SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 PRATT & WHITNEY CALIBRATION SERVICES LAB 17900 Beeline Highway MS 724-14 Jupiter, FL 33478 Contact: Mr. Jack Pardue Phone: 561 796 1315 CALIBRATION Valid To: January 31, 2019 Certificate Number: 2322.01 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations 1 : I. Electrical DC/Low Frequency Parameter/Equipment Range CMC 2, 3, 4 ( ) Comments DC Voltage Generate Up to 0.22 V (0.22 to 2.2) V (2.2 to 11) V (11 to 22) V (22 to 220) V (220 to 1100) V 7.5 µv/v + 0.4 µv 5.0 µv/v + 0.7 µv 3.5 µv/v + 2.5 µv 3.5 µv/v + 4 µv 5.0 µv/v + 40 µv 6.5 µv/v + 400 µv Fluke 5720A/5725A Fixed Point 10 V 2.0 µv/v (trend < 1.0 µv/v) Fluke 732A DC Voltage Measure (0 to 0.1) V (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V 6.0 µv/v + 1 µv 5.0 µv/v + 1 µv 5.0 µv/v + 2 µv 7.0 µv/v + 10 µv 17 µv/v + 100 µv HP 3458A/100 PLC option 002 DC Current Generate (0 to 220) µa 220 µa to 2.2 ma (2.2 to 22) ma (22 to 220) ma 220 ma to 2.2 A (2.2 to 11) A 40 µa/a + 6 na 35 µa/a + 7 na 35 µa/a + 40 na 45 µa/a + 0.7 µa 80 µa/a + 12 µa 0.036 % + 480 µa Fluke 5720A Fluke 5720A/5725A (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 1 of 12
Parameter/Equipment Range CMC 2, 3, 4, 5 ( ) Comments DC Current Measure (10 to 100) µa 100 µa to 1 ma (1 to 10) ma (10 to 100) ma 100 ma to 1.1 A 23 µa/a + 8 na 23 µa/a + 5 na 23 µa/a + 0.05 µa 38 µa/a + 0.5 µa 0.012 % + 10 µa HP 3458A option 002 Resistance Generate Fixed Points 0 Ω 1 Ω, 1.9 Ω 10 Ω, 19 Ω 100 Ω, 190 Ω 1 kω, 1.9 kω 10 kω, 19 kω 100 kω, 190 kω 1 MΩ 1.9 MΩ 10 MΩ 19 MΩ 100 MΩ 40 µω 95 µω/ω 23 µω/ω 10 µω/ω 8.5 µω/ω 8.5 µω/ω 11 µω/ω 20 µω/ω 21 µω/ω 40 µω/ω 47 µω/ω 0.01 % Fluke 5720A 0.001 Ω 0.01 Ω 0.1 Ω 50 µω/ω 50 µω/ω 0.02 % L&N 4223B L&N 4222B L&N 4221B 1 Ω, 10 Ω, 25 Ω 100 Ω, 1 kω 10 kω 10 MΩ 8 µω/ω 6 µω/ω 4 µω/ω 9 µω/ω Fluke 742A-1, -10, -25 Fluke 742A-100, -1K Fluke 742A-10K Fluke 742A-10M 100 MΩ, 1 GΩ 10 GΩ 100 GΩ 0.1 % 0.036 % 0.031 % HP 16340A RC Box k=3 Resistance Measure (0 to 10) Ω (10 to 100) Ω 100 Ω to 100 kω 100 kω to 1 MΩ (1 to 10) MΩ (10 to 100) MΩ 100 MΩ to 1 GΩ 19 µω/ω + 50 µω 16 µω/ω + 0.5 mω 14 µω/ω + 0.5 mω 19 µω/ω + 2.0 Ω 50 µω/ω + 20 Ω + 1000 Ω 5 MΩ/Ω + 10 kω HP 3458A option 002 (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 2 of 12
Parameter/Range Frequency CMC 2, 3, 4 ( ) Comments AC Current Generate (0 to 220) µa (1 to 5) khz (5 to 10) khz 0.025 % + 16 na 0.016 % + 10 na 0.012 % + 8 na 0.028 % + 12 na 0.11 % + 65 na Fluke 5720A 220 µa to 2.2 ma (1 to 5) khz (5 to 10) khz 0.025 % + 40 na 0.016 % + 35 na 0.012 % + 35 na 0.02 % + 220 na 0.11 % + 650 na (2.2 to 22) ma (1 to 5) khz (5 to 10) khz 0.025 % + 400 na 0.016 % + 350 na 0.012 % + 350 na 0.02 % + 550 na 0.11 % + 5 µa (22 to 220) ma (1 to 5) khz (5 to 10) khz 0.025 % + 4 µa 0.016 % + 3.5 µa 0.012 % + 2.5 µa 0.02 % + 3.5 µa 0.11 % + 10 µa 220 ma to 2.2 A 20 Hz to 1 khz (1 to 5) khz (5 to 10) khz 0.026 % + 35 µa 0.045 % + 80 µa 0.7 % + 160 µa (2.2 to 11) A (1 to 5) khz (5 to 10) khz 0.046 % + 170 µa 0.095 % + 380 µa 0.36 % + 750 µa Fluke 5720A/5725A AC Current Measure (0 to 100) µa (20 to 45) Hz 45 Hz to 1 khz 0.4 % + 0.03 % 0.15 % + 0.03 % 0.06 % + 0.03 % HP 3458A option 002 (1, 10, 100) ma (20 to 45) Hz 45 Hz to 1 khz 0.4 % + 0.03 % 0.15 % + 0.02 % 0.06 % + 0.02 % 100 ma to 1.05 A (20 to 45) Hz (45 to 100) Hz 100 Hz to 5 khz 0.4 % + 0.02 % 0.16 % + 0.02 % 0.08 % + 0.02 % 0.1 % + 0.02 % (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 3 of 12
