1000 surface mouted closers Product selectio guide Surface mouted 1000 LCN closers feature a moder slim lie desig for easy istallatio o arrow head frames ad top rails. This guide is based o the desired moutig of the closer. NOTE: For parallel mouts order P versio to also receive PA Shoe. EXTERIOR DOOR PUSH SIDE MOUNTED PULL SIDE MOUNTED double Lever Arm 1250 1260 1450 1460 double Lever Arm 1250 1260 1450 1460 INTERIOR DOOR PUSH SIDE MOUNTED PULL SIDE MOUNTED double Lever Arm SINGLE Lever Arm double Lever Arm SINGLE Lever Arm 1250 1260 1450 1460 1460T 1250 1260 1450 1460 1460T Product compariso This chart shows a basic compariso of LCN 1000 closers. Refer to the specific closer chapter for complete details. MOUNTING HINGE (PULL) SIDE TOP JAMB (PULL) TOP JAMB (PUSH) PARALLEL ARM STOP FACE FINISH PAINT POWDER COAT PLATED COVER PLASTIC METAL DESIGNER SERIES CYLINDER NON-HANDED NON-SIZED ACCESSIBILITY DELAYED ACTION REGULAR (DOUBLE) STANDARD (SINGLE) HEAVY DUTY HOLD-OPEN *ARM FUNCTION 1250 180 180 180 110 110 1260 180 180 120 110 110 1450 180 180 180 110 110 1460 D 180 180 180 110 100 100 1460T D 180 115 EDA/HEDA CUSH/HCUSH SCUSH/SHCUSH AVAILABLE NOT AVAILABLE Closer available with less tha 5.0 lbs. opeig force o 36 door. * Maximum opeig/hold-ope poit with stadard template. See idividual closer series for degrees of opeig per istallatio. D = For desiger series oly. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 1
1000 surface mouted closers APPLICATIONS For alumium, hollow metal, or wood swigig doors ad frames. Ca be used with hige or pivot mouted door. Mouts o 1-3/4 trasom without adapter plates. Adapter plates ad other istallatio accessories available for uusual coditios. FEATURES COMMON TO 1000 SERIES 1000 series closers mout three ways. Closers with regular or holdope arm mout hige side or top jamb. Parallel arm, closers iclude - 62PA SHOE required for parallel arm mout. 1460T mouts hige side, top jamb (pull side) ad stop face. No-haded for right ad left swigig doors. Closers to meet ADA reduced opeig force requiremets. Adjustable hydraulic backcheck cushios opeig swig prior to 90. Separate regulatio of geeral closig speed ad latchig speed. Joits i arm ad shoe adapt to ueve trim. Reversible shoe to boost latchig power o double lever arms. DESIGN ASSISTANCE LCN has bee providig reliable solutios to uique door cotrol problems sice 1925. Desig ad specificatio assistace are oly a phoe call away. Cotact LCN for assistace or techical iformatio at 877-671-7011 or FAX 800-248-1460 (Order Etry), Fax 815-879-1495 for Product Support. WARRANTY 30 year limited warraty (1460 ) ad 20 year limited warraty (1260 ) o cast iro closers. 15 year limited warraty (1250 series) ad 25 year limited warraty (1450 series) o cast alumium closers. See Geeral Iformatio Sectio for complete warraty details. LCN s powder coat fiish surpasses 100 hours of salt spray which is over four times the ANSI stadard for corrosio resistace. Paited fiishes o cast alumium closers (1250, 1450). For istallatios where a higher level of corrosio resistace is required, LCN offers a optioal special rust ihibitig (SRI) pretreatmet (cast iro). Closers that combie the exclusive LCN powder coat fiish ad the SRI pre-treatmet exceed the ANSI stadard for corrosio resistace eve further. Plated fiishes are available as a optio to accet door ad frame for the 1460 closers. LISTINGS & APPROVALS UL listed for self-closig doors without hold-ope uder SWINGING DOOR CLOSERS (GVEV) file R 1943. Tested ad certified uder ANSI Stadard A156.4 grade oe. Cosult factory for details. Cosult factory for other listigs such as; cul, Califoria State Fire Marshal, Bureau of Stadards ad Appeals. POSITIVE PRESSURE LCN closers have bee certified for three hours by UL to be i compliace with UL 10 C. Cotact LCN for specific details o door closer fire ratigs. FASTENERS 1260, 1460, 1460T series closers are shipped with: A stadard SELF-REAMING ad TAPPING SCREW (SRT) pack that cotais Philips head SRT screws to istall the closer. 1250 ad 1450 series closers are shipped with: A uiversal screw pack to iclude self reamig ad tappig screws (SRT), machie screws ad wood screws. Stadard LCN thru bolts (TB) ca be istalled o 1-3/4 (44 mm) thick doors with 1/4-20 machie screws. Optioal thru bolt (TB) sizes are available for 1-5/8 (41 mm) or 1-3/8 (35 mm) door thickess, but this must be specified whe orderig. SPECIFICATIONS Refer to SPECIFICATIONS sectio for suggested architectural specificatios. MATERIALS High stregth cast iro (1260, 1460, 1460T) or cast alumium (1250, 1450) cylider. Forged steel mai arm for all EDA, Cush, 1460HD ad 1460T Arms. Oe piece forged steel pisto. Heat treated piio. LCN's stadard all weather fluid performs to temperature rages from 120 F (49 C) to -30 F (-35 C). High efficiecy, full complemet, low frictio bearigs. Tamper resistat regulatig screws. Full rack ad piio hydraulic actio. Quiet, low frictio track ad roller combiatio for all sigle lever arm closers. FINISHES Available i six stadard or a wide selectio of optioal custom powder coat fiishes to bled with door ad frame. Drill 25/64 for steel doors or Drill 3/8 for wood doors Notes: 1. For Thru Bolts, specify door thickess if other tha 1-3/4 (44 mm). Represeted i diagram as dimesio X. 2. Phillips head, metric machie screws are available, please specify. 3. LCN recommeds the use of wood screws i wood door applicatios. MAINTENANCE Closers mouted accordig to LCN istallatio istructios require o periodic maiteace or adjustmets.. 2 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1250 Features The 1250 cast alumium closer is desiged for low-frequecy ad low abusive traffic areas. This cast alumium closer is ideal for alumium storefrots, iterior offices ad may other applicatios. Combiig depedable operatio, low maiteace ad a pateted stylish look - with or without the optioal slim lie cover. Ad with the most commo hole patter i the idustry, the 1250 is the perfect choice for easy aftermarket replacemet. Certificatios Body Costructio Fluid Hadig Grade 1 - ANSI A156.4, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy America Act Cast Alumium Body Full Complemet Bearig 1-3/8 Diameter Pisto 5/8 Diameter Sigle Heat Treated Piio Joural All Weather Fluid No-Haded Templatig Peel--Stick templates - 3/4 x 9-1/16 Moutig Hole Patter Size Adjustable Sprig Size 1-5 Warraty 15 years Cover Fasteers Moutig Arms Fiishes/Colors/ Powder Coat Slim Lie Cover, Optioal Uiversal Screw Pack (UNIV) Hige (Pull Side), Top Jamb (Push Side), Parallel Arm (Push Side) Tripack icludes Regular, Top Jamb, ad Parallel Arm (Rw/PA) Alumium (689) Statuary Broze (690) Light Broze (691) Black (693) Dark Broze (695) Brass (696) Custom colors optioal Optioal SRI primer - powder coat oly Special Templates Customized istallatio templates or products may be available to solve uusual applicatios. Cotact LCN Product Support for assistace. HINGE (PULL) SIDE MOUNTING TOP JAMB (PULL) TOP JAMB (PUSH) PARALLEL ARM STOP FACE PAINT POWDER COAT PLATED FINISH PLASTIC METAL COVER NON-HANDED NON-SIZED ACCESSIBILITY CYLINDER DELAYED ACTION REGULAR (DOUBLE) *ARM FUNCTION STANDARD (SINGLE) HEAVY DUTY HOLD-OPEN EDA/HEDA CUSH/HCUSH SCUSH/SHCUSH 180 180 180 110 110 AVAILABLE NOT AVAILABLE Closer available with less tha 5.0 lbs. opeig force o 36 door. * Maximum opeig/hold-ope poit with stadard template. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 3
