DRG-Series. Digital Radio Gateway. Hytera DMR USB Donor (Tier-2) Digital Radio Supplement

Similar documents
DRG-Series. Digital Radio Gateway. Tait P25 CCDI Tier-2 (TM9400 Series Mobile Radio) Digital Radio Supplement

DRG-Series. Digital Radio Gateway. Motorola MotoTRBO DMR. Interfacing Omnitronics DRG with Motorola MotoTRBO DMR Digital Radios

DRG-Series. Digital Radio Gateway. Kenwood NXDN Donor Radio (Tier-2) Interfacing Omnitronics DRG with Kenwood NXDN Donor Digital Radios (Tier-2)

DRG-Series. Digital Radio Gateway. Icom IDAS Conventional Wireline IP (Tier-2) (IC-FR5000/IC-FR6000 IDAS VHF/UHF Repeaters) Digital Radio Supplement

DRG-Series. Digital Radio Gateway. Icom IDAS MultiTrunk IP (Tier-3) Digital Radio Supplement

DX-Altus Reaching new Heights in Radio Dispatch & Interoperability for Mission Critical Communications

DX-Altus. Reaching New Heights in Radio Dispatch & Interoperability

"Terminal RG-1000" Customer Programming Software. User Guide. August 2016 R4.3

Hytera DMR Conventional Series

Configuration Guide. Version 8.3

TRBOnet Mobile. User Guide. for Android. Version 2.0. Internet. US Office Neocom Software Jog Road, Suite 202 Delray Beach, FL 33446, USA

TRBOnet Mobile. User Guide. for ios. Version 1.8. Internet. US Office Neocom Software Jog Road, Suite 202 Delray Beach, FL 33446, USA

TRBOnet Enterprise. Capacity Plus. Deployment Guide. Internet. US Office Neocom Software Jog Road, Suite 202 Delray Beach, FL 33446, USA

TRBOnet Enterprise. Linked Capacity Plus. Deployment Guide. Internet. US Office Neocom Software Jog Road, Suite 202 Delray Beach, FL 33446, USA

Challenging Communication Boundaries. RoIP Gateways. Radio over IP for Optimal Analog & Digital Radio Network Performance

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. October 2017 R2.0

SpeedTouch 190. Setup and User s Guide. SIP Gateway. Release R1.0

TRBOnet Enterprise. IP Site Connect. Deployment Guide. Internet. US Office Neocom Software Jog Road, Suite 202 Delray Beach, FL 33446, USA

TRBOnet Enterprise. Extended Range Direct Mode. Deployment Guide. Internet

Version 8.8 Linked Capacity Plus. Configuration Guide

Version 9.1 SmartPTT Enterprise. Installation & Configuration Guide

Version 9.1 SmartPTT Monitoring

Version SmartPTT Enterprise. Installation and Configuration Guide

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. June 2018 R2.2.2 v2

Version 9.2. SmartPTT PLUS. Capacity Max Configuration Guide

XPT Digital Trunking Decentralized and Cost-Effective Digital Trunking Solution

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. March 2018 R2.2.1

TurboVUi Solo. User Guide. For Version 6 Software Document # S Please check the accompanying CD for a newer version of this document

Quick Start Guide. RSP-Z2 Dual Channel Analog-IP Interface

Which Dispatch Solution?

Version 9.1. Installation & Configuration Guide

Hytera. PD41X Patrol Management System. Installation and Configuration Guide

DX64. Digital Audio and Radio Management System RADIO DISPATCH SWITCH FOR MISSION CRITICAL NETWORKS

Challenging Communication Boundaries. 950 Radio. Management System Series II

OPERATING GUIDE OPERATING GUIDE FOR IC-F5060/F6060 SERIES BIIS 1200/MDC 1200 SYSTEM/ LTR /IDAS NXDN OPERATION

MOTOTRBO R1.8 Training Overview

Managing Radios and Radio Descriptors

OPERATING GUIDE OPERATING GUIDE FOR IC-F3160/F4160 SERIES BIIS 1200/MDC 1200 SYSTEM/ LTR /IDAS OPERATION

PaperCut VCA Cash Acceptor Manual

IP/Console

OPERATING GUIDE OPERATING GUIDE FOR IC-F5060/F6060 SERIES BIIS 1200/MDC 1200 SYSTEM/ LTR /IDAS OPERATION

Networks of any size and topology. System infrastructure monitoring and control. Bridging for different radio networks

