIME. WHEN FITTING - LUBRICATE THE PIVOT/MOVABLE METAL PARTS OF THE MECHANISM WHILE ACTIVATING REPEATEDLY. HEREAFTER LUBRICATE MINIMUM TWICE A YEAR. DO NOT LUBRICATE THE ALUMINIUM RAILS. SEE ALSO INSTRUCTIONS ON PAGE 26-27. 16/09 FIG. 3 REG. TALL AND NARROW WINDOWS: PLEASE NOTICE THAT ON TALL AND NARROW SASHES THE FLEXIBILITY OF THE MATERIAL MAY EFFECT THE MOVEMENT OF THE FITTING S SLIDING ELEMENTS IN TOP AND BOTTOM. THEREFORE IT CAN BE NECESSARY TO USE BOTH HANDS TO STABILIZE THE SASH WHEN OPENING THE WINDOW. THESE FITTINGS ARE NOT SUITABLE FOR DOOR HEIGHT WINDOWS.
19 SAFETY CATCH IPA No. 62436 A ORDERING NO. IPA NO. MATERIAL STEEL LEFT RIGHT SURFACE ELECTROPLATED INDUSTRY PACKING IN BOXES OF 25 SETS A MM SCREW APPROX. WEIGHT KG / SET 62436 1 7 8 21 2 92 4,0 0,08 1 SET RIGHT 15/10
20 IPA No. 62436 FITTING INSTRUCTIONS SCHÜCO ALU INSIDE NORDIC: 5.5 2.2 4 12 X + 95 MARK 31 16.3 12.4 SASH X BOTTOM FRAME SIDE FRAME FIG. 1 RIGHT HAND ILLUSTRATION (SEEN FROM THE OUTSIDE) FIG. 2 THE FITTING CAN BE USED ON BOTH SIDEHUNG/SIDE SWING AS WELL AS TOPHUNG/CANOPY STAY WINDOWS. ON TOPHUNG/CANOPY STAY WINDOWS THE RESTRICTOR IS PLACED IN THE BOTTOM OF THE SIDE FRAME AND THE RECEIVER IS PLACED IN THE BOTTOM OF THE SIDE SASH. ON THE SIDEHUNG/SIDE SWING WINDOWS THE RESTRICTOR IS PLACED IN BOTTOM FRAME ON THE OPPOSITE SIDE OF THE HINGES/FITTINGS AND THE RECEIVER IS PLACED ACCORDINGLY IN THE BOTTOM SASH. X-DIMENSION IS OPTIONAL. BY USING LARGER X-DIMENSION THE OPENING WILL BE EXTENDED. IMPORTANT: THE RECEIVER MUST BE MOUNTED SO THAT THE PIN HITS THE MARK ON THE RESTRICTOR ARM WHEN CLOSING THE WINDOW. SEE FIG. 1 OPERATING INSTRUCTIONS: 1. OPEN THE WINDOW UNTIL THE RESTRICTOR ENGAGES. 2 PULL THE SASH APPROXIMATELY 20 MM BACKWARDS. 3. PRESS THE RESTRICTOR IN THE DIRECTION OF THE ARROW AS YOU OPEN THE WINDOW. 4. WHEN THE WINDOW IS CLOSED THE RESTRICTOR RE-ENGAGES AUTOMATICALLY. USE SCREW NO. 4.0 MAINTENANCE: THE FITTINGS ARE NOT TO BE PAINTED. TEST THE OPERATION FROM TIME TO TIME. WHEN FITTING - LUBRICATE THE PIVOT/MOVABLE METAL PARTS OF THE MECHANISM WHILE ACTIVATING REPEATEDLY. HEREAFTER LUBRICATE MINIMUM TWICE A YEAR. DO NOT LUBRICATE THE ALUMINIUM RAILS. SEE ALSO INSTRUCTIONS ON PAGE 26-27. 16/09
21 FRICTION STAY for windows IPA No. 62427 ORDERING NO. A B IPA NO. MATERIAL STEEL LEFT RIGHT SURFACE ELECTROPLATED STANDARD PACKING IN BOXES OF 25 PIECES A MM B MM MATERIAL MM SCREW APPROX. WEIGHT KG / PC. 62427 1 7 8 21 1 38,5 260 17 X 3 4,0 0,08 RIGHT CONCEALED FITTING OPENS UP TILL 100 FRICTION IN ALL POSITIONS ADJUSTABLE FRICTION ANODIZED ALUMINIUM RAIL IPA No. 61474 FITTING INSTRUCTIONS 100 260 SCHÜCO ALU INSIDE NORDIC: 31 16.3 12.4 2.2 4 5.5 ADJUSTABLE FRICTION 12 USE SCREW NO. 4.0 FIG. 2 117 30 FIG. 1 16/09 MAINTENANCE: THE FITTING IS NOT TO BE PAINTED. TEST THE OPERATION FROM TIME TO TIME. WHEN MOUNTING - LUBRICATE THE PIVOT/MOVABLE METAL PARTS OF THE MECHANISM WHILE ACTIVATING REPEATEDLY. HERAFTER LUBRICATE MINIMUM TWICE A YEAR. DO NOT LUBRICATE THE ALUMINIUM RAIL. SEE ALSO INSTRUCTIONS ON PAGE 26-27. FIG. 3
