EMC Test Report. Application for FCC Grant of Equipment Authorization Canada Certification Class II Permissive Change/Reassessment

EMC Test Report Application for FCC Grant of Equipment Authorization Canada Certification Class II Permissive Change/Reassessment Innovation, Science and Economic Development Canada RSS-Gen Issue / RSS 27 Issue 1 FCC Part 15, Subpart E IC CERTIFICATION #: FCC ID: 675A-APINH205 Q9DAPINH205 APPLICANT: TEST SITE(S): Aruba Networks 1 Crossman Ave Sunnyvale, CA 9089 IC SITE REGISTRATION #: 285B-, 285B-7 REPORT DATE: May 16, 2016 REISSUE DATE: May 16, 2016 National Technical Systems - Silicon Valley 109 Boyce Road. Fremont, CA. 958-25 FINAL TEST DATES: May 5, 6, 10 and 11, 2016 TOTAL NUMBER OF PAGES: 117 PROGRAM MGR / QUALITY ASSURANCE DELEGATE / TECHNICAL REVIEWER: FINAL REPORT PREPARER: Mark E Hill Staff Engineer David Guidotti Senior Technical Writer National Technical Systems - Silicon Valley is accredited by the A2LA, certificate number 021.26, to perform the test(s) listed in this report, except where noted otherwise. This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full File: R10161 Rev 1 Page 1

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 REVISION HISTORY Rev# Date Comments Modified By - May 16, 2016 First release 1.0 May 16, 2016 Updated reference to C6.10. Updated test configuration. MEH Test Report R10161 Rev 1 Page 2

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 TABLE OF CONTENTS REVISION HISTORY... 2 TABLE OF CONTENTS... SCOPE... OBJECTIVE... STATEMENT OF COMPLIANCE... 5 DEVIATIONS FROM THE STANDARDS... 5 TEST RESULTS SUMMARY... 6 UNII / LELAN DEVICES... 6 MEASUREMENT UNCERTAINTIES... 8 EQUIPMENT UNDER TEST (EUT) DETAILS... 9 GENERAL... 9 OTHER EUT DETAILS... 9 ANTENNA SYSTEM... 9 ENCLOSURE... 9 MODIFICATIONS... 9 SUPPORT EQUIPMENT... 10 EUT INTERFACE PORTS... 10 EUT OPERATION... 10 TEST SITE... 11 GENERAL INFORMATION... 11 CONDUCTED EMISSIONS CONSIDERATIONS... 11 RADIATED EMISSIONS CONSIDERATIONS... 11 MEASUREMENT INSTRUMENTATION... 12 RECEIVER SYSTEM... 12 INSTRUMENT CONTROL COMPUTER... 12 LINE IMPEDANCE STABILIZATION NETWORK (LISN)... 12 FILTERS/ATTENUATORS... 1 ANTENNAS... 1 ANTENNA MAST AND EQUIPMENT TURNTABLE... 1 INSTRUMENT CALIBRATION... 1 TEST PROCEDURES... 1 EUT AND CABLE PLACEMENT... 1 RADIATED EMISSIONS... 15 CONDUCTED EMISSIONS FROM ANTENNA PORT... 18 BANDWIDTH MEASUREMENTS... 18 SPECIFICATION LIMITS AND SAMPLE CALCULATIONS... 19 CONDUCTED EMISSIONS SPECIFICATION LIMITS: FCC 15.207; FCC 15.107(A), RSS GEN... 19 GENERAL TRANSMITTER RADIATED EMISSIONS SPECIFICATION LIMITS... 20 FCC 15.07 (A) OUTPUT POWER LIMITS... 20 OUTPUT POWER LIMITS LELAN DEVICES... 20 SPURIOUS EMISSIONS LIMITS UNII AND LELAN DEVICES... 21 SAMPLE CALCULATIONS - CONDUCTED EMISSIONS... 22 SAMPLE CALCULATIONS - RADIATED EMISSIONS... 22 SAMPLE CALCULATIONS - FIELD STRENGTH TO EIRP CONVERSION... 2 APPENDIX A TEST EQUIPMENT CALIBRATION DATA... 2 APPENDIX B TEST DATA... 25 END OF REPORT... 117 Test Report R10161 Rev 1 Page

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 SCOPE An electromagnetic emissions test has been performed on the Aruba Networks model APINH205, pursuant to the following rules: RSS-Gen Issue General Requirements for Compliance of Radio Apparatus RSS 27 Issue 1 Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSS) and Licence-Exempt Local Area Network (LE-LAN) Devices FCC Part 15, Subpart E requirements for UNII Devices Conducted and radiated emissions data has been collected, reduced, and analyzed within this report in accordance with measurement guidelines set forth in the following reference standards and as outlined in National Technical Systems - Silicon Valley test procedures: ANSI C6.10-201 FCC General UNII Test Procedures KDB7890 The intentional radiator above has been tested in a simulated typical installation to demonstrate compliance with the relevant Industry Canada performance and procedural standards. Final system data was gathered in a mode that tended to maximize emissions by varying orientation of EUT, orientation of power and I/O cabling, antenna search height, and antenna polarization. Every practical effort was made to perform an impartial test using appropriate test equipment of known calibration. All pertinent factors have been applied to reach the determination of compliance. OBJECTIVE The primary objective of the manufacturer is compliance with the regulations outlined in the previous section. Prior to marketing in the USA, all unlicensed transmitters and transceivers require certification. Receive-only devices operating between 0 MHz and 960 MHz are subject to either certification or a manufacturer s declaration of conformity, with all other receive-only devices exempt from the technical requirements. Prior to marketing in Canada, Class I transmitters, receivers and transceivers require certification. Class II devices are required to meet the appropriate technical requirements but are exempt from certification requirements. Certification is a procedure where the manufacturer submits test data and technical information to a certification body and receives a certificate or grant of equipment authorization upon successful completion of the certification body s review of the submitted documents. Once the equipment authorization has been obtained, the label Test Report R10161 Rev 1 Page

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 indicating compliance must be attached to all identical units, which are subsequently manufactured. Maintenance of compliance is the responsibility of the manufacturer. Any modification of the product which may result in increased emissions should be checked to ensure compliance has been maintained (i.e., printed circuit board layout changes, different line filter, different power supply, harnessing or I/O cable changes, etc.). STATEMENT OF COMPLIANCE The tested sample of Aruba Networks model APINH205 complied with the requirements of the following regulations: RSS 27 Issue 1 Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSS) and Licence-Exempt Local Area Network (LE-LAN) Devices FCC Part 15, Subpart E requirements for UNII Devices Maintenance of compliance is the responsibility of the manufacturer. Any modifications to the product should be assessed to determine their potential impact on the compliance status of the device with respect to the standards detailed in this test report. The test results recorded herein are based on a single type test of Aruba Networks model APINH205 and therefore apply only to the tested sample. The sample was selected and prepared by Rob Hastings of Aruba Networks. DEVIATIONS FROM THE STANDARDS Testing is based on a software change reducing power to address spurious emission near the band of operation. The spurious emissions testing was limited to specific frequency ranges observed in preliminary testing. Power measurements were performed to confirm final output power levels. Test Report R10161 Rev 1 Page 5

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 TEST RESULTS SUMMARY UNII / LELAN DEVICES OPERATION IN THE 5.15 5.25 GHZ BAND ACCESS POINTS FCC Measured Value / Description Rule Part Comments a: 19.2dBm (82.6 mw) n20: 19.2dBm (8.5 mw) n0: 19.0dBm (80.1 15.07 (a) (1) mw) Output Power (ii) ac80: 1.9dBm (0.7 mw) Limit / Requirement 0 dbm EIRP <= W Result Complies 15.07(b) (1) / 15.209 Spurious Emissions above 1GHz (Max eirp: 25.2dBm (0.2W)) 5.9 dbµv/m @ 599.0 MHz (-0.1 db) Refer to the limits section (p20) for restricted bands, all others -27 dbm/mhz EIRP Complies OPERATION IN THE 5.15 5.25 GHZ BAND RSS Rule Part Description RSS-27 6.2.1 (1) EIRP Output Power RSS-27 6.2.1 (2) Spurious Emissions above 1GHz Measured Value / Comments ac80: 20.9dBm (0.12 W) 5.9 dbµv/m @ 599.0 MHz (-0.1 db) Limit / Requirement 2 dbm (200 mw) Refer to the limits section (p20) for restricted bands, all others -27 dbm/mhz EIRP 26 dbc in 5.25-5.5 GHz band Result Complies Complies OPERATION IN THE 5.25 5.5 GHZ BAND FCC RSS Description Rule Part Rule Part 15.07(a) (2) RSS-27 6.2.1 (2) Output Power Measured Value / Comments a: 18.7dBm (7.1 mw) n20: 18.9dBm (77.6 mw) n0: 18.7dBm (7.1 mw) ac80: 15.6dBm (6.5 mw) Limit / Requirement 2 dbm (250 mw) EIRP <= 1W Result (margin) Complies 15.07(b) (2) / 15.209 RSS-27 6.2.2 (2) Spurious Emissions above 1GHz (Max eirp: 2.9 dbm (06.5 mw)) 5.8 dbµv/m @ 517.9 MHz (-0.2 db) Refer to the limits section (p20) for restricted bands, all others -27 dbm/mhz EIRP Complies Test Report R10161 Rev 1 Page 6

National Technical Systems - Silicon Valley OPERATION IN THE 5.7 5.725 GHZ BAND FCC RSS Description Rule Part Rule Part 15.07(a) (2) RSS-210 A9.2(2) Output Power Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 Measured Value / Comments a: 18.dBm (67.8mW) n20: 18.dBm (69.0 mw) n0: 19.1dBm (81.0 mw) ac80: 19.5dBm (88.6 mw) Limit / Requirement 2 dbm (250 mw) EIRP <= 1W Result (margin) Complies 15.07(b) () / 15.209 RSS-27 6.2. (2) RSS-27 6.2. Spurious Emissions above 1GHz Non-operation in 5600 5650 MHz sub band (Max eirp: 25.5 dbm (52.7 mw)) 52.2 dbµv/m @ 559. MHz (-1.8 db) Refer to the limits section (p20) for restricted bands, all others -27 dbm/mhz EIRP Device cannot operate in the 5600 5650 MHz band Complies Complies OPERATION IN THE 5.725 5.85 GHZ BAND FCC RSS Description Rule Part Rule Part 15.07(a) () RSS-210 A9.2(2) Output Power (multipoint systems) Measured Value / Comments a: 19.dBm (85. mw) n20: 19.5dBm (88. mw) n0: 19.dBm (87.9 mw) ac80: 16.2dBm (1.9 mw) Limit / Requirement 0 dbm (1 W) EIRP <= W Result (margin) Complies 15.07(b) () / 15.209 RSS-27 6.2. (2) Spurious Emissions above 1GHz (Max eirp: 25.5dBm (51.9mW)) 65. dbµv/m @ 592. MHz (-2.9 db) Refer to the limits section (p20) for restricted bands, all others -17 dbm/mhz EIRP bandedge and -27 dbm/mhz EIRP Complies Test Report R10161 Rev 1 Page 7

National Technical Systems - Silicon Valley MEASUREMENT UNCERTAINTIES Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 ISO/IEC 17025 requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level and were calculated in accordance with UKAS document LAB. Measurement Type Measurement Unit Frequency Range Expanded Uncertainty RF power, conducted (power meter) dbm 25 to 7000 MHz ± 0.52 db RF power, conducted (Spectrum dbm 25 to 7000 MHz ± 0.7 db analyzer) Conducted emission of transmitter dbm 25 to 26500 MHz ± 0.7 db Conducted emission of receiver dbm 25 to 26500 MHz ± 0.7 db Radiated emission (substitution method) dbm 25 to 26500 MHz ± 2.5 db 25 to 1000 MHz ±.6 db Radiated emission (field strength) dbμv/m 1000 to 0000 MHz ± 6.0 db Conducted Emissions (AC Power) dbμv 0.15 to 0 MHz ± 2. db Test Report R10161 Rev 1 Page 8

