The All American Anchor is a positive drive positive setting anchor for use in all masonry materials / / /8 7 1/ /16

ALL AMERICAN ANCHORS A PIN DRIVE EXPANSION ANCHOR DIAMETER /4" 5/6" 3/8" /2" 5/8" 3/4" The All American Anchor is a positive drive positive setting anchor for use in all masonry materials. ALL AMERICAN ANCHOR (Stud Type) PULL-OUT/SHEAR TEST RESULTS 2000 PSI CONCRETE 4000 PSI CONCRETE TENSION SHEAR TENSION MIN. EMBED. MAX. EMBED. MIN. EMBED. MIN. EMBED. MAX. EMBED. (") 900 ( /2") 0 (") 600 (") 300 ( /2") 400 ( /4") 400 ( 7/8") 0 ( /4") 3000 ( /4") 2 ( 7/8") 2400 ( /2") 2200 (2 /4") 2800 ( /2") 3400 ( /2") 3200 (2 /4") 3700 (2") 3600 (3") 4200 (2") 7200 (2") 5600 (3") 5700 (2 /2") 5400 (3 3/4") 6600 (2 /2") 9200 (2 /2") 70 (3 3/4") 0,400 (3") 70 (4 /2") 9900 (3") 3,0 (3") 90 (4 /2") 3,400 All American Anchors comply with these industry standards: Meets or exceeds G.S.A. Standards G.S.A. FF-S-3, Group V, Type 2, Class 2 Meets load factors in compliance with A.N.SI. A58. Meets plating standards in compliance with A.S.T.M. B-633 Products tested in accordance with A.S.T.M. E-488.88 Tests conducted by CTI Engineering - Walnut Creek, CA 993 A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0:, or more. Anchor Size Dia. x Length /4 x 3/4 /4 x 2 3/8 5/6 x 2 3/4 5/6 x 4 3/8 x 2 3/8 3/8 x 3 /2 3/8 x 5 /2 x 2 3/4 /2 x 3 /2 /2 x 4 3/4 /2 x 6 5/8 x 4 5/8 x 6 3/4 x 5 3/4 x 6 RECOMMENDED EMBEDMENT Thread Length (In.) 5/8 3/4 /4 /8 2 7/8 /8 2 2 /2 /2 7/8 7/8 Maximum Thickness Fastened /2 7/8 /4 2 /2 5/8 3/4 3 /4 3/4 /2 2 3/4 4 /2 3 /2 2 /4 3 /4 MOST ORDERS SHIPPED UPS THAT SAME DAY! Drill Size /4 /4 5/6 5/6 3/8 3/8 3/8 /2 /2 /2 /2 5/8 5/8 3/4 3/4 Anchor Diameter /4" 5/6" 3/8" /2" 5/8" 3/4" A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC. The All American Anchor is an impact-expansion type concrete anchor. No special tools are required. The only tools needed are a drill (to bore the hole) and a hammer (to set the anchor). The body of the anchor is carbon steel and the drive pin is hardened steel. The entire anchor is yellow dicromate over zinc plating. Sizes available are listed below. SIZES AVAILABLE RECOMMENDED SPACING Embedment " 3/4" /8" 2 /8" /4" 2 /2" /2" 3" 3/4" 3 /4" 2" 3 /2" Item Number 434AS 4238AS 56200AS 56234AS 56400AS 38238AS 3832AS 380AS 2234AS 232AS 2434AS 2600AS 58400AS 58434AS 58600AS 340AS 34600AS Box Qty. 30 30 20 20 Minimum Spacing between Anchors 3 /2 3 /2 3 /2 4 4 3/8 5 5 /4 6 6 /8 7 /2 7 9 Size /4 x 3/4 /4 x 2 3/8 5/6 x 2 5/6 x 2 3/4 5/6 x 4 3/8 x 2 3/8 3/8 x 3 /2 3/8 x 5 /2 x 2 3/4 /2 x 3 /2 /2 x 4 3/4 /2 x 6 5/8 x 4 5/8 x 4 3/4 5/8 x 6 3/4 x 5 3/4 x 6 Minimum Edge Distance 3/4 3/4 3/4 2 2 3/6 2 /2 2 5/8 3 3 /6 3 3/4 3 /2 4 /2 Anchor spacing recommendations serve only as a guideline. Spacing will vary as the density of the masonry material changes. CHARLES CITY, IOWA 800-833-647 Fax 64-228-624 www.dfsusa.com

STUD-TYPE ALL AMERICAN ANCHORS A PIN-DRIVE EXPANSION ANCHOR EASY TO USE: Drill hole same size as anchor diameter Insert anchor with nut and washer attached Hammer pin until flush VISUALLY INSPECTABLE AFTER SET CARBON STEEL BODY WITH HARDENED SETTING PIN HIGH PULL-OUT & SHEAR STRENGTH ZINC & DICHROMATE PLATED NUTS & WASHERS INCLUDED AVAILABLE IN STAINLESS STEEL (BULK ONLY) ALL AMERICAN ANCHORS ARE PACKAGED IN: Count Open Stock Boxes Bulk Packaging WHAT ADVANTAGES ARE THERE?. The nut and washer can be preset for your desired embedment... Choose flush at the top or screw to the bottom for stud-type applications. Flush Stud 2. The All American Anchor is Not Set visually inspectable after set. When the pin is hammered down to meet the threads, the anchor is fully set. NO GUESSWORK or torque necessary like a Wedge Anchor or Sleeve Anchor. INSTALLATION PROCEDURE.. 2. 3. 4. WHERE DO I USE All American Anchors? Outlet Boxes Stadium Seats Steel & Wood Plates Machine Anchoring Water & Gas Meters Mail Boxes Cash Machines Conveyor Belt Mounts Bracing Shelving Hand & Guard Rails Grain & Storage Bins Light Fixtures Steel Buildings. Drill hole of sufficient depth using same diameter DFS Bit as anchor being installed. 2. Turn nut on anchor as required. May be flush with top or turned on fully to provide stud finish. 3. With nut, washer, and set-pin in place, insert anchor into hole. 4. Using a proper sized hammer, set pin with several sharp and square strikes on head of pin until pin is flush with top of anchor. Anchor is now properly set. 5. No need to torque nut to set anchor. WARNING: Wear eye protection. ALL AMERICAN ANCHOR SETTING TOOLS The All American Anchor Setting Tools were designed for setting anchors in areas where a solid blow to the anchor pin is not possible, (such as deep electrical boxes). This hardened steel tool is zinc and yellow dichromate plated. Item Number Box Qty. Size 4560ST 3820ST 58340ST /4" to 5/6" 3/8" to /2" 5/8" to 3/4" For setting pin drive anchors in areas where a solid blow to the pin head is not possible. Meets plating standards in compliance with A.S.T.M. b-633. Copyright 200, Diversified Fastening Systems, Inc.