1250 Moutig details Hige (Pull) Side Moutig 1-1/2" 38 mm 2-11/16" 68 mm B 3-1/16" 78 mm A 3-3/16" 81 mm 11-3/4" 298 mm 2-3/8" 60 mm 9-11/16" 246 mm Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded at hold-ope poit or where a door caot swig 180 Reveal Should ot exceed 3/4 (19 mm) for regular arm or 1/2 (13 mm) for hold-ope arm Top Rail Less tha 2-3/8 (60 mm) requires PLATE, 1250-18 Clearace 3-1/16 (78mm) behid door required for istallatio. Maximum opeig 100 : A = 6-11/16 (170mm) B = 12-7/16 (316 mm) 101 to 120 : A= 5-11/16 (144mm) B = 11-7/16 (291 mm) or *121 to 180 : A= 3-1/16 (78 mm) B = 8-15/16 (227 mm) Hold-ope poits up to maximum opeig with hold-ope arm *Frame ad trim permittig. 4 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1250 Moutig details Top Jamb (Push Side) Moutig 9-11/16" 246 mm 1-15/16" 49 mm A 3-1/16" 78 mm 2-9/16" 65 mm 11-3/4" 298 mm B 2-11/16" 68 mm 1-13/16" 46 mm Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded at hold-ope poit or where a door caot swig 180 Reveal Arm Type Maximum Reveal Opeig Regular Arm 0 to 5 180 Log Arm 4 to 8 165 Hold-Ope Arm 0 to 2-3/4 180 Log Hold-Ope Arm 2 to 6-1/2 180 Top Rail Requires 1-3/4 (44 mm) miimum. 2-1/2 (64 mm) miimum with closer o PLATE, 1250-18 Head Frame Less tha 1-3/4 (44 mm) requires PLATE, 1250-18. For flush ceilig coditio with 2 (51 mm) head frame, use PLATE, 1250-18. (Plate requires 1-3/8 (35 mm) miimum.) Maximum opeig 100 : A = 7-3/16 (183 mm) B = 12-15/16 (329 mm) 101 to 120 : A= 5-11/16 (144 mm) B = 11-7/16 (291 mm) or *121 to 180 : A= 3-1/16 (78 mm) B = 8-15/16 (227 mm) Hold-ope poits up to maximum opeig with hold-ope arm *Frame ad trim permittig. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 5
1250 Moutig details Parallel Arm (Push Side) Moutig B 4" 102 mm 4-1/2 114mm 5-5/16" 135 mm 3-1/16" 78 mm 4-1/8" 105 mm A 9-11/16" 246 mm 16-11/16" 424 mm The 'A' dimesio refers to the edge of the closer body to the ceter lie of pivot or hige. The 'B' dimesio refers to the edge of the closer shoe bracket to the ceter lie of pivot or hige. Butt Higes Auxiliary Stop Top Rail Clearace Stop Width Should ot exceed 5 (127 mm) i width Recommeded at hold-ope poit, where a door caot swig 180, or where CUSH-N-STOP arm is ot used Less tha 4-1/2 (114 mm) measured from the stop requires PLATE, 1250-18PA 1250-62PA shoe projects 4-1/8 (105 mm) from door face Miimum 1 (25 mm) Blade Stop Clearace, requires 1/2 (13 mm) BLADE STOP SPACER, 1250-61 Auxiliary Shoe Maximum opeig 1250-62A allows istallatio of regular arm with overhead holder/stop Regular or hold-ope arm ca be templated to 100 : A = 7-5/16 (186 mm) B = 8-5/8 (219 mm) or 101 to 130 : A= 5-13/16 (148 mm) B = 7-1/8 (181 mm) or *131 to 180 : A= 3-13/16 (97 mm) B = 5-1/8 (130 mm) Hold-ope poits up to maximum opeig with hold-ope arm. *Frame ad trim permittig. Note: 1250 Parallel arm closer icludes 1250-201 FIFTH HOLE SPACER to support PA SHOE 6 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
EDA mout B 4" 102 mm 1250 4" 102 mm A 9-11/16" 246 mm 4-13/16" 122 mm 3-1/16" 78 mm 17" 433 mm 5-11/16" 144 mm Moutig details EDA ad CUSH -N-STOP moutig CUSH/SCUSH mout B 4" 102 mm 4" 102 mm A 9-11/16" 246 mm 4-13/16" 122 mm 3-1/16" 78 mm 17" 433 mm The 'A' dimesio refers to the edge of the closer body to the ceter lie of pivot or hige. The 'B' dimesio refers to the edge of the closer shoe bracket to the ceter lie of pivot or hige. Clearace 1250-62EDA or CUSH shoe projects 5-11/16 (144mm) from door face Head Frame Flush or rabbeted requires CUSH FLUSH PANEL ADAPTER, 1250-419 EDA or CUSH ARM Sprig CUSH Maximum opeig Requires soffit SHOE SUPPORT, 1250-30 for fifth screw achorage where reveal is less tha 2-3/4 (70mm) Dead stop poits are approximately 5 more tha templated stop poit. EDA template allows 180. Hold-ope poit up to maximum opeig 100 : A = 7-5/16 (186mm) B = 9 (229 mm) or 130 : A = 5-13/16 (148 mm) B = 7-1/2 (191 mm) or 180 : A = 3-13/16 (97 mm) B = 5-1/2 (140 mm) Note: 1250 closers ordered with EDA, CUSH or SPRING CUSH arms iclude 1250-201 FIFTH HOLE SPACER to support the shoe CUSH arms ca be templated for maximum opeig/ hold-ope poit at 85 85 : A = 8-13/16 (224 mm) B = 10-1/2 (267 mm) 90 : A = 8-1/16 (205 mm) B = 9-3/4 (248 mm) 100 : A = 6-11/16 (170 mm) B = 8-3/8 (213 mm) 105 : A = 6-1/16 (154 mm) B = 7-3/4 (197 mm) 110 : A = 5-7/16 (138 mm) B = 7-1/8 (181 mm) LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 7
1250 Accessories Cyliders Covers 1250-3071 Cast Alumium Cylider Assembly No-Haded Stadard 1250-72 Slim Lie Plastic Cover No-Haded Optioal Istallatio Accessories 1250-18 Plate 1250-18PA Plate 1250-30 CUSH Shoe Support 1250-61 Blade Stop Spacer Required for hige side mout where top rail is less tha 2-3/8 (60mm) Required for top jamb moutig where head frame is less tha 1-3/4 (44 mm) or flush ceilig coditio exists Required for parallel arm moutig where top rail is less tha 4-1/2 (114mm), measured from the stop Requires 1-3/4 (44 mm) miimum top rail Provide achorage for fifth screw used with CUSH arms where reveal is less tha 2-3/4 (70mm) Lowers parallel arm shoe to clear 1/2 (13 mm) blade stop Requires miimum 1-1/2 (38 mm) miimum top rail or 1-1/4 (32 mm) head frame 1250-62A Auxiliary Shoe 1250-419 PA Flush Pael Adapter 1250-62PA PA Shoe Requires a top rail of 7-1/8 (181mm). Optioal shoe replaces -62PA for parallel arm moutig of regular arm with overhead holder/stop Provides horizotal moutig surface for PA, EDA or CUSH shoe o sigle rabbeted or flush frame Required for parallel arm moutig 8 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1250 Accessories Arms 1250-3077 Regular Arm w/pa 1250-3077L Log Arm 1250-3077EDA Extra Duty Arm 1250-3049EDA Hold-Ope Extra Duty Arm No-haded No-haded No-haded Haded Mouts hige side or top jamb Parallel Arm icludes PA SHOE, 1250-62PA required for parallel arm moutig Icludes LONG ROD AND SHOE, 1250-79LR for top jamb mout with deep reveals Optioal Features solid forged steel mai ad forearm for potetially abusive istallatios Optioal Provides hold-ope fuctio adjustable at shoe Optioal 1250-3049 Hold-Ope Arm w/ PA 1250-3049L Log Hold-Ope Arm 1250-3077CNS Cush--Stop Arm 1250-3049CNS HCUSH Arm No-haded No-haded No-haded No-haded Mouts hige side, top jamb or parallel arm (62PA required) Hold-ope adjustable at shoe Optioal Icludes LONG HEAD AND TUBE, 1250-3048L for top jamb mout with deep reveals Optioal Features solid forged steel mai arm ad forearm with stop i soffit shoe Optioal Provides hold-ope fuctio with templated stop/hold-ope poits. Hadle cotrols hold-ope fuctio Optioal 1250-3077SCNS Sprig CUSH Arm 1250-3049SCNS Sprig HCUSH Arm No-haded No-haded For abusive applicatios features solid forged steel mai arm ad forearm with sprig loaded stop i the soffit shoe For abusive applicatios features solid forged steel mai arm ad forearm with sprig loaded stop i the soffit shoe Optioal Hadle cotrols hold-ope fuctio Optioal LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 9