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 EQUIPMENT UNDER TEST (EUT) DETAILS GENERAL The Aruba Networks model APINH205 is an access point that is designed to be used in wireless networks. Since the EUT could be placed in any location in use, the EUT was treated as tabletop equipment during testing to simulate the end-user environment. The electrical rating of the EUT is 8Vdc supplied either via POE or an AC adapter rated 100-20V, 7-6 Hz, 0.75 Amps.. The sample was received on May 5, 2016 and tested on May 5, 6, 10 and 11, 2016. The EUT consisted of the following component(s): Company Model Description Serial Number FCC ID Aruba Networks APINH205-2 Access Point DN0010196 Q9DAPINH205 OTHER EUT DETAILS 802.11AC 2x2 dual radio access point One radio fixed 2.GHz, second radio fixed 5GHz Radios can transmit simultaneous Each radio is 2x2, does not support 1Tx modes 2.GHz radio supports 11b/11g/n20/n0 data rates 5GHz radio supports 11a/n20/n0/VHT20/VHT0/VHT80 data rates Operation on CH1 (20MHz), CH12 (0MHz), CH18 (80MHz) is supported DFS Master Device Indoor Use only Internal antennas ANTENNA SYSTEM ENCLOSURE The antenna system consists of: Metal Sheet with dbi Gain Antennas for 2.GHz Band and 6dBi Antenna for 5GHz Band The EUT enclosure is primarily constructed of metal and plastic. It measures approximately 8.x.7x15cm. MODIFICATIONS No modifications were made to the EUT during the time the product was at NTS Silicon Valley. Test Report R10161 Rev 1 Page 9

National Technical Systems - Silicon Valley SUPPORT EQUIPMENT No local support equipment was used during testing. Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 The following equipment was used as remote support equipment for emissions testing: Company Model Description Serial Number FCC ID Dell E50 Laptop GDPNP12 DoC NetGear FS05 Switch - - EUT INTERFACE PORTS The I/O cabling configuration during testing was as follows: Port Connected To Cable(s) Description Shielded or Unshielded Length(m) DC Power In AC/DC Adapter 2Wire Unshielded 1.9 Serial USB/Serial Adapter / Remote Multiconductor Shielded 5.0 Laptop USB Not connected - - - Ethernet (x) Bottom Remote Switch CAT5 Unshielded 10 ENET0 (back) Remote Switch CAT5 Unshielded 10 Pass Through (back) Remote Switch CAT5 Unshielded 10 EUT OPERATION The laptop computer was used to configure the system for continuous transmission via the serial connection. The EUT was configured to transmit continuously at the channel noted at the worse case data rate for the mode under test. Power was set to the maximum. Test Report R10161 Rev 1 Page 10

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 TEST SITE GENERAL INFORMATION Final test measurements were taken at the test sites listed below. Pursuant to section 2.98 of the FCC s Rules and section. of RSP-100, construction, calibration, and equipment data has been filed with the Commission and with industry Canada. Site Designation / Registration Numbers FCC Canada Location Chamber US0027 285B- 109 Boyce Road Chamber 7 US0027 285B-7 Fremont, CA 958-25 ANSI C6. recommends that ambient noise at the test site be at least 6 db below the allowable limits. Ambient levels are below this requirement. The test site(s) contain separate areas for radiated and conducted emissions testing. Considerable engineering effort has been expended to ensure that the facilities conform to all pertinent requirements of ANSI C6.. CONDUCTED EMISSIONS CONSIDERATIONS Conducted emissions testing is performed in conformance with ANSI C6.10. Measurements are made with the EUT connected to the public power network through a nominal, standardized RF impedance, which is provided by a line impedance stabilization network, known as a LISN. A LISN is inserted in series with each current-carrying conductor in the EUT power cord. RADIATED EMISSIONS CONSIDERATIONS The FCC has determined that radiation measurements made in a shielded enclosure are not suitable for determining levels of radiated emissions. Radiated measurements are performed in an open field environment or in a semi-anechoic chamber. The test sites are maintained free of conductive objects within the CISPR defined elliptical area incorporated in ANSI C6. guidelines and meet the Normalized Site Attenuation (NSA) requirements of ANSI C6.. Test Report R10161 Rev 1 Page 11

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 MEASUREMENT INSTRUMENTATION RECEIVER SYSTEM An EMI receiver as specified in CISPR 16-1-1 is used for emissions measurements. The receivers used can measure over the frequency range of 9 khz up to 2000 MHz. These receivers allow both ease of measurement and high accuracy to be achieved. The receivers have Peak, Average, and CISPR (Quasi-peak) detectors built into their design so no external adapters are necessary. The receiver automatically sets the required bandwidth for the CISPR detector used during measurements. If the repetition frequency of the signal being measured is below 20Hz, peak measurements are made in lieu of Quasi-Peak measurements. For measurements above the frequency range of the receivers, a spectrum analyzer is utilized because it provides visibility of the entire spectrum along with the precision and versatility required to support engineering analysis. Average measurements above 1000MHz are performed on the spectrum analyzer using the linear-average method with a resolution bandwidth of 1 MHz and a video bandwidth of 10 Hz, unless the signal is pulsed in which case the average (or video) bandwidth of the measuring instrument is reduced to onset of pulse desensitization and then increased. INSTRUMENT CONTROL COMPUTER Software is used to view and convert receiver measurements to the field strength at an antenna or voltage developed at the LISN measurement port, which is then compared directly with the appropriate specification limit. This provides faster, more accurate readings by performing the conversions described under Sample Calculations within the Test Procedures section of this report. Results are printed in a graphic and/or tabular format, as appropriate. A personal computer is used to record all measurements made with the receivers. The software used for radiated and conducted emissions measurements is NTS EMI Test Software (rev 2.10) LINE IMPEDANCE STABILIZATION NETWORK (LISN) Line conducted measurements utilize a fifty microhenry Line Impedance Stabilization Network as the monitoring point. The LISN used also contains a 250 uh CISPR adapter. This network provides for calibrated radio frequency noise measurements by the design of the internal low pass and high pass filters on the EUT and measurement ports, respectively. Test Report R10161 Rev 1 Page 12

National Technical Systems - Silicon Valley FILTERS/ATTENUATORS Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 External filters and precision attenuators are often connected between the receiving antenna or LISN and the receiver. This eliminates saturation effects and non-linear operation due to high amplitude transient events. ANTENNAS A loop antenna is used below 0 MHz. For the measurement range 0 MHz to 1000 MHz either a combination of a biconical antenna and a log periodic or a bi-log antenna is used. Above 1000 MHz, horn antennas are used. The antenna calibration factors to convert the received voltage to an electric field strength are included with appropriate cable loss and amplifier gain factors to determine an overall site factor, which is then programmed into the test receivers or incorporated into the test software. ANTENNA MAST AND EQUIPMENT TURNTABLE The antennas used to measure the radiated electric field strength are mounted on a nonconductive antenna mast equipped with a motor-drive to vary the antenna height. Measurements below 0 MHz are made with the loop antenna at a fixed height of 1m above the ground plane. ANSI C6.10 specifies that the test height above ground for table mounted devices shall be 1.5m for measurements above 1GHz and 80 centimeters for measurements below 1GHz. Floor mounted equipment shall be placed on the ground plane if the device is normally used on a conductive floor or separated from the ground plane by insulating material from to 12 mm if the device is normally used on a non-conductive floor as specified in ANSI C6.. During radiated measurements, the EUT is positioned on a motorized turntable in conformance with this requirement. INSTRUMENT CALIBRATION All test equipment is regularly checked to ensure that performance is maintained in accordance with the manufacturer's specifications. All antennas are calibrated at regular intervals with respect to tuned half-wave dipoles. An exhibit of this report contains the list of test equipment used and calibration information. Test Report R10161 Rev 1 Page 1

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 TEST PROCEDURES EUT AND CABLE PLACEMENT The regulations require that interconnecting cables be connected to the available ports of the unit and that the placement of the unit and the attached cables simulate the worst case orientation that can be expected from a typical installation, so far as practicable. To this end, the position of the unit and associated cabling is varied within the guidelines of ANSI C6.10, and the worst-case orientation is used for final measurements. Test Report R10161 Rev 1 Page 1

National Technical Systems - Silicon Valley RADIATED EMISSIONS Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 A preliminary scan of the radiated emissions is performed in which all significant EUT frequencies are identified with the system in a nominal configuration. At least two scans are performed, one scan for each antenna polarization (horizontal and vertical; loop parallel and perpendicular to the EUT). During the preliminary scans, the EUT is rotated through 60, the antenna height is varied (for measurements above 0 MHz) and cable positions are varied to determine the highest emission relative to the limit. Preliminary scans may be performed in a fully anechoic chamber for the purposes of identifying the frequencies of the highest emissions from the EUT. A speaker is provided in the receiver to aid in discriminating between EUT and ambient emissions. Other methods used during the preliminary scan for EUT emissions involve scanning with near field magnetic loops, monitoring I/O cables with RF current clamps, and cycling power to the EUT. Final maximization is a phase in which the highest amplitude emissions identified in the spectral search are viewed while the EUT azimuth angle is varied from 0 to 60 degrees relative to the receiving antenna. The azimuth, which results in the highest emission is then maintained while varying the antenna height from one to four meters (for measurements above 0 MHz, measurements below 0 MHz are made with the loop antenna at a fixed height of 1m). The result is the identification of the highest amplitude for each of the highest peaks. Each recorded level is corrected in the receiver using appropriate factors for cables, connectors, antennas, and preamplifier gain. When testing above 18 GHz, the receive antenna is located at 1meter from the EUT and the antenna height is restricted to a maximum of 2.5 meters. Test Report R10161 Rev 1 Page 15

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 REAR VIEW 0.m AC Outlets (flush-mounted) 0.8m SIDE VIEW Typical Test Configuration for Radiated Field Strength Measurements Test Report R10161 Rev 1 Page 16

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 EUT d Antenna The anechoic materials on the walls and ceiling ensure compliance with the normalized site attenuation requirements of CISPR 16 / CISPR 22 / ANSI C6. for an alternate test site at the measurement distances used. Floor-standing equipment is placed on the floor with insulating supports between the unit and the ground plane. EUT d 0.8m Antenna height range 1 to m Test Configuration for Radiated Field Strength Measurements Semi-Anechoic Chamber, Plan and Side Views Test Report R10161 Rev 1 Page 17

National Technical Systems - Silicon Valley CONDUCTED EMISSIONS FROM ANTENNA PORT Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 Direct measurements of power, bandwidth and power spectral density are performed, where possible, with the antenna port of the EUT connected to either the power meter or spectrum analyzer via a suitable attenuator and/or filter. These are used to ensure that the front end of the measurement instrument is not overloaded by the fundamental transmission. EUT Attenuator (optional) Spectrum Analyzer (or Power Meter) Test Configuration for Antenna Port Measurements Measurement bandwidths (video and resolution) are set in accordance with the relevant standards and NTS Silicon Valley s test procedures for the type of radio being tested. When power measurements are made using a resolution bandwidth less than the signal bandwidth the power is calculated by summing the power across the signal bandwidth using either the analyzer channel power function or by capturing the trace data and calculating the power using software. In both cases the summed power is corrected to account for the equivalent noise bandwidth (ENBW) of the resolution bandwidth used. If power averaging is used (typically for certain digital modulation techniques), the EUT is configured to transmit continuously. Power averaging is performed using either the built-in function of the analyzer or, if the analyzer does not feature power averaging, using external software. In both cases the average power is calculated over a number of sweeps (typically 100). When the EUT cannot be configured to continuously transmit then either the analyzer is configured to perform a gated sweep to ensure that the power is averaged over periods that the device is transmitting or power averaging is disabled and a max-hold feature is used. If a power meter is used to make output power measurements the sensor head type (peak or average) is stated in the test data table. BANDWIDTH MEASUREMENTS The 6dB, 20dB, 26dB and/or 99% signal bandwidth are measured using the bandwidths recommended by ANSI C6.10 and RSS GEN. Test Report R10161 Rev 1 Page 18

