Udriver LC 5/3/35/4W 6/7/8/9mA fixc SC ADV ADVANCED series Product description Fixed output LED Driver Can be either used build-in or independent with clip-on strain-relief (see accessory) Constant current LED Driver Output current 6, 7, 8 or 9 ma Max. output power 6.5, 3, 35 or 4.5 W Nominal life-time up to 5, h For luminaires of protection class I and protection class II Temperature protection as per EN 6347--3 C5e Independent LED Driver with cable clamps 5-year guarantee Properties Casing: polycarbonat, white Type of protection IP Functions Overtemperature protection Overload protection Short-circuit protection No-load protection With strain-relief È Standards, page 3 Wiring diagrams and installation examples, page 4 Data sheet 7/6-LC9-5 www.tridonic.com
LED Driver Udriver LC 5/3/35/4W 6/7/8/9mA fixc SC ADV ADVANCED series 5 / 6 Hz Overvoltage protection 3 V AC, h THD (at 3 V, 5 Hz, full load) < % Output current tolerance3 ± 7.5 % 4, 33 tc Typ. current ripple (at 3 V, 5 Hz, full load) ± 5 % Max. output voltage 6 V Turn on time (at 3 V, 5 Hz, full load).5 s Turn off time (at 3 V, 5 Hz, full load). s Hold on time at power failure (output) s Ambient temperature ta -... +5 C 87,5 97 Ordering data Ambient temperature ta (at life-time 5, h) 4 C Type Article number 97 x 43 x 3 mm LC 5W 6mA fixc SC ADV 57 x 43 x 3 mm LC 3W 7mA fixc SC ADV Storage temperature ts -4... +8 C Dimensions L x W x H Dimensions with strain-relief L x W x H 43 98 64 V Mains frequency 34 4 V AC voltage range 4 Rated supply voltage 3 Technical data Packaging, carton Packaging, low volume Packaging, high volume Weight per pc. 87534 5 pc(s). 48 pc(s). 3,84 pc(s)..99 kg 87534 5 pc(s). 48 pc(s). 3,84 pc(s).. kg LC 35W 7mA fixc SC ADV 87545 5 pc(s). 48 pc(s). 3,84 pc(s).. kg LC 35W 8mA fixc SC ADV 875343 5 pc(s). 48 pc(s). 3,84 pc(s).. kg LC 4W 9mA fixc SC ADV 875344 5 pc(s). 48 pc(s). 3,84 pc(s).. kg Specific technical data Type Output Input current Input power current3 (at 3 V, 5 Hz, (at 3 V, 5 Hz, full load) full load) LC 5W 6mA fixc SC ADV 6 ma.33 A 3. W 3. 6.5 W.95 88 %.9C 8 %.4 V 44 V 774 ma 9 ma 8 C LC 3W 7mA fixc SC ADV 7 ma.53 A 34.3 W 5. 3. W.95 88 %.9C 8 %.4 V 44 V 93 ma, ma 83 C LC 35W 7mA fixc SC ADV 7 ma.74 A 4. W 7.5 35. W.95 88 %.9C 8 % 5. V 5 V 93 ma, ma 75 C LC 35W 8mA fixc SC ADV 8 ma.8 A 4. W. 36. W.95 89 %.9C 83 % 5. V 45 V,3 ma, ma 8 C LC 4W 9mA fixc SC ADV 9 ma. A 45.3 W.5 4.5 W.95 89 %.9C 83 % 5. V 45 V,6 ma, ma 83 C Test result at 3 V, 5 Hz. The trend between min. and full load is linear. 3 Output current is mean value. Output power range Power Efficiency Power Efficiency Min. Max. factor at at full factor at at min. forward forward full load load min. load load voltage voltage Data sheet 7/6-LC9-5 www.tridonic.com Max. output peak current at full load Max. output Max. casing peak current temperature tc at min. load
ACCES- SORIES Strain-relief set 43x3mm Product description Optional strain-relief set for independent applications Transforms the LED Driver into a fully class II compatible LED Driver (e.g. ceiling installation) Easy and tool-free mounting to the LED Driver, screwless cable-clamp channels for long strain-relief (3 x 43 x 3 mm) With screws for short strain-relief (5 x 43 x 3 mm) Overall length = length L (LED Driver) + x 3 mm (long strain-relief set), x 5 mm ( short strain-relief) or long and short strain-relief any combination Standard SC (L = 3 mm) available as non-pre-assembled and pre-assembled Short SC (L = 5 mm) only pre-assembled available ACU SC 3x43x3mm CLIP-ON SR SET ACU SC 3x43x3mm CLIP-ON SR SET 3 (868, non-pre-assembled) (835, non-pre-assembled, 3 pcs. packaging) ACU SC 3x43x3mm CLIP-ON SR PA ACU SC 5x43x3mm CLIP-ON SR PA (8699, pre-assembled) (8574, pre-assembled) 3 3 L 3 43 ACU SC 3x43x3mm CLIP-ON SR SET / PA 3 5 L 5 43 ACU SC 5x43x3mm CLIP-ON SR PA Ordering data Type Article number Packaging carton Packaging outer box Weight per pc. ACU SC 43x3mm CLIP-ON SR SET 868 pc(s). 5 pc(s).. kg ACU SC 43x3mm CLIP-ON SR SET 3 835 3 pc(s). 3 pc(s).. kg ACU SC 3x43x3mm CLIP-ON SR PA 8699 pc(s). 5 pc(s).. kg ACU SC 5x43x3mm CLIP-ON SR PA 8574 pc(s)., pc(s).. kg 868: A carton of pcs. is equal to sets, each with strain-reliefs parts. 835: A carton of 3 pcs. is equal to 3 sets, each with strain-reliefs parts. 8699 + 8574: A carton contains exactly pcs. strain-reliefs (no sets). Data sheet 7/6-LC9-5 www.tridonic.com 3