1250 Orderig Iformatio How-to-order 1250 closers Select fiish Stadard Powder Coat Alumium, Dark Broze, Statuary, Light Broze, Black, Brass Closer will be shipped with: - Stadard cylider - Tri pack arm (Rw/PA) - Uiversal screw pack uless optios listed below are selected. Closer optios Cover Slim lie cover (SLIM) Fiish Custom Powder Coat (RAL) SRI primer Arm Regular w/62pa (Rw/PA) Log (LONG) Regular w/62a (R/62A) Hold-Ope w/62pa (Hw/PA) Log Hold-Ope (HLONG) Extra Duty (EDA) Hold-Ope Extra Duty (HEDA) - specify hadig Cush-N-Stop (CUSH) HCush (HCUSH) Sprig CUSH (SCUSH) Sprig HCUSH (SHCUSH) Optioal screw packs TORX Machie Screw (TORX) TB* & TORX Machie Screw (TBTORX) * Specify door thickess if other tha 1-3/4 Table of sizes Istallatio accessories Plate, 1250-18 Plate, 1250-18PA CUSH Shoe Support, 1250-30 Blade Stop Spacer, 1250-61 Auxiliary Shoe, 1250-62A PA Flush Pael Adapter, 1250-419 Special template ST- Meets Buy America Act BAA Select closer based o width of door. The sprig power of a 1250 cylider is field adjustable from size 1 through size 5 ad is shipped adjusted to size 3. Exterior (ad Vestibule) door width Iterior door width 24 610mm 30 762mm 36 914mm 42 1067mm 24 610mm 34 864mm 38 965mm 48 1219mm 54 1372mm *1250 size 3 size 4 size 5 *1250 size 2 size 3 size 4 size 5 Miimum door width Miimum door width Idicates recommeded rage of door width for closer size. * Adjustable Size 1 thru 5. Reduced opeig force 1250 closers CAUTION! Ay maual door closer, icludig those certified by BHMA to coform to ANSI Stadard A156.4, that is selected, istalled ad adjusted based o ADA or other reduced opeig force requiremets may ot provide sufficiet power to reliably close ad latch a door. Refer to POWER OPERATORS sectio for iformatio o systems that meet reduced opeig force requiremets without affectig closig power. * Maximum opeig force. DOOR WIDTH 36 42 48 8.5* lbs. 1250 1250 1250 5.0* lbs. 1250 1250 1250 10 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 5/16
1260 Features The 1260 is a light to medium duty cast iro closer desiged to fit ito the most commo commercial foot prit. The 1260 is adjustable for sprig sizes 1-5. The 1260 also features a complete lie of regular ad extra duty arms, LCN s peel--stick istallatio templates, a coveiet sprig adjust poiter, ad a optioal Quick Fix bracket kit. Certificatios Body Costructio Fluid Hadig Grade 1 - ANSI A156.4, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy America Act Cast Iro Body Full Complemet Bearig 1-3/8 Diameter Pisto 5/8 Diameter Sigle Heat Treated Piio Joural All Weather Fluid No-Haded Templatig Peel--Stick templates - 3/4 x 9-1/16 Moutig Hole Patter Size Adjustable Sprig Size 1-5 Warraty 20 years Cover Fasteers Moutig Arms Fiishes/Colors/ Powder Coat Slim Lie Cover, Optioal Self Reamig ad Tappig Screws (SRT) Hige (Pull Side), Top Jamb (Push Side), Parallel Arm (Push Side) Regular Arm Alumium (689) Statuary Broze (690) Light Broze (691) Black (693) Dark Broze (695) Brass (696) Custom colors optioal Optioal SRI primer - powder coat oly Special Templates Customized istallatio templates or products may be available to solve uusual applicatios. Cotact LCN Product Support for assistace. MOUNTING HINGE (PULL) SIDE TOP JAMB (PULL) TOP JAMB (PUSH) PARALLEL ARM STOP FACE POWDER COAT PLATED FINISH PLASTIC METAL COVER DESIGNER SERIES NON-HANDED NON-SIZED ACCESSIBILITY CYLINDER DELAYED ACTION REGULAR (DOUBLE) *ARM FUNCTION STANDARD (SINGLE) HEAVY DUTY HOLD-OPEN EDA/HEDA CUSH/HCUSH SCUSH/SHCUSH 180 180 120 110 110 AVAILABLE NOT AVAILABLE Closer available with less tha 5.0 lbs. opeig force o 36 door. * Maximum opeig/hold-ope poit with stadard template. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 5/16 11
1260 Moutig details Hige (Pull) Side Moutig A 2-7/8" 73 mm 2-1/2" 64 mm B 2-11/16" 68 mm 1-1/4" 32 mm 3-3/8" 86 mm 12" 305 mm 9-15/16" 252 mm 1260-18 Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded at hold-ope poit or where a door caot swig 180 Reveal Should ot exceed 3/4 (19 mm) for regular arm or 1/2 (13 mm) for hold-ope arm Top Rail Less tha 2-1/2 (64 mm) requires PLATE, 1260-18 Clearace 2-7/8 (73 mm) behid door required for istallatio Maximum opeig 110 : A = 6-9/16 (167 mm) B = 12-7/16 (316 mm) 101 to 120 : A= 5-9/16 (141 mm) B = 11-7/16 (291 mm) or *121 to 180 : A= 3-1/16 (78 mm) B = 8-15/16 (227 mm) Hold-ope poits up to maximum opeig with hold-ope arm *Frame ad trim permittig. 12 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1260 Moutig details Top Jamb (Push Side) Moutig 9-15/16" 252 mm A 2-7/8" 73 mm 2-5/8" 67 mm B 2-11/16" 68 mm 1-7/8" 48 mm 1-7/8" 48 mm 12" 305 mm 1260-18 Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded at hold-ope poit or where a door caot swig 180 Reveal Arm Type Maximum Reveal Opeig Regular Arm 3-1/2 Up to 120 Regular Arm 2-1/4 121 to 180 Log Arm 7-1/2 Up to 120 Log Arm 3-1/2 121 to 180 Hold-Ope Arm 2 Up to 120 Hold-Ope Arm 2-1/4 121 to 180 Log Hold-Ope Arm 4-1/2 Up to 120 Log Hold-Ope Arm 4-1/2 121 to 160 Top Rail 1-3/4 (44 mm) miimum. 2-1/2 (64 mm) miimum with closer o PLATE, 1260-18 Head Frame Less tha 1-3/4 (44 mm) requires PLATE, 1260-18. For flush ceilig coditio with 2 (51 mm) head frame, use PLATE, 1260-18. (Plate requires 1-3/8 (35 mm) miimum.) Maximum opeig 110 : A = 7-1/16 (179 mm) B = 12-15/16 (329 mm) 101 to 120 : A= 5-9/16 (141 mm) B = 11-7/16 (291 mm) or *121 to 180 : A= 3-1/16 (78 mm) B = 8-15/16 (227 mm) Hold-ope poits up to maximum opeig with hold-ope arm *Frame ad trim permittig. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 13
1260 Moutig details Parallel Arm (Push Side) Moutig B 4" 102 mm 5-1/4" 133 mm A 4-1/2" 114 mm 9-15/16" 252 mm 2-7/8" 73 mm 16-1/4" 413 mm 4" 102 mm 1260-18PA Butt Higes Auxiliary Stop Top Rail Clearace Stop Width Should ot exceed 5 (127 mm) i width Recommeded at hold-ope poit, where a door caot swig 180, or where CUSH-N-STOP arm is ot used Less tha 4-3/8 (111 mm) measured from the stop requires PLATE, 1260-18PA 1260-62PA shoe projects 4 (102 mm) from door face Miimum 1 (25 mm) Blade Stop Clearace, requires 1/2 (13 mm) BLADE STOP SPACER, 1260-61 Auxiliary Shoe Maximum opeig 1260-62A allows istallatio of regular arm with overhead holder/stop. Special templatig required Regular or hold-ope arm ca be templated to 100 : A = 7-3/16 (183 mm) B = 8-5/8 (219 mm) or 101 to 130 : A= 5-11/16 (144 mm) B = 7-1/8 (181 mm) or *131 to 180 : A= 3-11/16 (94 mm) B = 5-1/8 (130 mm) Hold-ope poits up to maximum opeig with hold-ope arm. *Frame ad trim permittig. Notes: Optioal moutig requires PA SHOE, 1260-62PA for REGULAR or HOLD-OPEN arms 1260 Parallel arm closer icludes 1260-201 FIFTH HOLE SPACER to support PA SHOE 14 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
EDA mout 2-7/8" 73 mm B 4" 102 mm 4-1/2" 5-1/4" 114 mm 133 mm 16" 406 mm 5-1/2" 140 mm A 9-15/16" 252 mm 1260 Moutig details EDA ad CUSH moutig 1260-18PA CUSH mout B 2-7/8" 73 mm 4" 102 mm 5-1/2" 140 mm 5-1/4" 133 mm A 4-1/2" 114 mm 9-15/16" 252 mm 16" 406 mm 1260-18PA Clearace 1260-62EDA or CUSH shoe projects 5-1/2 (140 mm) from door face Head Frame Flush or rabbeted requires CUSH FLUSH PANEL ADAPTER, 1260-419 EDA or CUSH ARM Maximum opeig Requires SHOE SUPPORT, 1260-30 for fifth screw achorage where reveal is less tha 3-1/16 (78 mm) EDA template allows 120. Hold-ope poit up to maximum opeig 90 : A = 4-13/16 (122 mm) B = 9-1/2 (241 mm) or 120 : A = 3-5/16 (84 mm) B = 8 (203 mm) Hold-ope poits up to maximum opeig with HEDA arm Note: 1260 closers ordered with EDA, CUSH or SPRING CUSH arms iclude 1260-201 FIFTH HOLE SPACER to support the shoe. CUSH arms ca be templated for maximum opeig/ hold-ope poit at 85 : A = 5-5/16 (135 mm) B = 10 (254 mm) 90 : A = 4-11/16 (119 mm) B = 9-3/8 (238 mm) 100 : A = 3-9/16 (90 mm) B = 8-1/4 (210 mm) 110 : A = 2-13/16 (71 mm) B = 7-1/2 (191 mm) LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 15