Parameter/Range Frequency CMC 2, 3 ( ) Comments AC Voltage Generate (0 to 22) mv 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz 0.024 % + 4 µv 90 µv/v + 4 µv 80 µv/v + 4 µv 0.02 % + 4 µv + 5 µv 0.11 % + 10 µv 0.14 % + 20 µv 0.27 % + 20 µv Fluke 5720A (22 to 220) mv 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz 0.024 % + 12 µv 90 µv/v + 7 µv 80 µv/v + 7 µv 0.02 % + 7 µv 0.046 % + 17 µv 0.09 % + 10 µv 0.14 % + 20 µv 0.27 % + 20 µv 220 mv to 2.2 V 40 Hz to 20 khz 0.024 % + 40 µv 90 µv/v + 15 µv 45 µv/v + 8 µv 75 µv/v + 10 µv 0.011 % + 30 µv 0.042 % + 80 µv 220 mv to 2.2 V (300 to 500) khz 500 khz to 1 MHz 0.1 % + 200 µv 0.17 % + 300 µv (2.2 to 22) V 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz 0.022 % + 400 µv 90 µv/v + 150 µv 45 µv/v + 50 µv 75 µv/v + 100 µv 0.01 % + 200 µv 0.028 % + 600 µv 0.1 % + 200 µv 0.15 % + 300 µv (22 to 220) V 40 Hz to 20 khz (300 to 500) khz 500 khz to 1 MHz 0.024 % + 4 mv 90 µv/v + 1.5 mv 52 µv/v + 0.6 mv 80 µv/v + 1 mv 0.015 % + 2.5 mv 0.09 % + 16 mv 0.44 % + 40 mv 0.8 % + 80 mv (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 4 of 12
Parameter/Range Frequency CMC 2, 3, 4 ( ) Comments AC Voltage (cont.) Generate (0 to 250) V Max, Output 1100 V Range (15 to 50) Hz 50 Hz to 1 khz (1 to 20) khz 0.03 % + 16 mv 70 µv/v + 3.5 mv 90 µv/v + 4 mv 0.017 % + 6 mv 0.06 % + 11 mv Fluke 5720A/5725A (0 to 750) V (30 to 50) khz 0.06 % + 11 mv 0.23 % + 45 mv AC Voltage Measure (0 to 10) mv (1 to 40) Hz (1 to 20) khz 300 khz to 1 MHz (1 to 4) MHz (4 to 8) MHz 0.03 % + 0.03 % 0.02 % + 0.011 % 0.03 % + 0.011 % 0.1 % + 0.011 % 0.5 % + 0.011 % 4 % + 0.02 % 1.2 % + 7 % + 0.07 % 20 % + 0.08 % HP 3458A opt 002 10 mv to 10 V (1 to 40) Hz (1 to 20) khz 300 khz to 1 MHz (1 to 2) MHz (2 to 4) MHz (4 to 8) MHz (8 to 10) MHz 70 µv/v + 0.004 % 70 µv/v + 0.002 % 0.014 % + 0.002 % 0.03 % + 0.002 % 0.08 % + 0.002 % 0.3 % + 0.01 % 1 % + 0.01 % 1.5 % + 0.01 % 4 % + 0.07 % 4 % + 0.08 % 15 % + 0.1 % (10 to 100) V (1 to 40) Hz 40 Hz to 20 khz 300 khz to 1 MHz 0.02 % + 0.004 % 0.02 % + 0.002 % 0.035 % + 0.002 % 0.12 % + 0.002 % 0.4 % + 0.01 % 1.5 % + 0.01 % (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 5 of 12
Parameter/Range Frequency CMC 2, 3, 4 ( ) Comments AC Voltage (cont.) Measure (100 to 750) V (1 to 40) Hz 40 Hz to 1kHz (1 to 20) khz 0.04 % + 0.004 % 0.04 % + 0.002 % 0.06 % + 0.002 % 0.12 % + 0.002 % 0.30 % + 0.002 % HP 3458A option 002 AC Voltage Flatness Measure 2.2 mv 0.07 % + 1.0 µv 0.17 % + 1.0 µv 0.30 % + 1.0 µv 0.70 % + 2.0 µv Fluke 5790A option 03 7 mv 0.1 % 0.07 % + 1.0 µv + 1.0 µv 0.17 % + 1.0 µv 0.37 % + 1.0 µv 22 mv 0.07 % 0.17 % 0.37 % 70 mv 0.15 % 0.35 % (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 6 of 12
