Linear parameters Name Value Unit Comment Electrical Parameters Re 3.68 Ohm electrical voice coil resistance at DC Le 0.834 mh frequency independent part of voice coil inductance L2 1.560 mh para-inductance of voice coil R2 5.12 Ohm electrical resistance due to eddy current losses Cmes 405.84 µf electrical capacitance representing moving mass Lces 69.59 mh electrical inductance representing driver compliance Res 36.53 Ohm resistance due to mechanical losses fs 29.9 Hz driver resonance frequency Mechanical Parameters (using laser) Mms 127.220 g mechanical mass of driver diaphragm assembly including air load and voice coil mechanical mass of voice coil and diaphragm without air Mmd (Sd) 123.573 g load Rms 8.582 kg/s mechanical resistance of total-driver losses Cms 0.222 mm/n mechanical compliance of driver suspension Kms 4.50 N/mm mechanical stiffness of driver suspension Bl 17.71 N/A force factor (Bl product)
Lambda s 0.011 suspension creep factor Loss factors Qtp 0.256 total Q-factor considering all losses Qms 2.789 mechanical Q-factor of driver in free air considering Rms only Qes 0.281 electrical Q-factor of driver in free air considering Re only Qts 0.255 total Q-factor considering Re and Rms only Vas 37.6878 l equivalent air volume of suspension n0 0.347 % reference efficiency (2 pi-radiation using Re) Lm 87.60 db characteristic sound pressure level (SPL at 1m for 1W @ Re) Lnom 87.97 db nominal sensitivity (SPL at 1m for 1W @ Zn) rmse Z 5.61 % root-mean-square fitting error of driver impedance Z(f) rmse Hx 4.05 % root-mean-square fitting error of transfer function Hx (f) Series resistor 0.00 Ohm resistance of series resistor Sd 346.36 cm diaphragm area Electrical Impedance The two figures below show the magnitude and the phase response of the measured and estimated transfer function Z(f)= U(f)/I(f) where U is the terminal voltage and I is the current. The solid curve is the ratio of the measured spectra U(f), I(f) while the thin curve is the impedance of the linear driver equivalent circuit using the linear model and the identified electrical parameters shown
Displacement Transfer Function The figure below shows the magnitude of the measured and estimated transfer function Hx(f)= X(f)/U(f) between the voice coil displacement X and the terminal voltage U. The solid black curve is the ratio of the measured spectra X(f), U(f) while the thin black curve is the transfer function based on the linear driver equivalent circuit using the identified electrical and mechanical parameters as well as the creep parameter. The dashed red curve is based on the conventional model without considering the creep factor.
This report is generated by the report generator in the frame software db-lab in the Klippel Analyzer System. Using an existing report as template, the old data are replaced by the results of the current measurement automatically. Date: 01/19/07 Time: 14:51:15 Username: Administrator (c)08/2000 Klippel GmbH Germany - http://www.klippel.de/ KLIPPEL ANALYZER SYSTEM Detailed Report Large Signal Identification (LSI) Driver Name: Driver Comment: Measurement: LSI Woofer+Box Measurement Comment: Nonlinear Parameters
Power Series Expansion Symbol Number Unit Comment Displacement Limits X Bl @ Bl min=82% X C @ C min=75% X L @ Z max=10 % 5.9 mm 4.6 mm 4.7 mm X d @ d2=10% 38.4 mm thresholds can be changed in Processing property page Displacement limit due to force factor variation Displacement limit due to compliance variation Displacement limit due to inductance variation Displacement limit due to IM distortion (Doppler) alpha Heating of voice coil by eddy currents