Standards EN 555 EN 6-3- EN 6-3-3 EN 6347- EN 6347--3 EN 6547 EN 6384 Overload protection If the output voltage range is exceeded the LED Driver reduces the LED output current. If the output voltage is exceeded by a certain degree the driver will start working in a pulsed light output mode. After elimination of the overload the nominal operation is restored automatically. Overtemperature protection The LED Driver will reduce the LED output current or it works in a pulsed light output mode if the temperature reaches a certain degree. Short-circuit behaviour In case of a short circuit on the secondary side (LED) the LED Driver switches off. After elimination of the short-circuit fault the LED Driver will recover automatically. No-load operation The LED Driver will work in a pulsed light output mode to limit the output voltage lower than 6 V which allows the application to be able to work safely when LED string opens due to a failure. Glow-wire test according to EN 6347- with increased temperature of 96 C passed. Mounting of device Max. torque for fixing:.5 Nm/M4 Storage conditions Humidity: 5 % up to max. %, not condensed (max. 56 days/year at %) Storage temperature: -4 C up to max. +8 C The devices have to be within the specified temperature range (ta) before they can be operated. Output over voltage protection The LED Driver will work in a pulsed light output mode to limit the output voltage lower than 6 V, even in fault conditions. Installation instructions The LED module and all contact points within the wiring must be sufficiently insulated against kv surge voltage. Air and creepage distance must be maintained. Replace LED module. Mains off. Remove LED module 3. Wait for seconds 4. Connect LED module again Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs. Expected life-time Type ta 4 C 5 C LC 5W 6mA fixc SC ADV LC 3W 7mA fixc SC ADV LC 35W 7mA fixc SC ADV LC 35W 8mA fixc SC ADV LC 4W 9mA fixc SC ADV Test result at max. output voltage. tc 65 C 75 C Life-time 5, h 3, h tc 67 C 77 C Life-time 5, h 3, h tc 65 C 75 C Life-time 5, h 3, h tc 67 C 77 C Life-time 5, h 3, h tc 68 C 78 C Life-time 5, h 3, h The tc temperature could be higher with different output voltages (refer to the tc vs. output voltage diagram for the details). The LED Drivers are designed for a life-time stated above under reference conditions and with a failure probability of less than %. Data sheet 7/6-LC9-5 www.tridonic.com 4
Maximum loading of automatic circuit breakers Automatic circuit breaker type C C3 C6 C B B3 B6 B Inrush current Installation Ø.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm.5 mm Imax Time LC 5W 6mA fixc SC ADV 3 4 47 5 4 5 A 5 µs LC 3W 7mA fixc SC ADV 3 4 47 5 4 5 A 5 µs LC 35W 7mA fixc SC ADV 3 4 47 5 4 5 A 5 µs LC 35W 8mA fixc SC ADV 3 4 47 5 4 5 A 5 µs LC 4W 9mA fixc SC ADV 3 4 47 5 4 5 A 5 µs Harmonic distortion in the mains supply (at 3 V / 5 Hz and full load) in % THD 3. 5. 7. 