INTRODUCTION & FEATURES 1 FEATURES & CONTROLS Mono Channel(EV1804D) 2 Channel(EV254, EV294) 4 Channel(EV424, Ev464, EV484) 5 Channel(EV594) SPECIFICATIONS INSTALLATION & PRECAUTIONS SYSTEM WIRING Mono Channel system wiring 2 Channel system wiring 4 Channel system wiring 5 Channel system wiring TROUBLE SHOOTING WIRING 2~6 2 3 4 5 7~8 9 10~20 10~11 12~14 15~17 18~20 21 22
Congratulations on your purchase of a Lanzar EVOLUTION amplifier. You have purchased a quality product designed and engineered to give you many years of uncompromised musical service. EVOLUTION amplifiers are designed with the latest technology available, incorporating a DC to DC Switching Power Supply, which provides headroom for even the most demanding peaks and dynamic ranges found on modern CD's and recordings. Features MOSFET switches maintain rated power over a wide range of battery voltages PWM(Pulse-Width-Modulated) System 2 Ohm Stable Stereo operation Stereo, Bridge Mode and Tri-Mode System Application Compatible Variable input level controls for each pair of channels Variable high and low pass crossover controls Thermal and speaker short protection circuitry Power and Protection LED indicators Bass Boost Circuitry Nickel plated power, RCA and speaker connectors High-efficiency, heavy aluminum heatsink Bass Boost Remote control
1. Input RCA Jacks - These inputs are for signal cables from the source. Always use high quality shielded RCA cables. 2. Line Out RCA Jacks - The LINE OUT allows you to build multiple amplifier systems with out having to use splitter cords to distribute the signal. Now it is simple a matter of bringing one set of RCAs into the first amplifier, then using the line out RCA jacks as the feed to the next amplifier. 3. Level Control- Enables the matching of input levels to the output levels from the head unit(or other signal source). 4.Phase Shift control - Allows you to change the phase of your subwoofer from 0 to 180 degrees to help compensate for timing differences between drivers. 5.Variable Low Pass Filter- When Crossover Mode Selector is in Low Pass Mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 50~500Hz. (MONO AND EV594 SUB@1CH,WITHIN THE RANEG 50-250Hz.) 6.Variable High Pass Filter- When Crossover Mode Selector is in High Pass Mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 50~500Hz. (THIS IS MONO AMP SUBSONIC FILTER WITHIN THE RANGE 15-45Hz) 7.Bridged Mode 8.Bass Boost Remote Control Input 9.Power & Protection Indicators- Provide instant information on status of amplifier, including short-circuit and thermal overload alerts. 10.Variable Bass Boost Control- 0~18dB @ 60Hz FIX. 11.High Inputs- Accepts speaker level inputs from head units that do not line level (RCA) outputs. 12.Crossover mode selector - Determines the mode of built-in crossover: low pass(permits only low frequency signals to pass to speakers), high pass(permits only high frequency signals to pass to speakers),or flat. 13.Speaker Temimal.
RMS at 4 Ohms 400W x 2 800W x 2 250W x 4 375W x 4 500W x 4 Peak at 4 Ohms 800W x 2 1600W x 2 500W x 4 750W x 4 1000W x 4 RMS at 4 Ohm Bridged 800W x 1 1600W x 1 500W x 2 750W x 2 1000W x 2 Peak at 4 Ohm Bridged 1600W x 1 3200W x 1 1000W x 2 1500W x 2 2000W x 2 Low Pass Filter 50Hz~500Hz 50Hz~500Hz 50Hz~500Hz 50Hz~500Hz 50Hz~500Hz High Pass Filter 50Hz~500Hz 50Hz~500Hz 50Hz~500Hz 50Hz~500Hz 50Hz~500Hz Bass Boost Control 0-18dB @ 60Hz FIX 0-18dB @ 60Hz FIX 0-18dB @ 60Hz FIX Input Sensitivity T.H.D 200mV~6V <0.05% Low:200mV~6V High:400mV ~12V <0.05% Low:200mV~6V High:400mV ~12V <0.05% Low:200mV~6V High:400mV ~12V <0.05% Low:200mV~6V High:400mV ~12V <0.05% S/N Ratio >100dB >100dB >100dB >100dB >100dB Channel Separation >60dB >60dB >60dB >60dB >60dB Frequency Response 15Hz~40KHz 15Hz~40KHz 15Hz~40KHz 15Hz~40KHz 15Hz~40KHz Fuse(s) 20Ax2 30Ax3 20Ax2 25Ax3 40Ax3 Dimensions:WxHxL(inches) 8.97" x 2..41" x 11.02" 8.97" x 2..41" x 14.17" 8.97" x 2..41" x 12.83" 8.97" x 2..41" x 15.19" 8.97" x 2..41" x 17.16"
RMS at 4 Ohms RMS at 2 Ohms RMS at 1 Ohm Peak at 1 Ohm Low Pass Filter High Pass Filter Bass Boost Control Input Sensitivity T.H.D S/N Ratio Channel Separation Frequency Response Fuse(s) Dimensions:WxHxL(inches) 500W x 1 1000W x 1 2000W x 1 4000W x 1 50Hz~250Hz (Subsonic@1CH) : 15Hz ~ 45Hz 0-18dB @ 60Hz FIX Low:200mV~6V High:400mV ~12V <0.05% >85dB 15Hz~250Hz 25Ax3 8.97" x 2..41" x 14.17" 312W x 4 RMS at 4 Ohms & 750W x 1 RMS at 2 Ohms 625W x 4 Peak at 4 Ohms & 1500W x 1 Peak at 2 Ohms Tri-Mode 625W x 2 RMS at 2 Ohms Bridged & 1000W x 1 RMS at 1 Ohm Tri-Mode 1250W x 2 Peak at 2 Ohms Bridged & 1500W x 1 Peak at 1 Ohm 50Hz~500Hz / 50Hz~250Hz 50Hz~500Hz (SUB@1CH) :0-18dB @ 60Hz FIX Low:200mV~6V High:400mV ~12V <0.05% >100dB >60dB 15Hz-40KHz/ (SUB@1CH) : 15Hz - 250Hz 40Ax3 8.97" x 2..41" x 17.16"
Mono Fuse Rating MODEL EV 1804D FUSES 25A x 3
Fuse Rating MODEL EV 254 EV 294 FUSES 20A x 2 30A x 3
Fuse Rating MODEL EV 424 EV 464 EV 484 FUSES 20A x 2 25A x 3 40A x 3
Fuse Rating MODEL EV 594 FUSES 40A x 3
STOP STOP 2-channel Amplifier (Operating in Stereo) 2-channel Amplifier (Operating in Bridged Mono) 4-channel Amplifier (Operating in Stereo) 4-channel Amplifier (Operating in Bridged Mono) YES! NO! YES! NO! MOST TWO-CHANNEL AMPLIFIERS DO NOT SUPPORT 2-OHM MONO OPERATION! AMPLIFIER DAMAGE COULD RESULT! MOST FOUR-CHANNEL AMPLIFIERS DO NOT SUPPORT 2-OHM MONO OPERATION! AMPLIFIER DAMAGE COULD RESULT! Sound Around, Inc. 1600 63rd Street Brooklyn, NY 1 1204