22 ACCESSORIES FITTING IPA No. 62422, INSTRUCTIONS 62426 & 62433 C A B F D E 62422 LOCKING BLOCK C A B F D E 62426 ROLLER BLOCK ORDERING NO. C B 62433 SUPPORT BLOCK FOR SCREWS A IPA NO. MATERIAL PLASTIC W/O SPECIFICATION SURFACE GREY WHITE STANDARD PACKING IN BOXES OF 100 PIECES INDUSTRY PACKING IN BOXES OF 100 PIECES A MM B MM C MM D MM E MM F MM SCREW APPROX. WEIGHT KG / 100 PIECES. 62422 0 0 00-1 - 50 30,5 14 29,5 26,5 24 4,0 1,6 62426 0 0 00-1 - 25 25,5 6,5 50 13,5 10 4,0 0,6 62433 9 0-56 - 2 42 12,5 9,5 - - - - 0,4 15/10
23 CASEMENT HOOKS & CASEMENT FASTENERS ORDERING NO. MATERIAL SURFACE A B A B IPA NO. ZINK ALLOY W/O SPECIFICATION ELECTROPLATED / WHITE ELECTROPLATED ELECTROPLATED YELLOW STANDARD PACKING IN BOXES OF 50 PIECES INDUSTRY PACKING IN BOXES OF 250 PIECES A MM B MM HOLE FOR PIN MM APPROX. WEIGHT KG / 100 PIECES 21371 21379 21371 0 0 06 21 25-2 130 95 6 6,0 0 0-21 25 1-21379 120 93 6 5,6 0 0 06 21 25-2 ATTENTION: IPA NO. 21379 IN POWDER PAINTED VERSIONS CAN ONLY BE USED TOGETHER WITH IPA NO. 21382. A B MATERIAL ORDERING NO. SURFACE 21382 A IPA NO. STEEL W/O SPECIFICATION ELECTROPLATED / WHITE ELECTROPLATED ELECTROPLATED YELLOW STANDARD PACKING IN BOXES OF 50 PIECES INDUSTRY PACKING IN BOXES OF 250 PIECES INDUSTRY PACKING IN BOXES OF 500 PIECES A MM B MM PIN MM SCREW APPROX. WEIGHT KG / 100 PIECES B 1 0-21 25 1 - - 21382 13,3 34 5,6 3,5 0,75 1 0 06-25 - 2-21396 1 0 06 21 25 - - 2 24 50-3,5 5,0 21396 18.08
24 FITTING INSTRUCTIONS IPA NO. 21371 + 21379 + 21382 DRILL 5 MM HOLE FOR RING SCREW SASH FRAME 28 5 9 FIG. 1 IPA NO. 21382 FIG. 2 IPA NO. 21371 WITH 21382 IPA NO. 21396 12.5 SASH FRAME FRAME 23 11.2 28 22 7 22 10 9 FIG. 3 IPA NO. 21379 WITH 21382 SASH SASH FRAME FITTING: 1. MOUNT THE RECEIVER 1 IN THE WANTED HEIGHT ON THE SIDE FRAME. 2. FOR CASEMENT FASTENERS WITH SCREW PLATE 2 MEASURE PRECISELY ON THE SASH AND PRE- DRILL FOR THE RING SCREW. MARK UP THE 2 SCREW HOLES ON THE SCREW PLATE AND FASTEN THE CASEMENT FASTENER. 17/05
11 25 SHORTENING OF SLIDING RAILS FOR WINDOWS WITH MULLIONS OR TRANSOMS When using a canopy stay gear, a sideswing gear or a fully reversible top swing gear in windows with mullions or transoms, it is necessary to shorten the alurail of the gear to make space for the metal holder for the mullion or transom. Open the gear and shorten the alurail, see pictures below. After cutting the alurail, place it against the metal holder and fasten the screws. 11 16/09