Understanding PMC Interactions and Supported Features

SIP Trunking Service Configuration Guide for XO

SafeMobile Radio Configuration

Hytera Smart Dispatch

XLR PRO Radio Frequency (RF) Modem. Getting Started Guide

101 Overview Presentation

OPERATING GUIDE OPERATING GUIDE FOR IC-F3160/F4160 SERIES BIIS 1200/MDC 1200 SYSTEM/ LTR /IDAS NXDN OPERATION

Hytera DMR Conventional Series Release Notes

Blue Bamboo P25 Device Manager Guide

AP-SRD100 Smart RoIP(Radio over IP) Dispatcher

Kodiak Corporate Administration Tool

NEXEDGE Type-D Trunking System

LincView OPC USER GUIDE. Enhanced Diagnostics Utility INDUSTRIAL DATA COMMUNICATIONS

CTI Products. RadioPro IP Gateway. Installation Guide. Document # S For Version 8 Software

TRBOnet Enterprise/PLUS

TRBOnet Guard Tour Configuration and Operation Guide

DMR Radio Authorization Operation Guide

TRBOnet Enterprise 2.6 for MOTOTRBO Capacity Plus.

Radio Bridge User Guide. Document: DOC-VS-RB-UG-C-0

F8101ALE User s Guide

Challenging Communication Boundaries. Ser i es I I

JEM Radio II Operation Guide. Manual P/N M Victor Place Colorado Springs, Colorado

UCP-Config Program Version: 3.28 HG A

OPERATING GUIDE OPERATING GUIDE FOR IC-F3210D/F4210D/F3230D/ F4230D/F5220D/F6220D SERIES IDAS NXDN OPERATION

WCS-D5100 Programming Software for the Icom ID-5100 Data

Networks of any size and topology. System infrastructure monitoring and control. Bridging for different radio networks

LD2342 USWM V1.6. LD2342 V1.4 Page 1 of 18

Hytera DMR Conventional Series

SRM9000-Application Note

Cisco IP Interoperability and Collaboration System: Release 4.5

Network Scanner Guide for Fiery S300 50C-KM

GW3-TRBO Trbo Module Software Version 2.14 Module Book

MOTOBRIDGE Dispatch Application Overview

ADVANCED USER S GUIDE

TI2863 Complete Documentation. Internet Transceiver Controller. 1. Device purpose. 2. Device configuration. TI2863 Internet Transceiver Controller

CTI Products RadioPro Dispatch Demo Installation and Test Drive Document # S For Version 8 Software

CTI Products RadioPro Dispatch User Guide Document # S For Version 8 Software

DataCAD 18 Softlock. Universal Installer. Installation. Evaluation

VoIP Paging Amplifier and Elastix Server

Modular Metering System ModbusTCP Communications Manual

FAQ and Solutions. 02 May TM and copyright Imagicle spa

GM1200 User Guide. GM1200 User Guide. English. Contents

TRBOnet Enterprise. Quick Reference Guide. Version 5.2. Internet. US Office Neocom Software Jog Road, Suite 202 Delray Beach, FL 33446, USA

MOTOTRBO CAPACITY MAX

Version 9.3. SmartPTT Enterprise. Release Notes

SmartPTT PLUS 9.1. Radioserver Configurator User Guide

Introduction... 3 Programming the Pyramid 2012/Merlin... 3 Programming the Pyramid Programming the Pyramid 2016 (Continued)...

Solutions ADVANCED SOLUTIONS FOR SMART COMMUNICATIONS. RADIO DISPATCHER FLEET PHONE APP BRIDGE

Genesis Channel Manager

Interface Genius Modem Instruction Manual v1.2.4

GW3-TRBO Affiliation Software Version 2.15 Module Book

DataCAD Softlock License Activation and Management

Connecting radios all over the world. Configuring and using SoftRadio on the dispatcher PC

Connecting radios all over the world. Mimer Parts list

Cisco IPICS Dispatch Console

Connecting radios all over the world. Mimer Parts list

VBRC 4. Radio Communicator. Installer Manual

OPERATING GUIDE VHF DIGITAL TRANSCEIVERS. if1000d. series UHF DIGITAL TRANSCEIVERS. if2000d series. The photo shows the VHF transceiver.

