Wiha Professional. Quality down to the last detail. Diagonal cutters and heavy duty diagonal cutters. Diagonal cutters and stripping pliers.

Wiha Professional. Quality down to the last detail. Diagonal cutters and heavy duty diagonal cutters. Diagonal cutters and stripping pliers. Z 12 0 05 Diagonal cutters Professional. Semi-circular, swedish style. Low wear lap joint, riveted and able to withstand high loads. The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. cutting edges. Long term cutting is achieved through additional inductive hardening to approx. 64 HRC. For soft and hard wires. 26736 140 5 ½ 4.0 2.5 1.8 1.4 160 5 27409 140 5 ½ 4.0 2.5 1.8 1.4 160 x 5 26740 160 6 ½ 4.0 2.8 2.0 1.6 200 5 27507 160 6 ½ 4.0 2.8 2.0 1.6 200 x 5 26743 180 7 4.0 3.0 2.5 1.8 250 5 27410 180 7 4.0 3.0 2.5 1.8 250 x 5 Z 18 0 05 BiCut Professional - switchable high-performance diagonal cutters. Standards: Based on DIN ISO 5749. Semi-circular. Clever - BiCut does the job of two pairs of pliers. Powerful - Up to 50% less hand strength required for cutting. Power - Cutting force doubled for extremely hard materials. Comfortable - Easily switch between the two strengths in a one handed operation. Robust and durable - Cutter blades induction hardened up to 64 HRC. Hard as steel - Drop forged of high-quality C70 steel. For cutting various materials from soft to extremely hard, such as cables, nails, screws, bolts, wire cable, spring wire, chains, etc. 38190 200 8 3.5 3 350 5 38983 200 8 3.5 3 350 x 5 Z 16 0 05 Heavy duty diagonal cutters Professional. Semi-circular. Low wear lap joint, riveted and able to withstand high levels of load. The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. cutting edges. Long term cutting is achieved through additional inductive hardening to approx. 64 HRC. High quality C 70 tool steel, specially tempered. Power assisted, all round diagonal cutter for soft wire as well as the most stringent of demands made by piano wires. 26747 160 6 ½ 3.5 2.5 2.0 190 5 27411 160 6 ½ 3.5 2.5 2.0 190 x 5 26750 180 7 3.8 2.7 2.3 260 5 27412 180 7 3.8 2.7 2.3 260 x 5 26753 200 8 4.2 3.0 2.5 315 5 27413 200 8 4.2 3.0 2.5 315 x 5 Z 55 0 05 Stripping pliers Professional. Standards: DIN ISO 5743. Precision cutting edge prism for even cutting of cable insulation. An easy to use adjusting screw allows the stripping diameter to be set. Opening spring for effortless and sensitive handling of pliers. Simple stripping of cables and strands of up to ø 5 mm/ 10 mm² conductor cross-section. 26846 160 6 ½ 5 10 155 5 27417 160 6 ½ 5 10 155 x 5 Details of cutting results of cutting pliers. Symbol/Types of wire Example Tensile strength ca. N/mm2 Soft wire Copper, aluminium 220-250 Medium hard wire Iron nail 750-800 Hard wire Spring wire, steel nails 1.600-1.800 Piano wire Hardened spring steel 2.200-2.300 Test wires standardised in DIN ISO 5744 266

Wiha Professional electric. Completely reliable. Diagonal cutters. Diagonal cutters. Z 12 0 06 Diagonal cutters Professional electric. Manufactured acc. to IEC 60900:2012. Semi-circular, swedish style. Low wear lap joint, riveted and able to withstand high loads. cutting edges. Long term cutting is achieved through additional inductive The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. Universal cutter for cutting soft and hard wires and cables, also suitable for cutting and stripping cables. For all work on or around electrical components up to 1,000 V AC. 26737 140 5 ½ 4.0 2.5 1.8 1.4 160 5 27428 140 5 ½ 4.0 2.5 1.8 1.4 160 x 5 26741 160 6 ½ 4.0 2.8 2.0 1.6 200 5 27429 160 6 ½ 4.0 2.8 2.0 1.6 200 x 5 26744 180 7 4.0 3.0 2.5 1.8 250 5 27430 180 7 4.0 3.0 2.5 1.8 250 x 5 Z 18 0 06 BiCut Professional electric - switchable high-performance diagonal cutters. Standards: Based on DIN ISO 5749. Semi-circular. Clever - BiCut does the job of two pairs of pliers. Powerful - Up to 50% less hand strength required for cutting. Power - Cutting force doubled for extremely hard materials. Comfortable - Easily switch between the two strengths in a one handed operation. Robust and durable - Cutter blades induction hardened up to 64 HRC. Hard as steel - Drop forged of high-quality C70 steel. For cutting various materials from soft to extremely hard, such as cables, nails, screws, bolts, wire cable, spring wire, chains, etc. For all work on or around electrical components up to 1,000 V AC. 38191 200 8 3.5 3 350 5 38984 200 8 3.5 3 350 x 5 Z 16 0 06 Heavy duty diagonal cutters Professional electric. Manufactured acc. to IEC 60900:2012. Semi-circular. Low wear lap joint, riveted and able to withstand high levels of load. cutting edges. Long term cutting is achieved through additional inductive The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. Power-assisted all-round diagonal cutter for cutting soft to extremely hard wires and cables. For all work on or around electrical components up to 1,000 V AC. 26748 160 6 ½ 3.5 2.5 2.0 190 5 27432 160 6 ½ 3.5 2.5 2.0 190 x 5 26751 180 7 3.8 2.7 2.3 260 5 27434 180 7 3.8 2.7 2.3 260 x 5 26754 200 8 4.2 3.0 2.5 315 5 27435 200 8 4.2 3.0 2.5 315 x 5 Z 14 0 06 Electrician's diagonal cutters Professional electric. Manufactured acc. to IEC 60900:2012. Semi-circular, swedish style. Low wear lap joint, riveted and able to withstand high loads. The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. Lightweight action, clean cutting achieved by specially milled precision cutting edges. Long term cutting is achieved through additional inductive Rear cutting area near to plier joint also suitable for medium-hard and hard wire. Front cutting area for soft wire, with precision stripping stations for 1.5 mm² and 2.5 mm² single-wire conductor. Special diagonal cutters with additional function for electrical installation. For all work on or around electrical components up to 1,000 V AC. 26745 160 6 ½ 4.0 2.0 1.6 200 5 27431 160 6 ½ 4.0 2.0 1.6 200 x 5 272