Parameter/Range Frequency CMC 2, 3 ( ) Comments AC Voltage Flatness Measure (cont) 220 mv 0.04 % 0.15 % 0.35 % Fluke 5790A opt 03 700 mv, 2.2 V, 7 V 0.03 % 0.15 % 0.35 % Up to 3 V 50 MHz 70 MHz 80 MHz 100 MHz 0.38 % 1.6 % 1.6 % 1.7 % By comparison to Ballantine model 1395D0.4, 1395D-1, 1395D-3 thermal voltage converters AC Voltage Flatness Generate 0.3 mv to 3.5 V (0.3 to 1.1) mv 0.3 % 0.1 % 0.2 % + 3 µv 0.4 % + 3 µv 0.6 % + 3 µv 1.5 % + 15 µv Fluke 5720A, option 5700A-03 (referenced to 1 khz) (0.3 to 3) mv 0.3 % + 3 µv 0.5 % + 3 µv 1.5 % + 3 µv 3 mv to 3.5 V 0.1 % + 1 µv 11 mv to 3.5 V 0.2 % + 3 µv 0.4 % + 3 µv 1 % + 3 µv (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 7 of 12
Parameter/Range Frequency CMC 2, 3 ( ) Comments Oscilloscopes Amplitude DC 50 Ω 1 MΩ (0 to ± 6.6) V (0 to ± 130) V 0.25 % + 40 µv + 40 µv Fluke 5520A w/ SC600 Amplitude, Square Ave (peak to peak) 50 Ω 1 MΩ ± 1 mv to ± 6.6 V 1 mv to ± 130 V 0.25 % + 40 µv 0.1 % + 40 µv Leveled Sine Wave 50 khz reference 2 % + 300 µv Amplitude@ 50 khz 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz 3.5 % + 300 µv 4 % + 300 µv 6 % + 300 µv Flatness@ 50 khz 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz 1.5 % + 100 µv 2 % + 100 µv 4 % + 100 µv Time Marker 5 s to 50 ms 20 ms to 2 ns (25 + 1000t) parts in 10 6 25 parts in 10 6 In the CMC, t is the time in seconds. Rise Time 300 ps 100 ps Phase Angle Generate 0.5 V/ 3 V 65 Hz 400 Hz 1 khz 10 khz 30 khz 1 khz 0.0 0.0 0.0 0.0 0.0 60, 90 0.1 0.25 0.5 5 10 0.5 Fluke 5520A/SC600 3 V/ 1 A / 65 Hz 0.0 0.1 3 V/ 5 A / 400 Hz 0.0, 60, 90 0.33 (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 8 of 12
Parameter/Equipment Range CMC 2, 3 ( ) Comments Capacitance Generate (0.33 to 11) nf (11 to 110) nf (110 to 330) nf (0.33 to 1.1) µf (1.1 to 3.3) µf (3.3 to 11) µf (11 to 33) µf (33 to 110) µf (110 to 330) µf (0.33 to 1.1) mf 0.5 % + 0.01 nf 0.25 % + 0.1 nf 0.25 % + 0.3 nf 0.25 % + 1 nf 0.35 % + 3 nf 0.35 % + 10 nf 0.4 % + 30 nf 0.5 % + 100 nf 0.7 % + 300 nf 1 % + 300 nf Fluke 5520A Electrical Simulation of Thermocouple Indicators Type E (-250 to -100) C (-100 to -25) C (-25 to 350) C (350 to 650) C (650 to 1000) C 0.5 C 0.16 C 0.14 C 0.16 C 0.21 C Fluke 5520A Type J (-210 to -100) C (-100 to -30) C (-30 to 150) C (150 to 760) C (760 to 1200) C 0.27 C 0.16 C 0.14 C 0.17 C 0.23 C Type K (-200 to -100) C (-100 to -25) C (-25 to 120) C (120 to 1000) C (1000 to 1372) C 0.33 C 0.18 C 0.16 C 0.26 C 0.4 C Type R (0 to 250) C (250 to 400) C (400 to 1000) C (1000 to 1767) C 0.57 C 0.35 C 0.33 C 0.4 C Type S (0 to 250) C (250 to 1000) C (1000 to 1400) C (1400 to 1767) C 0.47 C 0.36 C 0.37 C 0.46 C Type T (-250 to -150) C (-150 to 0) C (0 to 120) C (120 to 400) C 0.63 C 0.24 C 0.16 C 0.14 C (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 9 of 12