National Technical Systems - Silicon Valley SPECIFICATION LIMITS AND SAMPLE CALCULATIONS Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 The limits for conducted emissions are given in units of microvolts, and the limits for radiated emissions are given in units of microvolts per meter at a specified test distance. Data is measured in the logarithmic form of decibels relative to one microvolt, or db microvolts (dbuv). For radiated emissions, the measured data is converted to the field strength at the antenna in db microvolts per meter (dbuv/m). The results are then converted to the linear forms of uv and uv/m for comparison to published specifications. For reference, converting the specification limits from linear to decibel form is accomplished by taking the base ten logarithm, then multiplying by 20. These limits in both linear and logarithmic form are as follows: CONDUCTED EMISSIONS SPECIFICATION LIMITS: FCC 15.207; FCC 15.107(a), RSS GEN The table below shows the limits for the emissions on the AC power line from an intentional radiator and a receiver. Frequency (MHz) Average Limit (dbuv) Quasi Peak Limit (dbuv) 0.150 to 0.500 Linear decrease on logarithmic frequency axis between 56.0 and 6.0 Linear decrease on logarithmic frequency axis between 66.0 and 56.0 0.500 to 5.000 6.0 56.0 5.000 to 0.000 50.0 60.0 Test Report R10161 Rev 1 Page 19

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 GENERAL TRANSMITTER RADIATED EMISSIONS SPECIFICATION LIMITS The table below shows the limits for the spurious emissions from transmitters that fall in restricted bands 1. Frequency Limit Limit Range (uv/m) (dbuv/m @ m) (MHz) 0.009-0.90 200/F KHz @ 00m 67.6-20*log 10 (F KHz ) @ 00m 0.90-1.705 2000/F KHz @ 0m 87.6-20*log 10 (F KHz ) @ 0m 1.705 to 0 0 @ 0m 29.5 @ 0m 0 to 88 100 @ m 0 @ m 88 to 216 150 @ m.5 @ m 216 to 960 200 @ m 6.0 @ m Above 960 500 @ m 5.0 @ m FCC 15.07 (a) OUTPUT POWER LIMITS The table below shows the limits for output power and output power density. For the 5250-550 and 570-5725 MHz bands, where the signal bandwidth is less than 20 MHz the maximum output power is reduced to the power spectral density limit plus 10 times the log of the bandwidth (in MHz). Operating Frequency (MHz) Output Power Power Spectral Density 5150 5250 1Watt (0 dbm) 17 dbm/mhz 5250 550 and 570-5725 250 mw (2 dbm) 11 dbm/mhz 5725 5825 1 Watt (0 dbm) 0 dbm/500khz For system using antennas with gains exceeding 6dBi, the output power and power spectral density limits are reduced by 1dB for every db the antenna gain exceeds 6dBi. OUTPUT POWER LIMITS LELAN DEVICES The table below shows the limits for output power and output power density defined by RSS 27. Where the signal bandwidth is less than 20 MHz the maximum output power is reduced to the power spectral density limit plus 10 times the log of the bandwidth (in MHz). Operating Frequency Output Power Power Spectral Density (MHz) 5150 5250 200mW (2 dbm) eirp 10 dbm/mhz eirp 5250 550 and 570-5725 250 mw (2 dbm)2 1W (0dBm) eirp 11 dbm/mhz 5725 5825 1 Watt (0 dbm) W eirp 0 dbm/500khz 1 The restricted bands are detailed in FCC 15.205 and RSS-Gen Table 6 2 If EIRP exceeds 500mW the device must employ TPC Test Report R10161 Rev 1 Page 20

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 SPURIOUS EMISSIONS LIMITS UNII and LELAN DEVICES The spurious emissions limits for signals below 1GHz are the FCC/RSS-Gen general limits. For emissions above 1GHz, signals in restricted bands are subject to the FCC/RSS-Gen general limits. All other signals have a limit of 27dBm/MHz, which is field strength of 68.dBuV/m/MHz at a distance of m. For devices operating in the 5725-5850 MHz bands under the LELAN/UNII rules, the limit within 10MHz of the allocated band is increased to 17dBm/MHz. Test Report R10161 Rev 1 Page 21

National Technical Systems - Silicon Valley SAMPLE CALCULATIONS - CONDUCTED EMISSIONS Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 Receiver readings are compared directly to the conducted emissions specification limit (decibel form) as follows: R r - S = M where: R r = Receiver Reading in dbuv SAMPLE CALCULATIONS - RADIATED EMISSIONS S = Specification Limit in dbuv M = Margin to Specification in +/- db Receiver readings are compared directly to the specification limit (decibel form). The receiver internally corrects for cable loss, preamplifier gain, and antenna factor. The calculations are in the reverse direction of the actual signal flow, thus cable loss is added and the amplifier gain is subtracted. The Antenna Factor converts the voltage at the antenna coaxial connector to the field strength at the antenna elements. A distance factor, when used for electric field measurements above 0MHz, is calculated by using the following formula: Fd = 20*LOG10 (Dm/Ds) where: Fd = Distance Factor in db Dm = Measurement Distance in meters Ds = Specification Distance in meters For electric field measurements below 0MHz the extrapolation factor is either determined by making measurements at multiple distances or a theoretical value is calculated using the formula: Fd = 0*LOG10 (Dm/Ds) Measurement Distance is the distance at which the measurements were taken and Specification Distance is the distance at which the specification limits are based. The antenna factor converts the voltage at the antenna coaxial connector to the field strength at the antenna elements. The margin of a given emission peak relative to the limit is calculated as follows: Rc = Rr + Fd and M = Rc - Ls where: Rr = Receiver Reading in dbuv/m Fd = Distance Factor in db Rc = Corrected Reading in dbuv/m Ls = Specification Limit in dbuv/m M = Margin in db Relative to Spec Test Report R10161 Rev 1 Page 22

National Technical Systems - Silicon Valley SAMPLE CALCULATIONS - FIELD STRENGTH TO EIRP CONVERSION Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 Where the radiated electric field strength is expressed in terms of the equivalent isotropic radiated power (eirp), or where a field strength measurement of output power is made in lieu of a direct measurement, the following formula is used to convert between eirp and field strength at a distance of d (meters) from the equipment under test: E = 1000000 0 P microvolts per meter d where P is the eirp (Watts) For a measurement at m the conversion from a logarithmic value for field strength (dbuv/m) to an eirp power (dbm) is -95.dB. Test Report R10161 Rev 1 Page 2

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 Appendix A Test Equipment Calibration Data Radiated Emissions, 1,000-6,500 MHz, 05-May-16 Manufacturer Description Model Asset # Calibrated Cal Due Rohde & Schwarz EMI Test Receiver, 20 Hz-0 ESIB0 29 2/20/2016 2/20/2017 GHz (1088.790.0) EMCO Antenna, Horn, 1-18 GHz 115 27 11/18/201 11/18/2016 Radiated Emissions, 1,000-6,500 MHz, 06-May-16 Manufacturer Description Model Asset # Calibrated Cal Due EMCO Antenna, Horn, 1-18 GHz 115 1561 6/27/201 6/27/2016 Rohde & Schwarz EMI Test Receiver, 20 Hz-0 GHz ESIB0 (1088.790.0) 29 2/20/2016 2/20/2017 Radiated Emissions, 1,000-6,500 MHz, 10-May-16 Manufacturer Description Model Asset # Calibrated Cal Due EMCO Antenna, Horn, 1-18 GHz 115 87 7/29/201 7/29/2016 Rohde & Schwarz EMI Test Receiver, 20 Hz-7 GHz ESIB7 158 12/19/2015 12/19/2016 Radio Antenna Port (Power and Spurious Emissions), 10-May-16 Manufacturer Description Model Asset # Calibrated Cal Due Agilent Technologies PSA, Spectrum Analyzer, (installed options, 111, 115, 12, 1DS, B7J, HYX, E6A 219 6/22/2015 6/22/2016 Radio Antenna Port (Power and Spurious Emissions), 11-May-16 Manufacturer Description Model Asset # Calibrated Cal Due Agilent Technologies PSA, Spectrum Analyzer, (installed options, 111, 115, 12, 1DS, B7J, HYX, E6A 219 6/22/2015 6/22/2016 Test Report R10161 Rev 1 Page 2

National Technical Systems - Silicon Valley Project number JD9961 Report Date: May 16, 2016 Reissue Date: May 16, 2016 Appendix B Test Data T10155 Pages 26 116 Test Report R10161 Rev 1 Page 25

EMC Test Data Client: Aruba Networks Job Number: JD9961 Product APINH205 T-Log Number: T10155 System Configuration: - Contact: Rob Hastings Project Coordinator: - Emissions Standard(s): FCC 15.07 / RSS-210 Class: B Immunity Standard(s): - Environment: - EMC Test Data For The Aruba Networks Product APINH205 Date of Last Test: 5/10/2016 R10161 Rev 1 Cover Page 26

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 Date of Test: 5//2016 Test Engineer: Mark Hill Test Location: FT Lab # Duty cycle measurements performed on the worse case data rate for power (from original testing/filing) Notes: Measurements taken with maximum RBW/VBW settings allowed. Mode Data Rate Duty Cycle (x) Constant DC? T (ms) Pwr Cor Factor* Lin Volt Cor Factor** Min VBW for FS (Hz) 11a 6Mbs 0.99 Yes 2.1 0.0 0.0 10.0 n20 MCS8 0.98 Yes 1.0 0.1 0.2 10.0 n0 MCS0 0.96 Yes 0.5 0.2 0. 202. ac80 VHT0 0.9 Yes 0. 0. 0.6 921.6 * Correction factor when using RMS/Power averaging - 10*log(1/x) ** Correction factor when using linear voltage average - 20*log(1/x) T = Minimum transmission duration Duty Cycle R10161 Rev 1 Power & Duty Cycle Page 27

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 Power & Duty Cycle Page 28

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 Power & Duty Cycle Page 29

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Test Specific Details Objective: General Test Configuration Ambient Conditions: Temperature: 20-2 C Rel. Humidity: 0-7 % EMC Test Data Job Number: JD9961 T-Log Number: T10155 RSS-27 and FCC 15.07 (UNII) Radiated Spurious Emissions The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. The EUT and all local support equipment were located on the turntable for radiated spurious emissions testing. For radiated emissions testing the measurement antenna was located meters from the EUT, unless otherwise noted. R10161 Rev 1 UNII RE Page 0

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 Summary of Results Run # Mode Channel 11a operation 1 n20 operation 2 n0 operation ac80 operation a a a n20 n20 n20 n0 n0 ac80 6-5180MHz 0-5200MHz 8-520MHz 6-5180MHz 0-5200MHz 8-520MHz 8-5190MHz 6-520MHz 2-5210MHz Target Power Setting q72 q72 q72 q72 q72 q72 q65 q72 q5 Final Power Setting q68 q72 q60 q72 q72 q68 q60 q72 q5 Test Performed Limit Result / Margin Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E 5.8 dbµv/m @ 557.7 MHz (-0.2 db) 51. dbµv/m @ 5097. MHz (-2.6 db) 5.9 dbµv/m @ 599.0 MHz (-0.1 db) 9. dbµv/m @ 5107.6 MHz (-.7 db) 5.7 dbµv/m @ 558.6 MHz (-0. db) 5.9 dbµv/m @ 598.7 MHz (-0.1 db) 5.2 dbµv/m @ 519.2 MHz (-0.8 db) 52. dbµv/m @ 59. MHz (-1.6 db) 52.9 dbµv/m @ 518. MHz (-1.1 db) R10161 Rev 1 UNII RE Page 1