Transcription:

DRG-Series Digital Radio Gateway Hytera DMR USB Donor (Tier-2) Digital Radio Supplement

DRG-Series Digital Radio Gateway Hytera DMR USB Donor (Tier-2) Digital Radio Supplement 2015 Omnitronics Pty Ltd. All rights reserved. ABN: 28 798 126 642 Product Notice No part of the contents of this publication may be reproduced or transmitted in any form or by any means without the prior written consent of Omnitronics. Information contained in this document is provided solely to enable use of Omnitronics products. Omnitronics assumes no liability whatsoever for neither technical or editorial errors that may appear in this document nor does it make a commitment to update the information contained herein. Omnitronics retains the right to make changes to this information at any time and without notice. Trademarks DRG100, DRG200i, DRG600i, Alto, and RediTALK are trademarks of Omnitronics Pty Ltd. All other brand names are the property of their respective holders. Technical Support If you require additional information or assistance with installation or configuration of this product, please contact our technical support at support@omnitronics.com.au or your local sales representative at the appropriate telephone number shown below. When contacting Omnitronics for support, please have your Omnitronics product serial number, system hardware, and system software versions available. Head Office: Omnitronics Pty Ltd 27 Sarich Court Osborne Park, WA 6017 Australia PH: +61 8 9445 2633 FAX: +61 8 9445 1687 main@omnitronics.com.au International Sales Office: Omnitronics Pty Ltd 301 Coronation Drive Milton, QLD 4064 Australia PH: +61 7 3369 5733 FAX: +61 7 3369 5799 sales@omnitronics.com.au North America Office: Omnitronics, Inc. 8301 Cypress Plaza Drive, Suite 100 Jacksonville, FL 32256-4416 USA PH: +1 (904) 425 0336 FAX: +1 (904) 296 8350 admin@omnitronicsworld.com Documentation Feedback Spot an error in this document or have a suggestion for improving it? Omnitronics welcomes your feedback regarding this manual. To provide feedback, you can e-mail your comments to documentation@omnitronics.com.au. Be sure to include the Omnitronics product name and version with your correspondence. Omnitronics will carefully consider all feedback for future improvements to Omnitronics documentation and software. Date: July 2015 Document Part Number: MNL-00149-100 ii

Document Revision History Issue Date Description 1.00 Jul 2015 Original publication Please report any errors or omissions in this document to Omnitronics so that such errors or omissions may be corrected in later issues (see Documentation Feedback on page ii). iii

Contents About this Manual Overview... vii Intended Audience... vii Related Documentation... vii Capabilities Supported... viii Chapter 1 Configuration 1 Viewing the System Status...1 Viewing the Hytera DMR Status...3 Digital Radio Configuration...4 Common Digital Radio Settings...5 Hytera DMR USB Interface Settings...8 Chapter 2 Diagnostics and Statistics 11 Digital Radio Diagnostics... 11 Digital Radio Call... 13 Channel Change... 13 Send Text Message... 14 Remote Radio Commands... 14 Radio Status... 15 Statistics... 16 Omnitronics RTP Statistics... 17 Appendix A Interface Information 21 Connecting the DRG... 21 Known Issues... 21 Appendix B Radio Configuration Information 25 Radio Programming... 25 Notes 31 vii v

vi

About this Manual Overview The DRG-Series of Digital Radio Gateway devices supports many digital-radio functions. However, not all digital radios support all of these functions. Therefore, the DRG device is programmed at the factory for a particular digital-radio interface depending on the type of digital radio you intend to use. This publication supplements the information contained in the DRG-Series Product Manual supplied with your DRG device. The information presented covers the configuration and diagnostics of the Hytera DMR (Tier-2) USB Donor Digital-Radio Interface implemented in your DRG. This interface is designed to operate with the Hytera MD782G radio with 4-wire E&M analog audio connected as well as USB for data and control. The Hytera MD782 must have at least firmware version A6.05.07.006. Intended Audience This supplement is intended for technical support personnel, system and network administrators, who install, configure and maintain the DRG product. Related Documentation In addition to this supplement, the following provides related information. DRG100 Digital Radio Gateway Product Manual (MNL-00106) DRG200i Dual-Channel Digital Radio Gateway Product Manual (MNL-00166) DRG600i 6-Channel Digital Radio Gateway Product Manual (MNL-00169) The following documents define the relevant protocols implemented in the DRG product, which are all available as RFC documents from the Internet Engineering Task Force (IETF): RFC3550 - RTP: A Transport Protocol for Real-Time Applications vii