II. Fluid Quantities Parameter/Equipment Range CMC 2 ( ) Comments Flow Gas (10 to 30) slm 0.13 % of rdg or 0.013 % full scale (whichever is greater) DH Molbox-1 (Gn2, He, Arg) (30 to 100) slm 0.5 % of rdg or 0.13 % full scale (whichever is greater) (100 to 1000) slm 0.13 % of rdg Molbloc-S prem (0.005 to 0.5) lb/sec 0.5 % of rdg CFV calibration process (GN2, He) III. Mechanical Parameter/Equipment Range CMC 2 ( ) Comments Force Measure (100 to 1000) lbf 0.001 % full scale Morehouse 1K dead weight machine (1000 to 5000) lbf 0.01 % full scale Pratt & Whitney 5K dead weight machine (5000 to 10 000) lbf (10 000 to 100 000) lbf 0.013 % full scale 0.023 % full scale Comparison to Gold or Platinum load cells Mass (1 to 100) lb 140 µlb (61 mg) Sartorius CCE60K3 Pressure (Up to 25) psi (Up to 100) psi (Up to 1000) psi 0.0018 % rdg 0.0018 % rdg 0.0019 % rdg Ruska 2465 Pressure, Lox Clean Pres, XD's Gas (0 to 15) kpsia 0.015 % active range DH PPC2+, DH PPC3 Pressure, ODWT (6 to 2400) psi 0.0037 % rdg Ruska 2400 oil (2.4 to 12) kpsi (12.1 to 30) kpsi 0.0055 % rdg 0.03 % rdg or 0.3 psi (whichever is greater) DHI HGC-30000-AF (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 10 of 12
IV. Thermodynamic Parameter/Range Frequency CMC 2 ( ) Comments Temperature Measure 0 C 0.01 C Comparison with SPRT/triple point (0 to 1000) C (1000 to 1450) C 0.58 C 2.0 C Comparison with type T thermocouple Relative Humidity (10 to 90) % RH @ (-10 to 70) C 0.7 % RH Thunder Scientific 2500-LT V. Time & Frequency Parameter/Range Frequency CMC 2 ( ) Comments Frequency Measuring Equipment 100 khz, 1 MHz, 5 MHz 1 part in 10 10 Hz/ Hz HP model 105B quartz/symmetricom XL-GPS receiver Frequency Measure (0.05 to 500) MHz 1 part in 10 10 Hz/ Hz HP 5345A 1 This laboratory offers commercial calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 The measurands stated are generated with the Fluke 5720, 5790A and 5520 series of instruments. This capability is suitable for the calibration of the devices intended to measure the stated measurand in the ranges indicated. CMCs are expressed as either a specific value that covers the full range or as a fraction of the reading plus a fixed floor specification. 4 The measurands stated are measured with the HP 3458A. This capability is suitable for the calibration of the devices intended to generate the measurand in the ranges indicated. CMCs are expressed as either a specific value that covers the full range or as a combination of the fraction of the reading/output plus a range specification. (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 11 of 12
5 In the statement of CMC the percentages are percentages of reading, unless otherwise noted. (A2LA Cert. No. 2322.01) Revised 12/19/2018 Page 12 of 12
Accredited Laboratory A2LA has accredited PRATT & WHITNEY CALIBRATION SERVICES LAB West Palm Beach, FL for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSL Z540-1-1994 and R205 Specific Requirements: Calibration Laboratory Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 26 th day of October 2016. Senior Director, Accreditation Services For the Accreditation Council Certificate Number 2322.01 Valid to January 31, 2019 Revised December 19, 2018 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.