DFS SECURITY ANCHORS THE ONLY "REVERSIBLE HEAD" SECURITY ANCHOR ROUND HEAD FLAT HEAD The DFS Security Anchor is tamper and vibration resistant and works in all poured concrete and brick materials. DIAMETER /4" 5/6" 3/8" /2" 5/8" 3/4" PULL-OUT/SHEAR TEST RESULTS MIN. EMBED. (") 900 ( /4") 400 ( /2") 2200 (2") 3600 (2 /2") 5400 (3") 70 TENSION 2000 PSI CONCRETE MAX. EMBED. ( /2") 0 ( 7/8") 0 (2 /4") 2800 (3") 4200 (3 3/4") 6600 (4 /2") 9900 SHEAR 4000 PSI CONCRETE TENSION MIN. EMBED. MIN. EMBED. MAX. EMBED. (") 600 ( /4") 3000 ( /2") 3400 (2") 7200 (2 /2") 9200 (3") 3,0 (") 300 ( /4") 2 ( /2") 3200 (2") 5600 (2 /2") 70 (3") 90 ( /2") 400 ( 7/8") 2400 (2 /4") 3700 (3") 5700 (3 3/4") 0,400 (4 /2") 3,400 DFS Security Anchors comply with these industry standards: Meets I.C.B.O. standards REF: Report #494 Meets City of Los Angeles Approval REF: 09 Meets or exceeds G.S.A. Standards G.S.A. FF-S-3, Group V, Type 2, Class 2 Meets load factors in compliance with A.N.SI. A58. Meets plating standards in compliance with A.S.T.M. B-633 Products tested in accordance with A.S.T.M. E-488.88 Tests conducted by CTI Engineering - Walnut Creek, CA 993 A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0:, or more. Item Number 434FS 4238FS 56234FS 56400FS 38238FS 3832FS 380FS 2234FS 232FS 2434FS 2600FS 58400FS 58600FS 340FS 34600FS SIZES AVAILABLE Box Qty. 30 30 20 20 Description /4 x 3/4 /4 x 2 3/8 5/6 x 2 3/4 5/6 x 4 3/8 x 2 3/8 3/8 x 3 /2 3/8 x 5 /2 x 2 3/4 /2 x 3 /2 /2 x 4 3/4 /2 x 6 5/8 x 4 5/8 x 6 3/4 x 5 3/4 x 6 CARBON STEEL WITH HEAT TREATED SETTING PIN Anchor Size Dia. x Length /4 x 3/4 /4 x 2 3/8 5/6 x 2 3/4 5/6 x 4 3/8 x 2 3/8 3/8 x 3 /2 3/8 x 5 /2 x 2 3/4 /2 x 3 /2 /2 x 4 3/4 /2 x 6 5/8 x 4 5/8 x 6 3/4 x 5 3/4 x 6 Thread Length (In.) 5/8 3/4 /4 /8 2 /8 2 2 5/8 2 2 2 Maximum Thickness Fastened /2 7/8 /4 2 /2 5/8 3/4 3 /4 3/4 /2 2 3/4 4 /2 3 /2 2 /4 3 /4 *Min. Embedment /4 /4 /2 /2 /2 2 2 2 2 2 /2 2 /2 3 3 Drill Size /4 /4 5/6 5/6 3/8 3/8 3/8 /2 /2 /2 /2 5/8 5/8 3/4 3/4 MOST ORDERS SHIPPED UPS THAT SAME DAY! CHARLES CITY, IOWA 800-833-647 Fax 64-228-624

FLAT HEAD ROUND HEAD DFS SECURITY ANCHORS THE ONLY "REVERSIBLE HEAD" SECURITY ANCHOR TAMPER RESISTANT AND VIBRATION RESISTANT REVERSIBLE NUT FOR ROUND OR FLAT HEAD STYLES CARBON STEEL ANCHOR BODY AND NUT WITH HARDENED SETTING PIN WHAT ADVANTAGES ARE THERE? Unlike other security type anchors...no special tools and no welding are required to secure anchor. A hammer is all you need. Only one anchor to be inventoried for round head and flat head applications. HIGH PULL-OUT AND SHEAR STRENGTH SECURITY NUTS ARE INCLUDED AVAILABLE IN OPEN STOCK BOXES OR BULK INSTALLATION PROCEDURE. 2. 3. 4. Flat Round Head Head. 2. 3. 4. Drill hole of sufficient depth using same diameter DFS Drill Bit as anchor being installed. Select head style (round/flat)...then turn Security Nut flush with the top of anchor. Insert anchor into predrilled hole. Drive in Set Pin with hammer until flush. Use 2-3 lb. hammer for small anchors and 4-5 lb. hammer for medium and large anchors. Slotted anchor base expands into concrete. Anchor is set! WHERE DO I USE DFS SECURITY ANCHORS? Prison Furniture Burglar Bars Security Door Frames Motion Detectors Fencing Lock Boxes Money Meters Vending Machines Benchs Light Fixtures Playground Equipment Thresholds Stadium Seating Cash Machines Mail Boxes Door Frames Copyright 2005, DFS/USA, Diversified Fastening Systems, Inc.

