Brandt Automatic Edgebander Optimat Model KDF 670 2C PC-16 Program Control: - Color matrix LCD screen display - 8mb RAM - Manual push button controls or program control operation Equipped with digital height indicator. Integrated electronic line control system for increased reliability. Universal automatic magazine for strip and coil feeding. Adjustable in feed fence. Joint trimming unit for pre-trimming the work piece edge prior to processing. Quick melt granulate glue application system with twelve minute heat-up time. Quick-change glue tank for easy maintenance and glue color change, if necessary. Infrared radiant quartz heating unit between glue roller and pressure zone for optimum gluing strength. First pressure roller driven and two idle pressure rollers. Double motor end trimming unit with straight and chamfer capability. Chamfer up to 15. Program controlled indexing from straight to bevel end trimming. Fine trimming unit #1 with digital Quickset system. Tilt range 0-25. Program controlled indexing. Fine trimming unit #2 with digital Quickset system. Tilt range 0-25. Program controlled indexing. Contour trimming unit for profile corner trimming. Sound enclosure with centralized dust extraction outlet. Scraping unit for rigid PVC edges. Program controlled indexing. Buffing unit. Electronic frequency changer for all trimming motors which also incorporates electronic motor brakes. Electrical components according to UL/CSA Listings.
Page 2 Technical Specifications Edge band thickness 0.4 12 mm (0.016" - 1/2 ) Coil cutoff maximum 0.8 x 45 mm 3.0 x 45 mm (PVC) Edgeband height 12-60 mm (1/2" 2 3/8 ") Panel length min. 160 mm (6 3/8") Panel width min. 65 mm (2 3/8") Panel thickness - min. 8 mm (5/16") - max. Feed speed two speeds Feed motor Joint trimming unit two motors Cutting speed Pressure section End trim unit - two motors Cutting speed Straight cut max. Fine trimming unit Tilting range Cutter speed Fine trimming unit Tilting range Cutter speed Profile trimming unit - top and bottom Total power required Amperage @ 230 55 mm (2 3/16") 14 m/min (46 FPM) and 11 m/min ( 36 FPM ) when using the contour trimming unit. 2.2 kw (3 HP) 2.2 kw ( 3 HP each ) First roller driven, two rollers idle.27 kw (1/3 HP ea) 5 x 45 mm (3/16" x 1 3/4").55 kw (3/4 HP each) 0-25.55 kw (3/4 HP each) 0-25 0.3 kw (1/2 HP ea - two motors) 7 kw 50 amps 25 amps @ 460 Machine length 6740 mm (22' 2 ) Machine width 1730 mm (68") Working height 900 mm (35.5") Total height 1600 mm (63") Machine net weight 2800 kg (6160 lbs.) Electrical connection: 208/230 or 440/480 volt, 3-phase, 60 Hz. Dust extraction: 2x 100 mm (4"), 1000 CFM. Compressed air connection: 0.18 CFM per panel, 6 bar (85 PSI).
Page 3 Automatic Height Adjustment with Top Pressure Beam for All Top Work Stations PC-16 Program Control Integrated Electronic Line Control System for Increased Reliability Joint Trimming Unit pre-trimming of the workpiece edge prior to gluing two motors, 3 HP each, one motor clockwise rotation, one counter-clockwise vertical spindle adjustment via digital settings horizontal positioning via electro-pneumatic control dust extraction hood included with 120 mm diameter outlet ( 4 ¾ ) diamond cutter heads. Automatic Magazine for Strip and Coil Feeding large coil table (800 mm diameter) with built-in rollers to allow for 3 mm PVC coils edge strip capacity from 0.4 mm to 8mm (0.016 5/16 ) direction of glue roller reversible glue roller section is also retractable from fence line one large driven pressure roller with pneumatic pressure control two secondary rollers, all with controlled side pressure setting of pressure zone equipped with digital counter accurate to.1 mm (.004) strengthened precutter for cutting thick PVC edges from the coil; maximum 3 x 45 mm; precutting system equipped with air volume reservoir for ondemand activation required for short workpieces Quick Melt Gluing System heat-up time is ten minutes hopper feeding gluing system no lubrication required using high tech bearing system pneumatic locking of the unit for gluing the last two inches of the workpiece quick-change glue tank for easy maintenance and glue color change, if necessary glue temperature indication of both pre-melter and glue roller via LED thermostat display visible to operator infrared radiant glue heat zone control for optimum gluing strength. Automatic temperature reduction if not run within 15 minutes. This feature reduces the temperature automatically to 150 degrees C.
Page 4 Sound Cover equipped with three independent openings safety interlock system - when sound enclosure door is opened, corresponding work station shuts off end trimming, fine trimming, and top/bottom contour trimming motors are each equipped with electronic motor brakes to stop cutter rotation when hood is opened or when station is shut off at operator control panel End Trimming Station straight/chamfer end trim unit equipped with two 0.27 kw (1/3 HP) 12,000 RPM motors; electronic motor brakes end trim unit utilizes drawing cut system for reduced blade projection when working on thick panels tooling also included program controlled indexing from straight to bevel end trimming Fine Trimming Unit #1 equipped with two.55 kw (3/4 HP) trimming motors electronic motor brakes horizontal and vertical tracing wheels with lateral location indexing via digital Quickset system calibrating to.1 mm (.004 ) tilting from 0-25 each trimming motor is equipped with one dust hood and dust extraction hose equipped with two straight cutter heads, flush trimming possible up to 8 mm edge thickness. Fine Trimming Unit #2 equipped with two.55 kw (3/4 HP) trimming motors electronic motor brakes horizontal and vertical tracing wheels with lateral location indexing via digital Quickset system calibrating to.1 mm (.004 ) tilting from 0-25 each trimming motor is equipped with one dust hood and dust extraction hose equipped with two combination straight/radius cutterheads, including four knife carbide inserts set at shear angle for optimum surface quality finish; flush trimming possible up to 8 mm edge thickness; radius - 3 mm
Page 5 Contour Trimming Unit for rounding front and trailing corners of workpieces with 3 mm PVC edgings includes two trimming motors 0.3 kw (1/2 HP) ; electronic motor brakes equipped with 3 mm radius insert cutterheads reversible Scraping Unit with Knives for scraping of roughly trimmed thick PVC edges in order to remove the cutter marks Quickly changeable Tracing wheels both vertical and horizontal 3 mm radius reversible profile knives standard Top and Bottom Buffing Unit top and bottom buffing motors for finishing of longitudinal edges two 2800 RPM polishing motors inclinable vertically and horizontally two buffing wheels included Altendorf America Leasing Option Stiles Machinery offers a variety of flexible financing options to meet your needs. Contact your sales representative for a detailed leasing quote at current rates. Installation Any required change of voltage will be performed at time of installation, not prior to shipment. IN CASE OF INCOMING MAIN VOLTAGE FLUCTUATIONS OF MORE THAN +5% / - 5% OF MACHINE CONNECTED VOLTAGE, A VOLTAGE STABILIZER MUST BE INSTALLED BY THE CUSTOMER ON THE INCOMING POWER CONNECTION. ALTENDORF AMERICA STANDARD TERMS AND CONDITIONS OF SALE ARE APPLICABLE.