1260 Accessories Cyliders Covers 1261(2)(3)(4)(5)-3071 Cast Iro Cylider Assembly No-haded Stadard 1260-72 Slim Lie Plastic Cover No-haded Optioal Istallatio Accessories 1260-18 Plate 1260-18PA Plate 1260-18QF Quick Fix Bracket Kit 1260-30 CUSH Shoe Support Required for hige side mout where top rail is less tha 2-1/2 (64 mm) Required for top jamb moutig where head frame is less tha 1-3/4 (44 mm) or flush ceilig coditio exists Required for parallel arm moutig where top rail is less tha 4-3/8 (111 mm), measured from the stop Requires 1-3/4 (44 mm) miimum top rail Optioal kit icludes retro-fit moutig plates for 1371 closer cylider ad shoe Useful i applicatios whe previously drilled holes are damaged Provide achorage for fifth screw used with CUSH arms where reveal is less tha 3-1/16 (78 mm) Requires miimum 1-1/2 (38 mm) miimum top rail or 1-1/4 (32 mm) head frame 1260-61 Blade Stop Spacer 1260-62A Auxiliary Shoe 1260-419 PA Flush Pael Adapter 1260-62PA PA Shoe Lowers parallel arm shoe to clear 1/2 (13 mm) blade stop Requires a top rail of 7 (178 mm) Optioal shoe replaces-62pa for parallel arm moutig of regular arm with overhead holder/stop Provides horizotal moutig surface for PA, EDA or CUSH shoe o sigle rabbeted or flush frame Required for parallel arm moutig 16 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1260 Accessories Arms 1260-3077 Regular Arm 1260-3077L Log Arm 1260-3049 Hold-ope Arm No-haded No-haded No-haded Mouts hige side or top jamb Parallel Arm icludes PA SHOE, 1260-62PA required for parallel arm moutig Icludes LONG ROD AND SHOE, 1260-79LR for top jamb mout with deep reveals Optioal Mouts hige side, top jamb or parallel arm (62PA required) Hold-ope adjustable at shoe Optioal 1260-3049L Log Hold-ope Arm 1260-3077EDA Extra Duty Arm 1260-3077EDA/62G Extra Duty Arm w/ 62G 1260-3049EDA Hold-Ope Extra Duty Arm No-haded No-haded No-haded Haded arm Icludes LONG HEAD AND TUBE, 1260-3048L for top jamb mout with deep reveals Optioal Features solid forged steel mai ad forearm for potetially abusive istallatios Optioal 1260-3077EDA/G for blade stop clearace Features solid forged steel mai ad forearm for potetially abusive istallatios Provides hold-ope fuctio adjustable at shoe Optioal 1260-3077CNS Cush--Stop Arm 1260-3049CNS HCUSH Arm No-haded No-haded Features solid forged steel mai arm ad forearm with stop i soffit shoe Optioal Provides hold-ope fuctio with templated stop/hold-ope poits. Hadle cotrols hold-ope fuctio Optioal LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 17
1260 Orderig Iformatio How-to-order 1260 closers Select fiish Stadard Powder Coat Alumium, Dark Broze, Statuary, Light Broze, Black, Brass Closer will be shipped with: - Stadard cylider - Regular arm - Self-reamig ad tappig screws uless optios listed below are selected. Closer optios Cover Slim lie cover (SLIM) Fiish Custom Powder Coat (RAL) SRI primer (for use with powder coat fiishes oly) Arm Regular w/62pa (Rw/PA) Log (LONG) Regular w/62a (R/62A) Hold-Ope (H) Hold-Ope w/62pa (Hw/PA) Log Hold-Ope (HLONG) Extra Duty (EDA) (optioal -62G) Hold-Ope Extra Duty (HEDA) - specify hadig (optioal -62G) Cush-N-Stop (CUSH) HCush (HCUSH) Optioal screw packs TB* w/self-reamig ad Tappig Screws (TBSRT) Wood & Machie Screw (WMS) TB*, Wood & Machie Screw (TBWMS) TORX Machie Screw (TORX) TB* & TORX Machie Screw (TBTORX) * Specify door thickess if other tha 1-3/4 Table of sizes Istallatio accessories Plate, 1260-18 Plate, 1260-18PA CUSH Shoe Support, 1260-30 Blade Stop Spacer, 1260-61 Auxiliary Shoe, 1260-62A PA Flush Pael Adapter, 1260-419 Quick Fix Bracket Kit, 1260-18QF Special template ST- Select closer based o width of door. The sprig power of a 1261 cylider is field adjustable from size 1 through size 5 ad is shipped adjusted to size 3. Exterior (ad Vestibule) door width Iterior door width 24 610mm 30 762mm 36 914mm 42 1067mm 24 610mm 34 864mm 38 965mm 48 1219mm 54 1372mm *1261 size 3 size 4 size 5 *1261 size 2 size 3 size 4 size 5 Miimum door width Miimum door width Idicates recommeded rage of door width for closer size. * Adjustable Size 1 thru 5. Reduced opeig force 1260 closers CAUTION! Ay maual door closer, icludig those certified by BHMA to coform to ANSI Stadard A156.4, that is selected, istalled ad adjusted based o ADA or other reduced opeig force requiremets may ot provide sufficiet power to reliably close ad latch a door. Refer to POWER OPERATORS sectio for iformatio o systems that meet reduced opeig force requiremets without affectig closig power. * Maximum opeig force. DOOR WIDTH 36 42 48 8.5* lbs. 1261 1261 1261 5.0* lbs. 1261 1261 1261 18 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1450 Features The 1450 cast alumium closer was specially desiged to deliver cosistet, depedable, log-term performace i frequetly-used, low-abusive traffic areas. The pateted desig, featurig the idustry's most commo hole patter, is a excellet choice for a rage of applicatios - from aftermarket replacemet to alumium store frots, to ew costructio projects - aywhere quality, reliability ad value are importat. Certificatios Body Costructio Fluid Hadig Grade 1 - ANSI A156.4, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy America Act Cast Alumium Body Full Complemet Bearig 1-1/4 Diameter Pisto 5/8 Diameter Sigle Heat Treated Piio Joural All Weather Fluid No-Haded Templatig Peel--Stick templates - 3/4 x 12 Moutig Hole Patter Size Adjustable Sprig Size 1-6 Warraty 25 years Cover Fasteers Moutig Arms Fiishes/Colors/ Powder Coat Slim Lie Plastic, Stadard Full Plastic ad Metal, Optioal Uiversal Screw Pack (UNIV) Hige (Pull Side), Top Jamb (Push Side), Parallel Arm (Push Side) Stadard regular pull side, ad top jamb Alumium (689) Statuary Broze (690) Light Broze (691) Black (693) Dark Broze (695) Brass (696) Custom colors optioal Optioal SRI primer - powder coat oly Optioal plated fiishes Special Templates Customized istallatio templates or products may be available to solve uusual applicatios. Cotact LCN Product Support for assistace. HINGE (PULL) SIDE MOUNTING TOP JAMB (PULL) TOP JAMB (PUSH) PARALLEL ARM STOP FACE PAINT POWDER COAT PLATED FINISH PLASTIC METAL COVER NON-HANDED NON-SIZED ACCESSIBILITY CYLINDER DELAYED ACTION REGULAR (DOUBLE) STANDARD (SINGLE) HOLD-OPEN * *ARM FUNCTION EDA/HEDA * 180 180 180 110 110 CUSH/HCUSH SCUSH/SHCUSH AVAILABLE NOT AVAILABLE Closer available with less tha 5.0 lbs. opeig force o 36 door. * Maximum opeig/hold-ope poit with stadard template. D = For desiger series oly. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 19
