Surface Mount Voltage Controlled Oscillator Wide Band 612 to 1200 MHz Features very wide band, 612 to 1200 MHz linear tuning sensitivity, 26-68 MHz/V typ. low phase noise, -139 dbc/hz at 1 MHz offset, typ. aqueous washable Applications cellular test equipment CASE STYLE: CK605 +RoHS Compliant The +Suffix identifies RoHS Compliance. See our web site for RoHS Compliance methodologies and qualifications FREQUENCY (MHz) POWER OUTPUT (dbm) TUNING VOLTAGE (V) Min. Max. Typ. Min. Max. 1 khz PHASE NOISE (dbc/hz) SSB at offset frequencies: Typ. 10 khz 100 khz Electrical Specifications PULLING pk-pk @ 12 dbr (MHz) PUSHING TUNING SENSITIVITY HARMONICS (dbc) 3 db MODULATION BANDWIDTH (MHz) 1 MHz Typ. Typ. Typ. Typ. Max. Typ. DC OPERATING POWER 612 1200 10.0 0.5 18-71 -97-119 -139 9.0 0.45 26-68 -18-10 20 12 40 Vcc (volts) Current (ma) Max. Pin Connections RF OUT 10 VCC 14 V-TUNE 2 GROUND 1,3,4,5,6,7,8,9,11,12,13,15,16 Outline Drawing PCB Land Pattern Maximum Ratings Operating Temperature -55 C to 85 C Storage Temperature -55 C to 100 C Absolute Max. Supply Voltage (Vcc) +15V Absolute Max. Tuning Voltage (Vtune) +25V all specifications: 50 ohm system Permanent damage may occur if any of these limits are exceeded. Demo Board MCL P/N: TB-10 Suggested PCB Layout (PL-012) Suggested Layout, Tolerance to be within±.002 Outline Dimensions ( inch mm ) A B C D E F G H J K L M N P Q R S T wt..500.500.180.100.080.115.060.040.540.060.100.135.135.115.140.070.150.070 grams 12.70 12.70 4.57 2.54 2.03 2.92 1.52 1.02 13.72 1.52 2.54 3.43 3.43 2.92 3.56 1.78 3.81 1.78 1.0 Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, Standard Terms ); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits website at www.minicircuits.com/mclstore/terms.jsp Mini-Circuits www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com REV. F M151108 EDR-4758 RAV/MCL 151105 Page 1 of 2
Performance Data & Curves V TUNE TUNING SENS. FREQUENCY (MHz) POWER OUTPUT (dbm) -55 C +25 C +85 C -55 C +25 C +85 C Frequency (MHz) 1500 1200 900 600 300 0 Frequency and Tuning Sensitivity (at +25 C) -55 C +25 C +85 C T SENS. 0 3 6 9 12 15 18 150 120 90 60 30 0 Tuning Sensitivity 1.00 47.12 598.64 582.01 569.22 12.91 11.06 12.48 2.00 37.64 636.03 619.65 607.12 12.82 11.26 11.93 3.00 34.64 670.50 654.29 641.99 13.06 11.01 12.04 4.00 33.78 704.46 688.07 675.30 13.14 11.14 12.25 5.00 34.25 739.39 722.33 709.75 12.77 10.99 12.30 6.00 36.07 775.44 758.40 745.61 12.52 10.78 11.76 7.00 38.84 815.21 797.24 783.95 12.44 10.86 11.45 8.00 43.70 859.59 840.94 827.33 12.81 10.64 11.30 9.00 47.04 907.79 887.98 873.63 12.50 10.81 11.79 10.00 48.70 957.54 936.68 922.09 12.42 10.73 11.15 11.00 48.29 1006.88 984.96 969.49 12.39 10.63 10.93 12.00 45.74 1052.66 1030.70 1015.18 12.83 10.55 11.06 13.00 41.80 1094.91 1072.50 1056.86 12.22 10.61 11.30 14.00 38.36 1133.33 1110.86 1095.63 11.93 10.38 10.65 15.00 35.82 1168.29 1146.68 1131.71 11.77 10.30 10.25 16.00 33.41 1200.85 1180.09 1165.90 11.96 10.10 10.05 17.00 31.77 1231.20 1211.87 1198.68 11.74 9.84 10.06 18.00 30.13 1259.63 1241.99 1229.94 11.30 9.48 9.60 Output Power (dbm) 14 13 12 11 10 9 Power Output -55 C +25 C +85 C 0 3 6 9 12 15 18 V TUNE HARMONICS (dbc) F2 F3 F4 FREQ. PUSHING Harmonics (dbc) 0-10 -20-30 -40-50 -60 Harmonics