HBG100P series ~ A File Name:HBG100PSPEC 20160503
HBG100P series SPECIFICATION MODEL OUTPUT INPUT PROTECTION OTHERS NOTE RATED CURRENT RATED POWER CONSTANT CURRENT REGION Note.2 OPEN CIRCUIT VOLTAGE(max.) CURRENT ADJ. RANGE CURRENT RIPPLE CURRENT TOLERANCE SET UP TIME Note.4 VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR EFFICIENCY (Typ.) AC CURRENT INRUSH CURRENT(Typ.) LEAKAGE CURRENT OVER VOLTAGE OVER TEMPERATURE EMC IMMUNITY MTBF DIMENSION PACKING Note.3 TOTAL HARMONIC DISTORTION MAX. No. of PSUs on 16A CIRCUIT BREAKER OVER CURRENT WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE EMC EMISSION HBG100P36 HBG100P48 HBG100P60 2.7A 2A 1.6A 97.2W 96W 96W 21.6 ~ 36V 28.8 ~ 48V 36 ~ 60V 37V 49V 62V Adjustable for AType only (via builtin potentiometer) 1.62 ~ 2.7A 1.2 ~ 2A 1.0 ~ 1.6A 5.0% max. @rated current ±5.0% 2000ms / 115VAC 500ms / 230VAC 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF 0.96/115VAC, PF 0.96/230VAC, PF 0.94/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< (@load 60%/115VC,230VAC; @load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section) 91% 91% 91.5% 1.1A / 115VAC 0.5A / 230VAC 0.45A / 277VAC COLD START 60A(twidth= 415μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC 95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed 41 ~ 49V 54 ~ 63V 65 ~ 75V Shut down o/p voltage, repower on to recovery Shut down o/p voltage, repower on to recovery Ta=40 ~ 45 (Please refer to OUTPUT LOAD vs TEMPERATURE section) 20 ~ 95% RH noncondensing 40 ~ 80, 10 ~ 95% RH ± 0.03%/ (0 ~ 45 ) 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750,CSA C22.2 No.250.1312; ENEC EN613471,EN61347213,EN62384, GB19510.1,GB19510.14 approved I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:0.5KVAC I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN6100032 Class C (@load 60%) ; EN6100033, GB17743, GB17625.1 Compliance to EN6100042,3,4,5,6,8,11, EN61547,light industry level(surge immunity:lineearth:4kv,lineline:2kv) 346.8Khrs min. MILHDBK217F (25 ) Refer to mechanical specification 0.3Kg; 45pcs/14.5Kg/1.60CUFT File Name:HBG100PSPEC 20160503
HBG100P series BLOCK DIAGRAM fosc : 100KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.C.P. V V FG O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. 100 Vo(%) 60 (min.) Hiccup Protection Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 100 Io(%) Typical output current normalized by rated current (%) File Name:HBG100PSPEC 20160503
G G 100W Constant Current Mode LED Driver HBG100P series DIMMING OPERATION AC/L(Brown) AC/N(Blue) FG (Green/Yellow) SJTW 18AWG*3C FS1 ACL ACN ZNR1 C1 LF1 BD1 V(Black) V(Red) SJTW 18AWG*2C V FG V C5 T1 HS1 L1 L100 Q101 Q2 D S Q1 C107 HS2 L3 C106 DIM(WHITE) DIM(BLUE) UL2517 22AWG*2C SVR1 VR2 VR1 CN1 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) Applying additive 1 ~ 10VDC 100% V V DIM DIM Additive Voltage LED Strips Output current (%) 90% 80% 70% 60% 50% 40% 30% DO NOT connect "DIM to V" 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): LED Strips V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input File Name:HBG100PCSPEC 20160503
HBG100P series Applying additive resistance: V V DIM DIM LED Strips Additive Resistance Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% DO NOT connect "DIM to V" 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Switch Adjuster 10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HBG100P BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture. File Name:HBG100PCSPEC 20160503
HBG100P series OUTPUT LOAD vs TEMPERATURE 100 LOAD (%) 80 60 50 40 230VAC Input only 100VAC 230VAC 20 40 25 10 0 15 30 40 45 50 60 (HORIZONTAL) AMBIENT TEMPERATURE, Ta ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC 100 Constant Current Mode 90 1 LOAD (%) 80 70 60 50 40 PF 0.99 0.98 0.97 0.96 0.95 0.94 0.93 277V 230V 115V 90 100 125 135 145 155 165 175 180 200 230 305 INPUT VOLTAGE (V) 60Hz 0.92 0.91 50% 60% 70% 80% 90% 100% Derating is needed under low input voltage. LOAD TOTAL HARMONIC DISTORTION (THD) 60V Model 25% EFFICIENCY vs LOAD HBG100P series possess superior working efficiency that up to 91.5% can be reached in field applications. 60V Model THD 15% 5% 0% 50% 60% 70% 80% 90% 100% 277V 230V 115V EFFICIENCY(%) 94 92 90 88 86 84 82 80 78 76 30% 40% 50% 60% 70% 80% 90% 100% 277V 230V 115V LOAD LOAD File Name:HBG100PSPEC 20160503
HBG100P series MECHANICAL SPECIFICATION Atype ψ24 ψ104 34 1.6 Unit:mm 300±20 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) V(Black) V(Red) Btype AC/L(Brown) AC/N(Blue) FG (Green/Yellow) V(Black) V(Red) SJTW 18AWG*3C 200±20 SJTW 18AWG*2C 300±20 SJTW 18AWG*3C 200±20 SJTW 18AWG*2C C107 V L100 V L100 V V Q101 C106 Io.adj Q101 FS1 ACL ACN G G D D S S G G HS2 FS1 ACL ACN ZNR1 ZNR1 FG SVR1 FG C1 C1 LF1 VR2 VR1 ψ24 LF1 C5 T1 C5 T1 BD1 L1 HS1 Q2 Q1 L3 CN1 ψ104 BD1 L1 HS1 Q2 Q1 34 1.6 C107 HS2 L3 300±20 C106 DIM(White) DIM(Blue) UL2517 22AWG*2C SVR1 VR2 VR1 CN1 File Name:HBG100PSPEC 20160503