The Height of Healthy Design Mod-E Pro Electric L-Shaped Standing Desk ASSEMBLY AND OPERATION
MultiTable Mod-E Pro Electric L-Shaped Table Base PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly procedures. Check that all the parts shown below were provided with your order. Contact your supplier if any materials are missing. Do not discard the your satisfaction. PARTS PROVIDED Side Legs with Motor (2) Center Leg with Motor (1) Cross Channels (4) Long Left Long Short Right Short Top Supports (3) Center Leg Brackets (2) Center Right Right Glide Left Left Feet (2) Control Unit (1) Digital Keypad (1) Motor Cable (3) Power Cable (1) U-Bracket (8) Cord Clip (12) 5mm Allen Key (1) Fasteners Hole Cover (26) M6x18 (26) Socket Cap Round Bolt Guides (8) M6x15 (12) Socket Cap Bolt CAUTION: Hand-tighten screws only. ADDITIONAL TOOLS REQUIRED Phillips screwdriver Power Drill (wood screws only) #10 x 5/8" (28) Table Top Screw M3x20 (3) Round Head Screw M5x15 (2) Round Head Screw M3.5x16 (12) Flat Head Screw Table Top Bracket (2) CAUTION: Always check that screws used to attach components to the work surface are not too long for the thickness of the surface. Work Surface NOTE: The Mod-E Pro Electric Table Base can be used with 90 or 120 work surfaces. Assembly is the same except for the attachment to the center leg brackets. On the following pages, the illustrations show 90 tables; 120 tables are illustrated only to show the difference in attachment to the center leg brackets. 2
ASSEMBLY MultiTable Mod-E Pro Electric L-Shaped Table Base STEP 1 Place the table top facing down on a soft clean surface. Motor STEP 2 Attach the center leg brackets to the center leg (the leg with the glide on the end opposite the motor). Lay the center leg on the work surface with the motor pointing up. Using the 5mm Allen key and four M6x18 socket cap screws (with round tip), attach the brackets to the motor, as shown. M6x18 Round Point STEP 3 Arrange the side legs, center leg, cross channels and top supports as shown below. Positioning does not need to be exact at this time. The longer cross channels are toward the rear of the table. The longer sections of the cross channels are toward the sides. The set screws on the cross channels face inward, toward each other. Holes on the sides of the outer top supports are offset to the rear. Center Top Support Center Leg Column with Brackets Small Top Holes for Center Bracket Attachment Longer Cross Channel Rear Leg Column Set Screws Inner Cross Channels Leg Column Front Shorter Cross Channel Large Holes Face Outward, Offset Toward Rear Left Top Support Right Top Support 3
MultiTable Mod-E Pro Electric L-Shaped Table Base ASSEMBLY STEP 4 Use the 5mm Allen key to attach the three top supports to the leg columns. Use two M6x18 socket head screws (with round point tip) per top support. Be sure the short side of the outer top supports is toward the rear of the work surface. IMPORTANT: Do not use the M6x15 socket head M6x18 Round Point 5mm Allen Key STEP 5 Use the 5mm Allen key to loosen all 16 set screws on the inward side of the cross channels. Position the outer leg columns and top supports so that the outer top supports are approximately 1" (25mm) from the ends of the table and the center leg top support is centered on the angle of the table. Expand the cross channels to the outer top supports and under the center leg brackets. Center the inner cross channel within the outer cross channels. Loosen Set Screws 5mm Allen Key Loosen Set Screws Expand Cross Channels Inner Cross Channels Outer Cross Channels 4
ASSEMBLY MultiTable Mod-E Pro Electric L-Shaped Table Base STEP 6 Attach the cross outer channels to the outer leg columns with four M6x18 socket head screws per leg. Outer Cross Channels Use a 5mm Allen key. Place the guides into the cross channels. cross channel. Guides 5mm Allen Key M6x18 Round Point STEP 7 Attach the other end of the cross channels to the center leg brackets with two M6x15 socket cap M6x15 90 120 Place the guides into the cross channels Adjust the cross channels so that their two end brackets (see illustration). Use a 5mm Allen key to secure the screws. Outer Cross Channel STEP 8 Attach the feet to the outer leg columns. Place the square opening on the foot over the leg. Rear M6x15 Use the 5mm Allen key and M6x15 socket head The shorter side of the foot should be positioned to the rear of the table. Shorter Side Foot Longer Side Front 5
