3-Phase Voltage Monitoring Relay INTERFACE Data Sheet PHOENIX CONTACT - 03/2006 Description Voltage monitoring in 3-phase networks with settable threshold values, settable response delay, monitoring of phase sequence and phase failure, as well as asymmetry monitoring with settable asymmetry and the following functions that can be set with the rotary switch: NDER undervoltage monitoring NDER+SEQ undervoltage and phase sequence monitoring WIN monitoring of the range between the thresholds and WIN+SEQ monitoring of the range between the thresholds and and phase sequence monitoring Make sure you always use the latest documentation. It can be downloaded at www.download.phoenixcontact.com. A conversion table is available on the Internet at www.download.phoenixcontact.com/general/7000_en_00.pdf. This data sheet is valid for all products listed on the following page: 102110_01_en PHOENIX CONTACT GmbH & Co. KG 32823 Blomberg Germany 1 Phone: +49-(0) 5235-3-00 Fax: +49-(0) 5235-3-4 12 00 www.phoenixcontact.com www.phoenixcontact.com/salesnetwork
Ordering Data Description Type Order No. Pcs./Pkt 3-Phase voltage monitoring relay EMD-FL-3V-400 2866064 1 Technical Data Power Supply Supply voltage 24 V 240 V AC/DC Connection terminal blocks (electrically isolated) A1 - A2 Tolerance AC -15%... +10% DC -20%... +25% Nominal frequency 48 Hz... 400 Hz On request 16.6 Hz Nominal operational power 4.5 VA (1.5 W) Measuring Input Time setting range for response delay Measured value Measuring input Connection terminal blocks Overload capacity Input resistance Switching threshold Max. (relative to N ) Min. (relative to N ) Asymmetry 0.1 s 10 s AC sinus (48 Hz 63 Hz) 3(N)~400 V / 230 V (N) - L1 - L2 - L3 3(N)~600 V / 346 V 1 MΩ -20% +30% -30% +20% 5%... 25% / off Accuracy Basic accuracy of scale end value ±5% Setting accuracy of scale end value 5% Repeat accuracy 2% Temperature influence 0.1%/K Contact Side (Output) Contact type Rated voltage in accordance with IEC 60664-1 Switching capacity Device mounted in row (spacing < 5 mm) Device not mounted in row (spacing > 5 mm) Fusing Mechanical service life Electrical service life (ohmic load 1000 VA) Switching rate in accordance with IEC 60947-5-1 Max. (with ohmic load 100 VA) Max. (with ohmic load 1000 VA) Floating PDT (2x) 250 V AC 750 VA (3 A/250 V AC) 1250 VA (5 A/250 V AC) 5 A fast 20 x 10 6 cycles 2 x 10 5 cycles 60/min. 6/min. Climatic Data Ambient temperature Operation (IEC 60068-1/L 508) Storage -25 C +55 C / -25 C +40 C -25 C +70 C Relative humidity 15% 85% Climatic class in accordance with IEC 60721-3-3 3K3 Contamination class in accordance with IEC 60664-1 3 102110_01_en PHOENIX CONTACT 2
General Data Duty cycle 100% Recovery time 500 ms Surge voltage category in accordance with IEC 60664-1 III Rated surge voltage 4 kv Indicators Position of output relay: yellow LED Error in corresponding threshold: red LED Response delay in corresponding threshold: red LED ON / OFF ON / OFF Flashes Housing Material Polyamide PA 6.6, self-extinguishing Degree of protection IP40 Mounting On 35 mm DIN rails in accordance with EN 60715-35 Installation position As desired Dimensions (W x H x D) 22.5 mm x 90 mm x 113 mm (0.886 in. x 3.543 in. x 4.449 in.) Weight approx. 160 g Connection Terminal Blocks Touch-proof Degree of protection Torque, max. Conductor cross section With/without ferrule Without ferrule With/without ferrule Flexible without ferrule Yes IP20 1 Nm 1 x 0.5 2.5 mm 2 1 x 4 mm 2 2 x 0.5 mm 1.5 mm 2 2 x 2.5 mm 2 Structure 1 2 3 4 5 ASYM SEQ REL 5 25 ASYM (%) -20 (%) -30 (%) 0 10 (s) S 0-10 10 0 3 7 +30 +20 W WS FNCTION 3 ~ Voltage monitor EMD-FL-3V-400 3~ Spannungsüberwachung 3~ Voltage monitor LED R < LED R Asymmetry 5...25% Zeit / Time 0,2...10s Schaltschwelle / Limit -30...+20% (N) Schaltschwelle / Limit -20...+30% (N) EMD-FL-3V-400 Ord. No. 28 66 06 4 < Diagramm: NDER, NDER & SEQ Diagramm: WIN, WIN & SEQ 7 8 9 0 6! 1 LED: Asymmetry ASYM 2 LED: Threshold value 3 LED: Threshold value 4 LED: Phase sequence SEQ 5 LED: Output relay REL 6 Potentiometer ASYM Asymmetry 7 Potentiometer 8 Potentiometer 9 Potentiometer response delay 10 Rotary switch function 11 Snap-on foot Figure 1 Structure 102110_01_en PHOENIX CONTACT 3
Installation Danger of fatal injury! Never carry out work on live parts! L1 L2 L3 N The monitoring module can be snapped onto all 35 mm DIN rails in accordance with EN 60715-35. An integrated wide range power supply unit allows voltage in the range of 24 V AC/DC to 240 V AC/DC to be connected. Circuit Diagram! # # ) ) Figure 2 Circuit diagram Connection Examples L1 L2 L3 N 24V 0V " " 8 ) +, + $ & $ & Figure 4 L1 L2 L3 N 15 16 18 25 26 28 Measuring range 3(N)~400 V / 230 V 15 25 15 25 16 18 26 28 16 18 26 28 Figure 5 Measuring range 3(N)~400 V / 230 V with connected neutral conductor Figure 3 Measuring range 3(N)~400 V / 230 V 102110_01_en PHOENIX CONTACT 4
