John Lewis ELLIS 2 DOOR 2 DRAWER SIDBOARD Stock Number: 87702732 Thank you for purchasing this Ellis 2 Door 2 Drawer Sideboard. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Pre-assembly preparation Please ensure instructions are read in full before attempting to assemble this product. Necessary Tools ( Included ) A cross head screwdriver only should be used to assemble this unit, an electric drill may cause damage to the product and is not recommended. Please check the pack contents before attempting to assemble this product. A full checklist of components is given in this leaflet. If any components are missing, please contact the retailer from whom you bought this product. This product takes approximately 90 MINUTES to assemble with 2 PEOPLE. All assembly should be performed on a flat, stable, clean and soft surface. This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product The fitting pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN. IMPORTANT: Retain these instructions for future reference.. Page :
3 6 6 5 2 8 7 4 8 2 0 7 3 9 Page : 2
s and parts checklist 2 3 4 5 Right side panel Left side panel Top panel Bottom panel Partition panel x x x x x 6 Back panels 7 8 9 0 Doors Removable shelfs Drawer fronts Right drawer sides 2 3 Left drawer sides Drawer backs Drawer bottoms A B Hinge Hinge mounting plate x 4 x 4 J K Door stopper Wood shelf support x 4 x 8 Small minifix bolt S Ø6 x 34 x 8 T Small minifix housing Ø2 x 0.2 x 8 C Varianta cross head screw Ø4 x 0.5 x 6 L Round cross head screw Ø4 x 5 7 U Round cross head screw Ø4 x 30 x 8 D E Hex head screw hex head screw Ø7 x 50 Large minifix bolt Ø7 x 34 x0 M N Flat washer Ø5 x 2 x Hex key x 5 x F Large minifix housing Ø5 x 2.5 x0 P Hinge cover cap x 4 (Wall fixing kit) G Dowel Ø8 x 30 x 2 Q Metric cross head bolt Ø4 x 30 x 4 H Flat cross head screw Ø3 x 2 x 4 R Handle x 4 Page : 3
Wall fixing - if in doubt seek professional advice Page : 4
Step By Step Assembly Instructions Step : Attach 4 x dowels (G) into right side panel ( ) and left side panel (2) : Attach 0 x large minifix bolts (E) into right side panel ( ), left side panel (2) and and top panel (3) : Attach 4 x hinge mounting plates (B) to right side panel ( ) and left side E panel (2) using 8 x varianta cross head screws (C) as shown. G E x 0 G x 4 2 B x 4 E B C G B C C x 8 3 E : Attach 4 x dowels (G) to bottom panel (4). : Attach 4 x hinges (A) to 2 doors (7) using 8 x varianta cross head screws (C). G x 4 4 A x 4 A C C x 8 7 x2 G Page : 5
Step 2 : Attach 4 x dowels (G) to partition panel (5) : Attach 4 x door stoppers (J) to partition panel (5) using 4 x flat cross head screws (H). G x 4 G J x 4 5 H x 4 J G H Step 3 : Attach partition panel (5) to bottom panel (4) using 2 x hex head screws (D) use hex key (N) to tighten. D 5 N x 4 D N Page : 6
Step 4 : Attach right side panel () to bottom panel (4). : Insert 2 x minifix housings (F) into bottom panel (4). : Use screwdriver to turn minifix housings (F) clockwise to fix. F 4 F Step 5 : Attach left side panel (2) to bottom panel (4). : Insert 2 x minifix housings (F) into bottom panel (4). : Use screwdriver to turn minifix housings (F) clockwise to fix. F 4 2 F Page : 7
Step 6 : Attach top panel (3) to left side panel ( 2), right side panel () and partition panel (5). : Insert 6 x minifix housings (F) into left & right side panels and partition panel as shown. : Use screwdriver to turn minifix housings (F) clockwise to fix. F x 6 3 F 5 2 Step 7. Attach 2 x back panel (6) to back of unit using 22 x round cross head screws (L) along outside edge. 2. Use 5 x round cross head screws (L) with 5 x washer (M) to attach back panel to partition panel (5). L 7 M x 5 6 L 6 L Step M Step 2 Page : 8
Step 8 : Position hinges (4) on doors (7) onto hinge mounting plates (B) in left side panel (2) and right side panel () as shown. Step 2 Step 2 Page : 9
Step 9 by screw adjustment. HINGE ADJUSTMENT INSTRUCTIONS (9.2) FRONT-TO-BACK by slackening and retightening the hinge-arm mounting screw. via slots on mounting plate by slackening and retightening the screws on mounting plate Page : 0 IW-0-000-0060-0 (Type 2)
