Stereo Audio DIGITAL-TO-ANALOG CONVERTER 16 Bits, khz Sampling TM FEATURES COMPLETE STEREO DAC: Includes Digital Filter and Output Amp DYNAMIC RANGE: db MULTIPLE SAMPLING FREQUENCIES: 16kHz to khz 8X OVERSAMPLING DIGITAL FILTER SYSTEM CLOCK: 256f S / 384f S NORMAL OR I 2 S DATA INPUT FORMATS SMALL 14-PIN SOIC PACKAGE DESCRIPTION The is a complete low cost stereo audio digital-to-analog converter (DAC), operating off of a 256f S or 384f S system clock. The DAC contains a 3rdorder Σ modulator, a digital interpolation filter, and an analog output amplifier. The accepts 16-bit input data in either normal or I 2 S formats. The digital filter performs an 8X interpolation function and includes de-emphasis at 44.1kHz. The can accept digital audio sampling frequencies from 16kHz to khz, always at 8X oversampling. The is ideal for low-cost, CD-quality consumer audio applications. BCKIN LRCIN DIN Serial Input I/F 8X Oversampling Digital Filter Multi-level Delta-Sigma Modulator Multi-level Delta-Sigma Modulator DAC DAC Low-pass Filter Low-pass Filter V OUT L CAP V OUT R FORMAT Mode Control I/F DM 256f S /384f S Power Supply SCKI V CC GND International Airport Industrial Park Mailing Address: PO Box 114, Tucson, AZ 85734 Street Address: 673 S. Tucson Blvd., Tucson, AZ 8576 Tel: (52) 746-1111 Twx: 91-2-1111 Internet: http://www.burr-brown.com/ FAXLine: (8) 548-6133 (US/Canada Only) Cable: BBRCORP Telex: 66-6491 FAX: (52) 889-151 Immediate Product Info: (8) 548-6132 1 19 Burr-Brown Corporation PDS-1373C Printed in U.S.A. January, 19 SBAS67
SPECIFICATIONS All specifications at 25 C, V CC = 5V, f S = 44.1kHz, and 16-bit input data, SYSCLK = 384f S, unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX UNITS RESOLUTION 16 Bits DATA FORMAT Audio Data Interface Format Standard /I 2 S Audio Data Format Binary Two s Complement Sampling Frequency (f S ) 16 khz Internal System Clock Frequency 256f S /384f S DIGITAL INPUT/OUTPUT Logic Level TTL Input Logic Level V (1) IH 2. VDC V (1) IL.8 VDC Input Logic Current: I (1) IN ±.8 µa DYNAMIC PERFORMANCE (2) f = 991kHz THDN at FS (db) 83 78 db THDN at 6dB 32 db Dynamic Range A-weighted 9 db Signal-to-Noise Ratio A-weighted 9 db Channel Separation 88 db DC ACCURACY Gain Error ±1. ±5. % of FSR Gain Mismatch, Channel-to-Channel ±1. ±5. % of FSR Bipolar Zero Error V OUT = V CC /2 at BPZ ±2 ±5 mv ANALOG OUTPUT Output Voltage Full Scale (db).62 x V CC Vp-p Center Voltage V CC /2 VDC Load Impedance AC Load 1 kω DIGITAL FILTER PERFORMANCE Passband.445 f S Stopband.555 f S Passband Ripple ±.17 db Stopband Attenuation 35 db Delay Time 11.125/f S sec INTERNAL ANALOG FILTER 3dB Bandwidth 1 khz Passband Response f = 2kHz.16 db POWER SUPPLY REQUIREMENTS Voltage Range 4.5 5 5.5 VDC Supply Current 13 18 ma Power Dissipation 65 9 mw TEMPERATURE RANGE Operation 25 85 C Storage 55 125 C NOTES: (1) Pins 1, 2, 3, 12, 13: LRCIN, DIN, BCKIN, DM, FORMAT (Schmitt Trigger Input); Pin 14: SCKI. (2) Dynamic performance specs are tested with 2kHz low pass filter and THDN specs are tested with 3kHz LPF, 4Hz HPF, Average-Mode. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. 2
