Scandi - 3 Door 5 Drawer Wardrobe Assembly Instructions - Please keep for future reference 02250 Dimensions Width : 0.9 cm Depth : 9.0 cm Height: 9.3 cm Assembly Instructions - Please keep for future reference 3502 MDF Issue - 22-0-20
! Safety and re Advice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages 3 and. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand or put weight on the product, this could cause damage. Assemble the item as close to its final position (in the same room) as possible. Assemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with 2 people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Dispose of all packaging carefully and responsibly. re and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE This product complies with BSEN9 Manufacturer: NJA Furniture A/S DK-00 Thisted Batch No: See label on the outside of the packing. te of manufacture: See label on the outside of the packing. If a glass component is chipped or broken, stop using the product and consult the manufacturer or supplier. Warning Do not place very hot or very cold items against or in close proximity to glass surfaces unless an adequately thick insulating matenal is used to prevent such items from coming into contact with the glass. Do not strike the glass with hard or pointed items. When cleaning glass panels use a damp cloth or leather with washing up liquid or 50ft soap if necessary; do not use washing powders or any other substances containing abrasives since these substances scratch glass. Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels Please check you have all the panels listed below 5 Top (,9 cm x,2 cm) 6 Bottom (,9 cm x,2 cm) Plinth, back x (,9 cm x 6 cm) 3 Divider (39,3 cm x,2 cm) 8 Plinth, front (9, cm x 9,6 cm) 9 Top rail (9 cm x 8 cm) Side, left (83,3 cm x,5 cm) 2 Side, right (83,3 cm x,5 cm) Divider, small x 3 (,5 cm x, cm) 0 Drawer front x 2 (59, cm x 5, cm) Drawerfront x 3 (39,5 cm x 5, cm) Drawer side, right/left (5 cm x 9,8 cm) x 0 3 Drawer back, small (35, cm x 9,8 cm) x 3 6 Drawer back x 2 (55 cm x 9,8 cm) Drawer bottom (56 cm x. cm) x 2 5 Drawer bottom x 3 (36, cm x, cm) Foot (9 cm x 5 cm) 9 2 20 Door, right Door, left (0,5 cm x 39,5 cm) (0,5 cm x 39,5 cm) Mirror door (0,5 cm x 39,5 cm) 2 Back x 3 (, cm x 39, cm) 8 H-Profile (38,5 cm x, cm) 22 Hanging rail (,2 cm x 2,2 cm) Please note!! The following packaging material, can be disposed after the product is assembled. 25 Waste (,5 cm x 9, cm) 23 Hanging rail (3,5 cm x 2,2 cm) 3502-03-MDF 2
Components - Fittings Please check you have all the panels listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. Ab Bb ø.8 x 0mm Wooden dowel x 20 ø6 x 30mm Wooden dowel x 20 ø x 60mm Screw x 3 Bo Bp ø3.5 x 5mm Screw x 3 ø3 x mm Screw x 6 ø3 x 35mm Screw x 20 ø5 x 0.5mm m x 2 Dg ø5 x, cc3mm Bolt x 2 Fh.2 x 20mm Nail x 00 Fi ø x 38mm Screw x Fl Back fitting w. ø3.5 x 5mm Screw x 0 Gc Support for hanger rail - 5mm x Wall strap and instruction x Hk Jc ø0 x 35mm Wooden Knob x 0 M x 9mm Screw x 0 Ke ø x 35mm Screw x 0 ø5.8 x 8mm Screw x 30 ø6. x.5mm Screw x 0 0mm Crossplate x 9 ø26mm Cup hinge x 9 Pc Pd Magnet, adjustable x 6 35 x x mm Magnet catch x 6 Va Vg Angle 20 x 20 x 6mm x 5 50 x 50 x 5mm Angle x 3 25 x x 0mm Drawer runner x0 Yd Nail holder x Tools required Phillips screwdriver (dium & large) Hammer Flatblade screwdriver (dium) Ruler - Use this ruler to help correctly identify the screws 0 0 20 30 0 50 60 0 80 90 00 0 0 30 0 50 60 0 3503-0 3502-0 MDF 3
Step Fix the drawer sides to the drawer backs 3 and as shown, using screws Bp. Bp x2 Bp 3 Bp Bp x3 Step 2 Knock the dowels Ab into the holes indicated on the drawer sides using a smal hammer. Ab x2 Ab Ab x3 Ab Step 3 Slide the drawer bottoms 5 and 6 into the drawer sides. x2 6 5 x3 Step Screw the bolts into the holes indicated on the drawer fronts 0 and. x2 0 x3 3503-05 3502-05
Step 5 Push the drawer fronts 0 and onto the drawer sides as shown. 0 Push cams into the holes indicated. Arrow pointing towards the front. Turn the cams to the right to fix the front 0 and. x2 x3 Step 6 Important!! Make sure the angle between the drawer fronts 0 / and the drawer sides is before the drawer bottoms 5 / 6 is fixed. 0 Fi x2 6 Fi Fi 5 Fi Fix the drawer bottoms 5 and 6 to the drawer backs 3 and and the drawer fronts 0 and using Fi. 3 x3 To adjust the angle between the drawer sides and the drawer fronts push the fitting Fi sidewards. See details. Fi Fi Fi Step Fix the wooden knobs Gc to the drawer fronts 0 and using screws Jc. Gc Jc Gc 0 Jc x2 Gc Jc x3 5 3503-06 3502-06
