8. Adjustment INSTALLATION MANUAL Full Motion LED, LCD Wall Mount 120 +15-15 +5-5 CAUTION: DO NOT ECEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! Adjust to the desired location tilt. Maintenance Check that the bracket is secure and safe to use at regular intervals(at least every three months). Please contact your distribut if you have any questions. PID:10484 LDA03-446 200x200/ 400x200 300x300/400x400 55" MA 25kg (55lbs) RATED
NOTE: Read the entire instruction manual befe you start installation and assembly. WARNING Component Checklist IMPORTANT: Ensure that you have received all parts accding to the component checklist pri to installation. If any parts are missing faulty, telephone your local distribut f a replacement. Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions warnings, please contact your local distribut. adapter bracket (x2) B This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage serious injury. cable clip (x1) C This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual. wall mount A A llen key (x1) D Make sure that the suppting surface will safely suppt the combined weight of the equipment and all attached hardware and components. Package M If mounting to wood wall studs, make sure that mounting screws are anched into the center of the studs. The use of a stud finder is highly recommended. Always use an assistant mechanical lifting equipment to safely lift and position the equipment. M5x14 (x4) M-A M6x14 (x4) M-B M6x30 (x4) M8x30 (x4) Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power. This product is intended f indo use only. Using this product outdos could lead to product failure and personal injury. Package W M8x50 (x4) washer (x4) small spacer (x8) big spacer (x8) ST6.3x55 (x6) W-A concrete anch (x6) W-B D6 washer (x6) W-C 1 2
1.Separating the Decative Covers from the Wall Mount 2b. F Solid Brick and Concrete Mounting 60mm ((2.4") 2.4") ø 10mm (ø 3/8" ) 1 2a. F Wood Stud Wall Mounting Mark the exact location of mounting holes 55mm (2.2")) (2.2" ø 4.5mm (ø 3/16") 1 2 2 Drill pilot holes Find and mark the exact location of mounting holes 3 Drill pilot holes W-B W-C W-C W-A W-A Screw the wall mount onto the wall Screw the wall mount onto the wall Stud Model 406mm 450mm 600mm 610mm (16") (17.7") (23.6") (24") PID:10484 with arrow head pointing up with arrow head pointing up WARNING Make sure that mounting screws are anched into the center of the studs. The use of a stud finder is highly recommended. WARNING Installers are responsible to provide hardware f other types of mounting situations. Installers must verify that the suppting surface will safely suppt the combined weight of the equipment and all attached hardware and components. 3 Installers must verify that the suppting surface will safely suppt the combined weight of the equipment and all attached hardware and components. 4
3. Installing the Decative Covers 4. Removing the Plastic Cover(F VESA200x200 Mounting) F VESA200x200 mounting,please remove the plastic cover on the metal plate. Use the tool to loosen screws on the metal plate in der to remove the plastic cover. 5 6
5. Installing the Adapter Brackets 5b F Recessed Back Screens to Access A/V Inputs Top of the display 5a F Flat Back Screens M-A M-B Note: Choose the appropriate screws, washers and spacers (if necessary) accding to the type of screen. Position the adapter brackets as close as possible to the center of the display. Screw the adapter brackets onto the display. Tighten all screws but do not over tighten. 7 8
6. Hanging the Display onto the Wall Plate 7. Cable Management safety bolt Tighten bottom bolts to secure display brackets to the mount. Install the cable clip. wall D It is necessary to slightly loosen tighten the adjustment screw using the supplied Allen key. Connect cables to your display and route the cables through the cable clip. Note: Leave slack in cable f arm movement. 9 10