F10I-EGSM Single System 1
Table of contents How it works... 3 Package contents... 4 Troubleshooting... 14 Specifications... 15 Product Warranty... 16 Safety Warnings... 17 2
How it works Huaptec F10I-EGSM is designed to help mobile users to amplify weak 2G signals. Huaptec amplifiers are bi-directional. The donor antenna receives the signals from a cell tower, amplifies them and transmits to the signal booster. Then the indoor antenna receives the signals and retransmits them to your mobile device. The signals produced by your phone are amplified by the indoor antenna via the booster and donor antenna. 3
Package contents Single System Signal booster Outdoor panel antenna Indoor antenna whip Power supply 9V/3A RF cable Waterproof tape We will provide all accessories needed for the signal booster.for more information please visit www.huaptec.eu Optional antenna kits Omni ceiling antenna YAGI antenna Indoor panel antenna 4
Install your hardware Before you install 1 Make sure you have sufficient cable length between donor/server antenna location and booster connector. 2 Make sure the place where you install the booster is well ventilated, near to electrical outlet, and away from excessive heat, moisture and direct sunlight. Installation overview 1 Install your donor antenna on the roof where signal reception is the strongest. 2 Mount your signal booster, attach the cables from the outside antenna and inside antenna to the signal booster at the designated ports, and connect the booster to the AC supply (make sure all the cables are well connected). 3 Install the indoor antenna in the area where you want to improve the signal. 5
Find the area with the strongest signal The booster s main function is to improve weak RF signals of an area. The signal strength from the outdoor antenna directly affects the efficiency of the indoor coverage. Install the Outdoor Antenna Select a proper place to install the donor antenna. Normally a roof of the building is a good choice. As shown from the above graph, you need to test the signal from A to E and select a point with best signal for installation. Choose the direction for the donor antenna. The donor antenna should point to the base mobile tower to get stronger signals. Installation of donor antenna In most cases, logarithmic periodic antenna is the best choice. You can also choose outdoor panel antenna or YAGI antenna as other options. There are 2 types of installation: wall mount or pole mount. Wall mount installation is recommended for your convenience. Step1: Unscrew antenna from L-mounting bracket on antenna 6
base with a wrench. Step2: Mount vertical plate of the L-bracket on the wall with supplied screws. Step3: Screw antenna back onto horizontal plate to the wall with supplied screws. Notes: Wrap waterproof tape around the connectors between a donor antenna and feeder lines to avoid water or other kinds of damage Install the Indoor Antenna In most cases, Indoor panel antenna is the best choice. You can also choose Omni ceiling antenna or whip antenna as other options. Step1: Select a place on the wall of the area where you want better reception. Normally, to provide an overall coverage, you will need to choose a corner. 7
Step2: Drill the screw to the wall and mount bracket on the wall. Step3: Put the panel antenna on the bracket. When you choose indoor Omni ceiling antenna or whip antenna, the best place to install it is the center of your house as the graph shows. It is better to use a directional panel antenna or Yagi when the the area is long and narrow (corridors, long row of houses in two 8
sides, tunnels or elevators or rural open space) Install the signal booster Step1: Select a location close to a power outlet on a wall. Step2: Mount the booster with screws included into the kit as shown in the picture. Step3: Connect the outdoor antenna cables to the booster connector marked as outdoor. Tighten the connection by hand or with a wrench. Step4: Connect the indoor antenna cables to booster connector marked indoor. Tighten the connection by hand or with a wrench. Step5: Connect the AC power cord to the signal booster, then plug in into the electrical outlet. Step6: Power on the booster. 9
Booster installation Connection from cable to Booster Booster Commissioning After the booster is on, it will automatically adjust best performance with the intelligent automatic gain control function. No manual operation is needed. if the alarm LED flashes green or orange, that means the booster is working properly. Check the coverage, if it is good, the commissioning is finished. If not, you can adjust outdoor antenna position to get better outdoor signal strength or move the indoor antenna to better cover the weak signal area. If the alarm LED is flashing red, that means self- oscillation is occurring. To enhance the isolation you can enlarge the distance between indoor and outdoor antennas or add a barrier between the antennas. Adjust until the alarm LED turns green or orange. 10
If the alarm is still flashing red, the MGC function can provide further assistance as shown below. Booster s port description The following image shows the key components of booster. There are 3 kinds of components. The first one is connectors to the outdoor and indoor antennas. The second is LEDs for each band. LEDs indicate power and signal alarm. The third is DIP switch for MGC function. The following table and graph show the details. Gain attenuation DIP switch Connector to outside antenna LEDs indicate Connect to power Connector to indoor antenna 11