www.wiha.com Safety note: When working with cutting pliers beware of wire ends flying away. Please wear safety glasses. Installation pliers and cable cutter. Stripping pliers and needle-nose and round-nose pliers. Z 14 1 06 Professional electric TriCut installation pliers Standards: Manufactured acc. to IEC 60900:2012. With three processing stations: For cutting and stripping. Low wear lap joint, riveted and able to withstand high loads. Diagonal cutters with durable cutting edges due to additional induction Ergonomic and energy-saving stripping lengthwise on the cable and the pliers, thanks to the specially cranked head. Diagonal cutters for cutting soft and hard wires, as well as cables such as NYM lines 3x1.52-5x2.52 Flush stripping of round and damp-proof cable and stripping of conductors, even in hard-to-reach areas, e.g. in junction boxes and distribution boxes. For all work on or around electrical components up to 1,000 V AC. Z 55 0 06 Stripping pliers Professional electric. Standards: DIN ISO 5743. Manufactured acc. to IEC 60900:2012. Precision cutting edge prism for even cutting of cable insulation. An easy to use adjusting screw allows the stripping diameter to be set. Opening spring for effortless and sensitive handling of pliers. Simple stripping of cables and strands of up to ø 5 mm/ 10 mm² conductor cross-section. For all work on or around electrical components up to 1,000 V AC. 26847 160 6 ½ 5 10 155 5 27437 160 6 ½ 5 10 155 x 5 38552 170 7 4 2.5 1.6 260 5 38853 170 7 4 2.5 1.6 260 x 5 Z 07 0 06 Long-flat nose pliers Professional electric. Standards: DIN ISO 5745. Manufactured acc. to IEC 60900:2012. Extra long head. Ridged gripping surfaces. High-quality tool steel, tempered. Gripping and right-angled bending of wires and sheet metal parts. For all work on or around electrical components up to 1,000 V AC. 26732 160 6 ½ 160 5 27426 160 6 ½ 160 x 5 Z 50 1 06 Cable cutters Professional electric. Standards: Manufactured acc. to IEC 60900:2012. Classic cutting form. Light, energy-saving and clean cutting with specially ground precision cutting edges. Durable cutting edges due to additional induction hardening to approx. 58 HRC. Safety stop prevents finger injuries after cutting. Special tool steel C 70, tempered. Cable cutter for cutting of copper and aluminium cables without crushing, also suitable for stripping. Not for steel cable, wires and copper conductors with hard coatings. For all work on or around electrical components up to 1,000 V AC. 34743 160 6 ½ 16 50 190 5 35704 160 6 ½ 16 50 190 x 5 34744 200 8 20 60 305 5 35705 200 8 20 60 305 x 5 Z 09 0 06 Long-round nose pliers Professional electric. Standards: DIN ISO 5745. Manufactured acc. to IEC 60900:2012. Extra long head. Ridged gripping surfaces. High-quality tool steel, tempered. Gripping and bending of wires and sheet metal parts. For all work on or around electrical components up to 1,000 V AC. 26735 160 6 ½ 140 5 27427 160 6 ½ 140 x 5 273

Wiha Professional electric. Completely reliable. Cable shears. Cable shears. Z 71 1 06 Cable shears Professional electric. Lightweight standard model, straight. Standard model with wire stripper, cutting length 37 mm. Screw joint, adjustable cutting blades. Extruded plastic handle for a secure hold when cutting. C 50 carbon steel, hardened, nickel-plated. Universal cutter for electricians and other trades, also suitable for cutting and cutting back of cables. 27907 145 5 ¾ 95 5 Z 71 4 06 Electrician's / craftsman's cutters Professional electric. Sturdy model, straight, very robust, micro-toothed cutting. Precision model with wire stripper; cutting length 50 mm. Concealed, adjustable screw joint. Extruded handle made of impact-resistant plastic for powerful and safe cutting. High-alloy carbon steel, hardened, black finish. Highly-developed universal cutter for electricians and other trades, also suitable for cutting and stripping copper cables. 27910 145 5 ¾ 120 manganese-phosphated 5 Z 71 6 06 Electrician's / craftsman's cutters Professional electric. Strong, powerful design, straight, very robust, micro-ridged blade. Particularly comfortable two-component handle with soft zone in area subject to compressive stress. Cutting edge with wire cutter, cutting length 43 mm, cutting edge hardness approx. 56 HRC. Concealed, adjustable screw joint. Blades made of stainless steel, handles made of high-quality plastics. Qualitative, comfortable universal shears for electricians and many applications for trade and industry. Also suitable for cutting and cutting back of cables. 33910 145 5 ¾ 80 5 Z 71 5 06 Electrician's / craftsman's cutters Professional electric. Standard model, straight, micro-toothed blade. Particularly comfortable two-component handle with soft zone in area subject to compressive stress. Cutting edge with wire cutter, cutting length 34 mm. Concealed, adjustable screw joint. Blades made of stainless steel, handles made of high-quality plastics. Comfortable universal cutter for many applications in trade and industry, also suitable for cutting and stripping cables. 29420 145 5 ¾ 60 5 276