RFC3551 - RTP Profile for Audio and Video Conferences with Minimal Control RFC2833 - RTP Payload for DTMF Digits, Telephony Tones and Telephony Signals RFC3261 - SIP: Session Initiation Protocol RFC3264 - An Offer/Answer Model with the Session Description Protocol RFC4566 - SDP: Session Description Protocol Capabilities Supported The capability matrix below lists the features supported by the DRG implementing the Hytera DMR USB Donor Tier-2 Digital Radio Interface (MD782G). Capability matrix Capability Hytera DMR T2 USB Donor (MD782G) Hytera DMR T2 IP Repeater (RD962/982) Notes Channel Change D Individual Call D Group Call D All Call D Default Call Type (one or more options) D Linking of digital radios Call Alert D Individual Text D viii Only All Call or Group Call can be configured as default call type. Alto and RediTalk currently make no distinction between incoming individual and group text messages Group Text Incoming Emergency Outgoing Emergency Radio Status ( status message ) Poll Radio Status Radio Check Remote Monitoring Radio Disable/Stun Radio Enable/Revive Radio Kill Lone Worker Man Down GPS Location Services Scanning Talkgroup Registration NA NA Applicable only to trunk protocols Request radio GPS location P D = Demo only; P = Planned for release; NA = Not applicable; = Supported; = Not supported

Chapter 1 Configuration This chapter discusses the configuration of the DRG implementing the Hytera DMR (Digital Mobile Radio) USB (Tier-2) digital-radio interface. All web page images included in this supplement are specific to the DRG100 device; however, the web pages for the other DRG devices will be similar. This chapter includes the following sections: Viewing the System Status Viewing the Hytera DMR Status on page 3 Digital Radio Configuration on page 4 Viewing the System Status Select System Status on the menu to display comprehensive information about the operation of your DRG. All the values displayed on this page are read-only so you cannot make any changes to these values. This page is rendered in your web browser each time you log in to the configuration interface. It shows the version information for both the hardware and the firmware used in the DRG together with its operational status. Figure 1 shows an example of the System Status page for the Hytera DMR (Tier-2) USB interface when logged in under the administrator account if you are logged in under the technician or limited-user account, the information displayed will be the same; however you will not see as many menu items. Most of the information shown on this page is the same for all digital-radio interfaces supported by the DRG for further information, refer to the respective DRG-Series Product Manual. The information that is specific to the Hytera DMR USB Tier-2 interface appears under Digital Radio: Hytera DMR Status and Digital Radio: Hytera DMR Service Status. This is discussed in the following section Viewing the Hytera DMR Status on page 3. Hytera DMR USB Donor T2 Supplement 1

Chapter 1, Configuration Common information Shows status information common to all digital-radio interfaces Interface information Shows status information specific to Hytera DMR USB digital-radio interface Figure 1. System status page for Hytera DMR USB interface 2 DRG-Series Digital Radio Gateway

Viewing the Hytera DMR Status Figure 2 shows the typical interface information you will see for a DRG implementing the Hytera DMR USB interface. Figure 2. System Status page showing Hytera DMR Status The information displayed under the Digital Radio: Hytera DMR Status section includes the following: Radio connection shows the status of the connected radio and whether the DRG is communicating with it correctly. The normal status for the radio is Connected. Other possible status values are: Disconnected, Waiting for radio start-up, Waiting for authentication key, Waiting for connection reply, and Detected other USB device. If you see a status other than Connected, and the status does not change to Connected after a short period of time, you will need to investigate the connection between the DRG and the radio as well as the radio programming (see Appendix B, Radio Configuration Information ). USB Network Status shows the status of the virtual Ethernet network created between the DRG and the radio over the USB interface, and whether the connection is operating correctly. The normal status for the USB network is Connected. The information displayed under the Digital Radio: Hytera DMR Service Status section includes the status of the DMR services together with the ports used and the total number of packets received and transmitted. Hytera DMR USB Donor T2 Supplement 3

Chapter 1, Configuration Digital Radio Configuration Select Digital Radio on the menu to display the Digital Radio configuration page similar to the one shown in Figure 3. This page allows you to disable some of the digital radio capabilities and is the same in basic and advanced modes. Figure 3. Digital radio configuration page for common settings The settings on this page are common to all digital-radio interfaces and are discussed in the next section Common Digital Radio Settings on page 5. 4 DRG-Series Digital Radio Gateway