DFS WEDGE ANCHORS FOR HEAVY-DUTY ANCHORING TO POURED CONCRETE & BRICK The DFS Wedge Anchor has a carbon steel anchor body and clip which ensures proper anchoring in all masonry materials. CARBON STEEL AND 303 STAINLESS STEEL SIZES Carbon Steel Item Number() Box Qty. Size 434WS 424WS 434WS 5628WS 56234WS 56300WS 56400WS 3824WS 38234WS 38300WS 3832WS 38334WS 380WS 38700WS 2234WS 2334WS 244WS 2WS 2700WS 282WS 2WS 220WS 5832WS 5842WS 580WS 58600WS 58700WS 5882WS 58WS 5820WS 3444WS 34434WS 3452WS 3464WS 34700WS 3482WS 34WS 3420WS 78600WS 78800WS 78WS 6000WS 9000WS 200WS 20 20 20 0 0 0 0 0 5 5 5 5 5 5 /4 x 3/4 /4 x 2 /4 /4 x 3 /4 *5/6 x 2 /8 *5/6 x 2 3/4 *5/6 x 3 *5/6 x 4 3/8 x 2 /4 3/8 x 2 3/4 3/8 x 3 3/8 x 3 /2 3/8 x 3 3/4 3/8 x 5 3/8 x 7 /2 x 2 3/4 /2 x 3 3/4 /2 x 4 /4 /2 x 5 /2 /2 x 7 /2 x 8 /2 /2 x 0 /2 x 2 5/8 x 3 /2 5/8 x 4 /2 5/8 x 5 5/8 x 6 5/8 x 7 5/8 x 8 /2 5/8 x 0 5/8 x 2 3/4 x 4 /4 3/4 x 4 3/4 3/4 x 5 /2 3/4 x 6 /4 3/4 x 7 3/4 x 8 /2 3/4 x 0 3/4 x 2 *7/8 x 6 *7/8 x 8 *7/8 x 0 * x 6 * x 9 * x 2 () - FOR STAINLESS CHANGE ITEM # LETTERS TO SW * - CALL FOR SPECIAL QUOTE ON STAINLESS MINIMUMS REQUIRED MOST ORDERS SHIPPED THAT SAME DAY! (36 Available on Request) TEST RESULTS FOR DFS WEDGE ANCHOR DIAMETER /4" 5/6" 3/8" /2" 5/8" 3/4" 7/8" " 2000 PSI CONCRETE 4000 PSI CONCRETE TENSION SHEAR TENSION MIN. EMBED. MAX. EMBED. MIN. EMBED. MIN. EMBED. MAX. EMBED. (") 900 ( /2") 0 (") 900 (") 0 ( /2") 2000 ( /4") 400 ( 7/8") 0 ( /4") 2700 ( /4") 900 ( 7/8") 3700 ( /2") 2200 (2 /4") 2800 ( /2") 4 ( /2") 3600 (2 /4") 4800 (2") 3600 (3") 4200 (2") 6400 (2") 4800 (3") 8200 (2 /2") 5400 (3 3/4") 6600 (2 /2") 9400 (2 /2") 60 (3 3/4") 9700 (3") 70 (4 /2") 9900 (3") 4,800 (3") 7200 (4 /2") 3,700 (3 /2"),300 (5 /4") 3,700 (3 /2") 2,0 (3 /2") 2,800 (5 /4") 6,300 (4") 9800 (6") 5,800 (4") 27,300 (4") 3,700 (6") 2,000 DFS Wedge Anchors comply with these industry standards: Meets I.C.B.O. standards REF: Report #494 Meets load factors in compliance with A.N.S.I. A58. Meets or exceeds G.S.A. Standards G.S.A. FF-S-3, Meets plating standards in compliance with A.S.T.M. B-633 Group II, Type 4, Class Products tested in accordance with A.S.T.M. E-488.88 Tests conducted by CTI Engineering - Walnut Creek, CA 993 A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0:, or more. A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC. CHARLES CITY, IOWA 800-833-647 Fax 64-228-624

DFS WEDGE ANCHORS FOR HEAVY-DUTY ANCHORING TO POURED CONCRETE & BRICK A STANDARD WEDGE-TYPE ANCHOR FOR POURED CONCRETE & BRICK CARBON STEEL ANCHOR BODY AND CLIP (ALSO AVAILABLE IN STAINLESS STEEL.) DRILL SAME HOLE DIAMETER AS THE ANCHOR DIAMETER EXTRA THREADS FOR LOCKING NUTS OR SHIMS ZINC PLATED ANCHOR BODY, CLIP, NUTS AND WASHERS AVAILABLE IN OPEN STOCK BOXES OR BULK CONFORMS TO THE FOLLOWING LISTINGS/APPROVALS: Meets I.C.B.O. standards REF: Report #494 Meets G.S.A. Standards G.S.A. FF-S-3, Group II, Type 4 Meets load factors in compliance with A.N.S.I. A58. Meets plating standards in compliance with A.S.T.M. B-633 Products tested in accordance with A.S.T.M. E-488.88 WHAT ADVANTAGES ARE THERE? DFS WEDGE ANCHORS can be used in deep electrical boxes where a solid hammer blow to the head of a pin-drive anchor is not possible. DFS WEDGE ANCHORS can be used near the edge of poured concrete floors and steps with a reduced risk of cracking or "blowing out" the concrete. INSTALLATION PROCEDURE. 2. 3. Drill hole deeper than embedment using an ANSI approved drill bit. Same diameter as the anchor diameter. Tap anchor into hole with nut and washer attached. Tighten nut 3-5 turns until anchor wedges securely. WHERE DO I USE DFS WEDGE ANCHORS? Steel & Wood Plates Outlet Boxes Mail Boxes Guard Rails Grain & Storage Bins Steel Buildings Shelving & Bracing Stadium Seating Sign Bases Hand Rails Light Fixtures Machine Anchoring Water & Gas Meters Storage Tanks Pipe Hanger Mounts Phone Booths Headers Dock Bumpers Equipment Racks Conveyor Belt Mounts Manhole Applications Copyright 2009, DFS/USA, Diversified Fastening Systems, Inc.

SLEEVE ANCHORS For Heavy Duty Anchoring To Poured Concrete, Block & Brick STUD HEAD FLAT HEAD Designed for applications which require high pull-out values at a reasonable cost. Easy to install.. DFS SLEEVE ANCHORS -Stud Head TEST DATA 2. 3. ITEM NUMBER 438SL 424SL 562SL 5622SL 3878SL 38300SL 38400SL 224SL 2300SL 2400SL 2600SL 5824SL 58300SL 5842SL 58458SL 58600SL 3422SL 3444SL 3464SL 4200SL 4300SL 4400SL 38234SL 3840SL 380SL 38600SL DIAMETER x TOTAL LENGTH /4 x 3/8" /4 x 2 /4" 5/6 x /2" 5/6 x 2 /2" 3/8 x 7/8" 3/8 x 3" 3/8 x 4" /2 x 2 /4" /2 x 3" /2 x 4" /2 x 6" 5/8 x 2 /4" 5/8 x 3" 5/8 x 4 /2" 5/8 x 4 5/8" 5/8 x 6" 3/4 x 2 /2" 3/4 x 4 /4" 3/4 x 6 /4" DFS SLEEVE ANCHORS - Flat Head /4 x 2" /4 x 3" /4 x 4" 3/8 x 2 3/4" 3/8 x 4" 3/8 x 5" 3/8 x 6" BOX QTY 0 0 0 0 5 5 MIN. EMB. " " " " /4" /4" /4" /2" /2" /2" 3" 2" 2" 3 /2" 3 /2" 3 /2" 2" 3 /2" 3 /2" " /4" /4" /4" /4" 2 /2" 3" PULL-OUT 300 300 700 700 2400 2400 2400 4700 4700 4700 4700 5900 5900 5900 5900 5900 9200 9200 9200 300 300 300 2400 2400 2400 2400 SHEAR 0 0 2000 2000 3000 3000 3000 5200 5200 5200 5200 0 0 0 0 0 00 00 00 0 0 0 3000 3000 3000 3000 Meets or exceeds U.S. Government G.S.A. Specification FF-S-3, Group II, Type 3, Class 3 All tests were conducted in 30 psi concrete. A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0: or more. MOST ORDERS SHIPPED UPS THAT SAME DAY! A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC. CHARLES CITY, IOWA 800-833-647 Fax 64-228-624