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 Summary of Results Run # Mode Channel 11a operation 5 n20 operation 6 n0 operation 7 ac80 operation a a a n20 n20 n20 n0 n0 8 ac80 52-5260MHz 60-500MHz 6-520MHz 52-5260MHz 60-500MHz 6-520MHz 5-5270MHz 62-510MHz 58-5290MHz Target Power Setting q71 q70 q69 q72 q72 q71 q72 q67 q58 Final Power Setting q58 q56 q69 q68 q6 q71 q72 q62 q56 Test Performed Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Radiated Emissions, 900-560MHz Limit FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E Result / Margin 5.8 dbµv/m @ 517.9 MHz (-0.2 db) 5.7 dbµv/m @ 557.7 MHz (-0. db) 52.8 dbµv/m @ 599.1 MHz (-1.2 db) 5.6 dbµv/m @ 521.5 MHz (-0. db) 5.7 dbµv/m @ 558.6 MHz (-0. db) 52.2 dbµv/m @ 501.5 MHz (-1.8 db) 5. dbµv/m @ 526. MHz (-0.6 db) 5.8 dbµv/m @ 551.5 MHz (-0.2 db) 5.7 dbµv/m @ 550.7 MHz (-0. db) R10161 Rev 1 UNII RE Page 2

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 Summary of Results Run # Mode Channel 11a operation 9 n20 operation 10 n0 operation 11 ac80 operation 12 a a a n20 n20 n20 n0 n0 ac80 ac80 100-5500MHz 116-5580MHz 10-5700MHz 100-5500MHz 116-5580MHz 10-5700MHz 102-5510MHz 110-5550MHz 106-550MHz 122-5610MHz Target Power Setting q68 q67 q69 q69 q69 q68 q67 q72 q55 q72 Final Power Setting q68 q67 q69 q69 q69 q68 q67 q72 q55 q72 Test Performed Limit Result / Margin Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz Radiated Emissions, 550-5900MHz FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E 51.1 dbµv/m @ 52.0 MHz (-2.9 db) 50.1 dbµv/m @ 518.9 MHz (-.9 db) 6.9 dbµv/m @ 5857.9 MHz (-. db) 8.5 dbµv/m @ 521.0 MHz (-5.5 db) 7.7 dbµv/m @ 522.5 MHz (-6. db) 65.7 dbµv/m @ 5861. MHz (-2.6 db) 50.8 dbµv/m @ 560.0 MHz (-.2 db) 9.0 dbµv/m @ 556.5 MHz (-5.0 db) 52.2 dbµv/m @ 559. MHz (-1.8 db) 9.9 dbµv/m @ 55.6 MHz (-.1 db) R10161 Rev 1 UNII RE Page

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 Summary of Results Run # Mode Channel 11a operation 1 n20 operation 1 n0 operation 15 ac80 operation a a a n20 n20 n20 n0 n0 16 ac80 19-575MHz 157-5785MHz 165-5825MHz 19-575MHz 157-5785MHz 165-5825MHz 151-5755MHz 159-5795MHz 155-5775MHz Target Power Setting q65 q70 q72 q65 q72 q72 q65 q72 q58 Final Power Setting q65 q70 q72 q65 q72 q72 q65 q72 q58 Test Performed Radiated Emissions, 5600-6000MHz Radiated Emissions, 5600-6000MHz Radiated Emissions, 5600-6000MHz Radiated Emissions, 5600-6000MHz Radiated Emissions, 5600-6000MHz Radiated Emissions, 5600-6000MHz Radiated Emissions, 5600-6000MHz Radiated Emissions, 5600-6000MHz Radiated Emissions, 5600-6000MHz Limit FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E FCC 15.209 / 15 E Result / Margin 6.2 dbµv/m @ 5902.9 MHz (-.1 db) 6.9 dbµv/m @ 596.8 MHz (-. db) 6.9 dbµv/m @ 5982.9 MHz (-. db) 6.2 dbµv/m @ 5902. MHz (-.1 db) 65. dbµv/m @ 592. MHz (-2.9 db) 6.5 dbµv/m @ 5991. MHz (-.8 db) 60.9 dbµv/m @ 5909.5 MHz (-7. db) 61. dbµv/m @ 597. MHz (-6.9 db) 59.2 dbµv/m @ 5926.7 MHz (-9.1 db) Modifications Made During Testing No modifications were made to the EUT during testing Deviations From The Standard No deviations were made from the requirements of the standard. Notes Testing limited in frequency based on the resutls from TCB audit testing. Tabular results represent the worse case (least margin) results observed. R10161 Rev 1 UNII RE Page

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Sample Notes Mode Data Rate Duty Cycle (x) Constant DC? T (ms) Pwr Cor Factor* Lin Volt Cor Factor** EMC Test Data Job Number: JD9961 T-Log Number: T10155 Procedure Comments: Measurements performed in accordance with FCC KDB 7890 Peak measurements performed with: RBW=1MHz, VBW=MHz, peak detector, max hold, auto sweep time Unless otherwise stated/noted, emission has duty cycle 98% and was measured using RBW=1MHz, VBW=10Hz, peak detector, linear average mode, auto sweep time, max hold 50 traces. (method VB of KDB 7890) Frequency range of investigation limited based on results observed during TCB audit. Min VBW for FS (Hz) 11a 6Mbs 99.0% Yes 2.1 0.0 0.0 10.0 n20 MCS8 97.9% Yes 1.0 0.1 0.2 10.0 n0 MCS0 96.% Yes 0.5 0.2 0. 202. ac80 VHT0 9.% Yes 0. 0. 0.6 921.6 Sample S/N: DN0010091 Driver: - Antenna: Internal Measurement Specific Notes: Note 1: Note : For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Per KDB 7890 2) c) (i), compliance can be demonstrated by meeting the average and peak limits of 15.209, as an alternative. Emission has constant duty cycle < 98%, average measurement performed: RBW=1MHz, VBW>1/T but not less than 10Hz, peak detector, linear averaging, auto sweep,max hold 50*1/DC traces (method VB of KDB 7890) R10161 Rev 1 UNII RE Page 5

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #1, Radiated Spurious Emissions, 900-560 MHz. Operation in the 5150-5250 MHz Band Date of Test: 05/05/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #1a: Low Channel Channel: 6 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 557.70 5.8 H 5.0-0.2 AVG 8 1. POS; RB 1 MHz; VB: 10 Hz q68 5097.0 51. H 5.0-2.6 AVG 8 1. POS; RB 1 MHz; VB: 10 Hz q72 519.920 6.6 V 5.0-7. AVG 9 2.5 POS; RB 1 MHz; VB: 10 Hz q72 516.950 6.6 H 5.0-7. AVG 5 1.0 POS; RB 1 MHz; VB: 10 Hz q72 517.760 65. H 7.0-8.6 PK 5 1.0 POS; RB 1 MHz; VB: MHz q72 519.600 6.2 V 7.0-9.8 PK 9 2.5 POS; RB 1 MHz; VB: MHz q72 562.0 6.7 H 7.0-10. PK 8 1. POS; RB 1 MHz; VB: MHz q68 5097.950 61. H 7.0-12.7 PK 8 1. POS; RB 1 MHz; VB: MHz q72 Run #1b: Center Channel Channel: 0 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5122.0 51. H 5.0-2.6 AVG 8 1. POS; RB 1 MHz; VB: 10 Hz 5118.500 51.0 V 5.0 -.0 AVG 21 2.2 POS; RB 1 MHz; VB: 10 Hz 5121.860 62.2 H 7.0-11.8 PK 8 1. POS; RB 1 MHz; VB: MHz 5122.0 61.6 V 7.0-12. PK 21 2.2 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 6

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #1c: High Channel Channel: 8 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 597.880 5.9 H 5.0-0.1 AVG 8 1. POS; RB 1 MHz; VB: 10 Hz q60 598.960 5.9 V 5.0-0.1 AVG 21 2.2 POS; RB 1 MHz; VB: 10 Hz q62 502.290 6. H 7.0-9.6 PK 8 1. POS; RB 1 MHz; VB: MHz q60 598.60 6.7 V 7.0-10. PK 21 2.2 POS; RB 1 MHz; VB: MHz q62 Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #2, Radiated Spurious Emissions, 900-560 MHz. Operation in the 5150-5250 MHz Band Date of Test: 05/05/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #2a: Low Channel Channel: 6 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5107.620 9. H 5.0 -.7 AVG 9 1. POS; RB 1 MHz; VB: 10 Hz 5107.620 7.7 V 5.0-6. AVG 12 2. POS; RB 1 MHz; VB: 10 Hz 516.20 6.9 H 7.0-9.1 PK 9 1. POS; RB 1 MHz; VB: MHz 5098.900 6. V 7.0-10.6 PK 12 2. POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 7

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #2b: Center Channel Date of Test: 05/05/16 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Channel: 0 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 558.620 5.7 H 5.0-0. AVG 6 1.2 POS; RB 1 MHz; VB: 10 Hz 558.660 5.6 V 5.0-0. AVG 5 1. POS; RB 1 MHz; VB: 10 Hz 55.810 6.5 H 7.0-9.5 PK 6 1.2 POS; RB 1 MHz; VB: MHz 556.970 6. V 7.0-9.7 PK 5 1. POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #2c: High Channel Channel: 8 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 598.670 5.9 H 5.0-0.1 AVG 7 1.2 POS; RB 1 MHz; VB: 10 Hz q68 598.690 5. V 5.0-0.6 AVG 20 2.2 POS; RB 1 MHz; VB: 10 Hz q72 502.270 65.1 H 7.0-8.9 PK 7 1.2 POS; RB 1 MHz; VB: MHz q68 501.550 6.8 V 7.0-10.2 PK 20 2.2 POS; RB 1 MHz; VB: MHz q72 Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 8

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #, Radiated Spurious Emissions, 900-560 MHz. Operation in the 5150-5250 MHz Band Date of Test: 05/05/16 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #a: Low Channel Channel: 8 Mode: n0 Tx Chain: 2Tx Data Rate: MCS0 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 519.160 5.2 H 5.0-0.8 Avg 08 1.2 POS; RB 1 MHz; VB: khz q60 519.560 66.8 H 7.0-7.2 PK 08 1.2 POS; RB 1 MHz; VB: MHz q60 519.970 52.5 V 5.0-1.5 Avg 12 2.5 POS; RB 1 MHz; VB: khz q60 519.00 66.6 V 7.0-7. PK 12 2.5 POS; RB 1 MHz; VB: MHz q60 Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 9

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #b: Center Channel Channel: 6 Mode: n0 Tx Chain: 2Tx Data Rate: MCS0 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 59.70 52. H 5.0-1.6 Avg 5 1.2 POS; RB 1 MHz; VB: khz 582.60 62. H 7.0-11.7 PK 5 1.2 POS; RB 1 MHz; VB: MHz 595.80 51. V 5.0-2.6 Avg 21 2. POS; RB 1 MHz; VB: khz 595.590 61.5 V 7.0-12.5 PK 21 2. POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #, Radiated Spurious Emissions, 900-560 MHz. Operation in the 5150-5250 MHz Band Date of Test: 05/05/16 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #a: Low Channel Channel: 2 Mode: ac80 Tx Chain: 2Tx Data Rate: VHT0 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 518.260 52.9 H 5.0-1.1 Avg 0 1. POS; RB 1 MHz; VB: 5 khz 519.60 65.2 H 7.0-8.8 PK 0 1. POS; RB 1 MHz; VB: MHz 51.710 51. V 5.0-2.6 Avg 18 2.1 POS; RB 1 MHz; VB: 5 khz 512.600 6.6 V 7.0-10. PK 18 2.1 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 0