PIN CONFIGURATION TOP VIEW LRCIN DIN BCKIN NC CAP V OUT R GND 1 2 3 4 5 6 7 PACKAGE INFORMATION SCKI FORMAT DM NC NC V OUT L V CC PACKAGE DRAWING PRODUCT PACKAGE NUMBER (1) U 14 Pin SOIC 235 14 13 12 11 1 9 8 SOIC NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. ABSOLUTE MAXIMUM RATINGS Power Supply Voltage... 6.5V V CC to V DD Difference... ±.1V Input Logic Voltage....3V to (V DD.3V) Power Dissipation... 29mW Operating Temperature Range... 25 C to 85 C Storage Temperature... 55 C to 125 C Lead Temperature (soldering, 5s)... 26 C Thermal Resistance, θ JA... 9 C/W PIN ASSIGNMENTS PIN NAME I/O FUNCTION 1 (1) LRCIN IN Sample Rate Clock Input 2 (1) DIN IN Audio Data Input 3 (1) BCKIN IN Bit Clock Input for Audio Data. 4 NC No Connection 5 CAP Common Pin of Analog Output Amp 6 V OUT R OUT Right-Channel Analog Output 7 GND Ground 8 V CC Power Supply 9 V OUT L OUT Left-Channel Analog Output 1 NC No Connection 11 NC No Connection 12 (2) DM IN De-emphasis Control HIGH: De-emphasis ON LOW: De-emphasis OFF 13 (2) FORMAT Audio Data Format Select HIGH: I 2 S Data Format LOW: Standard Data Format 14 SCKI IN System Clock Input (256f S or 384f S ) NOTES: (1) Schmitt Trigger input. (2) Schmitt Trigger input with internal pull-up. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. 3
TYPICAL PERFORMANCE CURVES At T A = 25 C, V CC = 5V, f S = 44.1kHz, SYSCLK = 256f S, unless otherwise noted. DYNAMIC PERFORMANCE THDN at db (%) THDN vs TEMPERATURE.9 3.2.8 3.1.7 db.6.5.4 6dB.3.2.1 3. 2.9 2.8 2.7 2.6 2.5 2.4 THDN at 6dB (%) SNR (db) SNR, DYNAMIC RANGE vs TEMPERATURE 99 99 SNR Dynamic Range 2.3 93 93 25 25 5 75 85 1 25 25 5 75 85 1 Temperature ( C) Temperature ( C) Dynamic Range (db).9 THDN vs POWER SUPPLY 3.2 99 SNR, DYNAMIC RANGE vs POWER SUPPLY 99 THDN at db (%).8.7.6.5.4.3.2.1 6dB db 3.1 3. 2.9 2.8 2.7 2.6 2.5 2.4 THDN at 6dB (%) SNR (db) SNR Dynamic Range Dynamic Range (db) 4.5 4.75 5. 5.25 5.5 V CC (V) 2.3 93 4.5 4.75 5. 5.25 5.5 V CC (V) 93.16 THDN vs SAMPLING RATE 5.2 SNR, DYNAMIC RANGE vs SAMPLING RATE THDN at db (%).14.12.1.8.6.4 db 6dB 44.1 48 88.2 Sampling Rate (khz) 4.7 4.2 3.7 3.2 2.7 2.2 THDN AT 6dB (%) SNR (db) 93 92 91 9 89 88 SNR Dynamic Range 44.1 48 88.2 Sampling Rate (khz) 93 92 91 9 89 88 Dynamic Range (db) 4
TYPICAL PERFORMANCE CURVES At T A = 25 C, V CC = V DD = 5V, f S = 44.1kHz, and 16-bit input data, SYSCLK = 384f S, unless otherwise noted. DIGITAL FILTER OVERALL FREQUENCY CHARACTERISTIC PASSBAND RIPPLE CHARACTERISTIC 2.2 4.4 db db 6.6 8.8 1.4536f S 1.365f S 2.2675f S 3.1745f S 4.815f S Frequency (Hz) 1.1134f S.2268f S.342f S.4535f S Frequency (Hz) DE-EMPHASIS FREQUENCY RESPONSE (44.1kHz).6 DE-EMPHASIS FREQUENCY ERROR (44.1kHz) 2.4 4.2 Level (db) 6 8 Error (db)..2 1.4 12 5 1 15 2 25.6 4999.8375 9999.675 14999.5125 19999.35 Frequency (khz) Frequency (khz) 5