STUD HEAD FLAT HEAD SLEEVE ANCHORS For Heavy-Duty Anchoring To Poured Concrete, Block & Brick FOR USE IN ALL MASONRY MEDIA HIGH PULL-OUT STRENGTH CAN BE USED IN A BOTTOMLESS HOLE 2 VARIETIES OF HEAD STYLES AVAILABLE IN OPEN STOCK BOXES OR BULK. INSTALLATION PROCEDURE WHAT ADVANTAGES ARE THERE? Sleeve Anchors can be used near the edge of poured concrete floors and steps with a reduced risk of cracking or "blowing out" the concrete. No oversize hole is required for sleeve anchors. Drill the same hole diameter as the anchor diameter. Flush mount anchoring can be achieved with "Flat Head" style sleeve anchors.. 2. 3. Drill hole deeper than the embedment using an A.N.S.I. approved drill bit same diameter as the anchors diameter. Tap anchor into hole with nut and washer attached. Tighten nut 3-5 turns until the anchor wedges securely. WHERE DO I USE SLEEVE ANCHORS? Steel & Wood Plated Outlet Boxes Mail Boxes Guard Rails Grain & Storage Bins Steel Buildings Shelving & Bracing Stadium Seating Sign Bases Hand Rails Light Fixtures Machine Anchoring Water & Gas Meters Storage Tanks Pipe Hanger Mounts Phone Booths Headers Dock Bumpers Equipment Racks Conveyor Belt Mounts Manhole Applications Copyright 2004, DFS/USA, Diversified Fastening Systems, Inc.

DFS DROP-IN ANCHORS FOR FLUSH AND SHALLOW EMBEDMENT ANCHORING The DFS Drop-In Anchors were designed as a replacement for lead anchors and lag shields for more satisfactory anchoring of objects to concrete and brick. DFS DROP-IN ANCHORS - USS USS Coarse Thread (Available in Richmond Thread) Carbon Steel Anchor Body Carbon Steel Setting Plug Zinc Plated Anchor Diameter /4" 5/6" 3/8" /2" 5/8" 3/4" DFS Drop-In Anchors comply with these industry standards: Meets G.S.A. Standards G.S.A. FF-2-3, Group III, Type Meets load factors in compliance with A.N.S.I. A58. Meets plating standards in compliance with A.S.T.M. B-633 Products tested in accordance with A.S.T.M. E-488.88 A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0: or more. RECOMMENDED SPACING Embedment " 3/8" /2" 2" 2 /2" 3 /8" Spacing Between Anchors 3 /2 4 /8 5 /6 7 8 5/6 0 /2 Minimum Edge Distance 3/4 2 /6 2 3/6 3 /2 4 /8 5 /4 Anchor spacing recommendations serve only as a guideline. Spacing will vary as the density of the masonry material changes. Anchor Size /4" 5/6" 3/8" /2" 5/8" 3/4" Outside Diameter 3/8" 3/8" /2" 5/8" 7/8" " Overall Length " 3/8" /2" 2" 2 /2" 3 /8 Thread Length 3/8" 9/6" 5/8" 3/4" " /4" Min. Embedment " 3/8" /2" 2" 2 /2" 3 /8" Drill Size 3/8" 3/8" /2" 5/8" 7/8" " *Pull Out 2273 3224 5520 770 200 Box Qty. pcs. 5 *Concrete used for testing was 3000PSI. These values cannot be guaranteed due to variations in concrete. Anchors should be tested in specific material. A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0:, or more. DFS DROP-IN ANCHOR TOOL for setting DFS Drop-In Anchors Item Number DST4S DST565 DST38S DST2S DST58S DTS34S Item Number 4DS 5636DS 3896DS 2200DS 58238DS 34300DS Box Qty. Box Qty. Size /4" 5/6" 3/8" /2" 5/8" 3/4" Description /4" 5/6" 3/8" /2" 5/8" 3/4" ASK FOR MADE IN USA DROP-IN ANCHORS CHARLES CITY, IOWA 800-833-647 Fax 64-228-624 www.dfsusa.com A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC.

DFS DROP-IN ANCHORS FOR FLUSH AND SHALLOW EMBEDMENT ANCHORING FOR FLUSH & SHALLOW EMBEDMENT ANCHORING TO POURED CONCRETE AND BRICK MATERIALS FOR USE WITH ANY LENGTH USS COARSE BOLT OR THREADED ROD CARBON STEEL BODY AND SETTING PLUG ALSO AVAILABLE WITH RICHMOND THREAD FOR REBAR REINFORCEMENT ZINC PLATED FOR CORROSION RESISTANCE WHAT ADVANTAGES ARE THERE? DFS Drop-In Anchors have a much smaller hole diameter requirement than lead anchors. The DFS Drop-In Anchors have much greater pull-out strength than lead anchors and lag shields.. 2. DFS Drop-In Anchors are preassembled. Ready for use right out of the box!. 2. Drill Hole (same drill depth as anchor INSTALLATION PROCEDURE 3. 4. Insert AVAILABLE WITH OR WITHOUT DROP-IN SETTING TOOLS AVAILABLE IN OPEN STOCK BOXES OR BULK Drill Hole (same drill depth as anchor length.) Insert anchor. Set anchor with setting tool. Drop-In Anchor is set and ready to accept any length bolt or threaded rod. 3. 4. Set anchor with Drop-In Anchor is set and ready to accept any length bolt or WHERE DO I USE DFS DROP-IN ANCHORS? Temporary Machinery Anchoring Overhead Hangers with Threaded Rod Railings, Guard Rails and Hand Rails Shelving and Brackets Anchoring Rack Systems Lighting Fixtures Gates and Fencing 4 x 4 Wood Anchoring Rebar to Old, Existing Masonry Floors Other Shallow or Flush Embedment Anchoring Copyright 200, DFS/USA, Diversified Fastening Systems, Inc.