Step 0 : Attach 4 x hinge cover cap (P) to hinges as shown. : Attach 2 x handles (R) to doors (7) using 2 x metric cross head bolts (Q). : Attach 8 x wood shelf supports (K) to pre-drilled holes on left side panel, partition panel and right side panel as shown. : Place removable shelves (8) onto previously attached wood shelf supports. P x 4 R Q K x 8 Step 8 8 K R Page :
Step Assembly instructions for drawer box. For parts 9, 0,, 2 and 3. : Attach 8 x small minifix bolts (S) to both drawer fronts (9) as shown. : Place right drawer sides (0) and left drawer sides () onto drawer fronts (9) use screwdriver to turn minifix housings (T) clockwise to fix as shown. S x 8 S T x 8 0 x2 T x2 9 x2 9 x2 : Slide drawer bottoms (3) into the grooves of right drawer sides (0), left drawer sides () and drawer fronts (9) as shown. : Place drawer backs (2) onto left & right drawer sides and drawer bottoms (3) 2 x2 : Fix drawer backs (2) in place using 8 x round cross head screws (U). U x 8 2 x2 3 x2 U 9 x2 Page : 2
Step 2 : Attach 2 x handles (R) to drawer fronts (9) using 2 x metric cross head bolts (Q). : Place drawers into unit. R Q Q R Complete Page : 3
Care and Maintenance Wood Furniture Wood displays different grain patterns depending on which way they are cut - for example, the 'medullary ray' which can appear on oak furniture is a mark of good quality timber - these are just characteristics of the natural beauty of the wood. Some furniture is also deliberately aged and rustic. Wood veneers also allow distinctive patterns to be created on some surfaces, such as table tops and drawer fronts by the way slivers are arranged. All timber and veneer surfaces will change colour and mellow over time. New furniture will initially vary in shade from items that have been previously purchased. How to care for your wood furniture Dust with a clean, damp, lint free cloth. Frequent dusting will remove abrasive build up, which can damage the finish over time. Do not use a very wet cloth or allow any liquid to contact with the veneers for a long period of time as this can permanently damage the surface. Wipe up spills immediately. Do not use any abrasive cleaner or harsh detergent as this can damage the surface of the furniture. Spray polishes are best avoided as they contain silicones which may spoil the furniture's surface by building up over time. Make sure all surfaces are protected from heat and liquids by mats and coasters. Ensure that a mat or pad is placed under paper when you are writing on the furniture surface. Do not place rubber or plastic materials on the wood finish as chemicals within may react with the finish if left in contact for an extended period of time. Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next to heat sources such as radiators or fires. Be particularly careful with solid wood as the lack of humidity caused by home heating can cause damage such as warping, cracking or splitting. Excessive exposure to sunlight can cause fading of your furniture. Safety Instructions: Never drag furniture when moving it. Always lift it. Periodically check all fixings to ensure none have come loose. Re-tighten when necessary. Please take care when handling or moving the furniture as careless handling may cause damage or injury. Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent person. No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture. Heavy item warning: It is recommended to seek assistance when moving a heavy object. Take care when lifting to avoid personal injury and (or) damage to the product. It is recommended that before moving the heavy object to a new location it is completely dis-assembled to avoid personal injury or damage to the furniture. Please be careful to retain all fitting when doing this. PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE John Lewis Partnership 7 Victoria Street, London, SWIE 5NN www.johnlewis.com Page : 4