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #5, Radiated Spurious Emissions, 900-560 MHz. Operation in the 5250-550 MHz Band Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #5a: Low Channel Channel: 52 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 517.860 5.8 H 5.0-0.2 AVG 8 1. POS; RB 1 MHz; VB: 10 Hz q58 519.060 52.5 V 5.0-1.5 AVG 15 2. POS; RB 1 MHz; VB: 10 Hz q58 517.50 6.8 H 7.0-10.2 PK 8 1. POS; RB 1 MHz; VB: MHz q58 52.10 62. V 7.0-11.6 PK 15 2. POS; RB 1 MHz; VB: MHz q58 Run #5b: Center Channel Channel: 60 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 557.700 5.7 H 5.0-0. AVG 5 1.5 POS; RB 1 MHz; VB: 10 Hz q56 559.060 52.8 V 5.0-1.2 AVG 15 2. POS; RB 1 MHz; VB: 10 Hz q56 557.600 6.7 H 7.0-10. PK 5 1.5 POS; RB 1 MHz; VB: MHz q56 559.220 6.1 V 7.0-10.9 PK 15 2. POS; RB 1 MHz; VB: MHz q56 Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 1

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #5c: High Channel Channel: 6 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 599.060 52.8 V 5.0-1.2 AVG 18 2. POS; RB 1 MHz; VB: 10 Hz 502.600 52.1 H 5.0-1.9 AVG 1. POS; RB 1 MHz; VB: 10 Hz 598.260 6.5 V 7.0-10.5 PK 18 2. POS; RB 1 MHz; VB: MHz 50.080 62. H 7.0-11.7 PK 1. POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #6, Radiated Spurious Emissions, 900-560 MHz. Operation in the 5250-550 MHz Band Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #6a: Low Channel Channel: 52 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 521.60 5.6 H 5.0-0. AVG 9 1. POS; RB 1 MHz; VB: 10 Hz q68 522.60 51.2 V 5.0-2.8 AVG 25 1.1 POS; RB 1 MHz; VB: 10 Hz q68 517.860 65. H 7.0-8.6 PK 9 1. POS; RB 1 MHz; VB: MHz q68 521.700 62.6 V 7.0-11. PK 25 1.1 POS; RB 1 MHz; VB: MHz q68 Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 2

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #6b: Center Channel Channel: 60 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 558.600 5.7 H 5.0-0. AVG 51 1. POS; RB 1 MHz; VB: 10 Hz q6 558.780 52.6 V 5.0-1. AVG 17 1.9 POS; RB 1 MHz; VB: 10 Hz q6 557.60 65. H 7.0-8.6 PK 51 1. POS; RB 1 MHz; VB: MHz q6 556.570 6.6 V 7.0-10. PK 17 1.9 POS; RB 1 MHz; VB: MHz q6 Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #6c: High Channel Channel: 6 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 501.60 52.2 H 5.0-1.8 AVG 51 1. POS; RB 1 MHz; VB: 10 Hz 500.990 7. V 5.0-6.7 AVG 1 1. POS; RB 1 MHz; VB: 10 Hz 597.700 6. H 7.0-9.7 PK 51 1. POS; RB 1 MHz; VB: MHz 50.800 59.8 V 7.0-1.2 PK 1 1. POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #7, Radiated Spurious Emissions, 900-560 MHz. Operation in the 5250-550 MHz Band Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #7a: Low Channel Channel: 5 Mode: n0 Tx Chain: 2Tx Data Rate: MCS0 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 526.270 5. H 5.0-0.6 AVG 57 1.2 POS; RB 1 MHz; VB: khz 52.950 51.9 V 5.0-2.1 AVG 1 2.5 POS; RB 1 MHz; VB: khz 526.510 6.1 H 7.0-10.9 PK 57 1.2 POS; RB 1 MHz; VB: MHz 55.190 61.2 V 7.0-12.8 PK 1 2.5 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #7b: Center Channel Channel: 62 Mode: n0 Tx Chain: 2Tx Data Rate: MCS0 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 551.50 5.8 H 5.0-0.2 AVG 2 1.2 POS; RB 1 MHz; VB: khz q62 552.20 69. H 7.0 -.6 PK 2 1.2 POS; RB 1 MHz; VB: MHz q62 550.000 8.2 V 5.0-5.8 AVG 18 1.0 POS; RB 1 MHz; VB: khz q62 550.660 6.2 V 7.0-10.8 PK 18 1.0 POS; RB 1 MHz; VB: MHz q62 Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #8, Radiated Spurious Emissions, 900-560 MHz. Operation in the 5250-550 MHz Band Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #8a: Low Channel Channel: 58 Mode: ac80 Tx Chain: 2Tx Data Rate: VHT0 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 550.660 5.7 H 5.0-0. AVG 7 1. POS; RB 1 MHz; VB: 5 khz q56 552.200 51.6 V 5.0-2. AVG 18 1.9 POS; RB 1 MHz; VB: 5 khz q56 55.50 67.8 H 7.0-6.2 PK 7 1. POS; RB 1 MHz; VB: MHz q56 552.200 6.8 V 7.0-9.2 PK 18 1.9 POS; RB 1 MHz; VB: MHz q56 Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 5

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #9, Radiated Spurious Emissions, 550-5900 MHz. Operation in the 570-5725 MHz Band Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #9a: Low Channel Channel: 100 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 522.950 51.1 H 5.0-2.9 AVG 6 1. POS; RB 1 MHz; VB: 10 Hz 522.970 6.2 V 5.0-7.8 AVG 15 1.2 POS; RB 1 MHz; VB: 10 Hz 517.900 61.7 H 7.0-12. PK 6 1. POS; RB 1 MHz; VB: MHz 51.270 57.8 V 7.0-16.2 PK 15 1.2 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #9b: Center Channel Channel: 116 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 518.860 50.1 H 5.0 -.9 AVG 2 1. POS; RB 1 MHz; VB: 10 Hz 52.950 6.8 V 5.0-7.2 AVG 18 2. POS; RB 1 MHz; VB: 10 Hz 518.180 61.0 H 7.0-1.0 PK 2 1. POS; RB 1 MHz; VB: MHz 51.610 58.9 V 7.0-15.1 PK 18 2. POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 6

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #9c: High Channel Channel: 10 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5857.900 6.9 H 68. -. PK 56 1. POS; RB 1 MHz; VB: MHz 559.10 5.8 H 5.0-8.2 AVG 56 1. POS; RB 1 MHz; VB: 10 Hz 55.650 57. H 7.0-16.6 PK 56 1. POS; RB 1 MHz; VB: MHz 586.0 6.1 V 68. -5.2 PK 19 2.1 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #10, Radiated Spurious Emissions, 550-5900 MHz. Operation in the 570-5725 MHz Band Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #10a: Low Channel Channel: 100 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 520.980 8.5 H 5.0-5.5 AVG 5 1.1 POS; RB 1 MHz; VB: 10 Hz 517.60 61. H 7.0-12.6 PK 5 1.1 POS; RB 1 MHz; VB: MHz 522.520 7.8 V 5.0-6.2 AVG 1 1.7 POS; RB 1 MHz; VB: 10 Hz 519.880 59. V 7.0-1.6 PK 1 1.7 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 7

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 Run #10b: Center Channel Channel: 116 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 522.50 7.7 H 5.0-6. AVG 0 1.0 POS; RB 1 MHz; VB: 10 Hz 527.760 59.0 H 7.0-15.0 PK 0 1.0 POS; RB 1 MHz; VB: MHz 521.60 5.0 V 5.0-9.0 AVG 189 1.9 POS; RB 1 MHz; VB: 10 Hz 5.510 57.2 V 7.0-16.8 PK 189 1.9 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #10c: High Channel Channel: 10 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5861.20 65.7 H 68. -2.6 PK 8 1.2 POS; RB 1 MHz; VB: MHz 585.10 62. V 68. -5.9 PK 22 1.0 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 8

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #11, Radiated Spurious Emissions, 550-5900 MHz. Operation in the 570-5725 MHz Band Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #11a: Low Channel Channel: 102 Mode: n0 Tx Chain: 2Tx Data Rate: MCS0 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 560.000 50.8 H 5.0 -.2 Avg 1. POS; RB 1 MHz; VB: khz 557.800 6.9 H 7.0-10.1 PK 1. POS; RB 1 MHz; VB: MHz 559.760 9.8 V 5.0 -.2 Avg 20 2.5 POS; RB 1 MHz; VB: khz 559.760 6.8 V 7.0-10.2 PK 20 2.5 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #11b: Center Channel Channel: 110 Mode: n0 Tx Chain: 2Tx Data Rate: MCS0 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 556.510 9.0 H 5.0-5.0 Avg 1.2 POS; RB 1 MHz; VB: khz 559.160 59.1 H 7.0-1.9 PK 1.2 POS; RB 1 MHz; VB: MHz 557.110 7.8 V 5.0-6.2 Avg 17 2.1 POS; RB 1 MHz; VB: khz 557.270 58.0 V 7.0-16.0 PK 17 2.1 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 9

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #12, Radiated Spurious Emissions, 550-5900 MHz. Operation in the570-5725 MHz Band Date of Test: 05/06/16 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: - Test Location: Chamber # EUT Voltage: 120V/ 60Hz Run #12a: Low Channel Channel: 106 Mode: ac80 Tx Chain: 2Tx Data Rate: VHT0 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 559.0 52.2 H 5.0-1.8 Avg 50 1. POS; RB 1 MHz; VB: 5 khz 552.500 6.1 H 7.0-9.9 PK 50 1. POS; RB 1 MHz; VB: MHz 558.60 50.6 V 5.0 -. Avg 18 1.7 POS; RB 1 MHz; VB: 5 khz 55.610 60.8 V 7.0-1.2 PK 18 1.7 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). Run #12a: Center Channel Channel: 122 Mode: ac80 Tx Chain: 2Tx Data Rate: VHT0 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 55.610 9.9 H 5.0 -.1 Avg 8 1. POS; RB 1 MHz; VB: 5 khz 556.910 61.6 H 7.0-12. PK 8 1. POS; RB 1 MHz; VB: MHz 55.90 7. V 5.0-6.6 Avg 17 2. POS; RB 1 MHz; VB: 5 khz 55.050 58.8 V 7.0-15.2 PK 17 2. POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 50

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #1, Radiated Spurious Emissions, 5600-6000 MHz. Operation in the 5725-5850 MHz Band Date of Test: 05/10/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber #7 EUT Voltage: 120V/ 60Hz Run #1a: Low Channel Channel: 19 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5902.900 6.2 H 68. -.1 PK 60 1. POS; RB 1 MHz; VB: MHz 5908.80 61. V 68. -6.9 PK 22 1.9 POS; RB 1 MHz; VB: MHz Run #1b: Center Channel Channel: 157 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 596.780 6.9 H 68. -. PK 60 1. POS; RB 1 MHz; VB: MHz 59.60 62.8 V 68. -5.5 PK 2 1.9 POS; RB 1 MHz; VB: MHz Run #1c: High Channel Channel: 165 Mode: a Tx Chain: 2Tx Data Rate: 6Mbs Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5982.900 6.9 H 68. -. PK 66 1. POS; RB 1 MHz; VB: MHz 598.020 62.2 V 68. -6.1 PK 21 1.9 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 51