alphaorg Heating of voice coil by eddy currents (without limits) Rtv K/W thermal resistance coil ==> pole tips rv Ws/Km air convection cooling depending on velocity Rtm K/W thermal resistance magnet ==> environment tau m min thermal time constamt of magnet Ctm Ws/K thermal capacity of the magnet tau v s thermal time constant of voice coil Ctv Ws/K thermal capacity of the voice coil delta Tw K Temperature increase in Warm Resistance Mode delta Tc K Temperature increase in Convection Mode delta Te K Temperature increase in Eddy Mode Pcoil(warm) W Pcoil in warm mode Pcoil(conv) W Pcoil in convection mode Ptv(mag.beg) Ptv(mag.mid) Ptv(mag.end) Ptm(mag.beg) Ptm(mag.mid) Ptm(mag.end) W W W W W W power heating the coil at beginning of magnet mode power heating the coil sampled in the middle of magnet mode power heating the coil at end of magnet mode power heating the magnet at beginning of magnet mode power heating the magnet sampled in the middle of magnet mode power heating the magnet at end of magnet mode f1-0.004068 1/A f2-0.000262 1/A^2 coefficient (1) of Inductance over current (flux modulation) coefficient (2) of Inductance over current (flux modulation) Bl0 = Bl (X=0) 18.113 N/A constant part in force factor Bl1 0.13201 N/Amm Bl2-0.051071 N/Amm^2 Bl3 0.0013792 N/Amm^3 Bl4-0.00059795 N/Amm^4 1st order coefficient in force factor 2nd order coefficient in force factor 3rd order coefficient in force factor 4th order coefficient in force factor
Bl5 Bl6 Bl7 Bl8 N/Amm^5 N/Amm^6 N/Amm^7 N/Amm^8 5th order coefficient in force factor 6th order coefficient in force factor 7th order coefficient in force factor 8th order coefficient in force factor L0 = Le (X=0) 1.0151 mh constant part in inductance L1-0.0035913 mh/mm 1st order coefficient in inductance L2-0.0078351 mh/mm^2 L3 L4 L5 L6 L7 L8 2nd order coefficient in inductance 3rd order coefficient in inductance 3.4595e-005 mh/mm^3 3.3433e-005 mh/mm^4 4th order coefficient in inductance mh/mm^5 5th order coefficient in inductance mh/mm^6 6th order coefficient in inductance mh/mm^7 7th order coefficient in inductance mh/mm^8 8th order coefficient in inductance C0 = Cms (X=0) 0.35584 mm/n constant part in compliance C1 0.0092292 1/N C2-0.0025585 1/Nmm C3 C4 C5 C6 C7 C8-6.2611e- 005 1/Nmm^2 8.6336e-006 1/Nmm^3 1/Nmm^4 1/Nmm^5 1/Nmm^6 1/Nmm^7 1st order coefficient in compliance 2nd order coefficient in compliance 3rd order coefficient in compliance 4th order coefficient in compliance 5th order coefficient in compliance 6th order coefficient in compliance 7th order coefficient in compliance 8th order coefficient in compliance K0 = Kms (X=0) N/mm constant part in stiffness K1-0.082247 N/mm^2 1st order coefficient in stiffness K2 0.024675 N/mm^3 2nd order coefficient in stiffness K3 - N/mm^4 3rd order coefficient in stiffness
0.00026711 K4 3.0833e-005 N/mm^5 4th order coefficient in stiffness Xpse 9.6 mm -Xpse < X < Xpse, range where power series is fitted Derived Loudspeaker Parameters
Linear Parameters Symbol Note: Delta Tv = Tv-Ta Large + Warm Large + Cold Small Signal 42 0 0 K Unit Xprot 9.6 9.6 3.6 mm Comment for accurate small signal parameters, use LPM module increase of voice coil temperature during the measurement maximal voice coil excursion (limited by protection system) Re (Tv) 4.27 3.68 3.68 Ohm (imported) voice coil resistance considering increase of voice coil temperature Tv Le (X=0) 1.02 1.02 0.93 mh voice coil inductance at the rest