Wiha crimp tools and stripping tools. www.wiha.com Stripping tools. Crimping and stripping tool. 246 22 02 Cable stripper. Comfortable stripping with continuously adjustable cutting depth per adjusting screw and self-turning inner cutter. Damage to the inner conductor is therefore eliminated. Self-tensioning holding lever for safe cable guide. With cutter and hooked blade incl. safety cap for transport and storage. Additional spare blades included in the tool. Ergonomically designed construction. Impact resistant plastic housing made of Polyamide reinforced with glass-fibre. Hooked blade and cutter are made of hardened steel. Precise, fast and safe stripping of all common round cable from ø 4 mm 28 mm. Self-turning inner cutter for circular and longitudinal cutting. 35969 165 6 ½ 4.0-28 80 1 35538 165 6½ 4.0-28 80 x 1 246 78 SB Stripping knife for round cables. Blister packed. Standards: Manufactured acc. to IEC 60900:2012. Robust, fixed, sickle-shaped hooked blade. Shoe-shaped blade tip limits the cutting depth and prevents damage to conductors. Protective cap for safe transport and protection of cutting edges. Insulating multi-component handle. Blade of hardened, non-rusting steel. For stripping thick cables and cutting open the various layers of multiinsulated cables. For all work on or around electrical components up to 1,000 V AC. 36053 200 8 120 x 1 246 80 SB Cable stripping knife. Blister packed. Standards: Manufactured acc. to IEC 60900:2012. Rugged, fixed blade with straight cutting edge. Non-slip soft component in the handle ensures an optimal hold and more safety. Protective cap for safe transport and protection of cutting edges. Insulating multi-component handle. Blade of hardened, non-rusting steel. For stripping and cutting open of insulation, particularly large cables and the various layers of multi-insulated cables. For all work on or around electrical components up to 1,000 V AC. 246 77 SB Stripping tool for round cables. Blister packed. Double layered, folding stripping tool with opening spring and locking mechanism. Setting of cutting depth not required. Ergonomically designed tool body for non-slip, safe work. Housing of glass-fibre reinforced polyamide. Flush stripping of round and damp-proof cable from Ø 8 13 mm (e.g. NYM 3 x 1.5 mm² to 5 x 2.5 mm²), also for hard-to-reach locations e.g. ceiling and wall areas, in junction boxes, distribution boxes, switch cabinets etc. 36052 125 5 8-13 45 x 1 38798 200 8 120 x 1 246 76 SB Stripping tool for coaxial cables. Blister packed. Double layered, folding stripping tool with opening spring and locking mechanism. Setting of cutting depth not required. Extra-long tool body for optimal handling. With 5.0-20.0 mm length scale. Housing of glass-fibre reinforced polyamide. Incremental stripping of all commonly used coaxial cables (e.g. antenna and transmission cables) from 4.8 7.5 mm outer diameter. Also suitable for stripping of round cables (e.g. NYM 3 x 0.75 mm², PVC flex 10 mm² and 16mm²). 36051 110 4¼ 4.8-7.5 30 x 1 279

Wiha Industrial. Comfortable in your hand, versatile in application. Diagonal cutters and heavy duty diagonal cutters. Diagonal cutters and heavy-duty end cutting nippers. Z 12 0 02 Diagonal cutters Industrial. Semi-circular, swedish style. Low wear lap joint, riveted and able to withstand high loads. The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. cutting edges. Long term cutting is achieved through additional inductive hardening to approx. 64 HRC. For soft and hard wires. 30975 140 5 ½ 4.0 2.5 1.8 1.4 160 5 34311 140 5 ½ 4.0 2.5 1.8 1.4 160 x 5 30827 160 6 ½ 4.0 2.8 2.0 1.6 200 5 34516 160 6 ½ 4.0 2.8 2.0 1.6 200 x 5 30976 180 7 4.0 3.0 2.5 1.8 250 5 34571 180 7 4.0 3.0 2.5 1.8 250 x 5 Z 18 0 02 BiCut Industrial - switchable high-performance diagonal cutters. Standards: Based on DIN ISO 5749. Semi-circular. Clever - BiCut does the job of two pairs of pliers. Powerful - Up to 50% less hand strength required for cutting. Power - Cutting force doubled for extremely hard materials. Comfortable - Easily switch between the two strengths in a one handed operation. Robust and durable - Cutter blades induction hardened up to 64 HRC. Hard as steel - Drop forged of high-quality C70 steel. For cutting various materials from soft to extremely hard, such as cables, nails, screws, bolts, wire cable, spring wire, chains, etc. 38189 200 8 3.5 3 350 5 38982 200 8 3.5 3 350 x 5 Z 16 0 02 Heavy-duty diagonal cutters Industrial. Semi-circular. Low wear lap joint, riveted and able to withstand high levels of load. The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. cutting edges. Long term cutting is achieved through additional inductive hardening to approx. 64 HRC. Power assisted, all round diagonal cutter for soft wire as well as the most stringent of demands made by piano wires. 32333 160 6 ½ 3.5 2.5 2.0 190 5 34572 160 6 ½ 3.5 2.5 2.0 190 x 5 32339 180 7 3.8 2.7 2.3 260 5 34517 180 7 3.8 2.7 2.3 260 x 5 32341 200 8 4.2 3.0 2.5 315 5 34573 200 8 4.2 3.0 2.5 315 x 5 Z 17 0 02 Industrial heavy-duty end cutting nippers. Standards: DIN ISO 5748. Classic style. Low wear lap joint, riveted and able to withstand high levels of load. Striking high quality cutting edge with high cutting performance and low application of force due to highly precise processing. Good durability due to additional induction hardening of cutting edges to approx. 64 HRC. High-quality C 70 tool steel, hardened, polished and chrome-plated. Power assisted, all round diagonal cutter for soft wires as well as demanding piano wires. Also appropriate for binding (plaiting) and cutting wire netting in reinforced concrete structures. 36035 160 6 ½ 3.5 2.5 1.6 180 5 36982 160 6 ½ 3.5 2.5 1.6 180 x 5 36036 180 7 3.8 2.8 1.8 200 5 36983 180 7 3.8 2.8 1.8 200 x 5 36037 200 8 4.0 3.0 2.0 220 5 36984 200 8 4.0 3.0 2.0 220 x 5 282