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #1, Radiated Spurious Emissions, 5600-6000 MHz. Operation in the 5725-5850 MHz Band Date of Test: 05/10/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber #7 EUT Voltage: 120V/ 60Hz Run #1a: Low Channel Channel: 19 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5902.70 6.2 H 68. -.1 PK 68 1. POS; RB 1 MHz; VB: MHz 5902.70 61.8 V 68. -6.5 PK 2 1.9 POS; RB 1 MHz; VB: MHz Run #1b: Center Channel Channel: 157 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 592.70 65. H 68. -2.9 PK 68 1.2 POS; RB 1 MHz; VB: MHz 59.780 62. V 68. -5.9 PK 2 1.9 POS; RB 1 MHz; VB: MHz Run #1c: High Channel Channel: 165 Mode: n20 Tx Chain: 2Tx Data Rate: MCS8 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5991.0 6.5 H 68. -.8 PK 66 1.2 POS; RB 1 MHz; VB: MHz 5988.150 61.8 V 68. -6.5 PK 2 1.9 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 52

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #15, Radiated Spurious Emissions, 5600-6000 MHz. Operation in the 5725-5850 MHz Band Date of Test: 05/10/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber #7 EUT Voltage: 120V/ 60Hz Run #15a: Low Channel Channel: 151 Mode: n0 Tx Chain: 2Tx Data Rate: MCS0 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5909.510 60.9 H 68. -7. PK 60 1.2 POS; RB 1 MHz; VB: MHz 5911.50 59.1 V 68. -9.2 PK 2 1.9 POS; RB 1 MHz; VB: MHz Run #15b: Center Channel Channel: 159 Mode: n0 Tx Chain: 2Tx Data Rate: MCS0 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 597.20 61. H 68. -6.9 PK 55 1.1 POS; RB 1 MHz; VB: MHz 5958.10 59.6 V 68. -8.7 PK 22 2.2 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 5

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #16, Radiated Spurious Emissions, 5600-6000 MHz. Operation in the 5725-5850 MHz Band Date of Test: 05/10/16 Config. Used: 1 Test Engineer: Mehran Birgani Config Change: - Test Location: Chamber #7 EUT Voltage: 120V/ 60Hz Run #16a: Low Channel Channel: 155 Mode: ac80 Tx Chain: 2Tx Data Rate: VHT0 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Frequency Level Pol 15.209 / 15E Detector Azimuth Height Comments MHz db V/m v/h Limit Margin Pk/QP/Avg degrees meters 5926.70 59.2 H 68. -9.1 PK 5 1. POS; RB 1 MHz; VB: MHz 5907.020 57. V 68. -11.0 PK 27 2.2 POS; RB 1 MHz; VB: MHz Note 1: Note 2: For emissions in restricted bands, the limit of 15.209 was used which requires average and peak measurements. For emissions outside of the restricted bands the limit is -27dBm/MHz eirp (68.dBuV/m). The measurement method required is a peak measurement (RB=1MHz, VB MHz, peak detector). R10161 Rev 1 UNII RE Page 5

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - Test Specific Details Objective: Summary of Results RSS-27 (LELAN) and FCC 15.07(UNII) Antenna Port Measurements Power, PSD, Bandwidth and Spurious Emissions The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. Run # Test Performed Limit Pass / Fail Result / Margin a: 19.2dBm (82.6 mw) 1 Power, 5150-5250MHz 15.07(a) (1) (ii) Pass n20: 19.2dBm (8.5 mw) n0: 19.0dBm (80.1 mw) ac80: 1.9dBm (0.7 mw) 1 Power, 5150-5250MHz RSS-27 6.2.1 (1) Pass ac80: 1.9dBm (0.7 mw) 20.9dBm (0.12W) eirp General Test Configuration When measuring the conducted emissions from the EUT's antenna port, the antenna port of the EUT was connected to the spectrum analyzer or power meter via a suitable attenuator to prevent overloading the measurement system. All measurements are corrected to allow for the external attenuators and cables used. Ambient Conditions: Temperature: 22. C Rel. Humidity: 5 % Modifications Made During Testing No modifications were made to the EUT during testing Deviations From The Standard No deviations were made from the requirements of the standard. Notes Power measured for Canada only for those modes/channels where the power was lowered from the original filing. R10161 Rev 1 UNII-1 Ant (MIMO) Page 55

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - Procedure Comments: Measurements performed in accordance with FCC KDB 7890 D01 Sample Notes Sample S/N: - Driver: - Tab6- Ant 1 ( txchain 1) Tab5- Ant 2 ( txchain 2) Mode Data Rate Duty Cycle (x) Constant DC? T (ms) Pwr Cor Factor* Lin Volt Cor Factor** Min VBW for FS (Hz) 11a 6Mbs 0.99 Yes 2.06 0 0 10 n20 MCS8 0.98 Yes 0.98 0.09 0.18 10 n0 MCS0 0.96 Yes 0.9 0.16 0. 202 ac80 VHT0 0.9 Yes 0.255 0.0 0.59 922 R10161 Rev 1 UNII-1 Ant (MIMO) Page 56

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - Run #1: Bandwidth, Output Power and Power Spectral Density - MIMO Systems Date of Test: 5/10/2016 0:00 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: None Test Location: FT Lab #B EUT Voltage: 120V/60Hz Duty Cycle 98%. Output power measured using a spectrum analyzer (see plots below). RBW=1MHz, VB= MHz, Span > Note 1: OBW, # of points in sweep 2*span/RBW, auto sweep, RMS detector, power averaging on (transmitted signal was continuous, duty cycle 98%) and power integration over the OBW (method SA-1 of ANSI C6.10). Note 2: Measured using the same analyzer settings used for output power. For RSS-27 the limit for the 5150-5250 MHz band accounts for the antenna gain as the maximum eirp allowed is 10dBm/MHz. The limits are also corrected for instances where the highest measured value of the PSD exceeds the average Note : PSD (calculated from the measured power divided by the measured 99% bandwidth) by more than db by the amount that the measured value exceeds the average by more than db. 99% Bandwidth measured in accordance with C6.10 - RB between 1-5 % of OBW and VB *RB, Span between 1.5 and 5 Note : times OBW. For MIMO systems the total output power and total PSD are calculated from the sum of the powers of the individual chains (in linear terms). The antenna gain used to determine the EIRP and limits for PSD/Output power depends on the operating mode of the MIMO device. If the signals on the non-coherent between the transmit chains then the gain used to determine Note 5: the limits is the highest gain of the individual chains and the EIRP is the sum of the products of gain and power on each chain. If the signals are coherent then the effective antenna gain is the sum (in linear terms) of the gains for each chain and the EIRP is the product of the effective gain and total power. Antenna Gain Information Antenna Gain (dbi) / Chain Freq 1 2 5150-5250 6.0 6.0 No Yes Yes No 6.00 9.01 5250-550 6.0 6.0 No Yes Yes No 6.00 9.01 570-5725 6.0 6.0 No Yes Yes No 6.00 9.01 5725-5825 6.0 6.0 No Yes Yes No 6.00 9.01 BF MultiChain Legacy CDD Sectorized / Xpol Dir G (PWR) Dir G (PSD) For devices that support CDD modes Min # of spatial streams: 1 Max # of spatial streams: 2 R10161 Rev 1 UNII-1 Ant (MIMO) Page 57

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - Notes: Notes: Notes: Notes: BF = beamforming mode supported, Multichain Legacy = 802.11 legacy data rates supported for multichain transmissions, CDD = Cyclic Delay Diversity (or Cyclic Shift Diversity) modes supported, Sectorized / Xpol = antennas are sectorized or cross polarized. Dir G (PWR) = total gain (Gant + Array Gain) for power calculations; GA (PSD) = total gain for PSD calculations based on FCC KDB 662911. Depending on the modes supported, the Array Gain value for power could be different from the PSD value. Array gain for power/psd calculated per KDB 662911 D01. For systems with Beamforming and CDD, choose one the following options: Option 1: Delays are optimized for beamforming, rather than being selected from cyclic delay table of 802.11; Array gains calculated based on beamforming criteria. Option 2: Antennas are paired for beamforming, and the pairs are configured to use the cyclic delay diversity of 802.11; the array gain associated with beamforming with 2 antennas (db), and the array gain associated with CDD with two antennas (db for PSD and 0 db for power) FCC UNII-1 Limits Pwr PSD Outdoor AP 0 17 X Indoor AP 0 17 Station (e.g. Client) 2 11 Outdoor AP (>0 Elv.) 21 - R10161 Rev 1 UNII-1 Ant (MIMO) Page 58

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - MIMO Device - 5150-5250 MHz Band - FCC Mode: 11a Max EIRP (mw): 28.8652 Frequency Software 26dB BW Duty Cycle Power 1 Total Power FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) Result 1 15.2 5180 q68 99 68.6 18. 0.0 Pass 2 15.5 1 15.9 5200 q72 99 82.6 19.2 0.0 0.08 Pass 2 16. 1 1. 520 q60 99. 16.5 0.0 Pass 2 1.6 5150-5250 PSD - FCC Mode: 11a Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1. 5180 q68 99 5.8 7.6 1.0 Pass 2.8 1.9 5200 q72 99 6.6 8.2 1.0 Pass 2 5.5 1 2. 520 q60 99.6 5.6 1.0 Pass 2 2.8 R10161 Rev 1 UNII-1 Ant (MIMO) Page 59

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - R10161 Rev 1 UNII-1 Ant (MIMO) Page 60

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - MIMO Device - 5150-5250 MHz Band - FCC Mode: n20 Max EIRP (mw): 2.199 Frequency Software 26dB BW Duty Cycle Power 1 Total Power FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 15.8 5180 q72 98 81.7 19.1 0.0 2 16. 1 16.0 5200 q72 98 2 16. 1 15.1 520 q68 98 2 15.6 8.5 19.2 0.0 68.7 18. 0.0 0.08 Result Pass Pass Pass 5150-5250 PSD - FCC Mode: n20 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1.6 5180 q72 98 6.2 7.9 1.0 Pass 2 5.2 1.9 5200 q72 98 6.5 8.1 1.0 Pass 2 5. 1.8 520 q68 98 5.2 7.2 1.0 Pass 2.5 R10161 Rev 1 UNII-1 Ant (MIMO) Page 61

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - R10161 Rev 1 UNII-1 Ant (MIMO) Page 62

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - MIMO Device - 5150-5250 MHz Band - FCC Mode: n0 Max EIRP (mw): 18.888 Frequency Software 26dB BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 1.2 5190 q60 96.5 16. 0.0 2 1.2 0.080 1 15.8 520 q72 96 80.1 19.0 0.0 2 15.9 Result Pass Pass 5150-5250 PSD - FCC Mode: n0 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz 1-1.2 5190 q60 96 1.6 2.0 2-0.9 1 1.5 520 q72 96.0.8 2 1.7 FCC Limit dbm/mhz Result 1.0 Pass 1.0 Pass R10161 Rev 1 UNII-1 Ant (MIMO) Page 6

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - R10161 Rev 1 UNII-1 Ant (MIMO) Page 6

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - MIMO Device - 5150-5250 MHz Band - FCC Mode: ac80 Max EIRP (mw): 122.2189 Frequency Software 26dB BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain Result (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 11. 5210 q5 9 0.7 1.9 0.0 0.01 Pass 2 11.7 MIMO Device - 5150-5250 MHz Band - Industry Canada Mode: ac80 Max EIRP (mw): 12.0 Frequency Software 99% BW Duty Cycle Power 1 Total Power IC limit Max Power Chain Result (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm (eirp) (W) 1 11. 5210 q5 75.6 9 1.9 20.9 2.0 0.01 Pass 2 11.7 5150-5250 PSD - FCC Mode: ac80 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz 1-5.7 5210 q5 9 0.6-2.2 1.0 2-5.5 Result Pass 5150-5250 PSD - IC Mode: ac80 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz 1-5.7 5210 q5 9 0.6-2.2 2-5.5 IC Limit dbm/mhz Result 1.0 Pass R10161 Rev 1 UNII-1 Ant (MIMO) Page 65