LIBERTY ANCHORS FOR MEDIUM TO HEAVY-DUTY ANCHORING TO ALL CONCRETE BLOCK WALLS The DFS Liberty Anchor was designed for anchoring and through-bolting into hollow walls, ceilings and other blind space applications. LIBERTY ANCHOR - MALE VERSION (External Thread) (solid body) PATENTED ITEM NUMBER DIAMETER x TOTAL LENGTH THREAD LENGTH 38600TM 3/8" x 6" 4" BOX QTY Male Version Solid Anchor Body (Drill Same Hole Diameter as Anchor Diameter) TEST PERFORMANCE DATA LIBERTY MALE PULL OUT 3/8" x 6 800 lbs. SHEAR 3000 lbs. Liberty Anchors comply with these industry standards: Meets G.S.A. Standards G.S.A. FF-B-588C Meets load factors in compliance with A.N.S.I. A58. Meets plating standards in compliance with A.S.T.M. B-633 Products tested in accordance with A.S.T.M. E-488.88 A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0: or more. LIBERTY ANCHOR - FEMALE VERSION (Internal Thread) PATENTED (WILL WORK WITH ANY LENGTH THREADED ROD) ITEM NUMBER DIAMETER DRILL SIZE BOX QTY MINIMUM GRIP RANGE 38000TF 3/8" /2" /2" 2000TF /2" 5/8" 5/8" Female Version USS Internally Threaded TEST PERFORMANCE DATA LIBERTY FEMALE PULL OUT 3/8" 3200 lbs. /2' 5800 lbs. SHEAR * * Liberty Anchors comply with these industry standards: Meets G.S.A. Standards G.S.A. FF-B-588C Meets load factors in compliance with A.N.S.I. A58. Meets plating standards in compliance with A.S.T.M. B-633 Products tested in accordance with A.S.T.M. E-488.88 A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0: or more. MOST ORDERS SHIPPED THAT SAME DAY! A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC. CHARLES CITY, IOWA 800-833-647 Fax 64-228-624

LIBERTY ANCHORS FOR MEDIUM TO HEAVY-DUTY ANCHORING TO ALL CONCRETE BLOCK WALLS USS COURSE THREADED GRAVITY-ACTIVATED TOGGLE HEAD DRILL SAME HOLE DIAMETER AS DIAMETER LIBERTY MALE ZINC & DICHROMATE PLATED FOR CORROSION RESISTANCE NUTS AND WASHERS INCLUDED LIBERTY FEMALE WHAT ADVANTAGES ARE THERE? Libertys are much stronger than toggle bolts and may also be removed when necessary. Liberty female allows you to produce a thru-bolt anchor up to 2 feet long! INSTALLATION PROCEDURE. DRILL HOLE PROPER SIZE THROUGH OBJECT BEING FASTENED AND THROUGH WALL, CEILING, ETC. 2. INSERT WITH NUT AND WASHER ATTACHED TO ANCHOR, THROUGH ALL MATERIAL. (Anchor can be used inside "blind" hollow walls, ceilings, etc.) 3. TURN ROD 80 DEGREES, GRAVITY ACTIVATED RETAINING BAR WILL TURN SECURING THE ANCHOR. INTERNALLY THREADED USS COARSE WILL ACCEPT ANY LENGTH THREADED ROD GRAVITY ACCUATED TOGGLE HEAD FOR " THRU-BOLTING" HEAVY OBJECTS TO CONCRETE BLOCK WALLS ZINC & DICHROMATE PLATED FOR CORROSION RESISTANCE WHERE DO I USE LIBERTY ANCHORS? Anchoring to Crawl Spaces Railings to Block Walls Thru-Bolting Applications Heavy Racks & Shelving to Block Walls Deck Headers Through Block Walls Pipe Hangers Anchoring to Steel Beams INSTALLATION PROCEDURE DRILL HOLE PROPER SIZE THROUGH OBJECT BEING FASTENED AND THROUGH WALL, CEILING, ETC. INSERT WITH THREADED ROD ATTACHED TO ANCHOR, THROUGH ALL MATERIALS. (Anchor can be used inside "blind" hollow walls, ceilings, etc.) TURN ROD 80 DEGREES, GRAVITY ACTIVATED RETAINING BAR WILL TURN SECURING THE ANCHOR. SIMPLY TIGHTEN THE NUT TO FASTEN OBJECT. (The retaining bar turns only one direction, so turning the rod back to it's original position will allow you to remove the anchors.) Copyright 200, DFS/USA, Diversified Fastening Systems

T-ANCHORS LIGHT DUTY ANCHORING TO HOLLOW WALLS & CEILINGS The DFS T-Anchor has a gravity activated toggle head for use in hollow walls and ceilings. Can be used in concrete, steel and wood. FOR LIGHT TO MEDIUM DUTY FASTENING TO HOLLOW WALLS AND CEILINGS T-ANCHORS. 2. Item Number 434TS 422TS 434TS 5622TS 5634TS 56334TS 3834TS 38334TS 38400TS 3842TS Diameter x Total Length /4" x 3/4" /4" x 2 /2" /4" x 3 /4" 5/6" x 2 /2" 5/6" x 3 /4" 5/6" x 3 3/4" 3/8" x 3 /4" 3/8" x 3 3/4" 3/8" X 4" 3/8 x 4 /2" Grip Range " " - 3/4" " - 2 /2" 7/8" - /2" /4" - 2 /4" 7/8" - 2 3/4" " - 2" 7/8" - 2 /2" 2" - 2 3/4" /8" - 3 /8" Drill Size 5/6 5/6 5/6 5/6 5/6 5/6 3/8 3/8 3/8 3/8 Box Qty. Drill hole proper diameter. 3. 4. Insert Anchor with nut and washer attached. TEST PERFORMANCE DATA DIAMETER PULL OUT /4" (all lengths) 700 lbs. 5/6" (all lengths) 900 lbs. 3/8" (all lengths) 0 lbs. SHEAR 0 lbs. 2300 lbs. 3000 lbs. Gravity turns retaining bar. Tighten nut until anchor is set. T-Anchors comply with these industry standards: Meets or exceeds G.S.A. Standards G.S.A. FF-B-588C Meets load factors in compliance with A.N.S.I. A58. Meets plating standards in compliance with A.S.T.M. B-633 Products tested in accordance with A.S.T.M. E-488.88 A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0: or more. MOST ORDERS SHIPPED THAT SAME DAY! A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC. CHARLES CITY, IOWA 800-833-647 Fax 64-228-624