1450 Moutig details Hige (Pull) Side Moutig 2-15/16" 75 mm 3/4" 19 mm B 2-11/16" 68 mm 1-3/8" 35 mm 11-13/16" 300 mm 2-11/16" 68 mm A 2-1/8" 54 mm 13-1/16" 332 mm REGULAR-PULL SIDE The 'A' dimesio refers to the edge of the closer body to the ceter lie of pivot or hige. The 'B' dimesio refers to the edge of the closer shoe bracket to the ceter lie of pivot or hige. Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded at hold-ope poit or where a door caot swig 180 Reveal Should ot exceed 3/4 (19 mm) for regular arm or 1/2 (13 mm) for hold-ope arm Top Rail Less tha 2-1/2 (64 mm) requires PLATE, 1450-18 With Full cover, use PLATE, 1450-18FC. Plate requires 1-1/2 (38 mm) miimum Clearace Delayed Actio 2-3/8 (60 mm) behid door required for istallatio Delays closig from 180-70. Delay time adjustable up to approximately 1 miute Maximum opeig 100 : A = 7 (102 mm) B = 12-3/8 (314 mm) 101 to 130 : A=5-1/2 (140 mm) B = 10-7/8 (276 mm) 131 to 180 : A=4 (140 mm) B = 9-3/8 (238 mm) Hold-ope poits up to maximum opeig with hold-ope arm *Frame ad trim permittig. 20 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1450 Moutig details Top Jamb (Push Side) Moutig 2-9/16" 65 mm A 11-3/4" 299 mm B 3/4" 19 mm 1-5/8" 42 mm 2-11/16" 68 mm 13-1/16" 332 mm The 'A' dimesio refers to the edge of the closer body to the ceter lie of pivot or hige. The 'B' dimesio refers to the edge of the closer shoe bracket to the ceter lie of pivot or hige. Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded at hold-ope poit or where a door caot swig 180 Reveal Arm Type Reveal Max Opeig Regular Arm 5 Up to 170 Regular Arm 3-3/4 Up to 180 Log Arm 8 Up to 155 Hold-Ope Arm 2-3/4 Up to 180 Log Hold-Ope Arm 4-7/8 Up to 140 Top Rail Requires 2-1/8 (54 mm) miimum. 3-3/8 (86 mm) miimum with closer o PLATE, 1450-18. Head Frame Delayed Actio Less tha 1-3/4 (44 mm) requires PLATE, 1450-18. For flush ceilig coditio with 1-3/4 (45 mm) head frame, use PLATE, 1450-18 Delays closig from 180-70. Delay time adjustable up to approximately 1 miute Maximum opeig 100 : A=7 (102 mm) B = 12-3/8 (314 mm) 101 to 130 : A= 5-1/2 (140 mm) B = 10-7/8 (276 mm) 131 to 180 : A= 4 (102 mm) B = 9-3/8 (238 mm) Hold-ope poits up to maximum opeig with hold-ope arm. *Frame ad trim permittig. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 21
1450 Moutig details Parallel Arm (Push Side) Moutig B 4" 102 mm 5-3/8" 136 mm A 2-1/8" 54 mm 20-3/8" 517 mm 4-1/8" 105 mm 13-1/16" 332 mm Butt Higes Auxiliary Stop Top Rail Should ot exceed 5 (127 mm) i width Recommeded at hold-ope poit, where a door caot swig 180, or where CUSH-N-STOP arm is ot used Less tha 5-1/4 (133 mm) measured from the soffit requires Plate requires 1-1/4 (32 mm) miimum. Clearace Cover Miimum Top Rail (measured from soffit) Plate Required Plastic 3-1/2 (89 mm) 1450-18 2-1/4 (57 mm) 1450-18PA Metal 3-1/2 (89 mm) 1450-18FC 2-1/4 (57 mm) 1450-18PAFC 1450-62PA shoe projects 4-1/8 (105 mm) from door face Head Frame Flush or sigle rabbeted requires PA SHOE ADAPTER, 1450-418 Stop Width Miimum 1 (25 mm) Blade Stop Clearace, requires 1/2 (13 mm) BLADE STOP SPACER, 1450-61 Auxiliary Shoe Delayed Actio Maximum opeig 1450-62A allows istallatio of regular arm with overhead holder/stop Delays closig from 180-70. Delay time adjustable up to approximately 1 miute Regular or hold-ope arm ca be templated to 120 : A = 3-3/16 (81 mm) B = 8-7/8 (225 mm) 121 to 180 : A= 11/16 (17 mm) B = 6-3/8 (162 mm) Notes: PA shoe is icluded with Rw/PA Arm 1450 closer icludes 1450-201 FIFTH HOLE SPACER to support PA SHOE Hold-ope poits up to maximum opeig with hold-ope arm. 22 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
EDA/HEDA mout A 4" 102 mm 1450 2-11/16" 68 mm 20-13/16" 528 mm 5-11/16" 145 mm B 13-1/16" 332 mm 2-1/8" 54 mm 4-9/16" 116 mm Moutig details EDA ad CUSH -N-STOP moutig CUSH/HCUSH/SCUSH /SHCUSH mout A 4" 102 mm 2-11/16" 68 mm 20-13/16" 528 mm 5-11/16" 145 mm B 13-1/16" 332 mm 2-1/8" 54 mm 4-9/16" 116 mm The 'A' dimesio refers to the edge of the closer body to the ceter lie of pivot or hige. The 'B' dimesio refers to the edge of the closer shoe bracket to the ceter lie of pivot or hige. Clearace 1450-62EDA or CUSH shoe projects 5-11/16 (144mm) from door face Head Frame Flush or rabbeted requires CUSH FLUSH PANEL ADAPTER, 1450-419 EDA or CUSH ARM Sprig CUSH Maximum opeig Requires soffit SHOE SUPPORT, 1450-30 for fifth screw achorage where reveal is less tha 3-1/16 (78 mm) Dead stop poits are approximately 5 more tha templated stop poits EDA template allows 110. Hold-ope poit up to maximum opeig 120 : A = 8-7/8 (225 mm) B = 3-3/16 (81 mm) over 120 : A = 6-3/8 (162 mm) B = 11/16 (17 mm) Note: 1450 closers ordered with EDA, CUSH or SPRING CUSH arms iclude 1450-201 FIFTH HOLE SPACER to support the shoe. CUSH arms ca be templated for maximum opeig/ hold-ope poit at 85 85 : A = 10-3/8 (279 mm) B = 4-15/16 (140 mm) 90 : A = 9-5/8 (244 mm) B = 4-3/16 (106 mm) 95 : A = 8-7/8 (225 mm) B = 3-7/16 (87 mm) 100 : A = 8-1/4 (210 mm) B = 2-13/16 (71 mm) 105 : A = 7-5/8 (194 mm) B = 2-3/16 (56 mm) 110 : A = 7 (178 mm) B = 1-9/16 (40 mm) LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 23
1450 Accessories Cyliders Covers Left had show 1450-3071 Cast Alumium Cylider Assembly 1450-72 Slim Lie Plastic Cover 1450-72MC Metal Cover 1450-72FC Full Plastic Cover No-Haded No-Haded Haded No-Haded Stadard Stadard Optioal Optioal 1450-3071DEL Cast Alumium Cylider Assembly with Delay Actio Optioal Istallatio Accessories 1450-18 / 1450-18FC Plate 1450-18PA / 1450-18PAFC Plate 1450-30 CUSH Shoe Support 1450-61 Blade Stop Spacer Required for hige side mout where top rail is less tha 2-1/2 (64 mm) Required for top jamb moutig where head frame is less tha 1-3/4 (44 mm) or flush ceilig coditio exists Requires miimum 1-1/2 (38 mm) miimum top rail or 1-1/4 (32 mm) head frame Required for parallel arm moutig where top rail is less tha 4-3/8 (111mm), measured from the stop Requires 1-3/4 (44 mm) miimum top rail With full cover, use PLATE, 1450-18FC Provide achorage for fifth screw used with CUSH arms where reveal is less tha 3-1/16 (78mm) Lowers parallel arm shoe to clear 1/2 (13 mm) blade stop. With full cover, use PLATE, 1450-18FC 1450-62PA PA Shoe 1450-62A Auxiliary Shoe 1450-419 PA Flush Pael Adapter Required for parallel arm moutig Requires a top rail of 7 (178mm). Optioal shoe replaces -62PA for parallel arm moutig of regular arm with overhead holder/stop Provides horizotal moutig surface for PA, EDA or CUSH shoe o sigle rabbeted or flush frame 24 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1450 Accessories Arms 1450-3077 Regular Arm w/pa 1450-3077L Log Arm 1450-3049 Hold-Ope Arm w/pa 1450-3049L Log Hold-Ope Arm No-Haded No-Haded No-Haded No-Haded Mouts hige side or top jamb Icludes PA SHOE, 1450-62PA required for parallel arm moutig Icludes LONG ROD AND SHOE, 1450-79LR for top jamb mout with deep reveals Optioal Mouts hige side, top jamb or parallel arm (62PA required) Hold-ope adjustable at shoe Optioal Icludes LONG HEAD AND TUBE, 1450-3048L for top jamb mout with deep reveals Optioal 1450-3077EDA Extra Duty Arm No-Haded Features solid forged steel mai ad forearm for potetially abusive istallatios Optioal 1450-3077EDA/G for blade stop clearace 1450-3077EDA/62G Extra Duty Arm w/ 62G No-Haded Features solid forged steel mai ad forearm for potetially abusive istallatios Optioal 1450-3077EDA/G for blade stop clearace 1450-3049EDA Hold-Ope Extra Duty Arm Haded arm Provides hold-ope fuctio adjustable at shoe Optioal 1450-3077CNS Cush--Stop Arm No-Haded Features solid forged steel mai arm ad forearm with stop i soffit shoe Optioal 1450-3049CNS HCUSH Arm No-Haded Provides hold-ope fuctio with templated stop/hold-ope poits Hadle cotrols hold-ope fuctio Optioal 1450-3077SCNS Sprig CUSH Arm No-Haded For abusive applicatios features solid forged steel mai arm ad forearm with sprig loaded stop i the soffit shoe Optioal 1450-3049SCNS Sprig HCUSH Arm No-Haded For abusive applicatios features solid forged steel mai arm ad forearm with sprig loaded stop i the soffit shoe Hadle cotrols hold-ope fuctio Optioal LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 25