DIP switches The DIP switches are used to manually adjust their band gain attenuations respectively. Switches1-2 control EGSM/UMTS band s DL attenuation, 3-4 control EGSM/UMTS band s UL attenuation. The booster will work on its MAX. gain mode, but in some cases, we don t need such a big value. MGC function will help to provide a loss. For example in the image above, 1 represent 5dB and 2 represent 10dB, if you press both 1 and 2 button, you can get a loss of 5dB plus 10dB which is15 db loss. 12
LEDs Status and definition of ALARM indicators (only works for downlink signals): Status Green Orange Red Flashing Red Off ALARM It is working in linearity Warning: Input signals may be not enough, so please check on coverage effect, do not do anything if it is good; otherwise please check the donor antenna position. It is working in linearity (A little stronger input signals or slight self oscillation have occurred.) Solution: Please adjust antennas or slowly add the attenuation by MGC till you find the edge point (I.E. the Alarm LED shall stay at green color slightly turning to orange). Stop immediately when the LED color changes, it s enough to provide best coverage. There are strong input signals or severe self-oscillation, measures must be taken. Please, note that our repeaters have auto shut off function, so the red color status can only maintain for 5 seconds. There are strong input signals or severe self oscillation to lead that booster breaks down. Please check the troubleshooting or FAQ to get a solution. Repeater breaks down, or severe self-oscillation leads to auto mute. Please, re-plug the system and check if alarm LED turns red. If it does, please, take measures to keep alarm LED green; if it turns off, it means the power breaks down. 13
Troubleshooting Problem The signal booster is no power. The booster s power is on but the phone is not connected into the network and you still cannot communicate. Resolution Check the booster switch is turned on. Check the AC outlet is working. Try to fasten the connections between the different parts of the system. Change the direction of donor antenna or its installation position Use barriers (like buildings) to block signals of other operators. Good downlink signal with poor communication quality Check whether there s interference Consult the operator whether the signal source base station works well Adjust uplink gain to balance uplink and downlink The power is on but it has a signal fluctuation or a flash signal. Firstly check whether the alarm LED is orange. The orange light shows the insufficient isolation. Secondly adjust the antennas directions or locations or enlarge the distance between them. Thirdly reduce the booster s gain by ATT DIP if the above methods don t work. 14
Specifications RF Parameter Uplink Downlink Frequency Range EGSM900&UMTS 880~915MHz 925~960 MHz Max.Gain 55dB 60dB Max.Output Power 10dBm 10dBm MGC ( Step Attenuation ) AGC 15dB / 5dB step, dip switch control Adjust automatic V.S.W.R Typical 2 Electrical Parameter Impedance Power Supply LED Alarm Power LED ALC LED Mechanical Parameter I /O Port Dimensions Weight 50 ohm Input AC90~264V,output DC9V/3A Power Indicator Orange @ ALC 1~5 db, Red @ ALC 20 db ~25 db Mechanical Parameter N-Female 7*3.9*1.6inch/176*100*40mm 1.9Lbs/0.85KG Environment Parameter Operating Temperature -25ºC~+55ºC Relative humidity 5% - 95% Barometric pressure 55 kpa -106 kpa Environment Conditions IP40 15
Product Warranty 30-Day Money-Back Guarantee All Huaptec products are protected by a 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, the product may be returned to the reseller with a dated proof of purchase. 2-Year Warranty Huaptec Signal Boosters and kits are warranted for 2 years. Customers can choose to return the Signal Boosters and kits directly to the manufacturer at the purchase expense with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Huaptec. Huaptec would provide 2 options, repair or replace of the product. This warranty does not apply to any Signal Boosters or kits determined by Huaptec as subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty. All Huaptec products that are packaged with other Huaptec accessory products are intended for resale and use as a single unit. Such product kits are required to be sold to the end users or subsequent reseller as they were initially packaged. 16
Safety Warnings Users must follow the below principles: Booster should follow system requirement of communication equipment, assure good grounding and lightning protection. The power supply voltage of booster should meet the standards of security requirement; any operation shall be carried out only after cutting off power in advance. Only the professional is authorized for the operation. Do not dismantle machine, maintain or displace accessories by yourself, because in this way, the equipment may be damaged and you may even get an electric shock. Do not open the booster, touch the module of booster, or open the cover of module to touch the electronic component. The components will be damaged due to electrostatic. Please keep away from heating-equipment, because the booster will dissipate heat during working. And do not cover booster with anything that influences heat-dissipation. 17
18