www.wiha.com Safety note: When working with cutting pliers beware of wire ends flying away. Please wear safety glasses. Diagonal cutters and heavy duty diagonal cutters. Cable cutters. Z12009 Industrial electric diagonal cutters. Manufactured acc. to IEC 60900:2012. Semi-circular, swedish style. With multi-polished head. Low wear lap joint, riveted and able to withstand high loads. cutting edges. Long term cutting is achieved through additional inductive The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. Universal cutter for cutting soft and hard wires and cables, also suitable for cutting and stripping cables. For all work on or around electrical components up to 1,000 V AC. 38633 140 5 1/2 4 2.5 1.8 1.4 160 5 38860 140 51/2 4 2.5 1.8 1.4 160 x 5 33177 160 61/2 4 2.8 2 1.6 200 5 38861 160 61/2 4 2.8 2 1.6 200 x 5 Z 50 1 09 Industrial electric cable cutter. Standards: Manufactured acc. to IEC 60900:2012. Classic cutting form. With multi-polished head. Light, energy-saving and clean cutting with specially ground precision cutting edges. Durable cutting edges due to additional induction hardening to approx. 58 HRC. Safety stop prevents finger injuries after cutting. Special tool steel C 70, tempered. Cable cutter for cutting of copper and aluminium cables without crushing, also suitable for stripping. Not for steel cable, wires and copper conductors with hard coatings. For all work on or around electrical components up to 1,000 V AC. 38636 160 6 1/2 16 50 190 5 38865 160 6 1/2 16 50 190 x 5 35479 200 8 20 60 305 5 38866 200 8 20 60 305 x 5 Z16009 Industrial electric heavy-duty diagonal cutters. Manufactured acc. to IEC 60900:2012. Semi-circular. With multi-polished head. Low wear lap joint, riveted and able to withstand high levels of load. Lightweight action, clean cutting achieved by specially milled precision cutting edges. Long term cutting is achieved through additional inductive The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. High quality C 70 tool steel, specially tempered. Power-assisted all-round diagonal cutter for cutting soft to extremely hard wires and cables. For all work on or around electrical components up to 1,000 V AC. 38634 160 61/2 3.5 2.5 2 190 5 38862 160 61/2 3.5 2.5 2 190 x 5 38635 180 7 3.8 2.7 2.3 260 5 38863 180 7 3.8 2.7 2.3 260 x 5 35464 200 8 4.2 3 2.5 315 5 38864 200 8 4.2 3 2.5 315 x 5 Wiha Info Wiha DynamicJoint A new dimension in strength and durability Optimised joint construction Low loss of force means less force needed for cutting Optimal performance even after thousands of cuts Wiha Info Opti-Grip optimal grip due to newly designed gripping surfaces The 'triple-point support' protects the workpiece from twisting or slipping. Optimum grip even with a large jaw opening and at the same time significantly less force needed Now in standard Wiha combination pliers and high leverage combination pliers 287

www.wiha.com Safety note: When working with cutting pliers beware of wire ends flying away. Please wear safety glasses. Diagonal cutters and heavy duty diagonal cutters. Diagonal cutters and cable cutters. Z 12 0 01 Classic diagonal cutters. Semi-circular, swedish style. Low wear lap joint, riveted and able to withstand high loads. The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. cutting edges. Long term cutting is achieved through additional inductive hardening to approx. 64 HRC. For cutting of soft and hard wire. 26738 140 5 ½ 4.0 2.5 1.8 1.4 130 5 27346 140 5 ½ 4.0 2.5 1.8 1.4 130 x 5 26739 160 6 ½ 4.0 2.8 2.0 1.6 170 5 27347 160 6 ½ 4.0 2.8 2.0 1.6 170 x 5 26742 180 7 4.0 3.0 2.5 1.8 220 5 27348 180 7 4.0 3.0 2.5 1.8 220 x 5 Z 18 0 01 BiCut Classic - switchable high-performance diagonal cutters. Standards: Based on DIN ISO 5749. Semi-circular. Clever - BiCut does the job of two pairs of pliers. Powerful - Up to 50% less hand strength required for cutting. Power - Cutting force doubled for extremely hard materials. Comfortable - Easily switch between the two strengths in a one handed operation. Robust and durable - Cutter blades induction hardened up to 64 HRC. Hard as steel - Drop forged of high-quality C70 steel. For cutting various materials from soft to extremely hard, such as cables, nails, screws, bolts, wire cable, spring wire, chains, etc. 38060 200 8 3.5 3 310 5 38981 200 8 3.5 3 310 x 5 Z 16 0 01 Classic heavy-duty diagonal cutters. Semi-circular. Low wear lap joint, riveted and able to withstand high levels of load. The Wiha DynamicJoint ensures optimal transmission of hand strength to the cutting edges. cutting edges. Long term cutting is achieved through additional inductive hardening to approx. 64 HRC. High quality C 70 tool steel, specially tempered. Power-assisted all-round diagonal cutter for cutting soft to extremely hard wires and cables. Z 50 1 01 Classic cable cutter pliers. Classic cutting form. Light, energy-saving and clean cutting with specially ground precision cutting edges. Durable cutting edges due to additional induction hardening to approx. 58 HRC. Safety stop prevents finger injuries after cutting. High quality C 70 tool steel, tempered. Cable cutter for cutting of copper and aluminium cables without crushing, also suitable for stripping. Not for steel cable, wires and copper conductors with hard coatings. 34729 160 6 ½ 16 50 150 5 36217 160 6 ½ 16 50 150 x 5 34730 200 8 20 60 270 5 36981 200 8 20 60 270 x 5 26746 160 6 ½ 3.5 2.5 2.0 160 5 27349 160 6 ½ 3.5 2.5 2.0 160 x 5 26749 180 7 3.8 2.7 2.3 220 5 27370 180 7 3.8 2.7 2.3 220 x 5 26752 200 8 4.2 3.0 2.5 275 5 27371 200 8 4.2 3.0 2.5 275 x 5 Wiha Info Wiha BiCut - Double the power at the press of a button BiCut does the job of two pairs of pliers. Cutting force doubled for extremely hard materials. Up to 50% less hand strength required for cutting. 291