Common Digital Radio Settings The Digital Radio tab includes common digital radio settings. Omnitronics Gateway Interface The information displayed under Omnitronics Gateway Interface is the same regardless of the digital-radio interface you are configuring, and includes only the following setting: TCP Port is the port the DRG uses for incoming TCP connections the DRG acts as a TCP server accepting incoming connections on this port from other Omnitronics devices. Digital Radio Settings This group of configuration settings controls whether a specific capability is published to the DX-Altus Server, and therefore visible on an Omnitronics Dispatch Console. Some settings may not be supported by your DRG. Disable Channel Change option allows you to disable the capability to change the channel on the radio (this capability will be preconfigured by software provided by the radio manufacturer). Disable Call Alert option disables the ability for the console operator to send an alert to another radio. A call alert allows the console operator to send an alert to another radio requesting that the radio operator call back the console operator (the radio operator acknowledges the alert by pressing PTT). Disable Individual Call option disables the ability to initiate an individual call from a console. Disable Individual Call Timeout option disables individual-call timeouts. Individual Call Timeout is the time (in seconds) that the DRG will wait for individual-call activity before it cancels the individual call and reverts to default call mode. This timeout is only used when the Disable Individual Call Timeout option is not selected. Disable Group Call option disables the ability to initiate a group call from a console to a group of radios. Disable Group Call Timeout option disables group-call timeouts. Group Call Timeout is the time (in seconds) that the DRG will wait for activity before it cancels the group call and reverts to default call mode. This timeout is only used when the Disable Group Call Timeout option above is not selected. Hytera DMR USB Donor T2 Supplement 5

Chapter 1, Configuration Disable All Call timeout option disables the All Call timeout and allows the console operator to immediately setup a new call without the need to wait or cancel the All Call. If this option is not selected (i.e., the timeout is enabled), console operators will have to wait for the timeout before a new call setup is allowed. All Call Timeout is the time (in seconds) that the DRG will wait for activity to cease before it cancels the All Call and reverts to default call mode. This timeout is only used when the Disable All Call timeout option is not selected. Call setup timeout is the timeout applied to call setup when the console operator does not PTT within a reasonable time (see Figure 4 on page 7). The Alto console operator can send a request to set up a specific call type. If the operator presses PTT within the specified timeout, the DRG will set up this call type. However, if no PTT is received during this timeout, the DRG will revert to its default call state. If an incoming call is received during this timeout, the DRG will accept the incoming call and it will cancel the operator s original request. In this case, the operator will have to request the call type again after the incoming call is terminated. Disable Text Messaging disables the ability to send a text message to a specific radio or to a group of radios. Disable GPS prevents GPS co-ordinates generated by the radio from reaching connected dispatch consoles such as Alto and RediTALK, which in turn prevents the connected radio from appearing on the GPS map. Disable Radio GPS Request Update prevents connected dispatch consoles such as Alto and RediTALK from requesting the current GPS co ordinates of the connected radio. Disable Monitor Radio disables access to the Monitor Radio feature from the DRG and any connected dispatch consoles such as Alto. Call timeouts are illustrated in the timing diagram shown in Figure 4 on the following page this timing diagram applies to the digital-radio interface. The Individual Call, Group Call, and All Call timeouts can be configured independently. The purpose of these timeouts is to maintain the connection (call type and recipient) during overs until there is no activity (BUSY/PTT) within the timeout. This call timeout can be enabled or disabled for each call type. 6 DRG-Series Digital Radio Gateway

Figure 4. Digital radio timing diagram If the timeout is disabled, the DRG will apply the default call configuration (All Call) as soon as PTT/Busy is cleared. If the timeout is enabled, the DRG will maintain the call type and recipient and reset this timer after every over. If the timer is allowed to expire (no one pressed PTT within the timeout), the DRG will revert to the default call type. This implies that the next PTT will then setup an All Call. Keep in mind that the radio itself may have similar timers that cannot be interrogated by the DRG. A potential problem in which the DRG may not operate as expected may therefore arise in situations when these timers are allowed to clash with those in the DRG. To alleviate this problem, it is advisable that you set the DRG timers to values greater than the actual radio timers. Hytera DMR USB Donor T2 Supplement 7

Chapter 1, Configuration Hytera DMR USB Interface Settings Select Digital Radio on the menu, and then select Hytera DMR tab to display the Digital Radio Configuration page shown in Figure 5. This shows the digitalradio configuration for Hytera DMR USB donor radios the same settings are available in both basic and advanced modes. Figure 5. Digital radio configuration for Hytera DMR USB Hytera Settings Transmit Gain is the gain applied to the audio that the DRG sends to the Hytera base station and only applies to the digital audio path. The gain value ranges from -10dB to +10dB. Receive Gain is the gain applied to the digital audio that is received from the Hytera base station. This gain value ranges from -10dB to +10dB. 8 DRG-Series Digital Radio Gateway