26 MAINTENANCE FITTING LUBRICATION INSTRUCTIONS GENERALLY all parts of a building have to be looked after and maintained from time to time. This of course also applies for fi ttings in windows and doors. How often fi ttings in windows and doors should be maintained depends to a large extent on how they are used, how often they are operated, and not least on the environment the fi ttings are exposed to. Corrosion may also be caused by other factors, such as corrosive liquids, air pollution etc. Special attention should be given to fi ttings used in windows and doors in urban and industrial areas or other areas with a high traffi c intensity as well as coastal areas. Fittings in such environments should be checked and greased more often than fi ttings used in areas with less corrosive effects. HINGES AND FITTINGS should be lubricated when necessary, or at the minimum twice a year. SLIDING ELEMENTS AS WELL AS ALL ALURAILS with sliding surfaces are to be kept clean and free from dust and dirt to ensure a smooth sliding function. Stearin wax or a clean lubricating fi lm (but no oil and no grease!) can be applied onto the alluminium rails. STAINLESS STEEL can get some discoloration, although this rarely happens. Different chemical infl uences like acid fumes, contamination from wood preservation treatments, or air pollution may cause discoloration of the metal, sometimes to a reddish tone which could look like rust. Thin discoloration can be removed just by using common cleaner or polish. Continues... 16/09
27 MAINTENANCE LUBRICATION INSTRUCTIONS PAINTED FITTINGS will from time to time need repainting. Before painting all parts should be cleaned carefully. When choosing type of paint and when applying the paint remember to follow the instructions from the paint manufacturer very carefully. When painting a wooden window in a house, it is a good idea also to paint the visible parts of the fi ttings (please note: No alurails nor sliding parts should ever be painted!). The painting of the fi tting will minimize corrosion and add to the lifetime of the fi tting. Always make sure that the proper function of a fi tting is not affected by the painting. ANODIZED ALUMINIUM should be cleaned from time to time, depending on the surroundings in which it is placed. Cleaning of the surface with a cloth or sponge is recommended. Eventually a neutral solvent can be used. Emery cloth, steel wool, sodium carbonate, and other cleansers or abrasives containing alkalies or acid should never be used. ON THE WINDOW AND DOOR FACTORY SITE all fittings should be lubricated or greased before shipment. Hinges should be lubricated with acidfree oil while activating repeatedly, an acidfree grease can also be used. When using grease it should be applied directly onto the pin of the hinges. It may be necessary to dismantle the sash before greasing. Especially hinges with a brass pin should be greased. When mounting fi ttings, please make sure that the tools do not damage the original surface treatment. When original surface has been damaged make sure that remedial measures take place as soon as possible. WHEN IN DOUBT PLEASE CONTACT YOUR LOCAL SUPPLIER OR A/S J. PETERSENS BESLAGFABRIK. 16/09
28 FITTING NOTES INSTRUCTIONS
NOTES 29
30 NOTES FITTING INSTRUCTIONS
A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL.: (+45) 98 35 15 00 www.ipafittings.com ipa@ipafi ttings.com