T-ANCHORS LIGHT DUTY ANCHORING TO HOLLOW WALLS & CEILINGS DFS T-ANCHORS SMALLER HOLE REQUIREMENTS THAN TOGGLE BOLTS MAY BE USED IN HOLLOW BLOCK WALLS AND CEILINGS ONE SIZE HOLE TO DRILL... NO REALIGNING OF HOLES IS NECESSARY ZINC & DICHROMATE PLATED FOR CORROSION RESISTANCE NUTS & WASHERS INCLUDED AVAILABLE IN OPEN STOCK BOXES OR BULK WHAT ADVANTAGES ARE THERE? A 5/6" toggle bolt requires a 7/8" hole. The T-Anchor with a 5/6" diameter requires a 5/6" hole. Same drill bit diameter as anchor diameter. T-Anchors can be used in concrete block, wood, steel or and any hollow space application. WHERE DO I USE T-ANCHORS? Signs & Awnings Railings & Guard Rails Overhead Doors Light Fixtures Electrical Boxes Shelving Brackets Cable TV Units Any Hollow Wall or Ceiling Application! Copyright 200, DFS/USA, Diversified Fastening Systems

CON-SERT SCREWS A SELF TAPPING CONCRETE SCREW FLAT HEAD PHILLIPS Con-Sert Screws were designed to achieve higher pull-out values at shallower embedments than competitive masonry screws. The Con-Sert concrete screws replace plastic anchors and sheet metal screws for lightweight anchoring. Con-Sert Screws eliminate the need for two piece anchoring. The Con-Sert Screw will cut threads in a pre-drilled hole in precast, concrete, block, poured concrete, brick or any other masonry material. Con-Sert screws are made of heat treated carbon steel with zinc and yellow dichromate plating. #8 TEST PERFORMANCE DATA 2000 PSI CONCRETE 4000 PSI CONCRETE TENSION SHEAR TENSION MIN. EMBED. MAX. EMBED. MIN. EMBED. MIN. EMBED. MAX. EMBED. (/2") 2 (3/4") 3 (/2") 6 (/2") 0 (3/4") 6 /2" recommended embedment. Up to 3/4" embedment only in extremely soft masonry. Tests conducted by CTI Engineering - Walnut Creek, CA A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations) may require a safety factor of as much as 0:, or more. Results were based upon drilling the pilot hole with a close tolerance DFS/USA consert drill bit. To determine screw length needed, add 3/4" to the thickness of the material being fastened. *Recommended embedment Screw Diameter #8 /4" SLOTTED HEX HEAD (Point to Point) /4" DIAMETER TEST PERFORMANCE DATA 2000 PSI CONCRETE 4000 PSI CONCRETE TENSION SHEAR TENSION MIN. EMBED. MAX. EMBED. MIN. EMBED. MIN. EMBED. MAX. EMBED. (3/4") 700 ( /4") 0 (3/4") 800 (3/4") 0 ( /4") 6 3/4" recommended embedment. Up to /4" embedment only in extremely soft masonry. Tests conducted by CTI Engineering - Walnut Creek, CA A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations) may require a safety factor of as much as 0:, or more. Results were based upon drilling the pilot hole with a close tolerance DFS/USA consert drill bit. To determine screw length needed, add 3/4" to the thickness of the material being fastened. *Recommended embedment RECOMMENDED SPACING Spacing between screws center to center 3/4" 2 5/8" Minimum Edged Distance 7/8" 5/6" Anchor spacing recommendations serve only as a guideline. Spacing will vary as the density of the masonry material changes. CON-SERT (GOLD SCREWS) SCREWS /4" (3/4" Embedment) Hex Head Item Number 4034HS 4HS 44HS 42HS 4200HS 424HS 422HS 4300HS 432HS 4400HS 442HS Masonry Drill Bit included in each box of screws. All screws have dicromate over zinc plating (3/4" recommended embedment). CON-SERT (GOLD SCREWS) SCREWS #8 (/2" Embedment) Hex Head Item Number 0802HS 08034HS 08HS 084HS 082HS 08200HS Flat Head Phillips Item Number 4034PS 4PS 44PS 42PS 4200PS 424PS 422PS 4300PS 432PS 4400PS 442PS Flat Head Phillips Item Number 08034PS 08PS 084PS 082PS Box Qty. Box Qty. Recommended Embedment Size 3/4" /4 x 3/4 3/4" /4 x 3/4" /4 x /4 3/4" /4 x /2 3/4" /4 x 2 3/4" /4 x 2 /4 3/4" /4 x 2 /2 3/4" /4 x 3 3/4" /4 x 3 /2 3/4" /4 x 4 3/4" /4 x 4 /2 Recommended Embedment /2" /2" /2" /2" /2" /2" Size 8 x /2 8 x 3/4 8 x 8 x /4 8 x /2 8 x 2 Masonry Drill Bit included in each box of screws. All screws have yellow dicromate over zinc plating (/2" recommended embedment). MOST ORDERS SHIPPED THAT SAME DAY! A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC. CHARLES CITY, IOWA 800-833-647 Fax 64-228-624 www.dfsusa.com

