IP67 05 { :
SPECIFICATION MODEL OUTPUT OTHERS NOTE XLG25 RATED CURRENT 700mA CONSTANT CURRENT REGION Note.2 22 ~54V RATED POWER Note.5 VAC ~ 305VAC 25W CURRENT RIPPLE 5.0% max. @ rated current OPEN CIRCUIT VOLTAGE (max.) 57V CURRENT ADJ. RANGE 0.25 ~ 1.05A SETUP, RISE TIME Note.3 500ms, 100ms/115VAC, 230VAC VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR EMC IMMUNITY MTBF DIMENSION 25W Constant Power Mode LED Driver Note.5 ~ 305VAC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF 0.97/115VAC, PF 0.95/230VAC, PF 0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) 1305.62 K hrs min. Telcordia SR332 (Bellcore) 399.88Khrs min. MILHDBK217F (25 ) 105* 63*30mm (L*W*H) TOTAL HARMONIC DISTORTION THD< 10%(@load 50%/115VC,230VAC; @load 75%/277VAC) (Please refer to TOTAL HARMONIC DISTORTION(THD) section) INPUT EFFICIENCY (Typ.) Note.10 88% AC CURRENT 0.29A / 115VAC 0.15A / 230VAC 0.13A/277VAC INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER COLD START 50A(twidth=350μ s measured at 50% Ipeak) at 230VAC; Per NEMA 410 5 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC NO LOAD / STANDBY No load power consumption <0.5W for A,<0.75W for I series POWER CONSUMPTION Standby power consumption <0.5W for AB Over Power Protection 110150% Over Power Protection, recovers automatically after fault condition is removed PROTECTION Short Circuit Protection Constant current limiting, recovers automatically after fault condition is removed OVER TEMPERATURE PROTECTION Hiccup mode, recovers automatically after fault condition is removed INPUT OVER VOLTAGE Note.8 320 ~ 370 (Shut down output voltage when the input voltage exceeds protection voltage) can survive input voltage stress of 4Vac for 48 hours WORKING TEMP. Tcase= ~ 85 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=85 ENVIRONMENT WORKING HUMIDITY 20 ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY ~, 10 ~ 95% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ 60 ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS UL8750(type HL ), CSA C22.2 No. 250.1312; ENEC AS/NZS IEC EN613471, AS/NZS EN61347213 independent, EN62384; IP65 or IP67; GB19510.1, GB19510.14 approved SAFETY & WITHSTAND VOLTAGE I/PO/P:3.75KVAC I/PFG:2.0KVAC O/PFG:1.5KVAC EMC ISOLATION RESISTANCE I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH EMC EMISSION Compliance to EN55015,EN6100032 Class C (@load 50%) ; EN6100033; GB17743, GB17625.1 Compliance to EN6100042,3,4,5,6,8,11; EN61547, light industry level ( surge immunity LineEarth 6KV, LineLine 4KV) PACKING 0.41Kg;24pcs/ 10.5Kg/0.68CUFT for Atype 0.42Kg;24pcs/ 11Kg/0.68CUFT for ABtype
Block Diagram PFC fosc : 50~120KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.L.P. Vo Vo O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT CASE :Protective Earth DRIVING METHODS OF LED MODULE 54V 48V 42V 250mA, 54V 500mA,54V 36V 30V 24V 700mA,36V 1050mA, 24V 18V 12V 250mA,22V 500mA, 22V 1050mA, 22V 6V 0V 0mA 175mA 350mA 525mA 700mA 875mA 1050mA 1225mA High Performance Region Operational Region
DIMMING OPERATION AC/N(Blue) AC/L(Brown) PE (Green/Yellow) XLG25 Vo(Red) Vo(Black) DIM( Blue)* DIM(White)** 3 in 1 dimming function (for ABType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) Applying additive 0 ~ 10VDC Vo DO NOT connect "DIM to Vo" Additive Voltage Output current (%) 100% 88% % 70% 60% 50% % 30% 20% 10% * DIM for ABType * *DIM for ABType 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Output current (%) 100% 88% % 70% 60% 50% % 30% 20% 10% 0% 0% 10% 20% 30% % 50% 60% 70% % 88% 100% Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: Vo Vo DIM DIM Short Circuit Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): Vo Vo DIM Additive PWM signal DIM DO NOT connect "DIM to Vo" Vo DIM DIM DO NOT connect "DIM to Vo" Additive Resistance Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. Output current (%) 100% 88% % 70% 60% 50% % 30% 20% 10% 0% Short 10K/N 20K/N 30K/N K/N 50K/N 60K/N 70K/N K/N K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance
OUTPUT LOAD vs TEMPERATURE 100 100 60 230VAC input only 60 230VAC input only LOAD (%) 20 LOAD (%) 20 25 10 0 15 30 50 60 70 AMBIENT TEMPERATURE,Ta ( ) (HORIZONTAL) 25 0 20 45 55 65 75 85 Tcase ( ) (HORIZONTAL) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 75 Constant Current Mode 100 1 0.95 LOAD (%) 70 60 50 0.9 0.85 0.8 0.75 PF 0.7 0.65 0.6 0.55 277V(25W) 230V(25W) 115V(25W) 0.5 100 120 1 160 1 200 220 2 260 2 305 10% 20% 30% % 50% 60% 70% % % 100% INPUT VOLTAGE (V) 60Hz Derating is needed under low input voltage. LOAD THD(%) TOTAL HARMONIC DISTORTION (THD) 50V Model, Tcase at 75 10 9 8 7 6 5 4 3 2 1 0 50% 60% 70% % % 100% 115VAC(25W) 230VAC(25W) 277VAC(25W) EFFICIENCY(%) EFFICIENCY vs LOAD possess superior working efficiency that up to 88% can be reached in field applications. 50V Model, Tcase at 75 92 88 86 84 277V(25W) 82 230V(25W) 78 115V(25W) 76 74 72 70 10% 20% 30% % 50% 60% 70% % % 100% LOAD LOAD
LIFE TIME 120 100 LIFETIME(Kh) 60 20 0 20 30 50 60 70 85 Tc a s e ( )
Mechanical Specification AType CASE NO.: 268A Unit:mm 300±10 105 99 300±10 AC/N(Blue) AC/L(Brown) PE (Green/Yellow) SJOW 17AWGx3C &H05RNF 3x1.0mm 2 31.6 tc 61.3 63 SJOW 17AWGx2C &05RNF 2x1.0mm 2 Vo(Black) Vo(Red) 4ψ4.5 tc : Max. Case Temperature 30 25.8 9.9
ABType 300±10 105 99 300±10 AC/N(Blue) AC/L(Brown) PE (Green/Yellow) SJOW 17AWGx3C &H05RNF 3x1.0mm 2 31.6 4ψ4.5 tc 61.3 tc : Max. Case Temperature 63 SJOW 17AWGx2C &05RNF 2x1.0mm 2 UL2517 20AWGx2C 325±10 Vo(Black) Vo(Red) DIM( Blue)* DIM(White)** * DIM for ABType * *DIM for ABType 30 25.8 9.9 Installation Manual Please refer to : http://www.meanwell.com/manual.html