9.. LC 5W 6mA fixc SC ADV < < 7 < 3 < 3 < 3 < 3 LC 3W 7mA fixc SC ADV < < 7 < 3 < 3 < 3 < 3 LC 35W 7mA fixc SC ADV < < 7 < 4 < 4 < 3 < 3 LC 35W 8mA fixc SC ADV < < 7 < 3 < 3 < 3 < 3 LC 4W 9mA fixc SC ADV < < 7 < 3 < 3 < 3 < 3 Wiring diagram Installation instructions 4 V 5/6 Hz L N Wiring type and cross section The wiring can be in stranded wires with ferrules or solid with a cross section of.5.5 mm². Strip 8.5 9.5 mm of insulation from the cables to ensure perfect operation of the push-wire terminals. Use one wire for each terminal connector only. L N PRI Uconverter LC... SC ADV LED + LED SEC + Umodule wire preparation:.5.5 mm² 8.5 9.5 mm Release of the wiring Press down the push button and remove the cable from front. Isolation and electric strength testing of luminaires Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production. According to IEC 6598- Annex Q (informative only!) or ENEC 33-Annex A, each luminaire should be submitted to an isolation test with 5 V DC for second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal. The isolation resistance must be at least MΩ. As an alternative, IEC 6598- Annex Q describes a test of the electrical strength with 5 V AC (or.44 x 5 V DC). To avoid damage to the electronic devices this test must not be conducted. Additional information Wiring guidelines All connections must be kept as short as possible to ensure good EMI behaviour. Mains leads should be kept apart from LED Driver and other leads (ideally 5 cm distance) Max. lenght of output wires is m. Secondary switching is not permitted. Incorrect wiring can demage LED modules. The wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.). Additional technical information at www.tridonic.com Technical Data Guarantee conditions at www.tridonic.com Services Life-time declarations are informative and represent no warranty claim. No warranty if device was opened. Data sheet 7/6-LC9-5 www.tridonic.com 5
Diagrams LC 5W 6mA fixc SC ADV Efficiency vs load Power factor vs load Efficiency [%] 95 9 8 Power factor,,98,96,94,9,9,88,86,84,8,8 Input power vs load Input current vs load 35 6 3 4 Input power [W] 5 5 5 Input current [ma] 8 6 4 THD vs load tc vs output voltage THD 8 6 4 8 6 4 tc [ C] 8 ta = 5 C 75 7 ta = 4 C 65 6 Output voltage [%] Data sheet 7/6-LC9-5 www.tridonic.com 6
Diagrams LC 3W 7mA fixc SC ADV Efficiency vs load Power factor vs load Efficiency [%] 95 9 8 Power factor,,98,96,94,9,9,88,86,84,8,8 Input power vs load Input current vs load 4 6 35 4 3 Input power [W] 5 5 Input current [ma] 8 6 4 5 THD vs load tc vs output voltage THD 8 6 4 8 6 4 tc [ C] 8 ta = 5 C 75 7 ta = 4 C 65 6 Output voltage [%] Data sheet 7/6-LC9-5 www.tridonic.com 7
Diagrams LC 35W 7mA fixc SC ADV Efficiency vs load Power factor vs load Efficiency [%] 98 96 94 9 9 88 86 84 5 55 6 65 7 75 8 9 95 Power factor,,98,96,94,9,9,88,86,84,8,8 5 55 6 65 7 75 8 9 95 Input power vs load Input current vs load Input power [W] 45 4 35 3 5 5 5 5 55 6 65 7 75 8 9 95 Input current [ma] 8 6 4 8 6 4 5 55 6 65 7 75 8 9 95 THD vs load tc vs output voltage THD 8 6 4 8 6 4 5 55 6 65 7 75 8 9 95 tc [ C] 8 75 7 ta = 5 C 65 6 ta = 4 C 55 5 55 6 65 7 75 8 9 95 Output voltage [%] Data sheet 7/6-LC9-5 www.tridonic.com 8
Diagrams LC 35W 8mA fixc SC ADV Efficiency vs load Power factor vs load Efficiency [%] 95 9 8 55 6 65 7 75 8 9 95 Power factor,,98,96,94,9,9,88,86,84,8,8 55 6 65 7 75 8 9 95 Input power vs load Input current vs load Input power [W] 45 4 35 3 5 5 5 55 6 65 7 75 8 9 95 Input current [ma] 8 6 4 8 6 4 55 6 65 7 75 8 9 95 THD vs load tc vs output voltage THD 8 6 4 8 6 4 55 6 65 7 75 8 9 95 tc [ C] 8 ta = 5 C 75 7 ta = 4 C 65 6 55 6 65 7 75 8 9 95 Output voltage [%] Data sheet 7/6-LC9-5 www.tridonic.com 9
Diagrams LC 4W 9mA fixc SC ADV Efficiency vs load Power factor vs load Efficiency [%] 95 9 8 55 6 65 7 75 8 9 95 Power factor,,98,96,94,9,9,88,86,84,8,8 55 6 65 7 75 8 9 95 Input power vs load Input current vs load Input power [W] 5 45 4 35 3 5 5 5 55 6 65 7 75 8 9 95 Input current [ma] 5 5 5 55 6 65 7 75 8 9 95 THD vs load tc vs output voltage THD 8 6 4 8 6 4 55 6 65 7 75 8 9 95 tc [ C] 8 ta = 5 C 75 7 ta = 4 C 65 6 55 6 65 7 75 8 9 95 Output voltage [%] Data sheet 7/6-LC9-5 www.tridonic.com