PMC-2520B/2540B/2550B Step Motor Driver User's Manual (V1.3) 健昇科技股份有限公司 JS AUTOMATION CORP. 新北市汐止區中興路 100 號 6 樓 6F., No.100, Zhongxing Rd., Xizhi Dist., New Taipei City, Taiwan TEL:+886-2-2647-6936 FAX:+886-2-2647-6940 http://www.automation.com.tw http://www.automation-js.com/ E-mail:control.cards@automation.com.tw
Correction record Version Record 1.1 Add PMC2550B 1.2 Add P.7 current setting description for different connection 1.3 Add Warranty 1
Contents 1 Features... 4 2 Specifications... 4 3 I/O Functions... 5 4 LED indicator... 6 5 Control signal... 6 6 Wiring diagrams... 7 7 Dimension... 9 2
Warranty The PMC-2520B/2540B/2550B are warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by receipts or serial no. on board. JS automation Corp. will, at its option, repair or replace product that proves to be defective during the warranty period. This warranty includes parts, labor and shipping costs of returning. Except as specified herein, JS automation Corp. makes no warranties, express or implied, and specifically disclaims any warranty of merchantability or fitness for a particular purpose. Customer s right to recover damages caused by fault or negligence on the part of JS automation Corp. shall be limited to the amount theretofore paid by the customer. JS automation Corp. will not be liable for damages resulting from loss of data, profits, use of products, or incidental or consequential damages, even if advised of the possibility thereof. This limitation of the liability of JS automation Corp. will apply regardless of the form of action, whether in contract or tort, including negligence. Any action against JS automation Corp. must be brought within one year after the cause of action accrues. JS automation Corp. shall not be liable for any delay in performance due to causes beyond its reasonable control. The warranty provided herein does not cover damages, defects, malfunctions, or service failures caused by owner s failure to follow the JS automation Corp. installation, operation, or maintenance instructions; owner s modification of the product; owner s abuse, misuse, or negligent acts; and power failure or surges, fire, flood, accident, actions of third parties, or other events outside reasonable control. If any defect occurs, you should email to us as the following form to get the fast response: Detailed Company Information Company/Organization: Contact Person: E-mail: Address: Country: Tel/Fax: Web Site: Product information product model: serial no.: Environment to Use: such as CPU board, Operating System, target application... description of defect: (as detail as possible) 3
1 Features 1.1 High torque and heavy load design 1.2 PWM constant current source 1.3 Full/ Half step selection 1.4 Build in overheat protection 1.5 Build in auto power down mode 2 Specifications Model PMC-2520B PMC-2540B PMC-2550B Driving Mode PWM Switching, Bipolar with Constant Current Driving Maximum Current 2A/Phase 4A/Phase 5A/Phase Resolution Full Step : 1.8 o /per step, Half Step : 0.9 o /per step Input Signal Optically isolated, Voltage : H : +4V ~ + 24V, L : +0 ~ +5V. Resistance 220Ω, Current Under 20mA. CW and CCW Pulse Signal : Pulse Width : Above 5µSec. Direction Signal : LOW for CW, HIGH for CCW. Holding Current OFF Signal : HIGH for Release Holding. Output Signal Photo-Coupler Open Collector. Voltage : Under 24V, Current : Under 15mA. Step 0 Signal Overheat Signal DIP Selectors Auto-Current-Down Auto-Over-Heat Protection 1P / 2P signal Input Method Selector Full/Half Step Selector LED Indicators Step 0 Status LED Over-Heat Alarm LED Power LED Operation Temperature 0 ~ 45 Operation Humidity < 85% RH Power source 110 VAC ±10%, 60Hz Dimension 158mm(L) x 130mm(W) x 52mm(H) Weight 770g 4
3 I/O Functions DIP Selectors Current Selectors 1- frame ground 2-110V AC power inputr 3- output to step motor 4- over heat signal out 5- STEP0(excitation phase 0) signal out 6- input of Holding Current Off 7- CCW/DIR input CCW for dual pulse mode DIR for single pulse mode 8- CW/PLS input CW for dual pulse mode PLS for single pulse mode 9- User option mode ACD, auto current down Auto current down while no pulse in. Use this function to reduce the heat of step motor, but if you need to hold the torque while stand by, switch off to disable this function AOH, auto overheat protection Switch on to enable the auto overheat protection. While the driver case reaches 80 degree C, the AOH circuit will stop the driver and activate the AOH led. 1P /2P mode 1P mode: Pulse (PLS) and direction (DIR) controls the motion operation. 2P mode: Clockwise(CW) and counter- clockwise(ccw) controls the motion operation. FULL/HALF step mode FULL step: 1.8 degree per step HASLF step : 0.9degree per step 10- STOP current adjustment Only valid for ACD is enabled. While ACD function enabled and the pulse train is stopped for more than 0.5s, the motor current will decrease to the adjustment value. 11- RUN current adjustment Motor current while running. 5
4 LED indicator 4.1 POWER: green LED, power OK will light. 4.2 O.H.: red LED, light for over heat while AOH is enabled. 4.3 STEP 0: yellow LED, light for excitation phase 0, in full step mode, it will light every 4 steps and for half step mode every 8 steps. 5 Control signal 5.1 The control signal is isolated by photo-isolator and the external signal transit state from HIGH to LOW will drive one step. 5.2 The minimum pulse width is 5 micro second, the transition time is less than2 micro second. 5.3 The input voltage range is from 5VDC to 24VDC and the current must limit to under 20ma. 5.4 The driver output signal is limited to under 15ma. Input Signal circuit Pulse Width Diagram Output Signal circuit 6
6 Wiring diagrams 6.1 4 Leads 4 Leads *NC = Not connected to anything 6.2 6 Leads *NC = Not connected to anything 6 Leads 6 Leads Series Connected Center Tap Connected Note: MPC25xx is a bipolar driver, if using unipolar winding motor, connect as 6 leads series connect and the driver current setting must set at half of rated current /phase. 6.3 8 Leads *NC = Not connected to anything 8 Leads 8 Leads Series Connected Parallel Connected Note: MPC25xx is a bipolar driver, if using unipolar winding motor, connect as 8 leads series connect and the driver current setting must set at half of rated current /phase. 7
Notes on wiring: *Be sure to power off while motor is being wired. *Wrong wiring or wire may damage the driver. *The external force cooling is required, if you the driver case temperature is higher than 55 degree C at normal operation. *Please use the driver at good ventilation environment. *Please do not use the driver at wet or the environment may have condensed water. 8
7 Dimension Approx. Current Adjustment and Auto current down % List 2520B 2540B ACD% 0 0.23A 0.56A 015% 1 0.26A 0.70A 021% 2 0.40A 0.90A 026% 3 0.50A 1.20A 032% 4 0.66A 1.40A 038% 5 0.80A 1.52A 043% 6 0.89A 1.66A 049% 7 1.05A 1.86A 055% 8 1.10A 2.10A 060% 9 1.31A 2.32A 066% A 1.43A 2.54A 071% B 1.61A 2.80A 077% C 1.73A 3.10A 083% D 1.86A 3.40A 088% E 2.00A 3.70A 094% F 2.14A 4.00A 100% 9