Network Settings Radio ID is the Identity Number of the donor radio to which the DRG is connected. This number is configured in the donor radio using the Hytera Customer Programming Software (CPS): Conventional > DMR Services > Basic > Basic Setting > Radio ID [Digital] Radio IP address is the IPv4 address of the radio-to-radio interface for the donor radio. This address is dependent on the Radio ID and the radio-to-radio subnet, and is determined by the donor radio using the Hytera Customer Programming Software (CPS): Conventional > General Setting > Network > Radio to Radio Network > Radio IP Radio Control Station IP is the IP address of the PC USB interface for the donor radio. The DRG uses this address to communicate with the Hytera donor radio via the USB interface. The donor radio will automatically allocate the next available IP address for the DRG. Access this setting using the Hytera Customer Programming Software (CPS): Conventional > General Setting > Network > Radio to PC Network > Radio Control Station IP Services GPS Port is the port number on which the DRG listens for GPS updates from the donor radio via the USB interface. Access this setting using the Hytera Customer Programming Software (CPS): Conventional > General Setting > Network > Radio Services > GPS Port TMS Port is the port number that the DRG uses for Text Messaging Services with the donor radio via the USB interface. Access this seting using the Hytera Customer Programming Software (CPS): Conventional > General Setting > Network > Radio Services > TMS Port RCP Port (Call Control) is the port number that the DRG will use for controlling the transmission and reception of calls with the donor radio via the USB interface. Access this setting using the Hytera Customer Programming Software (CPS): Conventional > General Setting > Network > Radio Services > RCP Port Hytera DMR USB Donor T2 Supplement 9

Chapter 2 Diagnostics and Statistics In this chapter, we discuss the diagnostic features of the DRG and how to use these features with the Hytera DMR digital-radio interface. This chapter includes the following topics: Digital Radio Diagnostics Statistics on page 16 Digital Radio Diagnostics The DRG provides a separate diagnostics page for performing basic diagnostics and troubleshooting of the digital-radio interface. Select Digital Radio under the Diagnostics menu to view the Digital Radio Diagnostics page. Figure 6 shows the corresponding page for the Hytera DMR interface. If you have disabled some of the features or capabilities, the number of options available on this page will be reduced. For example, if Text Messaging is disabled, the fields related to text messaging will not be visible. The Digital Radio Diagnostics page is used to test the digital-radio interface of the DRG and to diagnose any problems. Hytera DMR USB Donor T2 Supplement 11

Chapter 2, Diagnostics and Statistics Figure 6. Viewing the digital radio diagnostics page for Hytera DMR USB interface 12 DRG-Series Digital Radio Gateway

Digital Radio Call The Digital Radio Call section includes the following settings: Call Type determines the type of digital radio call to make. Depending on the call type, it may occur as soon as the user clicks the Setup Call button or it may occur on the first Push-To-Talk request after the Setup Call button has been pressed. The options available will depend on the capabilities and configuration of the radio but may include: Default Call Type Next radio call will be the default for this radio Individual Call Group Call All Call Call Alert A call to a single radio A call to all radios in a particular group Calls all radios on the network Sends an alert to one radio. This is sent immediately without waiting for a the next Push To Talk request Destination: Radio ID or Group ID is the identity of the radio, or group of radios, to which you want to send the message. Some of these Call Type options may not be available depending on whether the corresponding call-type option is disabled on the Digital Radio page. For further information about these options, refer to Common Digital Radio Settings on page 5. Select the call type from the Call Type dropdown, type the numerical destination into the Destination: Radio ID or Group ID text box, and then click Setup Call to send the request to the radio this may occur as soon as you click the button or it may occur on the first Push-to-Talk. Channel Change The Channel Change section includes the following setting: Channel Number is the number of the radio channel to select. Type the channel number into the Channel Number text box, and then click Set Channel to send the channel-change request to the radio. This changes the channel on the radio to that specified by the Channel Number setting. This section may or may not be visible depending on whether the option to disable channel change is selected (see the Disable Channel Change option on page 5). Hytera DMR USB Donor T2 Supplement 13

Chapter 2, Diagnostics and Statistics Send Text Message You can use this area to send a text message to the specified radio or group. Message Type allows you to select the type of message to send, which can be Individual or Group. Destination: Radio ID or Group ID is the identity of the radio, or group of radios, to which you want to send the message. Type your text message into the text box and click Send Text to send the message. Remote Radio Commands You can use this area to send commands to the remote radio. Command is the command to send to the radio and can be one of the following: Check Radio, Radio Stun, Radio Revive, or Radio Kill. Destination Radio ID is the identity of the radio to which you want to send the command. Select the command from the Command dropdown list, type the numeric radio identity into the Destination: Radio ID text box, and then click Execute to send the command. The commands available will depend on the capabilities and configuration of the radio and whether the corresponding command option is disabled on the Digital Radio page, but may include the following options: Radio Check Stun Radio Revive Radio Monitor Radio Sends a message to a particular radio ID to determine whether the radio is powered on and receiving. Sends a message to a radio terminal that will temporarily disable the radio. Sends a message to a radio terminal that has previously been stunned to revive the radio. Sends a message to radio terminal and places the radio into monitor mode. For further information about these options, refer to Common Digital Radio Settings on page 5. 14 DRG-Series Digital Radio Gateway