1450 Orderig Iformatio Closer optios How-to-order 1450 closers Select fiish Stadard Powder Coat Alumium, Dark Broze, Statuary, Light Broze, Black, Brass Cylider Delayed Actio (DEL) Fiish Custom Powder Coat (RAL) (Metal cover required) Plated Fiish, US (Metal cover required) SRI primer Arm Regular w/62pa (Rw/PA) Log (LONG) Regular w/62a (Rw/62A) Hold-Ope w/62pa (Hw/PA) Log Hold-Ope (HLONG) Extra Duty (EDA) (optioal -62G) Hold-Ope Extra Duty (HEDA) - specify hadig Cush-N-Stop (CUSH) HCush (HCUSH) Sprig Cush (SCUSH) Sprig HCush (SHCUSH) Closer will be shipped with: - Stadard cylider - Stadard cover - Tri pack arm (Rw/PA) - Uiversal screw pack uless optios listed below are selected. Optioal screw packs TORX Machie Screw (TORX) TB* & TORX Machie Screw (TBTORX) * Specify door thickess if other tha 1-3/4 Table of sizes Istallatio accessories Plate, 1450-18 Plate, 1450-18FC Plate, 1450-18PA Plate, 1450-18PAFC CUSH Shoe Support, 1450-30 Blade Stop Spacer, 1450-61 Auxiliary Shoe, 1450-62A PA Flush Pael Adapter, 1450-419 Select closer based o width of door. The sprig power of a 1450 cylider is field adjustable from size 1 through size 6 ad is shipped adjusted to size 3. Special template ST- Meets Buy America Act BAA Exterior (ad Vestibule) door width Iterior door width 24 610mm 30 762mm 36 914mm 42 1067mm 48 1219mm 24 610mm 34 864mm 38 965mm 48 1219mm 54 1372mm 60 1524mm *1450 size 3 size 4 size 5 size 6 *1450 size 2 size 3 size 4 size 5 size 6 Miimum door width Miimum door width Idicates recommeded rage of door width for closer size. * Adjustable Size 1 thru 6. Reduced opeig force 1450 closers CAUTION! Ay maual door closer, icludig those certified by BHMA to coform to ANSI Stadard A156.4, that is selected, istalled ad adjusted based o ADA or other reduced opeig force requiremets may ot provide sufficiet power to reliably close ad latch a door. Refer to POWER OPERATORS sectio for iformatio o systems that meet reduced opeig force requiremets without affectig closig power. * Maximum opeig force. DOOR WIDTH 36 42 48 8.5* lbs. 1450 1450 1450 5.0* lbs. 1450 1450 1450 26 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1460 Features Desiged for maximum versatility, the 1460, available with multiple cover optios, ca be used for both commercial ad istitutioal applicatios. This fully uiversal closer offers a wide variety of optios ad fast ad accurate istallatio. Certificatios Body Costructio Fluid Hadig Grade 1 - ANSI A156.4, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy America Act Cast Iro Body Full Complemet Bearig 1-1/4 Diameter Pisto 3/4 Diameter Sigle Heat Treated Piio Joural All Weather Fluid No-Haded Templatig Peel--Stick templates - 1 x 7-1/2 Moutig Hole Patter Size Warraty Adjustable Sprig Size 1-6. Icludes Pateted Gree Dial 30 years Cover Fasteers Moutig Arms Fiishes/Colors/ Powder Coat Slim Lie Plastic, Stadard Full Plastic ad Metal Desiger, Optioal Self Reamig ad Tappig Screws (SRT) Hige (Pull Side), Top Jamb (Push Side), Parallel Arm (Push Side) Stadard regular pull side, ad top jamb Alumium (689) Statuary Broze (690) Light Broze (691) Black (693) Dark Broze (695) Brass (696) Custom colors optioal Optioal SRI primer - powder coat oly Optioal plated fiishes Special Templates Customized istallatio templates or products may be available to solve uusual applicatios. Cotact LCN Product Support for assistace. MOUNTING HINGE (PULL) SIDE TOP JAMB (PULL) TOP JAMB (PUSH) PARALLEL ARM STOP FACE POWDER COAT PLATED D FINISH PLASTIC METAL COVER DESIGNER SERIES NON-HANDED NON-SIZED ACCESSIBILITY CYLINDER DELAYED ACTION *ARM FUNCTION REGULAR (DOUBLE) STANDARD (SINGLE) HEAVY DUTY HOLD-OPEN EDA/HEDA CUSH/HCUSH 180 180 180 110 100 100 SCUSH/SHCUSH AVAILABLE NOT AVAILABLE Closer available with less tha 5.0 lbs. opeig force o 36 door. * Maximum opeig/hold-ope poit with stadard template. D = For desiger series oly. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 27
1460 Moutig details Hige (Pull) Side Moutig B 2-11/16" 3/4" 1-3/8" 68 mm 19 mm 35 mm A 11-3/8" 289 mm 2-3/8" 60 mm 12-1/4" 311 mm 2" 51 mm 2-9/16" 65 mm Optioal No-haded Desiger Metal Cover 12-1/2" 318 mm 1460-18 12-3/8" 314 mm 3" 76 mm Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded at hold-ope poit or where a door caot swig 180 Reveal Should ot exceed 3/4 (19 mm) for regular arm or 1/2 (13 mm) for hold-ope arm Top Rail Less tha 2-1/2 (64 mm) requires PLATE, 1460-18 With Full cover, use PLATE, 1460-18FC. Plate requires 1-1/2 (38 mm) miimum With Desiger metal cover, use PLATE, 1460-18DS1 Clearace Delayed Actio 2-3/8 (60 mm) behid door required for istallatio Add suffix DEL to selected cylider (eg. 1461 DEL) Delays closig from: 110 to 65 (usig 110 template) 160 to 75 (usig 180 template) Delay time adjustable up to approximately 1 miute Maximum opeig 110 : A = 5-7/8 (149 mm) B = 10-7/8 (276 mm) or *180 A= 2-7/8 (73 mm) B = 7-7/8 (200 mm) Hold-ope poits up to maximum opeig with hold-ope arm *Frame ad trim permittig. 28 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1460 Moutig details A 2" 51 mm Top Jamb (Push Side) Moutig 2-3/8" 60 mm 11-3/8" 289 mm B 2-11/16" 68 mm 3/4" 19 mm 1-7/8" 48 mm 12-1/4" 311 mm Optioal No-haded Desiger Metal Cover 12-1/2" 318 mm 1461-18 12-3/8" 314 mm 3" 76 mm Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded at hold-ope poit or where a door caot swig 180 Reveal Arm Type Reveal Max Opeig Regular Arm 4-7/8 Up to 140 Regular Arm 3-1/2 Up to 180 Log Arm 7 Up to 140 Hold-Ope Arm 2-1/2 Up to 180 Log Hold-Ope Arm 4-7/8 Up to 140 Top Rail Requires 1-7/8 (48 mm) miimum. 2-3/4 (70 mm) miimum with closer o PLATE, 1460-18 Head Frame Delayed Actio Less tha 1-3/4 (44 mm) requires PLATE, 1460-18. For flush ceilig coditio with 2 (51 mm) head frame, use PLATE, 1460-18 Add suffix DEL to selected cylider (eg. 1460 DEL). Delays closig: 110 to 75 (usig 110 template) 180 to 95 (usig 180 template) Delay time adjustable up to approximately 1 miute. Maximum opeig 110 : A= 6-3/4 (169 mm) B = 11-1/4 (286 mm) 101 to 120 : A= 3 (76 mm) B = 7-1/2 (191 mm) Hold-ope poits up to maximum opeig with hold-ope arm. *Frame ad trim permittig. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 29