EMC Test Data Client: Aruba Networks Contact: Rob Hastings Standard: FCC 15.07 / RSS-210 Job Number: JD9961 T-Log Number: T10155 Project Coordinator: - R10161 Rev 1 UNII-1 Ant (MIMO) Page 66

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Test Specific Details Objective: RSS-27 (LELAN) and FCC 15.07(UNII) Antenna Port Measurements Power, PSD, Bandwidth and Spurious Emissions EMC Test Data Job Number: JD9961 T-Log Number: T10155 The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. Summary of Results Run # Test Performed Limit 1 Power, 5250-550MHz 1 Max EIRP 5250-550MHz 15.07(a) (2) RSS-27 6.2.2 (1) TPC required if EIRP 500mW (27dBm). EIRP 200mW (2dBm) DFS threshold = -6dBm. Pass / Fail Result / Margin a: 18.7dBm (7.1 mw) n20: 18.9dBm (77.6 mw) Pass n0: 18.7dBm (7.1 mw) ac80: 15.6dBm (6.5 mw) Pass EIRP = 2.9 dbm (06.5 mw) General Test Configuration When measuring the conducted emissions from the EUT's antenna port, the antenna port of the EUT was connected to the spectrum analyzer or power meter via a suitable attenuator to prevent overloading the measurement system. All measurements are corrected to allow for the external attenuators and cables used. Ambient Conditions: Temperature: 22. C Rel. Humidity: 5 % R10161 Rev 1 UNII-2A Ant (MIMO) Page 67

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Modifications Made During Testing No modifications were made to the EUT during testing Deviations From The Standard No deviations were made from the requirements of the standard. EMC Test Data Job Number: JD9961 T-Log Number: T10155 Procedure Comments: Measurements performed in accordance with FCC KDB 7890 D01 Sample Notes Sample S/N: - Driver: - Tab6- Ant 1 ( txchain 1) Tab5- Ant 2 ( txchain 2) Mode Data Rate Duty Cycle (x) Constant DC? T (ms) Pwr Cor Factor* Lin Volt Cor Factor** Min VBW for FS (Hz) 11a 6Mbs 0.99 Yes 2.06 0 0 10 n20 MCS8 0.98 Yes 0.98 0.09 0.18 10 n0 MCS0 0.96 Yes 0.9 0.16 0. 202 ac80 VHT0 0.9 Yes 0.255 0.0 0.59 922 R10161 Rev 1 UNII-2A Ant (MIMO) Page 68

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #1: Bandwidth, Output Power and Power Spectral Density - MIMO Systems Date of Test: 5/10/2016 0:00 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: None Test Location: FT Lab #B EUT Voltage: 120V/60Hz Antenna Gain Information Antenna Gain (dbi) / Chain Freq 1 2 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Duty Cycle 98%. Output power measured using a spectrum analyzer (see plots below). RBW=1MHz, VB= MHz, Span > Note 1: OBW, # of points in sweep 2*span/RBW, auto sweep, RMS detector, power averaging on (transmitted signal was continuous, duty cycle 98%) and power integration over the OBW (method SA-1 of ANSI C6.10). Note 2: Measured using the same analyzer settings used for output power. 99% Bandwidth measured in accordance with C6.10 - RB between 1-5 % of OBW and VB *RB, Span between 1.5 and 5 Note : times OBW. For MIMO systems the total output power and total PSD are calculated from the sum of the powers of the individual chains (in linear terms). The antenna gain used to determine the EIRP and limits for PSD/Output power depends on the operating mode of the MIMO device. If the signals on the non-coherent between the transmit chains then the gain used to determine Note : the limits is the highest gain of the individual chains and the EIRP is the sum of the products of gain and power on each chain. If the signals are coherent then the effective antenna gain is the sum (in linear terms) of the gains for each chain and the EIRP is the product of the effective gain and total power. 5150-5250 6.0 6.0 No Yes Yes No 6.00 9.01 5250-550 6.0 6.0 No Yes Yes No 6.00 9.01 570-5725 6.0 6.0 No Yes Yes No 6.00 9.01 5725-5825 6.0 6.0 No Yes Yes No 6.00 9.01 BF MultiChain Legacy CDD Sectorized / Xpol Dir G (PWR) Dir G (PSD) R10161 Rev 1 UNII-2A Ant (MIMO) Page 69

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 For devices that support CDD modes Min # of spatial streams: 1 Max # of spatial streams: 2 Notes: Notes: Notes: Notes: BF = beamforming mode supported, Multichain Legacy = 802.11 legacy data rates supported for multichain transmissions, CDD = Cyclic Delay Diversity (or Cyclic Shift Diversity) modes supported, Sectorized / Xpol = antennas are sectorized or cross polarized. Dir G (PWR) = total gain (Gant + Array Gain) for power calculations; GA (PSD) = total gain for PSD calculations based on FCC KDB 662911. Depending on the modes supported, the Array Gain value for power could be different from the PSD value. Array gain for power/psd calculated per KDB 662911 D01. For systems with Beamforming and CDD, choose one the following options: Option 1: Delays are optimized for beamforming, rather than being selected from cyclic delay table of 802.11; Array gains calculated based on beamforming criteria. Option 2: Antennas are paired for beamforming, and the pairs are configured to use the cyclic delay diversity of 802.11; the array gain associated with beamforming with 2 antennas (db), and the array gain associated with CDD with two antennas (db for PSD and 0 db for power) R10161 Rev 1 UNII-2A Ant (MIMO) Page 70

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 5250-550 MHz Band - FCC Mode: 11a Max EIRP (mw): 292.6 Frequency Software 26dB BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) Result 1 12. 5260 q58 20. 99 6. 15.6 2.0 Pass 2 12.8 1 12.1 500 q56 20.2 99.8 15. 2.0 0.07 Pass 2 12.7 1 15.5 520 q69 20.6 99 7.5 18.7 2.0 Pass 2 15.8 MIMO Device - 5250-550 MHz Band - Industry Canada Mode: 11a Frequency Software 99% BW Duty Cycle Power 1 Total Power IC limit Max Power Chain (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm (W) Result 1 12. 5260 q58 16.8 99 15.6 21.6 2. Pass 2 12.8 1 12.1 500 q56 16.8 99 15. 21. 2. 0.07 Pass 2 12.7 1 15.5 520 q69 16.8 99 18.7 2.7 2. Pass 2 15.8 R10161 Rev 1 UNII-2A Ant (MIMO) Page 71

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 5250-550 PSD - FCC/IC Mode: 11a Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1 1. 5260 q58 99.0.8 8.0 11.0 Pass 2 2.1 1 1.2 500 q56 99 2.8.5 8.0 11.0 Pass 2 1.8 1.6 520 q69 99 6.0 7.8 8.0 11.0 Pass 2.9 R10161 Rev 1 UNII-2A Ant (MIMO) Page 72

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2A Ant (MIMO) Page 7

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 MIMO Device - 5250-550 MHz Band - FCC Mode: n20 Max EIRP (mw): 06.5 Frequency Software 26dB BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 1.7 5260 q68 20.7 98 61.1 17.9 2.0 2 15.0 1 1.7 500 q6 20. 98 5.0 17.2 2.0 0.077 2 1.7 1 15.8 520 q69 20. 98 76.9 18.9 2.0 2 15.9 Result Pass Pass Pass MIMO Device - 5250-550 MHz Band - Industry Canada Mode: n20 Frequency Software 99% BW Duty Cycle Power 1 Total Power IC limit Chain (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm 1 1.7 5260 q68 18.0 98 17.9 2.9 2.6 2 15.0 1 1.7 500 q6 17.7 98 17.2 2.2 2 1.7 1 15.8 520 q69 20. 98 2 15.9 18.9 2.9 Max Power (W) Result Pass 2.5 0.077 Pass 2.0 Pass R10161 Rev 1 UNII-2A Ant (MIMO) Page 7

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 5250-550 PSD - FCC/IC Mode: n20 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1.5 5260 q68 98.6 6.6 8.0 11.0 Pass 2.7 1-2.5 500 q6 98 1. 1.1 8.0 11.0 Pass 2-1. 1.8 520 q69 98 6.0 7.8 8.0 11.0 Pass 2.7 R10161 Rev 1 UNII-2A Ant (MIMO) Page 75

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2A Ant (MIMO) Page 76

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 MIMO Device - 5250-550 MHz Band - FCC Mode: n0 Max EIRP (mw): 29.2 Frequency Software 26dB BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 15. 5270 q72 0 96 7.9 18.7 2.0 2 15.6 0.07 1 1.5 510 q62 9. 96 8.9 16.9 2.0 2 1.9 Result Pass Pass MIMO Device - 5250-550 MHz Band - Industry Canada Mode: n0 Frequency Software 99% BW Duty Cycle Power 1 Total Power IC limit Chain (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm 1 15. 5270 q72 6.7 96 18.7 2.7 2.0 2 15.6 1 1.5 510 q62 6. 96 16.9 22.9 2.0 2 1.9 Max Power (W) 0.07 Result Pass Pass MIMO Device 5250-550 PSD - FCC/IC Mode: n0 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1 1.1 5270 q72 96 2.8.5 8.0 11.0 Pass 2 1. 1-0.8 510 q62 96 1.8 2.6 8.0 11.0 Pass 2-0. R10161 Rev 1 UNII-2A Ant (MIMO) Page 77

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2A Ant (MIMO) Page 78

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 5250-550 MHz Band - FCC Mode: ac80 Max EIRP (mw): 15. Frequency Software 26dB BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain Result (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 12.2 5290 q56 8 9 6.5 15.6 2.0 0.07 Pass 2 12. MIMO Device - 5250-550 MHz Band - Industry Canada Mode: ac80 Frequency Software 99% BW Duty Cycle Power 1 Total Power IC limit Chain (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm 1 12.2 5290 15.6 21.6 2 12. Max Power (W) Result q56 75.87 9 2.0 0.06 Pass MIMO Device 5250-550 PSD - FCC/IC Mode: ac80 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC Limit Chain Result (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz 1 -.8 5290 q56 9 0.7-1.5 8.0 11.0 Pass 2 -.6 R10161 Rev 1 UNII-2A Ant (MIMO) Page 79

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2A Ant (MIMO) Page 80

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Test Specific Details Objective: Summary of Results Run # Test Performed Limit Pass / Fail Result / Margin General Test Configuration RSS-27 (LELAN) and FCC 15.07(UNII) Antenna Port Measurements Power, PSD, Bandwidth and Spurious Emissions Pass Pass EMC Test Data Job Number: JD9961 T-Log Number: T10155 The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. 1 Power, 570-5725MHz 15.07(a) (1), (2) 1 Max EIRP 570-5725MHz TPC required if EIRP 500mW (27dBm). EIRP 200mW (2dBm) DFS threshold a: 18.dBm (67.8mW) n20: 18.dBm (69.0 mw) n0: 19.1dBm (81.0 mw) ac80: 19.5dBm (88.6 mw) EIRP = 25.5 dbm (52.7 mw) When measuring the conducted emissions from the EUT's antenna port, the antenna port of the EUT was connected to the spectrum analyzer or power meter via a suitable attenuator to prevent overloading the measurement system. All measurements are corrected to allow for the external attenuators and cables used. Ambient Conditions: Temperature: 22. C Rel. Humidity: 5 % Modifications Made During Testing No modifications were made to the EUT during testing Deviations From The Standard No deviations were made from the requirements of the standard. R10161 Rev 1 UNII-2C Ant (MIMO) Page 81