Radio Status The Radio Status section displays the current status of the digital radio connected to the DRG. The contents depend on the functionality of the radio and firmware, and may include the following: Communication Status indicates the current communication state of the link between the DRG and the connected digital radio. It shows OK if the communication link is good or failed if the link is not working Push To Talk indicates whether the radio is currently transmitting (ON) or not transmitting (OFF). Busy indicates whether the radio is currently receiving (ON) or not receiving (OFF). Call Type indicates the current active call type, which can be: All Call, Group Call, or Individual Call. Radio ID indicates the identity of the radio that is receiving or transmitting. Channel Number indicates the currently selected radio channel. Group ID indicates the currently active group (transmitting or receiving). Last Text Message Received shows the last text message received from a radio. Last Text Message Sent shows the last text message sent. Hytera DMR USB Donor T2 Supplement 15

Chapter 2, Diagnostics and Statistics Statistics Select Statistics under the Diagnostics menu to display the Statistics page similar to the one shown in Figure 7. The page is the same in both basic and advanced modes, and provides comprehensive statistics about the operation of the DRG. Figure 7. Viewing the Statistics page for the Hytera DMR USB interface 16 DRG-Series Digital Radio Gateway

Omnitronics RTP Statistics Under Omnitronics RTP Statistics, you can view the various counters and other useful information, which includes the following: RTP receive total packets is the total number of RTP packets received. RTP receive valid packets the number of valid RTP packets received from the remote device. RTP receive invalid packets is the number of packets received that do not contain valid RTP formatting. If this number is very large, it may indicate that this port is being used by some other network protocol. RTP receive valid bytes is the total number of bytes received via RTP. RTP receive sequence errors indicates the number of packets that either were not received or which arrived out of order. If this value is large, it indicates that the network is experiencing packet loss or excessive network jitter. RTP receive packets too late indicates that a packet containing audio arrived at the DRG after it should have been played. If this value is large, it indicates excessive and changing network propagation delays. RTP receive STUN packets indicates the number of value STUN messages received. Some VoIP clients send STUN messages on the RTP port to help determine network configuration. RTP receive MULTICAST packets indicates whether a packet has been received from a multicast address. RTP transmit packets is the number of complete network (UDP) VoIP packets sent, but does not include other packets such as web server data or SNMP packets. RTP transmit bytes is the total number of data bytes sent, and includes the payload data, but it does not include the overhead due to Ethernet protocol. Current transmit bytes per second is an estimate of the current bandwidth usage for VoIP. This will display a non-zero value only if the DRG is currently transmitting audio information. Time since valid RTP packet is the time in milliseconds since the last RTP packet was received. RTCP receive total packets is the total number of RTCP packets received. Hytera DMR USB Donor T2 Supplement 17

Chapter 2, Diagnostics and Statistics RTCP receive valid packets is the number of valid RTCP packets received from the remote device. RTCP receive invalid packets is the number of packets received that do not contain valid RTCP formatting. If this number is very large, it may indicate that this port is being used by some other network protocol. RTCP receive valid bytes is the total number of bytes received via RTCP. RTCP transmit packets is the number of complete network (UDP) VoIP control packets sent, but does not include other packets such as web server data or SNMP packets. RTCP transmit bytes is the total number of control bytes sent, and includes the payload data, but it does not include the overhead due to Ethernet protocol. Time since valid RTCP packet is the time in milliseconds since the last RTCP packet was received. Source Name is the name (address) of other IPR or VoIP devices communicating with this DRG, such as: IPR110Plus:Group1@192.168.0.89 Location is the location or name configured in the remote DRG device, such as DxAltus Radio Channel 1. Firmware Information identifies the firmware, and the version of the firmware, that this IPR device is running. Source IP Address is the source IP address for this audio source, such as 192.168.0.89. Source UDP Port is the UDP Port for this audio source, such as 5004. Received packets is the number of VoIP data packets received from the remote device. Duplicate packets is the number of packets that have been detected containing exactly the same data (network errors). Misordered packets is the number of packets that have arrived out of order, usually due to network delays. Packets arrived too late is the number of packets that have arrived after the point where they should have been played (network errors due to high latency). 18 DRG-Series Digital Radio Gateway