Wiha Classic. The complete workshop range. TriCut. Stripping pliers. Crimping pliers. Precision mechanic's needle-nose pliers. Z 14 1 01 Classic TriCut installation pliers. With three processing stations: For cutting and stripping. Low wear lap joint, riveted and able to withstand high loads. Diagonal cutters with durable cutting edges due to additional induction Ergonomic and energy-saving stripping lengthwise on the cable and the pliers, thanks to the specially cranked head. Two precision stripping stations for conductions with 1.5 mm2 and 2.5 mm2 High quality C 70 tool steel, tempered. Diagonal cutters for cutting soft and hard wires, as well as cables such as NYM lines 3x1.52-5x2.52 Flush stripping of round and damp-proof cable and stripping of conductors, even in hard-to-reach areas, e.g. in junction boxes and distribution boxes. Z 60 0 01 Classic crimping pliers. Standards: DIN ISO 5743. Fixed profile grooves for the relevant conductor cross-sections. Trapezoidal or semi-circular profiles for a secure connection between end sleeve and conductor. Sleeve and conductor inserted from the side. High-quality tool steel, tempered. For crimping end sleeves acc. to DIN 46228 parts 1 + 4. 28330 145 5 ¾ 0,25-2,5 130 5 30066 180 7 0,25-16 250 5 38627 170 7 4 2.5 1.6 230 5 38854 170 7 4 2.5 1.6 230 x 5 Z 55 0 01 Classic stripping pliers. Standards: DIN ISO 5743. Precision cutting edge prism for even cutting of cable insulation. An easy to use adjusting screw allows the stripping diameter to be set. Opening spring for effortless and sensitive handling of pliers. Simple stripping of cables and strands of up to ø 5 mm/ 10 mm² conductor cross-section. 26845 160 6 ½ 5 10 125 5 27368 160 6 ½ 5 10 125 x 5 Z 36 0 01 Precision mechanic's needle nose pliers with cutting edge and spring. Standards: DIN ISO 5745. Straight shape. Gripping surfaces partially serrated in parts. Cutting edges additionally induction hardened to approx. 64 HRC. With spring and opening limit for effortless, sensitive working. Grip and hold as well as cut soft and hard wires and cables, popular for precision mechanics and model-making applications. 36483 160 6½ 2 1.2 95 5 Details of cutting results of cutting pliers. Symbol/Types of wire Example Tensile strength ca. N/mm2 Soft wire Copper, aluminium 220-250 Medium hard wire Iron nail 750-800 Hard wire Spring wire, steel nails 1.600-1.800 Piano wire Hardened spring steel 2.200-2.300 Test wires standardised in DIN ISO 5744 292

www.wiha.com Safety note: When working with cutting pliers beware of wire ends flying away. Please wear safety glasses. Precision mechanic's diagonal cutters. Monier pliers (rabitz pliers). Z 44 3 01 Classic precision mechanic's diagonal cutters with spring. Semi-circular, swedish style. Low wear lap joint, riveted and able to withstand high loads. cutting edges. Long term cutting is achieved through additional inductive hardening to approx. 64 HRC. With spring and opening limit for effortless, sensitive working. For almost flush cutting of soft and semi-hard wires. Z 07 0 01 Classic long flat-nose pliers. Standards: DIN ISO 5745. Extra long head. Ridged gripping surfaces. High-quality tool steel, tempered. Gripping and right-angled bending of wires and sheet metal parts. 26730 160 6 ½ 130 5 27344 160 6 ½ 130 x 5 36189 125 5 2 0.8 65 5 Z 09 0 01 Classic long round-nose pliers. Standards: DIN ISO 5745. Extra long head. Ridged gripping surfaces. High-quality tool steel, tempered. Gripping and bending of wires and sheet metal parts. Z 15 0 01 Classic diagonal cutters for plastic. Standards: DIN ISO 5743. Semi-circular, swedish style. Low wear lap joint, riveted and able to withstand high loads. Precision cutting edge with surface-ground cutting surface and cutting edge without facet. For flush, clean cuts. Opening spring for effortless and sensitive handling of pliers. ideal for smooth cutting of plastic parts or soft materials. 37402 125 5 70 5 37403 160 6 ½ 165 5 26733 160 6 ½ 110 5 27345 160 6 ½ 110 x 5 Wiha Info Due to their moving component and their partly blank steel components, pliers require a certain amount of care: Therefore keep the pliers joints as clean as possible and lubricate them and the blank surfaces with a drop of thin, acidfree and resin-free oil: This ensures you can enjoy your Wiha quality pliers for a long time. 293