1460 Moutig details Parallel Arm (Push Side) Moutig B 4" 102 mm 4-3/8" 111 mm 2-3/8" 60 mm 19-1/8" 486 mm 4" 102 mm A 12-1/4" 311 mm 2" 51 mm 1460-18PA Butt Higes Auxiliary Stop Should ot exceed 5 (127 mm) i width Recommeded at hold-ope poit, where a door caot swig 180, or where CUSH-N-STOP arm is ot used Top Rail Less tha 4-3/8 (111 mm) measured from the stop requires PLATE, 1460-18PA. With Full cover, use PLATE, 1460-18PAFC Plate requires 1-3/4 (44 mm) miimum. Plate requires 1-1/4 (32 mm) miimum With Desiger metal cover, use PLATE, 1460-18PADS1 Clearace 1460-62PA shoe projects 4 (102 mm) from door face Head Frame Flush or sigle rabbeted requires PA SHOE ADAPTER, 1460-419 Stop Width Miimum 1 (25 mm) Blade Stop Clearace, requires 1/2 (13 mm) BLADE STOP SPACER, 1460-61 Auxiliary Shoe 1460-62A allows istallatio of regular arm with overhead holder/stop Special templatig required Delayed Actio Add suffix DEL to selected cylider (eg. P1460 DEL) Delays closig from maximum opeig to approximately 75 Delay time adjustable up to approximately 1 miute Maximum opeig Regular or hold-ope arm ca be templated to 100 : A = 4-1/4 (108 mm) B = 9-1/4 (235 mm) or 180 : A= 1-3/4 (44 mm) B = 6-3/4 (171 mm) Hold-ope poits up to maximum opeig with hold-ope arm. Notes: Optioal moutig requires PA SHOE, 1460-62PA for REGULAR or HOLD-OPEN arms. Add prefix P to closer descriptio (e.g. P1460) P1460 closer icludes 1460-201 FIFTH HOLE SPACER to support PA SHOE. 30 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
EDA mout 8-5/8" 219 mm 4" 102 mm 1460 2-3/8" 60 mm 19-9/16" 497 mm 1-1/4" 32 mm 5-1/2" 140 mm 12-1/4" 311 mm 2" 51 mm 4-1/4" 108 mm Moutig details EDA ad CUSH moutig 1460-18PA CUSH mout B 4" 102 mm 2-3/8" 60 mm 19-9/16" 497 mm 5-1/2" 140 mm A 12-1/4" 311 mm 2" 51 mm 4-1/4" 108 mm 1461PA-18 Sprig CUSH Clearace Hold ope poits are approximately 5 less tha dead stop poit 1460-62EDA or CUSH shoe projects 5-1/2 (140 mm) from door face Head Frame Flush or rabbeted requires PA FLUSH PANEL ADAPTER, 1460-419 EDA or CUSH ARM Requires SHOE SUPPORT, 1460-30 for fifth screw achorage where reveal is less tha 3-1/16 (78 mm) Maximum opeig EDA template allows 110 Hold-ope poit up to maximum opeig Note: 1460 closers ordered with EDA, CUSH or SPRING CUSH arms iclude 1460-201 FIFTH HOLE SPACER to support the shoe CUSH arms ca be templated for maximum opeig/hold-ope poit at 85 : A = 2-3/8 (60 mm) B = 9-9/16 (243 mm) 90 : A = 1-5/8 (41 mm) B = 9-1/16 (230 mm) 100 : A = 5/8 (16 mm) B = 8-1/16 (205 mm) LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 31
1460 Accessories Cyliders Covers 1461-3071 Cast Iro Cylider Assembly 1460-72 Slim Lie Plastic Cover 1460-72FC Full Cover 1460-72DS Desiger Metal Cover No-Haded No-Haded No-Haded No-Haded Stadard Stadard Plastic cover Optioal Provides complete eclosure with a stylish look Required for platig ad custom powder coat optio Optioal Istallatio Accessories 1460-18 Plate 1460-18DS1 Plate The followig details pertai to the above plates: Required for hige side mout where top rail is less tha 2-1/2 (64 mm) Required for top jamb moutig where head frame is less tha 1-3/4 (44 mm) or flush ceilig coditio exists Requires miimum 1-1/2 (38 mm) miimum top rail or 1-1/4 (32 mm) head frame With full cover, use PLATE, 1460-18FC With Desiger metal cover, use PLATE, 1460-18DS1 Note: 18FC ad 18DS will ot work i top jamb applicatio. 1460-18FC Plate 1460-30 Cush Shoe Support Provide achorage for fifth screw used with CUSH arm where reveal is less tha 3-1/16 (78 mm) 1460-61 Blade Stop Spacer Lowers parallel arm shoe to clear 1/2 (13 mm) blade stop 1460-30A Moutig Bracket Bracket to be used whe istallig cylider body Icluded with cylider whe ordered 1460-62A Auxiliary Shoe Requires a top rail of 7 (178 mm) Optioal shoe replaces -62PA for parallel arm moutig of regular arm with overhead holder/stop 1460-18PA Plate 1460-18PADS1 Plate The followig details pertai to the above plates: Required for parallel arm moutig where top rail is less tha 4-3/8 (111 mm), measured from the stop Requires 1-3/4 (44 mm) miimum top rail With full cover, use PLATE, 1460-18PAFC With Desiger metal cover, use PLATE, 1460-18PADS1 1460-18PAFC Plate 1460-419 PA Flush Pael Adapter Provides horizotal moutig surface for PA, EDA, or CUSH shoe o sigle rabbeted or flush frame 1460-62PA PA Shoe Required for parallel arm moutig 32 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
Arms 1460 Accessories 1460-3077 Regular Arm 1460-3077L Log Arm 1460-3077HD Heavy Duty Regular Arm No-haded No-haded No-haded Mouts hige side or top jamb P1460 closer icludes PA SHOE, 1460-62PA required for parallel arm moutig Icludes LONG ROD AND SHOE, 1460-79LR for top jamb mout with deep reveals Optioal Mouts hige side, top jamb or parallel arm Optioal 1460-3077HDL Heavy Duty Log Arm 1460-3049 Hold-Ope Arm 1460-3049L Log Hold-Ope Arm No-haded No-haded No-haded Icludes log rod ad shoe, 1460-79LR for top jamb mouts with deep reveals Optioal Mouts hige side, top jamb or parallel arm (62PA required) Hold-ope adjustable at shoe Optioal Icludes LONG HEAD AND TUBE, 1460-3048L for top jamb mout with deep reveals Optioal 1460-3077EDA Extra Duty Arm 1460-3077EDA/62G Extra Duty Arm w/ 62G 1460-3049EDA Hold-Ope Extra Duty Arm 1460-3077CNS Cush-N-Stop Arm No-haded No-haded Haded arm No-haded Features solid forged steel mai ad forearm for potetially abusive istallatios Optioal 1460-3077EDA/62G for blade stop clearace Features solid forged steel mai ad forearm for potetially abusive istallatios Provides hold-ope fuctio adjustable at shoe Optioal Features solid forged steel mai arm ad forearm with stop i soffit shoe Optioal 1460-3049CNS HCUSH Arm No-haded Provides hold-ope fuctio with templated stop/hold-ope poits Hadle cotrols hold-ope fuctio Optioal 1460-3077SCNS Sprig CUSH Arm No-haded For abusive applicatios features solid forged steel mai arm ad forearm with sprig loaded stop i the soffit shoe Optioal 1460-3049SHCNS Sprig HCUSH Arm No-haded For abusive applicatios features solid forged steel mai arm ad forearm with sprig loaded stop i the soffit shoe. Hadle cotrols hold-ope fuctio LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 Optioal 33
1460 Orderig Iformatio Closer optios How-to-order 1460 closers Select fiish Stadard Powder Coat Alumium, Dark Broze, Statuary, Light Broze, Black, Brass Closer will be shipped with: - Stadard cylider - Stadard cover - Regular arm - Self-reamig ad tappig screws uless optios listed below are selected. Cylider Delayed Actio (DEL) Cover Full cover (FC) Desiger series cover (DS) Fiish Custom Powder Coat (RAL) (DS cover required) Plated Fiish, US (DS cover required) SRI primer (for use with powder coat fiishes oly) Arm Regular w/62pa (Rw/PA) Log (LONG) Regular w/62a (Rw/62A) Hold-Ope (H) Hold-Ope w/62pa (Hw/PA) Log Hold-Ope (HLONG) Heavy Duty (HD) Heavy Duty w/62a (HD/62A) Heavy Duty w/62pa (HD/PA) Heavy Duty Log (HDL) Extra Duty Arm (EDA) (optioal -62G) Hold-Ope Extra Duty (HEDA) (specify hadig), (optioal -62G) Cush-N-Stop (CUSH) HCush (HCUSH) Sprig Cush (SCUSH) Sprig HCush (SHCUSH) Optioal screw packs TB* w/self-reamig ad Tappig Screws (TBSRT) Wood & Machie Screw (WMS) TB*, Wood & Machie Screw (TBWMS) TORX Machie Screw (TORX) TB* & TORX Machie Screw (TBTORX) * Specify door thickess if other tha 1-3/4 Table of sizes Istallatio accessories Plate, 1460-18 Plate, 1460-18DS Plate, 1460-18FC Plate, 1460-18PA Plate, 1460-18PADS Plate, 1460-18PAFC CUSH Shoe Support, 1460-30 Blade Stop Spacer, 1460-61 Auxiliary Shoe, 1460-62A