Nordc - 2 oor Wardrobe ssembly Instructons - lease keep for future reference 62967 mensons Wdth : 8. cm epth : 49,0 cm Heght : 9, cm Important - lease read these nstructons fully before startng assembly If you need help or have damaged or mssng parts, call the ustomer Helplne: 0845 640 0 0 440050 66569-20--20
Safety and are dvce Important - lease read these nstructons fully before startng assembly heck you have all the components and tools lsted on pages and 4. Remove all fttngs from the plastc bags and separate them nto ther groups. Keep chldren and anmals away from the work area, small parts could choke f swallowed. Make sure you have enough space to layout the parts before startng. o not stand or put weght on the product, ths could cause damage. ssemble the tem as close to ts fnal poston (n the same room) as possble. ssemble on a soft level surface to avod damagng the unt or your floor. arts of the assembly wll be easer wth 2 people. We do not recommend the use of power drll/drvers for nsertng screws, as ths could damage the unt. Only use hand screwdrvers. spose of all packagng carefully and responsbly. are and mantenance Only clean usng a damp cloth and mld detergent, do not use bleach or abrasve cleaners. From tme to tme check that there are no loose screws on ths unt. hs product should not be dscarded wth household waste. ake to your local authorty waste dsposal centre. Note: f requred the next page can be cut out and used as reference throughout the assembly. Keep ths page wth these nstructons for future reference. 2
omponents - anels If you have damaged or mssng components, call the rgos ustomer Helplne: 0845 640 0 0 lease check you have all the panels lsted below Sde, Left 5584 8x475x5 mm 2 Sde, Rght 5587 8x475x5 mm op/bottom x2 55864 78x470x5 mm 4 lnth, back 55866 78x60x5 mm 6 op ral 55806 792x80x5 mm 5 lnth, front 5580 79x96x5 mm 8 oor x2 55822 725x95x5 mm 7 Back x2 NM4585 74x97x mm 0 Hangng ral L22005-77 77x22x5 mm 5 H-profle B8700-700 4x700 mm
omponents - Fttngs If you have damaged or mssng components, call the rgos ustomer Helplne: 0845 640 0 0 lease check you have all the panels lsted below Note: he quanttes below are the correct amount to complete the assembly. In some cases more fttngs may be suppled than are requred. G B090 ø8x0 mm wooden dowel x0 B0468 ø40x0 mm Wooden knob x2 R L B070 ø4,0x5 mm screw x2 B0050 ø,5x5 mm screw x22 B07 5x22 mm support for hanger x2 M N B0590 ø5x9,5 mm cam x4 B075- ø0x8 mm magnet x4 B075-2 ø0x8 mm magnet catch x4 J B060 ø5/x4 mm bolt x4 B0025 ø,2x20 mm nal x50 B080 20x20x2 angle x4 B0240 ø6,x,5 mm screw x8 Y B82002 wallstrap and nstructon B052 0 mm/7 mm crossplate x6 W B0508 ø26 cup hnge x6 Ba0688 500x250x Nal holder x B085 50x50x2 mm angle x2 ools requred Ruler - Use ths ruler to help correctly dentfy the screws 4
ssembly Instructons Step Knock down the owels nto the holes ndcated on top/bottom and the back plnth 4 usng a small hammer. M M x2 4 ress the magnets M nto holes ndcated. M M Step 2 Fx the support for hanger ral L to the sdes and 2 usng screws. Fx the crossplates to the sdes and 2 usng the premounted screws. See detals. poston the crossplate exactly as shown. Screw the bolts nto the holes ndcated. Fx the angles to the sdes and 2 usng screws. lace the angles as shown. See detals. L L L 2 5
ssembly Instructons Step lace the sdes and 2 onto the top, the back plnth 4 and the bottom. ush cams nto holes ndcated, arrows pontng towards sdes. urn the cams to the rght to fx the top and bottom and the back plnth 4. See detals. 2 4 Step 4 Fx the front plnth 5 onto the angles usng screws. 4 2 5 6 5
ssembly Instructons Step 5 lace the backs 7 nto rebates n the sdes,2 and nto the H-profle 5.! Important! Make sure the angle between the top and the sdes s 90 when the back s attached. 90.0 5 7 7 Fx the backs to the sdes,2, the top and the back plnth 4, usng nals. Use the nal holder Yd and a small hammer. 2 Step 6 lace the cup hnges nto the holes ndcated on the doors 8. Fx the hnge usng screws. N 8 8 N lace the magnet catches N n the holes ndcated on doors 8, usng a small hammer. 8 x2 N 7
ssembly Instructons Step 7 lace the top ral 6 onto the top. Fx the top ral to the top usng angles W and screws W 6 W W 6 Step 8 0 lace the hanger ral 0 nto the support L. 0 L L o fx the doors 8, slde the cup hnges onto the crossplates. Fx the hnges usng the pre-mounted screw n the crossplates. See detals. Fx the wooden knobs G to the doors usng screws R. 8 8 G R R G ghten these screws R G x2 8
ssembly Instructons Step 9! Warnng! he wardrobe s heavy. Lft wth care. Its recommended that the wardrobe s fxed to the wall. Wallstrap and nstructon Use the fttngs J. Follow the nstructon ncluded wth the fttngs. 9
ssembly Instructons Step 0 djustng the doors left/rght. a: o adjust the door towards the left hand sde - turn the adjustng screw to the rght. b: o adjust the door towards the rght hand sde - turn the adjustng screw to the left. djustng the doors forwards/backwards. a: Loosen the fxng screw. b: ush the cup hnge/the door forwards or backwards to adjust. c: ghten the fxng screws of LL the crossplates. djustng the doors up/down. a: Loosen the two pre-mounted screws of each crossplates, BU ONLY as much as t wll allows the crossplates to move up and down. b: ush the door up or down to adjust. c: ghten the pre-mounted screws of LL crossplates. If you need help or have damaged or mssng parts, call the ustomer Helplne: 0845 640 0 0 Home Retal Group - 489-499 vebury Boulevard - Saxon Gate West - entral Mlton Keynes MK9 2NW 0