www.wiha.com Safety note: When working with cutting pliers beware of wire ends flying away. Please wear safety glasses. End cutting nippers and pincers. Monier pliers (rabitz pliers) Z 17 0 01 Classic heavy-duty end cutting nippers. Standards: DIN ISO 5748. Classic style. Low wear lap joint, riveted and able to withstand high levels of load. Striking high quality cutting edge with high cutting performance and low application of force due to highly precise processing. Good durability due to additional induction hardening of cutting edges to approx. 64 HRC. Power assisted, all round diagonal cutter for soft wires as well as demanding piano wires. Also appropriate for binding (plaiting) and cutting wire netting in reinforced concrete structures. 26757 160 6 ½ 3.5 2.5 1.6 180 5 27372 160 6 ½ 3.5 2.5 1.6 180 x 1 26758 180 7 3.8 2.8 1.8 200 5 27373 180 7 3.8 2.8 1.8 200 x 5 26759 200 8 4.0 3.0 2.0 220 5 27374 200 8 4.0 3.0 2.0 220 x 5 Z 31 0 01 Classic Monier pliers (rabitz pliers). Standards: DIN ISO 9242. Classic style. Low wear lap joint, riveted and able to withstand high levels of load. High quality cutting edge with high cutting performance and low application of force due to highly precise processing. Good durability due to additional induction hardening of cutting edges to approx. 64 HRC. For binding (plaiting) and cutting wire netting in reinforced concrete structures in a single operation. 26774 220 8 ¾ 3.2 2.0 1.6 360 5 27377 220 8 ¾ 3.2 2.0 1.6 360 x 5 26776 250 10 3.5 2.2 1.8 425 5 27378 250 10 3.5 2.2 1.8 425 x 5 26778 280 11 3.8 2.4 2.0 460 5 27379 280 11 3.8 2.4 2.0 460 x 5 26780 300 12 3.8 2.4 2.0 485 5 27380 300 12 3.8 2.4 2.0 485 x 5 Z 30 0 01 Classic pincers (grip, edge pliers). Standards: DIN ISO 9243. Classic style. Low wear lap joint, riveted and able to withstand high levels of load. Striking high quality cutting edge with high cutting performance and low application of force due to highly precise processing. Good durability due to additional induction hardening of cutting edges to approx. 64 HRC. For withdrawing and cutting nails and wire pins. 26771 180 7 2.0 265 5 27375 180 7 2.0 265 x 5 26772 200 8 2.2 350 5 27376 200 8 2.2 350 x 5 Z 31 0 00 Classic Monier pliers (rabitz pliers). Standards: DIN ISO 9242. Classic style. High quality cutting edge with high cutting performance and low application of force due to highly precise processing. Good durability due to additional induction hardening of cutting edges to approx. 64 HRC. For binding (plaiting) and cutting wire netting in reinforced concrete structures in a single operation. 26773 220 8 ¾ 3.2 2.0 1.6 350 5 27501 220 8 ¾ 3.2 2.0 1.6 350 x 5 26775 250 10 3.5 2.2 1.8 415 5 27502 250 10 3.5 2.2 1.8 410 x 5 26777 280 11 3.8 2.4 2.0 450 5 27503 280 11 3.8 2.4 2.0 450 x 5 26779 300 12 3.8 2.4 2.0 475 5 27504 300 12 3.8 2.4 2.0 475 x 5 295

www.wiha.com Safety note: When working with cutting pliers beware of wire ends flying away. Please wear safety glasses. Diagonal cutters, wide shape. Diagonal cutters, narrow shape. 10,0 8,0 Z 41 1 03 Diagonal cutters Electronic. 21 o 13,5 Wide, pointed head. Cutting edge with full flush cutter function. With opening spring. C 70 special tool steel. For an absolutely flush cut of soft wires in the electronics industry. 26818 138 5 ½ 1.3 70 5 27391 138 5 ½ 1.3 70 x 5 6,0 Z 40 0 03 Micro diagonal cutter Electronic. 21 o 9,5 Extra narrow, short head for working in particularly restricted spaces. Cutting edge with full flush cutter function. With opening spring. C 70 special tool steel. For absolutely flush cutting of soft wires in places which are difficult to access in the electronics industry. 26812 118 4 ½ 0.8 60 5 27388 118 4 ½ 0.8 60 x 5 4,0 10,0 8,0 Z 41 3 03 Diagonal cutters Electronic. 21 o 13,5 Standards: DIN ISO 9654. Wide, pointed head. Cutting edge with semi-flush cutter function, thus also appropriate for medium hard wires. Strong design for soft wires up to ø 2.0 mm. With opening spring. C 70 special tool steel. Cutting edges > 60 HRC. Universal small diagonal cutter for cutting soft and medium hard wires in the electronics and precision mechanical engineering industries. 26815 138 5 ½ 2.0 0.8 80 5 27393 138 5 ½ 2.0 0.8 80 x 5 6,0 Z 40 1 03 Diagonal cutters Electronic with wire trapping spring. 21 o 10,0 Narrow, pointed head. Cutting edge with full flush cutter function. With opening spring and fixture for collecting ends of wires that have been cut off. C 70 special tool steel. For absolutely flush cutting of soft wires in places which are difficult to access in the electronics industry. 26813 128 5 1.0 70 5 27390 128 5 1.0 70 x 5 5,0 Wiha Info Z 41 6 03 Diagonal cutters Electronic with wire trapping spring. 10,0 21 o 13,5 Wide, pointed head. Cutting edge with full flush cutter function. With opening spring and fixture for collecting ends of wires that have been cut off. C 70 special tool steel. Cutting edges approx. 56 HRC. For an absolutely flush cut of soft wires in the electronics industry. 26825 138 5 ½ 1.3 80 5 27395 138 5 ½ 1.3 80 x 5 6,0 Electronics pliers with cutting edges are designed especially for cutting soft to medium hard wires. The diameters of materials which your electronics pliers are able to cut depend not only on the material selected and the hardness of the cutting edges but also depend greatly on the geometry of the cutting edges: may cut off wires smoothly and flushly but are only appropriate for soft copper wires (99.85% pure copper) bevelled cutting edges function on the other hand may not cut in a totally flush manner but can cut thin iron wires or even medium hard steel wire results in the individual figures of pliers 303