Level F2 F3 F4 0 3 6 9 12 15 18 1.00-19.95-24.48-37.49 0.66 2.00-20.83-24.55-36.94 0.56 3.00-21.93-24.41-37.55 0.50 4.00-22.85-24.11-38.30 0.46 5.00-23.97-23.81-40.38 0.42 6.00-25.35-23.56-44.83 0.38 7.00-26.54-23.45-49.80 0.34 8.00-28.01-23.68-50.47 0.37 9.00-29.97-23.61-49.48 0.39 10.00-32.61-24.70-47.25 0.43 11.00-35.58-26.24-45.26 0.46 12.00-36.67-30.11-44.19 0.46 13.00-35.63-34.11-44.53 0.46 14.00-34.37-37.14-45.92 0.46 15.00-32.82-37.55-46.61 0.43 16.00-31.07-38.22-49.81 0.43 17.00-29.62-38.30-47.23 0.38 18.00-28.42-39.50-48.55 0.33 Pushing 1.0 0.8 0.6 0.4 0.2 0.0 Frequency Pushing (Supply Voltage 12V) 0 3 6 9 12 15 18 Notes A. Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document. B. Electrical specifications and performance data contained in this specification document are based on Mini-Circuit s applicable established test performance criteria and measurement instructions. C. The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, Standard Terms ); Purchasers of this part are entitled to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits website at www.minicircuits.com/mclstore/terms.jsp Mini-Circuits www.minicircuits.com P.O. Box 350166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com Page 2 of 2
Voltage Controlled Oscillator Typical Performance Data V TUNE FREQUENCY POWER OUTPUT HARMONICS FREQ. FREQ PHASE TUNE SENS (MHz) (dbm) (dbc) PUSH OFFSET NOISE (KHz) (dbc/hz) -55ºC +25ºC +85ºC -55ºC +25ºC +85ºC F2 F3 F4 1.0 47.12 598.6 582.0 569.2 12.91 11.06 12.48-20.0-24.5-37.5 0.66 1-71 2.0 37.64 636.0 619.7 607.1 12.82 11.26 11.93-20.8-24.6-36.9 0.56 10-97 3.0 34.64 670.5 654.3 642.0 13.06 11.01 12.04-21.9-24.4-37.6 0.50 100-119 4.0 33.78 704.5 688.1 675.3 13.14 11.14 12.25-22.9-24.1-38.3 0.46 1000-139 5.0 34.25 739.4 722.3 709.7 12.77 10.99 12.30-24.0-23.8-40.4 0.42 6.0 36.07 775.4 758.4 745.6 12.52 10.78 11.76-25.4-23.6-44.8 0.38 7.0 38.84 815.2 797.2 784.0 12.44 10.86 11.45-26.5-23.5-49.8 0.34 8.0 43.70 859.6 840.9 827.3 12.81 10.64 11.30-28.0-23.7-50.5 0.37 9.0 47.04 907.8 888.0 873.6 12.50 10.81 11.79-30.0-23.6-49.5 0.39 10.0 48.70 957.5 936.7 922.1 12.42 10.73 11.15-32.6-24.7-47.3 0.43 11.0 48.29 1006.9 985.0 969.5 12.39 10.63 10.93-35.6-26.2-45.3 0.46 12.0 45.74 1052.7 1030.7 1015.2 12.83 10.55 11.06-36.7-30.1-44.2 0.46 13.0 41.80 1094.9 1072.5 1056.9 12.22 10.61 11.30-35.6-34.1-44.5 0.46 14.0 38.36 1133.3 1110.9 1095.6 11.93 10.38 10.65-34.4-37.1-45.9 0.46 15.0 35.82 1168.3 1146.7 1131.7 11.77 10.30 10.25-32.8-37.6-46.6 0.43 16.0 33.41 1200.9 1180.1 1165.9 11.96 10.10 10.05-31.1-38.2-49.8 0.43 17.0 31.77 1231.2 1211.9 1198.7 11.74 9.84 10.06-29.6-38.3-47.2 0.38 18.0 30.13 1259.6 1242.0 1229.9 11.30 9.48 9.60-28.4-39.5-48.6 0.33 REV. X1 070205 Page 1 of 1
Voltage Controlled Oscillator Typical Performance Data Frequency and Tuning Sensitivity Power Output Frequency (MHz) 1400 1300 1200 1100 1000 900 800 700 600 FREQ. @ -55 C FREQ. @ +25 C FREQ. @ +85 C T.SENS @ +25 C 70 65 60 55 50 45 40 35 30 Tuning Sensitivity Output Power (dbm) 22 20 18 16 14 12 10 8 6-55 C +25 C +85 C 500 25 4 400 20 0 2 4 6 8 10 12 14 16 18 2 0 2 4 6 8 10 12 14 16 18 Harmonics Level Frequency Pushing 0 0.70-10 0.65 Pushing @ +25 C -20 0.60 Harmonics (dbc) -30-40 -50-60 Pushing 0.55 0.50 0.45 0.40-70 -80-90 F2 @ +25 C F3 @ +25 C F4 @ +25 C 0.35 0.30 0.25-100 0 2 4 6 8 10 12 14 16 18 0.20 0 2 4 6 8 10 12 14 16 18-50 -60 Phase Noise Phase Noise @ +25 C Phase Noise (dbc/hz) -70-80 -90-100 -110-120 -130-140 -150 1 10 100 1000 Frequency Offset (khz) REV. X1 070205 Page 1 of 1
