Mia + Drawer Chest Assembly Instructions - Please keep for future reference White 59586 Dimensions Width : Depth : Height: 88.5 cm. cm 90.0 cm Assembly Instructions - Please keep for future reference If you need help or have damaged or missing parts, call the Argos Customer Helpline: 085 60 0 0 507 Issue - 5-05-0
! Safety and re Advice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages and. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand or put weight on the product, this could cause damage. Assemble the item as close to its final position (in the same room) as possible. Assemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Dispose of all packaging carefully and responsibly. re and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels If you have damaged or missing components, call the Argos Customer Helpline: 085 60 0 0 Please check you have all the panels listed below Top (88,5 cm x, cm) 7 (76,7 cm x 7 cm) 8 Front rail (76,7 cm x 9,5 cm) x (88,5 cm x, cm) Side, left (8,6 cm x 8, cm) Side, right (8,6 cm x 8, cm) 9 Drawer front, small (7,9 cm x,5 cm) x 0 Drawer front, large (76, cm x,5 cm) x Drawer back, small (, cm x 9,8 cm) x Drawer side, right/left (5 cm x 9,8 cm) x Drawer bottom, small x (, cm x,7 cm) Drawer back, large x (7, cm x 9,8 cm) 5 Back x (8, cm x 9,5 cm) 6 H-Profile (80 cm x,7 cm) 5 Drawer bottom, large x (7, cm x,7 cm) 507-0
Components - ttings Please check you have all the panels listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. Ab Bp ø7.8 x 0mm Wooden dowel x 6 ø6 x 0mm Wooden dowel x ø x 5mm Screw x Di ø5 x 0.5mm m x 8 Fh ø5 x 8, ccmm Bolt x 8. x 5mm Nail x 5 Hk Back fitting w. ø.5 x 5mm Screw x M x 9mm Screw x Je Wall strap and instruction x ø x 5mm Screw x 6 ø.5 x mm Screw x ø5.8 x 8mm Screw x 8 ø5.8 x 9mm Screw x 6 ø, x 9,5mm Screw x 8 Vl ø0 x 9mm Spacer x 6 5 x 7 x 0mm Drawer runner x x x mm Angle x Wb Support for drawer runner x Tools required Phillips screwdriver (Medium & large) Hammer Flatblade screwdriver (Medium) Ruler - Use this ruler to help correctly identify the screws 0 0 0 0 0 50 60 70 80 90 00 0 0 0 0 50 60 70 507-0
Step Assembly of the chest. 6 5 5 7 8 Step. x the posts onto the sides and using screws into the holes indicated. The top of the posts and the sides and must be flush. ø x 5mm Screw x 6 Step. Knock the dowels into the holes indicated on the sides and using a small hammer. ø7.8 x 0mm Wooden dowel x ø5 x 8, ccmm Bolt x Screw the bolts into the holes indicated on the sides and. 507-05
Step. Slide the top of the drawer runners backwards. You can identify the front end of the drawer runner by the two M holes. See details. ø5.8 x 8mm Screw x 6 ø0 x 9mm Spacer x ø5.8 x 9mm Screw x 5 x 7 x 0mm Drawer runner x0 Place the Spacers as shown, and fix the front end of the upper drawer runners to the sides and using screws through the holes number and as indicated. Front end Hole no. Front end Hole no. x the front end of the rest of the drawer runners to the sides and using screws through the holes number and as indicated. Hole no. Hole no. See details. Hole no. Hole no. Hole no. Note the hole! Bottom end of right hand side Front end Hole no. 5 507-06
Step. Slide the top of the drawer runners forwards. Place the Spacers as shown, and fix the back end of the upper drawer runners to the sides and using screws through the holes indicated. ø5.8 x 8mm Screw x 8 ø5.8 x 9mm Screw x ø0 x 9mm Spacer x x the back end of the rest of the drawer runners to the sides and using screws through the holes indicated. See details. Step.5 Screw the bolts into the holes indicated on the top. ø5 x 8, ccmm Bolt x 507-07 6
Step.6 x the drawer runner supports Wb to the top using screws Je into the holes indicated. Je ø.5 x mm Screw x Wb Support for drawer runner x Je Wb Je Wb Je Je Wb Step.7 Slide the top of the drawer runners backwards. You can identify the front end of the drawer runner by the two M holes. ø5.8 x 8mm Screw x Front end 5 x 7 x 0mm Drawer runner x x the front end of the drawer runners to the drawer runner support Wb using screws through the holes number as indicated. Front end Hole no. Wb See details. Step.8 Slide the top of the drawer runners forwards. ø5.8 x 8mm Screw x x the drawer runners to the drawer runner support Wb using screws through the holes indicated. Wb See details. 7 507-08
Step.9 Knock the dowels into the holes indicated on the back rail 7 using a small hammer. ø7.8 x 0mm Wooden dowel x 7 Step.0 Vl x the angles Vl using screws into the holes indicated on the front rail 8. ø, x 9,5mm Screw x x x mm Angle x Vl Vl 8 Step. Place the sides and onto the back rail 7. ø5 x 0.5mm m x Push cams into the holes indicated on the back rail 7. Arrows pointing towards the sides /. Turn the cams to the right to fix the sides and. 7 507-09 8
Step. Place the top onto the sides and. Push cams into the holes indicated on the sides and. Arrows pointing towards the top. ø5 x 0.5mm m x Turn the cams to the right to fix the top. Step. Place the front rail 8 as shown. x the angles Vl to the sides using screws. See detail. ø, x 9,5mm Screw x 8 9 507-0
Step. Place the backs 5 into the rabbet on the top into the H-profile 6 and onto the posts. Distribute equally! Di. x 5mm Nail x Important!! Make sure the angle between the top and the posts is 90 when the backs 5 is attached. x the backs 5 to the top, the posts and the back rail 7 using nails Di. Di Di Di 5 5 Di 6 7 Use a small hammer. Step.5 Important!! The chest of drawers is heavy. Lift with care. Its recommended that the chest is fixed to the wall. Fh Wall strap and instruction x Use the fittings Fh. Follow the instructions included with the fittings. 507-0
Step Assembly of the drawers. 9 x 5 0 x Step. Bp x the drawer sides to the drawer backs and as shown, using screws Bp. Bp ø x 5mm Screw x Bp x Bp Bp x Step. Knock the dowels Ab into the holes indicated on the drawer sides using a smal hammer. Ab ø6 x 0mm Wooden dowel x Ab Ab x Ab Ab x 507-
Step. Slide the drawer bottoms and 5 into the drawer sides. x 5 x Step. Screw the bolts into the holes indicated on the drawer fronts 9 and 0. 9 x ø5 x 8, ccmm Bolt x 0 x Step.5 Push the drawer fronts 9 and 0 onto the drawer sides. 9 ø5 x 0.5mm m x Place cams into the holes indicated. Arrow pointing towards the front. Turn the cams to the right to fix the front. x 0 x 507-
Step.6 Important!! Make sure the angle between the drawer fronts 9 / 0 and the drawer sides is 90 before the drawer bottoms and 5 is fixed using as shown. x Back fitting w. ø.5 x 5mm Screw x 90 To adjust the angle between the drawer sides and the fronts push the fitting sidewards. See details. x Step.7 Pull out the drawer runners. Slide the drawers onto the runners. Hk M x 9mm Screw x t and fix the lower drawer first and work your way up. x drawers to the drawer runners using screws Hk. Hk Hk 507-