SLOTTED HEX HEAD (Point to Point) FLAT HEAD PHILLIPS SCREWS CON-SERT A SELF TAPPING CONCRETE SCREW WILL ELIMINATE AND REPLACE PLASTIC PLUGS & LEAD ANCHORS WILL "TAP THRU" LIGHT STEEL, PLASTIC, WOOD INTO POURED CONCRETE, PRECAST, BLOCK AND BRICK MATERIALS ALL CON-SERTS ARE CASE HARDENED WITH ZINC & DICROMATE PLATING CON-SERTS ARE COMPLETELY REUSABLE CON-SERTS HAVE A SHARP "GIMLET" POINT FOR EASY STARTING CON-SERTS ARE AVAILABLE IN: 5/6" Slotted Hex Head - /4" Diameter #3 Flat Head Phillips - /4" Diameter /4" Slotted Hex Head - #8 Diameter #2 Flat Head Phillips - #8 Diameter CON-SERTS ARE PACKAGED IN: Count Open Stock Box with Bit Bulk with/without Bits CON-SERT /4" (3/4" Embedment) WHY ONLY A 3/4" EMBEDMENT? Con-Serts have a uniquely engineered thread design and drill bit diameter which allows maximum pullout at minimum embedment. HOW DOES CON-SERT SAVE MONEY? HERE'S HOW: In one ( ct.) box of Con-Sert Screws drilling at 3/4" embedment you would drill a total of 6'3" of concrete. Other masonry screws require a /4" minimum embedment...and the same screws would have you drilling 0'5" of concrete! That's over 4' of extra drilling plus extra time, extra money and extra bits. A 0 box job would have you drilling over 40 feet of extra concrete! WHERE DO I USE CON-SERTS? FOR ANCHORING: Conduit Straps Partitions Joist Hangers Pipe Run supports Duct Straps Gutters Fuse Boxes Lighting Fixtures CON-SERT #8 (/2" Embedment) Firring Strips 2x2 & 4x4 Wood Door Frames Wall Hangings Light Handles & Rails Curtain Rods Electrical Boxes Window Channels Carpet Strips Threshold Plates 3/4" /2" Drill hole with Con-Sert I Bit through object and into concrete. Use Con-Sert I Tool or (5/6" Hex Driver or #3 Phillips Driver) to embed screws. (REMEMBER: Thickness of object + 3/4" = length of screw) Drill hole with Con-Sert #8 Bit or /8" Masonry Bit through object and into concrete. Use Con-Sert #8 Tool or (/4" Hex Driver or #2 Phillips Driver) to set screw. (REMEMBER: Thickness of object + /2" = length of screw) Copyright 200, Diversified Fastening Systems, Inc.

CON-SERT TOOLS FOR DRILLING AND DRIVING CON-SERT SCREWS Con-Sert Tools are a unique "one piece" drill and driver with adjustable depth settings for fast and easy installation of Con-Sert screws. CON-SERT TOOLS Fits Any 3/8" and Larger Jacobs Chuck Drill ONE MAN - ONE TOOL DRILL & DRIVER UNIQUE SELF RETRACTING CARBIDE DRILL BIT ADJUSTABLE DRILL DEPTH SETTINGS Patent # 4,954,0 CON-SERT I TOOL REPLACEABLE HEX END HARDENED PHILLIPS DRIVER INCLUDED HEAVY DUTY STORAGE TUBE INCLUDED CON-SERT TOOLS & ACCESSORIES /4" (FOR GOLD SCREWS) Item Number CSTS CHES CST0S CSB42S CPA003S CSB62S Box Qty. Description Con-Sert Tool I w/phillips adapter and sleeve (For Screws up to 2 /2" long) Pack ConSert I Hex End Pack ConSert I Tool Sleeve only Pack ConSert Drill Bit 4 /2" long (For Screws 2 /2" or less) Pack ConSert #3 Phillips Adaptor Pack ConSert Drill Bit 6 /2" long (For Screws up to 4 /2" long) CON-SERT #8 TOOL CON-SERT TOOLS & ACCESSORIES #8 (FOR GOLD SCREWS) Item Number CST8S Box Qty. Description Con-Sert Tool #8 w/sleeve (screws up to /2" long) ONE MAN - ONE TOOL DRILL & DRIVER UNIQUE SELF RETRACTING CARBIDE DRILL BIT ADJUSTABLE DRILL DEPTH SETTINGS REPLACEABLE HEX END HARDENED PHILLIPS DRIVER INCLUDED HEAVY DUTY STORAGE TUBE INCLUDED CSB08S CPA002S Con-Sert Bit 4 /2" long (for #8 screws) Con-Sert #2 Phillips Adapter Patent # 5,038,435 CHE800S Hex End for #8 Tool (/4 ) CSTS Con-Sert #8 Tool Sleeve only MOST ORDERS SHIPPED THAT SAME DAY! A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC. CHARLES CITY, IOWA 800-833-647 Fax 64-228-624 www.dfsusa.com

CON-SERT TOOLS FOR DRILLING AND DRIVING CON-SERT SCREWS CON-SERT TOOL FEATURES: SELF-CONTAINED ONE MAN/ONE TOOL DRILL AND DRIVER SYSTEM UNIQUE SELF-RETRACTING CARBIDE BIT ADJUSTABLE DEPTH SETTINGS REPLACEABLE HEX END ZINC & DICROMATE PLATED HARDENED PHILLIPS DRIVER INCLUDED ADAPTER FOR TLS HAMMER DRILLS IS NOW AVAILABLE HEAVY-DUTY STORAGE TUBE INCLUDED WHAT ADVANTAGES ARE THERE? The dual-purpose Con-Sert Tools allow you to drill the hole and drive the screw through the object and into the concrete eliminating the need to line up the holes! The Con-Sert Tool can drill through Light Steel Wood Brick and into Concrete. Preset drill bit to desired hole depth and drill through wood, light steel or concrete in one operation. 2. With drill motor still turning clockwise, withdraw bit from hole. Drill bit will automatically retract into Con-Sert Tool exposing hex driver. 3. CON-SERT I and #8 with self retracting drill bits make Con-Sert Screw installation a one man, one tool operation. HOW TO REMOVE THE CON-SERT HEX END! Insert Con-Sert Screw into hex end and drive screw into the predrilled hole. (for phillips head screws, insert phillips driver into Con-Sert Tool hex driver). CLAMP THE CON-SERT TOOL CHUCK END INTO. INSERT A 90 HEX WRENCH INTO THE HEX. SCREW IN THE NEW HEX END IN THE "Clockwise" A BENCH VISE, WITH HEX END UP. (NOTE: DO NOT CLAMP "TOOL BODY" IN THE VISE OR IT WILL CRUSH THE TOOL.) END. Con-Sert I = 5/6" Hex wrench Con-Sert #8 = /4" Hex wrench 2. STRIKE THE HEX WRENCH WITH A SHARP BLOW IN THE "Counter-Clockwise" DIRECTION TO BREAK LOOSE HEX END. (NOTE: Con-Sert #8 Tool Drill Bit must be removed from tool first.) DIRECTION. (Note: The new hex end will fully tighten when you set your first few Con-Sert Screws!!!) Copyright 200, Diversified Fastening Systems, Inc.