Wiha Electronic. Precision for made-to-measure work. Diagonal cutters. Needle-nose pliers. Stripping pliers. 10,0 20,0 48 o 13,5 5,0 1,2 13,0 6,0 Z 46 0 03 Oblique cutting nippers Electronic. Wide, pointed head. Cutting edge with full flush cutter function. With cutting edge at 48 for cutting obliquely from above or from the side. C 70 special tool steel. For absolutely flush cutting of soft wires in places which are difficult to access in the electronics industry. 26833 138 5 ½ 1.3 70 5 27398 138 5 ½ 1.3 70 x 5 Z 36 0 03 Pointed pliers Electronic. Narrow, short head. With plain inside jaws. Width at tip is only 1.2 mm. C 70 special tool steel. For holding small components as well as for holding and angling wires. 26801 135 5 ½ 70 5 27326 135 5 ½ 70 x 5 10,0 3,5 40,0 30 o 4,0 28,9 Z 46 0 03 Micro oblique cutting nippers Electronic. Extremely narrow, short head for working in particullarly restricted spaces. Cutting edge with full flush cutter function. Edge at 30 to face end of pliers for cutting obliquely from above or from the side. C 70 special tool steel. For absolutely flush cutting of soft wires in places which are difficult to access in the electronics industry. 26830 118 4 ½ 0.6 60 5 27397 118 4 ½ 0.6 60 x 5 Z 49 2 03 Electronic stripping pliers. Wide, long head with ridged gripping surface, shears blade and firm wire stripping stations. Wire stripping stations: 0.8 / 1.0 / 1.3 / 1.6 / 2.0 / 2.6 mm, AWG 20 / 18 / 16 / 14 / 12 / 10. With opening spring and locking mechanism. C 70 special tool steel. For gripping, cutting and stripping of wires with diameter. 33471 180 7 0.8-2.6 20-10 70 5 36794 180 7 0.8-2.6 20-10 70 x 5 40,0 Wiha Info A variety of different pliers are required for electronics applications. Simply contact us if you require different models for other applications. Z 49 7 03 Electronic stripping pliers. 28,5 Wide, long head with ridged gripping surface, shears blade and firm wire stripping stations. Wire stripping stations: 0,4 / 0.5 / 0.6 / 0.8 / 1.0 / 1.3 mm, AWG 26 / 24 / 22 / 20 / 18 / 16. With opening spring and locking mechanism. C 70 special tool steel. For gripping, cutting and stripping of wires with diameter. 33472 180 7 0.4-1.3 26-16 70 5 35820 180 7 0.4-1.3 26-16 70 x 5 304

Wiha Professional ESD. Precise in every detail. www.wiha.com Hard, comfortable elastomer zones ensure low friction in the movement range of the fingers The anti-static, ergonomic handle is fixed to the pliers Double leaf spring for sensitive working Low glare mirror polished finish Wiha Professional ESD is ideal for electronics professionals needing precise, robust pliers. The formula for success for the pliers series is as simple as it is clever: uncompromising sharpness and hardness for flush cutting, and pleasant comfort with the handle for firm, fatigue-free grasping, holding and cutting. Precision box joint with long service life The Professional ESD diagonal cutter with a broad, pointed head cut soft wires flush. Antistatic arms made of soft, non-slip elastomer are gentle on the parts of the hand that are sensitive to pressure The Professional ESD needle-nose pliers are predominantly used for fine gripping and bending work. Suitable for work at ESD workstations in accordance with IEC 61340-5-1.Safety Notice: Wiha Professional ESD pliers are noninsulated, therefore not suitable for working on live parts. Wiha Professional ESD. ESD safe Suitable for work at ESD workstations in accordance with IEC 61340-5-1, surface resistance 10 6-10 9 ohms Anti-static Unique: all handle components are discharging (dissipative) Precise Box joint, resistant against twisting As hard as steel Pliers head drop forged from high quality steels Robust and durable Cutting edges are individually tempered and additionally induction hardened to approx. 64 HRC; joints are extremely wear resistant and withstand high stresses, with high-quality riveting Ergonomic Extra wide handle backs, with soft and hard zones perfectly distributed across the handle Attractive Appealing design with finely polished head 305

Wiha Professional ESD. Precise in every detail. Diagonal cutter, narrow, pointed shape. Diagonal cutter, broad, pointed shape. 10,5 13,5 9,5 11,5 Z 40 1 04 Diagonal cutter Professional ESD. Standards: DIN ISO 9654.IEC 61340-5-1. Narrow, pointed head. Bevelled cutting edges, individually tested, also appropriate for thin, hard wires. Maximum service life of cutting edge achieved through additional inductive High alloy carbon steel C 60. For cutting different hardnesses of wires in places which are difficult to access. 26808 115 4 ½ 1.0 0.6 0.3 60 5 27442 115 4 ½ 1.0 0.6 0.3 60 x 5 10,5 6,0 Z 41 1 04 Diagonal cutter Professional ESD. Wide, pointed head. Bevelled cutting edges, also appropriate for hard wires. High alloy carbon steel C 60. All round electronic diagonal cutter for cutting wires of different hardnesses. 26816 115 4 ½ 1.4 1.0 0.4 60 5 27444 115 4 ½ 1.4 1.0 0.4 60 x 5 13,5 7,5 9,5 11,5 Z 40 3 04 Diagonal cutter Professional ESD. Narrow, pointed head. Blade without facet, individually inspected, suited to thin, tough wire. High alloy carbon steel C 60. For absolutely flush cutting of copper wire in places which are difficult to access. 33521 115 4 ½ 1.0 60 5 10,5 6,0 Z 41 3 04 Diagonal cutter Professional ESD. Wide, pointed head. Cutting edge without bevel for absolute flush cutting. High alloy carbon steel C 60. For absolutely flush cutting of copper wire. 26821 115 4 ½ 1.0 60 5 27445 115 4 ½ 1.0 60 x 5 13,5 7,5 9,5 11,5 Z 40 4 04 Diagonal cutter Professional ESD. Extra narrow, short head for working in particularly restricted spaces. Cutting edge almost without bevel for virtually flush cutting, individually Maximum service life of cutting edge achieved through additional inductive High alloy carbon steel C 60. For virtually flush cutting copper wire in flat places which are difficult to access. 26814 115 4 ½ 1.0 60 5 27443 115 4 ½ 1.0 60 x 5 6,0 Z 41 4 04 Diagonal cutters Professional ESD with wire trapping spring. Wide, pointed head. With fixture for trapping ends of wires which have been cut off. Cutting edge with full flush cutter function for virtually flush cutting. High alloy carbon steel C 60. For virtually flush cutting copper wire, function for trapping cut off wire. 26822 115 4 ½ 1.2 60 5 27446 115 4 ½ 1.2 60 x 5 7,5 306

