SVENSK STANDARD SS-EN ISO 4029:2004 Fastställd 2004-01-09 Utgåva 1 Fästelement Stoppskruvar med sexkantshål och skål (ISO 4029:2003) Hexagon socket set screws with cup point (ISO 4029:2003) ICS 21.060.10 Språk: engelska Publicerad: mars 2004 Copyright SIS. Reproduction in any form without permission is prohibited.
Europastandarden EN ISO 4029:2003 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN ISO 4029:2003. The European Standard EN ISO 4029:2003 has the status of a Swedish Standard. This document contains the official English version of EN ISO 4029:2003. Upplysningar om sakinnehållet i standarden lämnas av SIS, Swedish Standards Institute, telefon 08-555 520 00. Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS Förlag AB, 118 80 STOCKHOLM Telefon: 08-555 523 10. Telefax: 08-555 523 11 E-post: sis.sales@sis.se. Internet: www.sis.se
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO 4029 December 2003 ICS 21.060.10 English version Hexagon socket set screws with cup point (ISO 4029:2003) Vis sans tête à six pans creux, à bout cuvette (ISO 4029:2003) Gewindestifte mit Innensechskant mit Ringschneide (ISO 4029:2003) This European Standard was approved by CEN on 4 November 2003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4029:2003 E
Page 2 EN ISO 4029:2003 Provläsningsexemplar / Preview Foreword This document (EN ISO 4029:2003) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and nonthreaded mechanical fasteners and accessories", the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn at the latest by June 2004. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom. NOTE FROM CMC The foreword is susceptible to be amended on reception of the German language version. The confirmed or amended foreword, and when appropriate, the normative annex ZA for the references to international publications with their relevant European publications will be circulated with the German version. Endorsement notice The text of ISO 4029:2003 has been approved by CEN as EN ISO 4029:2003 without any modifications.
Page 3 EN ISO 4029:2003 Hexagon socket set screws with cup point 1 Scope This International Standard specifies the characteristics of hexagon socket set screws with cup point and threads from M1,6 up to and including M24 and of product grade A. If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e.g. ISO 261, ISO 898-5, ISO 965-2, ISO 3506-3 and ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and designations of dimensions ISO 261, ISO general-purpose metric screw threads General plan ISO 898-5, Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners not under tensile stresses ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads ISO 3269, Fasteners Acceptance inspection ISO 3506-3, Mechanical properties of corrosion-resistant stainless-steel fasteners Part 3: Set screws and similar fasteners not under tensile stress ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings ISO 23429, Gauging of hexagon sockets
Page 4 EN ISO 4029:2003 Provläsningsexemplar / Preview 3 Dimensions See Figure 1 and Table 1. Symbols and designations of dimensions are specified in ISO 225. Permissible alternative form of socket For broached sockets which are at the maximum limit of size, the overcut resulting from drilling shall not exceed 1/3 of the length of any flat of the socket which is e/2. a The 120 angle is a requirement for short-length screws of nominal length, l, situated in the shaded areas in Table 1. b The 45 angle applies only to the portion of the point situated below the root diameter of the thread. c Incomplete thread u<2p. d A slight rounding or countersink at the mouth of the socket is permissible. Figure 1