L2 (X=0) 1.88 1.88 1.65 mh R2 (X=0) 4.38 4.38 4.05 Ohm Cmes (X=0) Lces (X=0) 501 501 459 µf 90.77 90.77 75.57 mh Res (X=0) 23.48 23.48 17.91 Ohm position of the voice coil para-inductance at the rest position due to the effect of eddy current resistance at the rest position due to eddy currents electrical capacitance representing moving mass electrical inductance at the rest position representing driver compliance resistance at the rest position due to mechanical losses Qms (X=0, Tv) 1.74 1.74 1.40 Qes (Tv) 0.26 0.22 0.25 Qts (X=0, Tv) 0.22 0.20 0.21 mechanical Q-factor considering Rms only electrical Q-factor considering Re (Tv) only total Q-factor considering Re (Tv) and Rms only fs 23.6 23.6 27.0 Hz driver resonance frequency Mms 127.220 127.220 127.220 g Rms (X=0) Cms (X=0) 10.826 10.826 15.466 kg/s 0.36 0.36 0.27 mm/n Bl (X=0) 17.71 17.71 17.71 N/A Vas 60.4090 60.4090 46.1579 l (imported) mechanical mass of driver diaphragm assembly including voice-coil and air load mechanical resistance of total-driver losses mechanical compliance of driver suspension at the rest position (imported) force factor at the rest position (Bl product) equivalent air volume of suspension N0 0.297 0.344 0.344 % reference efficiency (2Pi-sr radiation using Re) Lm 86.9 87.5 87.5 db characteristic sound pressure level Sd 346.36 346.36 346.36 cm diaphragm area Temporal Variations of the Stiffness K MS (t, x=0)
Temporal Variations of the Voice Coil Resistance R E (t)
Transducer State Symbol Value Unit Comment Date 2007-01-19 Time 14:34:41 Serial number 332 Mode Nonlinear Mode 5(7) Record 524/524 Laser signal reliable t 00:14:31 h:min:s measurement time Time remaining 00:00:29 h:min:s recalculated at thermal mode(a) Ei (t) 8.2 % error current measurement Ex (t) 1.8 % error laser measurement Eu (t) 14.5 % error amplifier check Delta Tv (Delta Tlim) 42.0 (60.0) K increase of voice coil temperature (limit) Blmin (Bllim) 40.0 (40.0) % minimal force factor ratio (limit) Cmin (Clim) 44.7 (40.0) % minimal compliance ratio (limit) P (Plim) 48.8832 (80.00) W real electrical input power (limit) Lmin 55.7 % minimal inductance ratio
Pn 92.203179 W nominal electrical input power P Re 36.748031 W Power heating voice coil Irms 2.934 A rms value of the electrical input current Urms 19.204 V rms value of the electrical voltage at the transducer terminals Ipeak 9.979 A peak value of the electrical input current Upeak 68.937 V peak value of the electrical voltage at the transducer terminals PC 1.29 db thermal power compression factor Glarge (Gmax) 9.7 (26.0) db gain of the excitation amplitude increased in the large signal domain (maximum) Mech. system abs. import used to identify mechanical system in absolute quantities Xdc 0.2 mm Xpeak 8.6 mm Xbottom -7.2 mm Xp+ 7.8 mm Xp- -7.2 mm dc component of voice coil excursion measured in the last update intervall positive peak value of voice coil excursion measured in the last update intervall negative peak value (bottom) of voice coil excursion measured in the last update intervall upper limit of displacement range (99% probability) lower limit of displacement range (99% probability) Xprot 9.6 mm maximal voice coil excursion allowed by protection system v rms 0.5 m/s voice coil velocity Db 20.1 % Dl 17.6 % Dc 6.1 % distortion factors representing contribution of nonlinear force factor distortion factor representing contribution of nonlinear inductance distortion factor representing contribution of nonlinear compliance R th total 1.14 K/W Delta Tv / P Re Voltage Probability Density Function pdf(u)
Voltage u peak (t) and Current i peak (t) Voice Coil Temperature Δ T V (t) and Power P(t)
Displacement x(t) Displacement Probability Density Function pdf(x)
Distortion Analysis Remedies for Transducer Nonlinearities
Report generated: Date: 01/19/07 Time: 14:51:55 Username: Administrator (c)08/2000 Klippel GmbH Germany - http://www.klippel.de/