CON-SERT HLS SERIES CONCRETE SCREWS 3/6 & /4 DRILL & DRIVER (FOR BLUE SCREWS) WITH BLUE DYNASEAL COATING PATENT # 4,954,0 The Con-Sert HLS Concrete Screws are the standard "high-low thread" hardened steel screws designed for cutting threads into a predrilled hole in poured concrete, block and brick. The Con-Sert HLS has a sharp "gimlet" point for easy starting and piercing of most all light gauge materials. The Con-Sert HLS Tools are the NEW & PATENTED way to anchor all "high-low thread" concrete screws. These tools also work with all Tap-Con* type screws. The dual purpose Con-Sert HLS Tools allow you to drill the hole and drive the screw through the object being anchored and into the concrete eliminating the need to line up the holes! Con-Sert HLS Tools SIZES AND ACCESSORIES Con-Sert Tool #4 (for 3/6") Con-Sert Tool #5 (for /4") #2 Phillips Driver (for 3/6") #3 Phillips Driver (for /4") 5/32" Drill Bit (for 3/6") 3/6" Drill Bit (for /4") Con-Sert HLS Screws SIZES AVAILABLE - HEX OR PHILLIPS 3/6 x /4" 3/6 x 3/4" 3/6 x 2 /4" 3/6 x 2 3/4" 3/6 x 3 /4" 3/6 x 3 3/4" 3/6 x 4" /4 x /4" /4 x 3/4" /4 x 2 /4" /4 x 2 3/4" /4 x 3 /4" /4 x 3 3/4" /4 x 4" /4 x 5" /4 x 6" Meets I.C.B.O Standards See Report No. 494 The Con-Sert Tool HLS works with these name brands... DFS/USA ITW Olympic Rawl Dual US Anchor HLS Concrete Screws Tap-Con Ruff-Nex Tapper Tite'N Concrete Screws S MO ED P IP AY! H S D S ME R DET SA R O A ST TH UP CHARLES CITY, IOWA 800-833-647 Fax 64-228-624 A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC.

CON-SERT HLS SCREWS CON-SERT HLS TOOLS WILL ELIMINATE AND REPLACE PLASTIC PLUGS AND LEAD ANCHORS CASE HARDENED STEEL SCREW WITH A SERRATED HIGH-LOW THREAD DESIGN SHARP "GIMLET" POINT FOR EASY STARTING DYNASEAL "BLUE" COATING FOR CORROSION RESISTANCE CON-SERT HLS SCREWS ARE AVAILABLE IN: 3/6" Hex Head (Slotted) 3/6" Phillips Flat Head /4" Hex Head (Slotted) /4" Phillips Flat Head CON-SERT HLS SCREWS ARE PACKAGED: Count Box with carbide drill bit Bulk with/without bits PATENT # 4,954,0 SELF-CONTAINED ONE MAN & ONE TOOL DRILL AND DRIVER SYSTEM UNIQUE SELF-RETRACTING CARBIDE BIT ADJUSTABLE DEPTH SETTINGS REPLACEABLE DRILL BIT AND HEX END WORKS WITH HEX & PHILLIPS SCREWS ADAPTER FOR SDS ROTO HAMMER USE IS AVAILABLE NEW Phillips Driver (included) holds the driver where you want it... NOTE: Con-Sert HLS Screws /4" Recommended Embedment Also includes hex wrench for drill bit changes... CON-SERT HLS SERIES INSTALLATION PROCEDURE PATENTED (" to 3/4" Recommended Embedment) - PRESET EMBEDMENT - DRILL HOLE - INSERT SCREW INTO HEX DRIVER DEPTH SETTINGS /4" to /2" 2" to 2 /4" 2 /2" to 3" - DRIVE SCREW INTO PILOT HOLE FOR PHILLIPS SCREWS... SNAP ON PHILLIPS DRIVER Extend bit into desired depth notch. Drill into masonry /4" deeper than the screw length. (Use lower RPM for dense concrete) Insert hex screw into end of tool (for phillips screws attach the DFS Phillips Driver) Drive screw into pilot hole to fasten object. (rotary only) What length of screw should I use? AVERAGE CONCRETE Thickness of Material + /4" = Screw Length Copyright 2000, DFS/USA, Diversified Fastening Systems, Inc.

SPLIT DRIVE ANCHORS FOR FASTENING TO CONCRETE, BRICK AND STONE FLAT HEAD ROUND HEAD The Split Drive Anchor is a one piece carbon steel anchor for light-duty anchoring to all masonry. Split Drives are available in round head or flat head styles. FLAT HEAD SIZES AVAILABLE ITEM NUMBER 42SF 4200SF 422SF 4300SF 432SF 4400SF A safety factor of 4:, or % of ultimate, should be used. Critical applications (vibratory loads, overhead installations, etc.) may require a safety factor of as much as 0: or more. INSTALLATION PROCEDURE QTY SIZE /4 x /2 /4 x 2 /4 x 2 /2 /4 x 3 /4 x 3 /2 /4 x 4 ITEM NUMBER 44SR 42SR 4200SR 422SR DIAMETER /4" ROUND HEAD SIZES AVAILABLE QTY SIZE /4 x /4 /4 x /2 /4 x 2 /4 x 2 /2 TEST PERFORMANCE DATA EMBEDMENT PULL-OUT /8" 2000 lbs. All tests conducted in 3700 psi concrete. GSA Spec. FF-S-3, Group IV. 2. 3. Dril Hole (Same Diameter as Anchor) Drive in with Hammer SET! MOST ORDERS SHIPPED UPS THAT SAME DAY! A product of the American-do spirit. DIVERSIFIED FASTENING SYSTEMS INC. CHARLES CITY, IOWA 800-833-647 Fax 64-228-624

ROUND HEAD FLAT HEAD SPLIT DRIVE ANCHORS FOR FASTENING TO CONCRETE, BRICK AND STONE WORKS IN POURED CONCRETE, CONCRETE BLOCK, BRICK AND STONE DRILL SAME HOLE DIAMETER AS THE ANCHOR DIAMETER ZINC PLATED FOR CORROSION RESISTANCE MEETS ASTM B-633 AVAILABLE IN OPEN STOCK BOXES OR BULK WHAT ADVANTAGES ARE THERE? Easy to install! A drill and hammer are the only tools needed to install the split drives. They also offer a relatively high pull-out strength at a low cost. WHERE DO I USE SPLIT DRIVE ANCHORS? Thresholds Handles & Guard Rails Window Frames Signs Trim Edges Light Fixtures Wood To Concrete Sheet Metal To Concrete Vent Covers Mail Boxes Copyright 2000, DFS/USA, Diversified Fastening Systems, Inc.