MultiTable Mod-E Pro Electric L-Shaped Table Base ASSEMBLY STEP 9 (If Attaching to MultiTable Pre-Drilled Table Tops) Adjust the position of the frame over the pre-drilled holes prior to attaching it to the table. STEP 9 (If Attaching to Your Own Table Tops) Adjust the position of the frame before attaching it to the table. Check that the top supports on each side are approximately 1" (25mm) from the ends of the table. The rear of the feet should align with the rear of the table. With feet for a 24" deep table, the rear cross channels will be 6½" from the rear of the table. With feet for a 30" deep table, the rear cross channels will be 9½" from the rear of the table. 6½" with 24" Table 9½" with 30" Table Align Rear of Feet with Rear of Table 90 120 1" Top Supports STEP 10 Attach all three top supports to the table. Use the #10 x 5/8" table top screws (12 total required). supports. #10 x 5/8" Table Top Screws STEP 11 Use the 5mm Allen key to tighten the set screws (16 total) in all four cross channels. Tighten All 16 Set Screws 5mm Allen Key 6
ASSEMBLY MultiTable Mod-E Pro Electric L-Shaped Table Base STEP 12 Attach the cross channels to the table. Position one U-bracket over each section of cross channel, between the set screws, as shown (four brackets total). Use the remaining #10 x 5/8" table top screws (16 total) to fasten the U-brackets to the work surface. #10 x 5/8" Table Top Screws STEP 13 Attach the digital keypad using the three M3-20 Phillips round head screws. Position the digital keypad on the left or right side of the table, according to user preference. Mount the keypad 1 1 / 16 from the front edge of the table and expand to make flush. This will prevent overhang and collision with the keypad. M3x20 Digital Keypad MOUNT 1 1 / 16 FROM EDGE or LINE UP OVER PRE-DRILLED HOLES STEP 14 Attach the control unit using the two M5-15 Phillips round head screws. Position the control unit near the back of the table, on the same side as the digital keypad. Be sure that the cable from the keypad can reach the control unit, and the motor cables can extend from the control unit to all three motors. #10 x 5/8" Table Top Screws Control Unit 7
MultiTable Mod-E Pro Electric L-Shaped Table Base ASSEMBLY STEP 15 Make connections to the control unit and motors. Connect the cable from the digital keypad into the control unit. Connect the motor cables from the control unit to each of the three motors on the table legs. Connect the power cord to the control unit. Plug the power cord into an AC outlet CAUTION: Do not operate the table until after initializing the system. See following step. Digital Keypad Cable Motor Cables Power Cord STEP 16 Initialize the system before testing operation. IMPORTANT: The initialization procedure below must be completed before operating the table. Press and hold the UP and DOWN buttons simultaneously for more than 3 seconds. The legs will begin to move down at half speed of normal operation. Continue to press the UP and DOWN buttons. Press and Hold UP and DOWN Buttons Note: Until the table is turned upright, the DOWN button points up and the UP button points down. The legs will move down to the lowest position, then rebound 1 /16" to 3 /16" (2mm to 5mm) and stop. Release the UP and DOWN buttons at the same time. This completes the initialization procedure. STEP 17 Test operation. Press the UP and DOWN buttons individually to test operation. End your test with the legs lowered and unplug the power cord. If there are problems with operation, check that all cable and cord connections are secure. If problems continue, call ESI Customer Service. STEP 18 Use the cord clips to secure the cables and cords in position. Cables must not interfere with table operation. Cables must not interfere with the user. clips to the table. M3.5x16 Cord Clip 8