Functional Description LEDs and flash alternately for all functions if the minimum value selected for the measured voltage is greater than the maximum value. If there is a mains fault when the monitoring module is activated, the output relay R remains dropped out and the LED for the relevant threshold lights up. The desired function is set with the rotary switch (Figure 6): = ndervoltage monitoring NDER S = NDER + SEQ / undervoltage monitoring with phase sequence monitoring and phase failure monitoring W = Window function WIN / monitoring of the range between the thresholds and WS = WIN + SEQ / monitoring of the range between the thresholds and with phase sequence monitoring and phase failure monitoring SEQ REL (%) 3 7 0 10 (s) S 16 18 W +20 WS FNCTION EMD-FL-3V-400 M Asymmetry 5...2 Zeit / Time 0,2... Schaltschwelle / Li Schaltschwelle / Li < ndervoltage Monitoring NDER, NDER + SEQ LED REL, R Max Min Figure 7 ndervoltage monitoring NDER, NDER + SEQ When the measured voltage (average of the phase-tophase voltages) falls below the value set on the regulator, the response delay () starts to elapse (red flashes). When the response delay has elapsed (red lights up), output relay R drops out (yellow LED REL does not light up). If the measured voltage falls below the value set on the regulator, the output relay R picks up again (yellow LED REL lights up). Window Function WIN, WIN + SEQ LED REL, R START < Figure 6 Rotary switch < Figure 8 Window function WIN, WIN + SEQ The output relay R picks up (yellow LED REL lights up) if the measured voltage (average of the phase-to-phase voltages) exceeds the value set on the regulator. When the measured voltage exceeds the value set on the regulator, the response delay () starts to elapse (red flashes). When the response delay has elapsed (red lights up), output relay R drops out (yellow LED REL does not light up). The output relay R picks up again (yellow LED REL lights up) when the measured voltage drops below the maximum value again (red does not light up). If the measured voltage falls below the value set on the regulator, the response delay () starts to elapse (red LED flashes). When the response delay has elapsed (red lights up), output relay R drops out (yellow LED REL does not light up). 102110_01_en PHOENIX CONTACT 5
Monitoring Phase Sequence SEQ Phase sequence monitoring can be activated for all functions. If the phase direction of rotation is altered (red LED SEQ lights up), output relay R drops out without delay (yellow LED REL does not light up). Monitoring Phase Failure SEQ If one of the phase voltages fails, the response delay set () begins to elapse (red LED SEQ flashes). When the time delay has elapsed (red LED SEQ lights up), output relay R drops out (yellow LED REL does not light up). Reverse voltages (e.g. motors running on two phases) are not detected by this function. This is done by monitoring asymmetry with a suitable choice of thresholds. Monitoring Asymmetry When the asymmetry of the phase-to-phase voltages exceeds the value set on the ASYM regulator, the response delay () starts to elapse (red LED ASYM flashes). When the response delay has elapsed (red LED ASYM lights up), output relay R drops out (yellow LED REL does not light up). If the neutral conductor is connected, the phase voltages (phase-to-neutral voltage) are also monitored for asymmetry with the neutral conductor. In this particular application, both values are taken for evaluation for asymmetry. As soon as one of the two values exceeds the value set on the ASYM regulator, the response delay starts to elapse (red LED ASYM flashes). When the response delay has elapsed (red LED ASYM lights up), output relay R drops out (yellow LED REL does not light up). Monitoring Neutral Conductor Break via Asymmetry Evaluation A break in the neutral conductor between the system and the supply network is recognized as asymmetry of the phase voltages with the neutral conductor and the response delay () starts to elapse (red LED ASYM flashes). When the response delay has elapsed (red LED ASYM lights up), output relay R drops out (yellow LED REL does not light up). A break in the neutral conductor between the monitoring module and the monitored system cannot be detected. PHOENIX CONTACT 03/2006 102110_01_en PHOENIX CONTACT 6