1/fs LRCIN (pin 1) L_ch R_ch BCKIN (pin 3) AUDIO DATA WORD = 16-BIT DIN (pin 2) 14 15 16 1 2 3 14 15 16 1 2 3 14 15 16 MSB LSB MSB LSB FIGURE 1. Normal Data Input Timing. 1/fs LRCIN (pin 1) L_ch R_ch BCKIN (pin 3) AUDIO DATA WORD = 16-BIT DIN (pin 2) 1 2 3 14 15 16 1 2 3 14 15 16 1 2 MSB LSB MSB LSB FIGURE 2. I 2 S Data Input Timing. LRCKIN 1.4V t BCH t BCL t LB BCKIN 1.4V t BCY t BL DIN 1.4V t DS t DH BCKIN Pulse Cycle Time BCKIN Pulse Width High BCKIN Pulse Width Low BCKIN Rising Edge to LRCIN Edge LRCIN Edge to BCKIN Rising Edge DIN Set-up Time DIN Hold Time : t BCY : t BCH : t BCL : t BL : t LB : t DS : t DH : 1ns (min) : 5ns (min) : 5ns (min) : 3ns (min) : 3ns (min) : 3ns (min) : 3ns (min) FIGURE 3. Audio Data Input Timing. SCKI t SCKIH t SCKIL 2.V.8V System Clock Pulse Width High t SCKIH 13ns (min) System Clock Pulse Width Low t SCKIL 13ns (min) SYSTEM CLOCK The system clock for must be either 256f S or 384f S, where f S is the audio sampling frequency (LRCIN), typically 32kHz, 44.1kHz or 48kHz. The system clock is used to operate the digital filter and the noise shaper. The system clock input (SCKI) is at pin 14. Timing conditions for SCKI are shown in Figure 4. FIGURE 4. System Clock Timing Requirements. 6
has a system clock detection circuit which automatically detects the frequency, either 256f S or 384f S. The system clock should be synchronized with LRCIN (pin 1), but can compensate for phase differences. If the phase difference between LRCIN and system clock is greater than ±6 bit clocks (BCKIN), the synchronization is performed automatically. The analog outputs are forced to a bipolar zero state (V CC /2) during the synchronization function. Table I shows the typical system clock frequency inputs for the. SAMPLING RATE (LRCIN) SYSTEM CLOCK FREQUENCY (MHz) 256f S 384f S 32kHz 8.192 12.288 44.1kHz 11.28 16.934 48kHz 12.288 18.432 TABLE I. System Clock Frequencies vs Sampling Rate. TYPICAL CONNECTION DIAGRAM Figure 5 illustrates the typical connection diagram for used in a stand-alone application. INPUT DATA FORMAT can accept input data in either normal (MSB-first, right-justified) or I 2 S formats. When pin 13 (FORMAT) is LOW, normal data format is selected; a HIGH on pin 13 selects I 2 S format. FORMAT Normal Format (MSB-first, right-justified) 1 I 2 S Format (Philips serial data protocol) TABLE II. Input Format Selection. RESET has an internal power-on reset circuit. The internal power-on reset initializes (resets) when the supply voltage V CC > 2.2V (typ). The power-on reset has an initialization period equal to 124 system clock periods after V CC > 2.2V. During the initialization period, the outputs of the DAC are invalid, and the analog outputs are forced to V CC /2. Figure 6 illustrates the power-on reset and reset-pin reset timing. DE-EMPHASIS CONTROL Pin 12 (DM) enables s de-emphasis function. Deemphasis operates only at 44.1kHz. DM DEM OFF 1 DEM ON (44.1kHz) TABLE III. De-Emphasis Control Selection. 5V Analog 7 8 PCM Audio Data Processor 2 3 1 DIN BCKIN LRCIN GND V CC V L OUT CAP 9 5 1µF Post LPF Lch Analog Out V OUT R 6 Post LPF Rch Analog Out 256f S /384f S CLK 14 SCKI FORMAT DM 13 12 Mode Control FIGURE 5. Typical Connection Diagram. V CC 2.6V 2.2V 1.8V Internal Reset SCKI Clock Reset 124 system (= SCKI) clocks Reset Removal FIGURE 6. Internal Power-On Reset Timing. 7