ASSEMBLY MultiTable Mod-E Pro Electric L-Shaped Table Base STEP 19 Attach two table tops together. The table top brackets should align with pre-drilled holes on underside of tops. Attach both Table Tops together with the table top brackets and the 8 #10 x 5/8" table top screws. Tighten the 6 set screws remaining on the cross channel. STEP 20 If desired, snap hole covers over all screw holes with guides (26 total). Hole Cover STEP 21 IMPORTANT: There must be 1" (25mm) of clearance on all sides of the work surface (and other moving parts) to ensure free, unobstructed movement. Adjust the leveling glides on the feet to level the work surface, if necessary. Plug the power cord into an AC outlet. See the following pages for operating procedures. 9
ASSEMBLY MultiTable Mod-E Pro Electric L-Shaped Table Base UP Button Digital Display DOWN Button SET Button CAUTION: The initialization procedure must be completed before operating the table. See Step 16 on page 8. Memory Buttons GENERAL OPERATION Move the table up or down by pressing UP the work surface reaches the desired height. or DOWN until The table will continue to move up or down until you release the button or until the maximum or minimum height is reached. Table movement stops when you release the UP or DOWN button. MEMORY STOP POSITIONS Raise or lower the table to the position you want to save. The display on the digital keypad shows the work surface height. Press the S button. Then press the desired memory button 1, 2 or 3 within the next 3 seconds. Position 1, 2 or 3 is now saved. To move the work surface to a memory stop position: Press and hold the desired memory button, 1, 2 or 3. The work surface will move to the saved position and then stop. LOWER STOP POSITION This feature can be used to set the minimum height of the table. Raise or lower the table to the desired minimum height. Press and hold S, then press and hold 1. Continue to press both buttons for about 3 seconds. The letter L appears on the display. This means the minimum height of the table is locked at its current position. Release both buttons. To erase the lower stop position: Press and hold S, then press and hold 2. Continue to press both buttons for about 3 seconds. The letter C appears on the display, indicating the lower stop position has been erased. Release both buttons. If you release the memory button before the saved position is reached, table movement will stop. If there is a memory stop position lower than the lower stop position, the memory stop will be erased.. 10
MultiTable Mod-E Pro Electric L-Shaped Table Base ASSEMBLY CHANGING THE HEIGHT DISPLAY UNITS This function allows you to change the display units from centimeters to inches or the other way around. Press and hold S, then press and hold the DOWN button. Continue to press both buttons for about 3 seconds. The height information will change between centimeters and inches. Release both buttons. ADUSTING THE DIGITAL KEYPAD READOUT This function allows you to change the readout of the digital display. Verify the display unit format (inches or mm), set the table to any height, measure the actual height, an write down the number (inches or mm). Press and hold the S button. Then press and hold the the digital display flashes. button for about 3 s Release ease the buttons then press or t Press the S button agin. The 2nd number on the digital display flashes. Press or to change the 2nd number Press the S button again. The 3rd number on the digital display flashes. Press or to change the 3rd number Press the S button to complete the operation. RESET THE CONTROL UNIT TO FACTORY SETTINGS To reset the control unit to factory settings, re-initialize the table. Press and hold the UP and DOWN buttons simultaneously for more than 3 seconds. The legs will begin to move down at half speed of normal operation. Continue to press the UP and DOWN buttons. The legs will move down to the lowest position, then rebound 1 /16" to 3 /16" (2mm to 5mm) and stop. Release the UP and DOWN buttons at the same time. This completes the initialization procedure. If one or more motors are changed in a system, the control unit must be reset to factory settings. 11
The Height of Healthy Design Quality Design Free Shipping 30-Day No Risk Returns Over 85,000 Sold 855-469-6858 www.multitable.com MultiTable LLC 2255 W Desert Cove Ave., Suite E Phoenix, AZ 85029 2019 MultiTable. All rights reserved. MultiTable Mod-E Pro Electric L-Shaped Table Base - Assembly v-1.2