Case Style Outline Dimensions PCB Land Pattern CK CK605 Suggested Layout, Tolerance to be within.002 CASE # A B C D E F G H J K.500.500.180.100.080.115.060.040.540.060 CK605 (12.70) (12.70) (4.57) (2.54) (2.03) (2.92) (1.52) (1.02) (13.72) (1.52) CASE # L M N P Q R S T WT. GRAM.100.135.135.115.140.070.150.070 CK605 1.0 (2.54) (3.43) (3.43) (2.92) (3.56) (1.78) (3.81) (1.78) Dimensions are in inches (mm). Tolerances: 2 Pl. +.03; 3Pl..015 Notes: 1. Case material: Nickel-Silver alloy. 2. Base: Printed wiring laminate. 3. Termination finish: For RoHS Case Styles: 3-5 µ inch (.08-.13 microns) Gold over 120-240 µ inch (3.05-6.10 microns) Nickel plate. All models, (+) suffix. 98-CK Rev.: W (10/17/17) M163961 File: 98-CK Sheet 1 of 13 This document and its contents are the property of Mini-Circuits
Tape & Reel Packaging TR-F37 Tape Width, mm Device Cavity Pitch, mm 24 16 Reel Size, inches 7 Devices per Reel Small quantity standards (see note) 13 Standard 10 20 50 100 200 500 Note: Please consult individual model data sheet to determine device per reel availability. Mini-Circuits carrier tape materials provide protection from ESD (Electro-Static Discharge) during handling and transportation. Tapes are static dissipative and comply with industry standards EIA-481/EIA-541. Go to: www.minicircuits.com/pages/pdfs/tape.pdf 98-TR-F37 Rev.: C (01/17/18) M164706 File: 98-TR-F37.docx Sheet 1 of 1 This document and its contents are the property of Mini-Circuits.
Mini-Circuits Environmental Specifications ENV65 All Mini-Circuits products are manufactured under exacting quality assurance and control standards, and are capable of meeting published specifications after being subjected to any or all of the following physical and environmental test. Specification Test/Inspection Condition Reference/Spec Operating Temperature -55 to 85 C Ambient Environment Individual Model Data Sheet Storage Temperature -55 to 100 C Ambient Environment Individual Model Data Sheet Humidity 90 to 95% RH, 240 hours, 50 C MIL-STD-202, Method 103, Condition A, Except 50 C and end-point electrical test done within 12 hours Thermal Shock -55 to 100 C, 100 cycles MIL-STD-202, Method 107, Condition A-3, except +100 C Solder Reflow Heat Sn-Pb Eutectic Process: 225 C peak Pb-Free Process, 245 C peak J-STD-020, Table 4-1, 4-2 and 5-2, Figure 5-1 Solderability 10X Magnification J-STD-002, Para 4.2.5, Test S, 95% Coverage Vibration (High Frequency) 20g peak, 20-2000 Hz, 4 times in each of three axes (total 12) MIL-STD-883, Method 2007.3, Condition A Mechanical Shock 50g, 11 ms, 1/2-sine, 18 shocks: 3 each direction, each of 3 axes MIL-STD-202, Method 213, Condition A Marking Resistance to Solvents Isopropyl alcohol + mineral spirits at 25 C; terpene defluxer at 25 C; distilled water + proylene glycol monomethyl ether + monoethanolamine at 63 C to 70 C MIL-STD-202, Method 215 ENV65 Rev: OR 03/20/12 M136382 File: ENV65.pdf This document and its contents are the property of Mini-Circuits. Page: 1