db 1..5 INTERNAL ANALOG FILTER FREQUENCY RESPONSE (2Hz~24kHz, Expanded Scale) APPLICATION CONSIDERATIONS DELAY TIME There is a finite delay time in delta-sigma converters. In A/D converters, this is commonly referred to as latency. For a delta-sigma D/A converter, delay time is determined by the order number of the FIR filter stage, and the chosen sampling rate. The following equation expresses the delay time of :.5 1. 2 1 1k 1k 24k Frequency (Hz) FIGURE 7. Low Pass Filter Frequency Response. db INTERNAL ANALOG FILTER FREQUENCY RESPONSE (1Hz~1MHz) 1 5 5 1 15 2 25 3 35 4 45 5 55 6 1 1 1k 1k 1k 1M 1M Frequency (Hz) FIGURE 8. Low Pass Filter Wideband Frequency Response. T D = 11.125 x 1/f S For f S = 44.1kHz, T D = 11.125/44.1kHz = 251.4µs Applications using data from a disc or tape source, such as CD audio, CD-Interactive, Video CD, DAT, Minidisc, etc., generally are not affected by delay time. For some professional applications such as broadcast audio for studios, it is important for total delay time to be less than 2ms. OUTPUT FILTERING For testing purposes all dynamic tests are done on the using a 2kHz low pass filter. This filter limits the measured bandwidth for THDN, etc. to 2kHz. Failure to use such a filter will result in higher THDN and lower SNR and Dynamic Range readings than are found in the specifications. The low pass filter removes out of band noise. Although it is not audible, it may affect dynamic specification numbers. The performance of the internal low pass filter from DC to 24kHz is shown in Figure 7. The higher frequency rolloff of the filter is shown in Figure 8. If the user s application has the driving a wideband amplifier, it is recommended to use an external low pass filter. A simple 3rdorder filter is shown in Figure 9. For some applications, a passive RC filter or 2nd-order filter may be adequate. BYPASSING POWER SUPPLIES The power supplies should be bypassed as close as possible to the unit. It is also recommended to include a.1µf ceramic capacitor in parallel with the 1µF tantalum bypass capacitor. 6 GAIN vs FREQUENCY 9 Gain 14 V SIN 1kΩ 1kΩ 68pF 15pF 1kΩ OPA134 1pF Gain (db) 34 54 Phase 9 18 Phase ( ) 74 27 36 1 1k 1k 1k 1M Frequency (Hz) FIGURE 9. 3rd-Order LPF. 8
In Z 1 Z 1 Z 1 8f S 18-Bit Out 48f S (384f S ) 64f S (256f S ) 5-level Quantizer 4 3 2 1 FIGURE 1. 5-Level Σ Modulator Block Diagram. THEORY OF OPERATION The delta-sigma section of is based on a 5-level amplitude quantizer and a 3rd-order noise shaper. This section converts the oversampled input data to 5-level deltasigma format. A block diagram of the 5-level delta-sigma modulator is shown in Figure 1. This 5-level delta-sigma modulator has the advantage of stability and clock jitter over the typical one-bit (2-level) delta-sigma modulator. The combined oversampling rate of the delta-sigma modulator and the internal 8X interpolation filter is f S for a 384f S system clock, and 64f S for a 256f S system clock. The theoretical quantization noise performance of the 5-level delta-sigma modulator is shown in Figure 11. Gain ( db) 5-LEVEL Σ MODULATOR 2 2 4 6 8 1 12 14 16 5 1 15 2 25 Frequency (khz) FIGURE 11. Quantization Noise Spectrum. 9
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI s publication of information regarding any third party s products or services does not constitute TI s approval, warranty or endorsement thereof. Copyright 2, Texas Instruments Incorporated