www.wiha.com Safety note: When working with cutting pliers beware of wire ends flying away. Please wear safety glasses. Diagonal cutter, semi-circular shape. Oblique end cutting nippers. 10,5 10,0 Z 43 1 04 Diagonal cutter Professional ESD. Narrow, semi-circular head. Cutting edge with full flush cutter function for virtually flush cutting. High alloy carbon steel C 60. For virtually flush cutting of copper wire in places which are difficult to access. 26826 115 4 ½ 1.2 60 5 27447 115 4 ½ 1.2 60 x 5 13,5 9,5 6,0 Z 46 1 04 Oblique end cutting nippers Professional ESD. 12,0 14,0 29o Wide head, angled at 29. Cutting edge with full flush cutter function for virtually flush cutting. High alloy carbon steel C 60. For virtually flush cutting of soft wires. Can be used horizontally and virtically. 26835 115 4 ½ 1.2 78 5 27450 115 4 ½ 1.2 78 x 5 20,0 7,5 11,5 40 o 6,3 10,0 Z 44 1 04 Diagonal cutter Professional ESD. Wide, semi-circular head. Bevelled cutting edges, also appropriate for thin, hard wires. High alloy carbon steel C 60. All round electronic diagonal cutter for cutting wires of different hardnesses. 26831 115 4 ½ 1.4 1.0 0.4 60 5 27448 115 4 ½ 1.4 1.0 0.4 60 x 5 13,5 7,5 Z 46 4 04 Oblique end cutting nippers Professional ESD. Extra narrow head. Cutting edges angled at 40. Cutting edge with full flush cutter function for virtually flush cutting. High alloy carbon steel C 60. For virtually flush cutting thin, soft wires in places which are particularly difficult to access. 26838 110 4 ¼ 0.6 42 5 27451 110 4 ¼ 0.6 42 x 5 5,8 11,5 Z 44 3 04 Diagonal cutter Professional ESD. Wide, semi-circular head. Cutting edge with full flush cutter function for virtually flush cutting. High alloy carbon steel C 60. For virtually flush cutting of soft wires. 26832 115 4 ½ 1.2 60 5 27449 115 4 ½ 1.2 60 x 5 7,5 307

Wiha Professional ESD. Precise in every detail. High leverage end cutting pliers. Needle nose pliers. 19,0 B 6,5 A Z 47 1 04 End cutting nippers Professional ESD. 2,8 5,8 Standards: DIN ISO 9654. IEC 61340-5-1. Extra narrow, slim shape. Cutting edge with full flush cutter function for virtually flush cutting. With opening spring. Surface resistance 10 6-10 9 ohms. High alloy carbon steel C 60. For virtually flush cutting of soft wires in places which are particularly difficult to access. 26839 110 4 ¼ 0.6 65 5 27452 110 4 ¼ 0.6 65 x 5 Z 36 0 04 Needle nose pliers Professional ESD. Standards: DIN ISO 9655. IEC 61340-5-1. Straight head. Fine, semi-circular tips. Ridged gripping surfaces. With opening spring. Surface resistance 10 6-10 9 ohms. C 45 special tool steel, hardened and tempered. Mainly for precision gripping and bending work. 26799 120 4 ¾ 9.5 23 6.5 1.4 60 5 27329 120 4 ¾ 9.5 23 6.5 1.4 60 x 5 27905 145 5 ¾ 12.0 40 7.5 2.0 93 5 F D 5,5 22,5 16,5 11,5 7,5 45 o 1,5 9,5 6,5 Z 47 2 04 End cutting nippers Professional ESD. Standards: DIN ISO 9654. IEC 61340-5-1. Wide head. Cutting edge with full flush cutter function for virtually flush cutting. With opening spring. Surface resistance 10 6-10 9 ohms. High alloy carbon steel C 60. For frontal, virtually flush cutting of thicker, soft wires. 26840 115 4 ½ 1.4 65 5 27453 115 4 ½ 1.4 65 x 5 Z 36 1 04 Needle nose pliers Professional ESD. Standards: DIN ISO 9655. IEC 61340-5-1. Angled at 45. Fine, semi-circular tips. Smooth gripping surfaces. With opening spring. Surface resistance 10 6-10 9 ohms. C 45 special tool steel, hardened and tempered. Mainly for precision gripping and bending work. 26802 120 4 ¾ 60 5 27439 120 4 ¾ 60 x 5 308

www.wiha.com Safety note: When working with cutting pliers beware of wire ends flying away. Please wear safety glasses. Round-nose and flat-nose pliers. Set combination. 20,5 9,5 2,0 6,5 Z 37 0 04 Round nose pliers Professional ESD. Standards: DIN ISO 9655. IEC 61340-5-1. Round, short jaws. Smooth gripping surfaces. With opening spring. Surface resistance 10 6-10 9 ohms. C 45 special tool steel, hardened and tempered. Mainly for precision gripping and bending work. 26804 120 4 ¾ 60 5 27440 120 4 ¾ 60 x 5 Z 99 0 001 04 Professional ESD pliers set, 4 pcs. Dissipative tools, electrostatically discharging. ESD tools manufactured according to IEC 61340-5-1. All pliers of high quality tool steel, hardened and fine-polished. Plier handles electrostatically discharge via all components. Surface resistance 10 6-10 9 ohms. Pouch: Light and space-saving storage of tools. Universal set for all cutting work with electronic applications. Z 38 0 04 Flat nose pliers Professional ESD. Standards: DIN ISO 9655. IEC 61340-5-1. Flat, short jaws. Smooth gripping surfaces. With opening spring. Surface resistance 10 6-10 9 ohms. C 45 special tool steel, hardened and tempered. Mainly for precision gripping and bending work. 14 3,5 22,5 9,5 6,5 Series 33507 Z 99 0 001 04 1 Z 41 3 04 Diagonal cutter Professional ESD. 115 mm 4 ½ " Z 44 1 04 Diagonal cutter Professional ESD. 115 mm 4 ½ " Z 46 4 04 Oblique end cutting nippers Professional ESD. 110 mm 4 ¼ " Z 36 0 04 Needle nose pliers Professional ESD. 120 mm 4 ¾ " 26806 120 4 ¾ 60 5 27441 120 4 ¾ 60 x 5 Wiha Info A number of different pliers are required for electronics. Please ask us if you would like other pliers models for further applications. 309