Step 8 Pc Knock the dowels into the holes indicated on the back plinths, the top 5 and the bottom 6 using a small hammer. x 6 Pc Pc Press the magnets Pc into the holes indicated on the top 5 and the bottom 6. Screw the bolts into the holes indicated on the top 5 and the bottom 6. 5 Pc Pc Step 9 Knock the dowels into the holes indicated on the divider 3. 3 Fix the Crossplates to the divider 3 and the sides and 2 using the pre-mounted screws. Note the details. Ke Position the Crossplates exactly as shown. Va Screw the bolts into the holes indicated on the sides and 2. Fix the angles Va to the sides and 2 using screws Ke. Place the angles as shown. See details. Va Ke 2 3503-0 3502-0 6
Step 0 Slide the top of the drawer runners backwards. Fix the front end of the drawer runners to the sides and 2 using screws through the holes indicated. See details. 2 Step Slide the top of the drawer runners forwards. Fix the back end of the drawer runners to the sides and 2 using screws through the holes indicated. See details. 3503-08 3502-08
Step Slide the top of the drawer runner backwards. Fix the front end of the drawer runners to the dividers using screws through the holes indicated. See details. Slide the top of the drawer runners forwards and fix the back end of the drawer runners to the dividers using screws through the hole indicated. See details. x 3 Step 3 Turn around the dividers. Fix the drawer runners to the dividers as shown. Same procedure as in step. x 3 Step Place the top 5 and the bottom 6 onto the divider 3. Push cams into the holes indicated. Arrows pointing towards the top 5 / bottom 6. Turn cams to the right to fix the top 5 and the bottom 6. Finally screw the bolts into the holes indicated on the bottom 6. 6 3 5 3503-09 3502-09 8
Step 5 Press the dividers onto the bottom 6. Push cams into the holes indicated on the dividers. Arrows pointing towards the bottom 6. 6 Turn cams to the right to fix the dividers. Step 6 Fix the plinths to the dividers using screws Dg. Screw the bolts into the holes indicated on the plinths. Dg Dg 9 3503-0 3502-0
Step Place the divider onto the plints. Push cams into the holes indicated on the divider. Arrows pointing towards the plinths. Turn the cams to the right to fix the divider. Step 8 Place the sides and 2 onto the top 5, the bottom 6 and the plinths. Push cams into the 5 5 holes indicated on the top 5, the bottom 6 and the plinths. Arrows pointing towards the sides and 2. Turn the cams to the right to fix the sides and 2. 2 6 3503-3502- 0
Step 9 Place the backs 2 into the rabbets in the sides and 2 and the H-profile 8. Yd 2 2 8 2 Important!! Make sure the angle between the top and the sides and 2 is when the backs 2 is attached. Bb Ke Fix the backs 2 using nails. Use the nail holder Yd and a small hammer. 2 Ke 8 Fix the front plinth 8 onto the angles Va using screws Ke. Ke Fix the back plinths onto the divider using screws Bb into the holes indicated. Va Ke Bb Step 20 Fix the foot to the back plinth using screw Bb. Bb 3503-3502-
Step 2 Place the top rail 9 onto the top 5. Vg 9 5 9 Fix the top rail 9 to the top 5 using angles Vg and screws. 9 Vg 5 Vg 9 3mm 5 Step 22! Warning! The wardrobe is heavy. Lift with care. Fh x Its recommended that the wardrobe is fixed to the wall. Use the fittings Fh. Follow the instructions included with the fittings. Wall strap and instruction Pull out the drawer runners. Slide the drawers onto the runners. Fix drawers to the drawer runners using screws Hk. Hk Hk 3502-3
Step 23 Place the cup hinges into the holes indicated on the doors 9, 20 and 2. Bo Pd Fix the hinges using screws. Fix the magnet catches Pd using screws Bo into the holes indicated. 2 Pd Bo Pd Bo 20 Bo Pd Bo Pd 9 Bo Pd 3 3502- MDF
Step 2 Fix the supports for hangerrails Fl onto the sides and 2 and the divider 3 using screws. Fl 3 Fl Fl 2 Fl Step 25 Place the hanger rail 22 and 23 into the supports Fl. 22 Fl 23 Slide the cup hinges onto the crossplates Fix the hinges using the premounted screw in the crossplates. See details below on how to fit the cup hinge onto the cross plate.! Gc 9 Jc 2 Jc Gc 20 Jc Gc! Fix the wooden knobs Gc to the doors using screws Jc. Tighten these screws Adjust the magnets Pc. Pc Pc 3502-5 MDF
Step 26 Adjusting the doors left/right. a: To adjust the door towards the left hand side - turn the adjusting screw to the right. a: b: b: To adjust the door towards the right hand side - turn the adjusting screw to the left. Adjusting the doors forwards/backwards. a: Loosen the fixing screw. b: Push the cup hinges / the door forwards OR backwards to adjust. c: Tighten the fixing screws of ALL the crossplates. a: b: c: 5 Adjusting the doors up/down. a: Loosen the two pre-mounted screws of each crossplate, BUT ONLY as much as it will allow the cross plate to move up and down. b: Push the the door up OR down to adjust. c: Tighten the pre-mounted screws of ALL the crossplates. a: b: c: 3502-6 MDF