PA Flush Pael Adapter, 1460-419 Select closer based o width of door The sprig power of a 1461 cylider is field adjustable from size 1 through size 6 ad is shipped adjusted to size 3 Special template ST- Exterior (ad Vestibule) door width Iterior door width 24 610mm 30 762mm 36 914mm 42 1067mm 48 1219mm 24 610mm 34 864mm 38 965mm 48 1219mm 54 1372mm 54 1524mm *1461 size 3 size 4 size 5 size 6 *1461 size 2 size 3 size 4 size 5 size 6 Miimum door width Miimum door width Idicates recommeded rage of door width for closer size. * Adjustable Size 1 thru 5. Reduced opeig force 1460 closers CAUTION! Ay maual door closer, icludig those certified by BHMA to coform to ANSI Stadard A156.4, that is selected, istalled ad adjusted based o ADA or other reduced opeig force requiremets may ot provide sufficiet power to reliably close ad latch a door. Refer to POWER OPERATORS sectio for iformatio o systems that meet reduced opeig force requiremets without affectig closig power. * Maximum opeig force. DOOR WIDTH 36 42 48 8.5* lbs. 1461 1461 1461 5.0* lbs. 1461 1461 1461 34 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1460T Features The 1460T is a fully uiversal slim lie, sigle lever (track) arm closer desiged for iterior use o arrow head frames ad top rails. The moder stylig ad small projectio make it a excellet choice for iterior doors. Certificatios Body Costructio Fluid Hadig Grade 1 - ANSI A156.4, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy America Act Cast Iro Body Full Complemet Bearig 1-1/4 Diameter Pisto 5/8 Diameter Sigle Heat Treated Piio Joural All Weather Fluid No-Haded Templatig Peel--Stick templates - 1 x 7-1/2 Moutig Hole Patter Size Adjustable No-Sized 2-4 Warraty 30 years Cover Fasteers Moutig Arms Fiishes/Colors/ Powder Coat Slim Lie, Stadard Full Plastic or Full Metal Desigers, Optioal Self Reamig ad Tappig Screws (SRT) Hige pull side, top jamb, pull stop face Sigle level with track roller Alumium (689) Statuary Broze (690) Light Broze (691) Black (693) Dark Broze (695) Brass (696) Custom colors optioal Optioal SRI primer - powder coat oly Optioal plated fiishes Special Templates Customized istallatio templates or products may be available to solve uusual applicatios. Cotact LCN Product Support for assistace. HINGE (PULL) SIDE MOUNTING TOP JAMB (PULL) TOP JAMB (PUSH) PARALLEL ARM STOP FACE PLATED POWDER COAT D FINISH PLASTIC METAL COVER DESIGNER SERIES NON-HANDED NON-SIZED ACCESSIBILITY CYLINDER DELAYED ACTION 180 115 *ARM FUNCTION REGULAR (DOUBLE) STANDARD (SINGLE) HEAVY DUTY HOLD-OPEN EDA/HEDA CUSH/HCUSH SCUSH/SHCUSH AVAILABLE NOT AVAILABLE Closer available with less tha 5.0 lbs. opeig force o 36 door. * Maximum opeig/hold-ope poit with stadard template. D = For desiger series oly. LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 35
1460T Moutig details Hige (Pull) Side Moutig 2-1/2" 64 mm 22-3/4" 578 mm 1-7/16" 37 mm 1-1/4" 32 mm 2-3/8" 60 mm 3-15/16" 100 mm 12-1/4" 311 mm Optioal 2" 51 mm 2-1/2" 64 mm No-haded Desiger Metal Cover 1460T-18 12-1/2" 318 mm 12-3/8" 314 mm 3" 76 mm Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded where a door caot swig 180 Optioal track bumper assembly assists backcheck i cushioig the opeig swig of the door. It is ot iteded to replace a auxiliary stop Reveal Should ot exceed 1/8 (3 mm) Top Rail Less tha 2-1/2 (64 mm) requires PLATE, 1460T-18 Plate requires 1-1/2 (38 mm) miimum With Full cover, use PLATE, 1460T-18FC With Desiger metal cover, use PLATE, 1460T-18DS Clearace Maximum opeig 2-3/8 (60 mm) behid door required for istallatio Templatig allows up to 180, trim ad frame permittig, limited to 115 whe optioal bumper is istalled Cosult factory if door will be held ope at 180 Hold-ope poits at 85, 90, 95, 100, 110 or 115 with hold-ope tracks Please ote that may track style door closers are capable of allowig 180 of door swig Be aware that the majority of track style closers are at their weakest closig force i the 180-130 rage Cosult factory for applicatios where a exterior or large/heavy door must swig 180 36 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1460T Moutig details Top Jamb (Pull Side) Moutig 1" 25 mm 12-1/4" 311 mm 2-3/8" 60 mm 1-1/4" 32 mm 2-1/8" 54 mm 22-3/4" 578 mm 1-1/16" 27 mm 1460T-18 Optioal No-haded Desiger Metal Cover 12-1/2" 318 mm 12-3/8" 314 mm 3" 76 mm Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded where a door caot swig 180 Track bumper assembly assists backcheck i cushioig the opeig swig of the door. It is ot iteded to replace a auxiliary stop Reveal Top Rail Should ot exceed 1/8 (3 mm) Miimum 1-1/4 (32 mm) Head Frame Less tha 2-3/4 (70 mm) requires PLATE, 1460T-18 Plate requires 1-3/4 (44 mm) miimum With full cover, use PLATE, 1460T-18FC With Desiger metal cover, use PLATE, 1460T-18DS Clearace Maximum opeig 1-1/4 (32 mm) behid door for istallatios Templatig allows up to 180, limited to 115 whe optioal bumper is istalled Cosult factory if door will be held ope at 180 Hold-ope poits at 85, 90, 95, 100, 110 or 115 with hold-ope tracks Please ote that may track style door closers are capable of allowig 180 of door swig Be aware that the majority of track style closers are at their weakest closig force i the 180 130 rage Cosult factory for applicatios where a exterior or large LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 5/16 37
1460T Moutig details Stop Face (Push Side) Moutig 2-7/8" 73 mm 22-3/4" 578 mm 2-3/8" 60 mm 1-1/4" 32 mm 7/8" 22 mm 12-1/4" 311 mm 2" 51 mm 4" 102 mm 1-1/16" 27 mm 1460T-18PA Butt Higes Should ot exceed 5 (127 mm) i width Auxiliary Stop Recommeded where a door caot swig 110 Track bumper assembly assists backcheck i cushioig the opeig swig of the door. It is ot iteded to replace a auxiliary stop Top Rail Less tha 4 (102 mm) measured from the stop face requires PLATE, 1460T-18PA. Plate requires 1-1/2 (38 mm) miimum With Full cover, use PLATE, 1460T-18PAFC With Desiger metal cover, use PLATE, 1460T-18PADS Clearace Stop Width Maximum opeig 1460T projects 2-3/8 (60 mm) from door face Miimum 1-1/4 (32 mm) Templatig allows 110, limited to 100 whe optioal bumper is istalled Variable hold-ope agles with ifiite optios 38 LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16
1460T Accessories Cyliders Arm 1460(1)T-3071 Cast Iro Cylider Assembly No-haded 1461 adjustable 1-2 1461T adjustable 2-4 Stadard 1460T-3077T Sigle Lever Stadard Arm No-haded Mouts hige side, top jamb, or stop face Track roller ot icluded with arm Covers 1460T-72 Slim Lie Plastic Cover 1460T-72FC Full Plastic Cover 1460T-72DS Desiger Metal Cover No-haded No-haded No-haded Stadard Optioal Required for platig optio ad custom powder coat fiishes Optioal Tracks 1460T-3038 Track 1460T-3038B Track with Bumper 1460T-3038H Track with Hold-Ope 1460T-3038HB Hold-Ope Track with Bumper No-haded No-haded No-haded No-haded No hold-ope No hold-ope Hold-ope Hold-ope Mouts o either side of the door Will accept hold-ope clip ad/ or bumper assembly Mouts o either side of the door Will accept hold-ope clip Mouts o either side of the door Will accept bumper assembly Mouts o either side of the door Optioal Stadard Optioal Optioal LCN Door Cotrol Catalog phoe: 877-671-7011 fax: 800-248-1460 www.allegio.com/us 009426 rev. 2/16 39