Current playout delay is how much audio (in milliseconds) the DRG device is currently holding in its jitter buffer. Current Busy State is the current state of the Busy (Mute) input. Current PTT State is the current state of the remote audio source requested for the local DRG PTT output. This will appear if the remote site currently has an active busy signal from a connected radio. Silent shows the current state of the RTP audio and whether it is silent or someone is talking. Hytera DMR USB Donor T2 Supplement 19

Appendix A Interface Information This appendix discusses some important interface information about your DRG-Series Hytera-DMR product, and includes the following sections: Connecting the DRG Known Issues Connecting the DRG The information in this section includes details about the interface connection requirements. You will need the following hardware to connect the DRG to the Hytera MD782G radio: Omnitronics interface cable OMC300 (see Figure 8 and Figure 9 on the following pages) Suitable DC power supply: DRG100: 12V@300mA DRG200i: 12V@700mA DRG600i: 12V@1500mA Ethernet connection For the DRG to communicate with the Hytera donor radio, the USB port on the donor radio must be configured using the Hytera Customer Programming Software (CPS). Known Issues No known issues at this time. Hytera DMR USB Donor T2 Supplement 21

Appendix A, Interface Information Figure 8. Interface cable OMC300 (sheet 1) 22 DRG-Series Digital Radio Gateway

Figure 9. Interface cable OMC300 (sheet 2) Hytera DMR USB Donor T2 Supplement 23

Appendix B Radio Configuration Information This appendix outlines how to use the Hytera Customer Programming Software (CPS) for basic radio configuration and the settings that need to be configured in order for the radio to function with the DRG. It is recommended that you use version 6.05.05.019.NA2 or later of the CPS software for compatibility; and an appropriate Hytera USB programming cable for connecting the radio to the CPS. Radio Programming This section provides a step-by-step procedure for programming the Hytera radio using CPS. It is assumed that you know how to use the CPS software. To program the radio 1. Run the CPS software and connect to the radio. 2. Read the configuration from the radio. 3. Under MD782G, select Radio Information. Hytera DMR USB Donor T2 Supplement 25

Appendix A, Interface Information 4. Under Firmware Version, ensure the MD782G radio has firmware version A6.05.07.006 or later installed. The DRG and radio may not operate correctly with older firmware versions (contact your local Hytera representative to obtain the latest firmware for your radio). 5. Under MDG782G > Common, select Setting. 6. Under Mode, ensure Default Operation Mode is set to Conventional System. 26 DRG-Series Digital Radio Gateway

7. Under MD782G > Conventional > General Setting, select Network. 8. Under Radio to PC Network, record the address for Radio Control Station IP, and under Radio to Radio Network record the address for Radio IP. You will need to include these settings in the DRG. Hytera DMR USB Donor T2 Supplement 27

Appendix A, Interface Information 9. Select Forward to PC, set Accessory Port Communication to USB, and set Radio s USB Network communication protocol to NCM. 10. On the same page, scroll down to Radio Services, and record the settings for GPS Port, TMS Port, and RCP Port. You will need to include these settings in the DRG. 28 DRG-Series Digital Radio Gateway

11. Under MD782G > Conventional > DMR Services, select Basic. 12. Under Basic Setting, adjust the Radio ID (Digital) setting to suit your radio, and record the setting. You will need to include this setting in the DRG. Hytera DMR USB Donor T2 Supplement 29

Appendix A, Interface Information 13. On the same page under Encode, select All Call Encode, Private Call Encode, and Group Call Encode. 14. Save the settings, and then Write the settings to the radio. The Hytera radio should now be configured correctly to operate with the DRG. Once you have configured the Hytera radio, you can connect it to the DRG using the supplied Omnitronics OMC300 cable (see Connecting the DRG on page 21). It is recommended that you login to the DRG to view the System Status page. Under Hytera DMR Status, the Radio connection and the USB network status should both show as Connected (see Figure 2 on page 3). 30 DRG-Series Digital Radio Gateway

Notes.................................................................. Hytera DMR USB Donor T2 Supplement 31

DRG-Series Digital Radio Supplement for Hytera DMR USB Donor (Tier-2) Copyright 2015 Omnitronics Pty Ltd MNL-00149-100 07/15 www.omnitronicsworld.com