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Procedure Comments: Measurements performed in accordance with FCC KDB 7890 D01 Sample Notes Sample S/N: - Driver: - Tab6- Ant 1 ( txchain 1) Tab5- Ant 2 ( txchain 2) Mode Data Rate Duty Cycle (x) Constant DC? T (ms) Pwr Cor Factor* Lin Volt Cor Factor** EMC Test Data Job Number: JD9961 T-Log Number: T10155 Min VBW for FS (Hz) 11a 6Mbs 99% Yes 2.06 0 0 10 n20 MCS8 98% Yes 0.98 0.09 0.18 10 n0 MCS0 96% Yes 0.9 0.16 0. 202 ac80 VHT0 9% Yes 0.255 0.0 0.59 922 R10161 Rev 1 UNII-2C Ant (MIMO) Page 82

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Run #1: Bandwidth, Output Power and Power Spectral Density - MIMO Systems Date of Test: 5/10/2016 0:00 Config. Used: 1 Test Engineer: Rafael Varelas Config Change: None Test Location: FT Lab #B EUT Voltage: 120V/60Hz Antenna Gain Information Antenna Gain (dbi) / Chain Freq 1 2 EMC Test Data Job Number: JD9961 T-Log Number: T10155 Duty Cycle 98%. Output power measured using a spectrum analyzer (see plots below). RBW=1MHz, VB= MHz, Span > Note 1: OBW, # of points in sweep 2*span/RBW, auto sweep, RMS detector, power averaging on (transmitted signal was continuous, duty cycle 98%) and power integration over the OBW (method SA-1 of ANSI C6.10). Note 2: Measured using the same analyzer settings used for output power. 99% Bandwidth measured in accordance with C6.10 - RB between 1-5 % of OBW and VB *RB, Span between 1.5 and 5 Note : times OBW. For MIMO systems the total output power and total PSD are calculated from the sum of the powers of the individual chains (in linear terms). The antenna gain used to determine the EIRP and limits for PSD/Output power depends on the operating mode of the MIMO device. If the signals on the non-coherent between the transmit chains then the gain used to determine Note : the limits is the highest gain of the individual chains and the EIRP is the sum of the products of gain and power on each chain. If the signals are coherent then the effective antenna gain is the sum (in linear terms) of the gains for each chain and the EIRP is the product of the effective gain and total power. 5150-5250 6.0 6.0 No Yes Yes No 6.00 9.01 5250-550 6.0 6.0 No Yes Yes No 6.00 9.01 570-5725 6.0 6.0 No Yes Yes No 6.00 9.01 5725-5825 6.0 6.0 No Yes Yes No 6.00 9.01 BF MultiChain Legacy CDD Sectorized / Xpol Dir G (PWR) Dir G (PSD) For devices that support CDD modes Min # of spatial streams: 1 Max # of spatial streams: 2 R10161 Rev 1 UNII-2C Ant (MIMO) Page 8

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 Notes: Notes: Notes: Notes: BF = beamforming mode supported, Multichain Legacy = 802.11 legacy data rates supported for multichain transmissions, CDD = Cyclic Delay Diversity (or Cyclic Shift Diversity) modes supported, Sectorized / Xpol = antennas are sectorized or cross polarized. Dir G (PWR) = total gain (Gant + Array Gain) for power calculations; GA (PSD) = total gain for PSD calculations based on FCC KDB 662911. Depending on the modes supported, the Array Gain value for power could be different from the PSD value. Array gain for power/psd calculated per KDB 662911 D01. For systems with Beamforming and CDD, choose one the following options: Option 1: Delays are optimized for beamforming, rather than being selected from cyclic delay table of 802.11; Array gains calculated based on beamforming criteria. Option 2: Antennas are paired for beamforming, and the pairs are configured to use the cyclic delay diversity of 802.11; the array gain associated with beamforming with 2 antennas (db), and the array gain associated with CDD with two antennas (db for PSD and 0 db for power) R10161 Rev 1 UNII-2C Ant (MIMO) Page 8

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 570-5725 MHz Band - FCC Mode: 11a Max EIRP (mw): 269.9 Frequency Software 26dB BW Duty Cycle Power Total Power FCC Limit Max Power Chain Result (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 15.2 5500 q68 20. 99 67.8 18. 2.0 Pass 2 15. 1 1.7 5580 q67 20. 99 61.9 17.9 2.0 Pass 2 15.1 0.068 1 15.2 5700 q68 20.5 99 67.0 18. 2.0 Pass 2 15. 1 1.0 5720 q65 15.2 99 52.0 17.2 22.8 Pass 2 1. Portion within 5725-5850 MHz band (UNII-) 1 7.8 5720 q65 99 11.9 10.8 0.0 0.0119 Pass 2 7.7 R10161 Rev 1 UNII-2C Ant (MIMO) Page 85

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 570-5725 MHz Band - Industry Canada Mode: 11a Frequency Software 99% BW Duty Cycle Power 1 Total Power IC Limit Chain (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm 1 15.2 5500 q68 16.9 99 18. 2. 2. 2 15. 1 1.7 5580 q67 16.8 99 2 15.1 1 15.2 5700 q68 16.8 99 18. 2. 2 15. 1 1.0 5720 q65 1.52 99 2 1. 17.9 2.9 2. Max Power (W) 2. Pass Portion within 5725-5850 MHz band (UNII-) 1 7.8 5720 q65 99 10.8 16.8 0.0 0.012 Pass 2 7.7 0.068 Result Pass Pass 17.2 2.2 22. Pass R10161 Rev 1 UNII-2C Ant (MIMO) Page 86

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 570-5700 PSD - FCC/IC Mode: 11a Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1. 5500 q68 99 5.6 7.5 8.0 11.0 Pass 2.5 1.2 5580 q67 99 5. 7.2 8.0 11.0 Pass 2. 1. 5700 q68 99 5.6 7.5 8.0 11.0 Pass 2.7 1. 5720 q65 99 5.6 7.5 8.0 11.0 Pass 2.6 Portion within 5725-5850 MHz band (UNII-) 1. 5720 q65 99.5 6.5 27.0 27.0 Pass 2.8 R10161 Rev 1 UNII-2C Ant (MIMO) Page 87

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 88

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 89

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 90

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 570-5725 MHz Band - FCC Mode: n20 Max EIRP (mw): 27.1 Frequency Software 26dB BW Duty Cycle Power Total Power FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 15. 5500 q69 20.6 98 68.6 18. 2.0 2 15. 1 15.1 5580 q69 22.9 98 2 15. 1 15.1 5700 q68 20.5 98 5720 2 15. 1 1.5 q68 15. 98 2 1.9 67.0 18. 59.1 17.7 2.0 66.2 18.2 2.0 0.069 Result Pass Pass Pass 22.9 Pass Portion within 5725-5850 MHz band (UNII-) 1 8.8 5720 q68 98 11.9 17.9 0.0 0.015 2 9.0 Pass R10161 Rev 1 UNII-2C Ant (MIMO) Page 91

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 570-5725 MHz Band - Industry Canada Mode: n20 Frequency Software 99% BW Duty Cycle Power 1 Total Power IC Limit Chain (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm 1 15. 5500 q69 17.97 98 18. 2. 2.5 2 15. 1 15.1 5580 5720 q69 17.97 98 2 15. 1 15.1 5700 q68 17.97 98 2 15. 1 1.5 q68 1.1 98 2 1.9 18. 2. 2.5 18.2 2.2 17.7 2.7 2.5 Max Power (W) 0.069 Result Pass Pass Pass 22.5 Pass Portion within 5725-5850 MHz band (UNII-) 1 8.8 5720 q68 98 2 9.0 11.9 17.9 0.0 0.0119 Pass R10161 Rev 1 UNII-2C Ant (MIMO) Page 92

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 570-5725 PSD - FCC/IC Mode: n20 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1.0 5500 q69 98 5.2 7.2 8.0 11.0 Pass 2. 1.8 5580 q69 98 5.2 7.2 8.0 11.0 Pass 2. 1.9 5700 q68 98 5.1 7.1 8.0 11.0 Pass 2.2 1. 5720 q68 98 5.7 7.6 8.0 11.0 Pass 2.8 Portion within 5725-5850 MHz band (UNII-) 1.8 5720 q68 98.9 6.9 27.0 2.9 27.0 Pass R10161 Rev 1 UNII-2C Ant (MIMO) Page 9

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 9

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 95

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 96

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 570-5725 MHz Band - FCC Mode: n0 Max EIRP (mw): 22.9 Frequency Software 26dB BW Duty Cycle Power Total Power FCC Limit Max Power Chain Result (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 1.5 5510 q67 0. 96 59. 17.7 2.0 Pass 2 1.6 1 15.5 5550 q72 0.1 96 7.1 18.6 2.0 Pass 2 15. 0.081 1 15.5 5670 q72 9.6 96 76.6 18.8 2.0 Pass 2 15.8 1 15.8 5710 q72.9 96 81.1 19.1 2.0 Pass 2 16.0 Portion within 5725-5850 MHz band (UNII-) 1 5.6 5710 q72 96 7.7 8.9 2 5.7 0.0 0.0077 Pass R10161 Rev 1 UNII-2C Ant (MIMO) Page 97

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 570-5725 MHz Band - Industry Canada Mode: n0 Frequency Software 99% BW Duty Cycle Power 1 Total Power IC Limit Chain (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm 1 1.5 5510 q67 6. 96 17.7 2.7 2.0 2 1.6 1 15.5 5550 q72 6.7 96 18.6 2.6 2.0 2 15. 1 15.5 5670 q72 6.7 96 18.8 2.8 2.0 2 15.8 1 15.8 5710 q72.2 96 19.1 25.1 2 16.0 Max Power (W) Portion within 5725-5850 MHz band (UNII-) 1 5.6 5710 q72 96 8.8 1.8 0.0 0.008 Pass 2 5.7 0.081 Result Pass Pass Pass 2.0 Pass R10161 Rev 1 UNII-2C Ant (MIMO) Page 98

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device 570-5725 PSD - FCC/IC Mode: n0 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1 0. 5510 q67 96 2..8 8.0 11.0 Pass 2 0.7 1 1.2 5550 q72 96 2.8.5 8.0 11.0 Pass 2 1. 1 1.2 5670 q72 96 2.8.5 8.0 11.0 Pass 2 1.5 1 1.9 5710 q72 96. 5.2 8.0 11.0 Pass 2 2.2 Portion within 5725-5850 MHz band (UNII-) 1 1.6 5710 q72 96.0.8 27.0 27.0 Pass 2 1.5 R10161 Rev 1 UNII-2C Ant (MIMO) Page 99

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 100

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 101

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 570-5725 MHz Band - FCC Mode: ac80 Max EIRP (mw): 52.7 Frequency Software 26dB BW Duty Cycle Power 1 Total Power FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) Result 1 11.7 550 q55 81. 9 2.6 15.1 2.0 Pass 2 11.9 1 15.7 5610 q72 85.9 9 8.8 19.2 2.0 0.089 Pass 2 16.1 1 16.1 5690 q72 80. 9 88.6 19.5 2.0 Pass 2 16.2 Portion within 5725-5850 MHz band (UNII-) 1 2.2 5690 q72 9.5 5. 0.0 0.005 Pass 2 2.0 R10161 Rev 1 UNII-2C Ant (MIMO) Page 102

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 570-5725 MHz Band - Industry Canada Mode: ac80 Frequency Software 99% BW Duty Cycle Power 1 Total Power IC Limit Max Power Chain Result (MHz) Setting (MHz) % dbm dbm dbm (eirp) dbm (W) 1 11.7 550 q55 75.87 9 15.1 21.1 2.0 Pass 2 11.9 0.089 1 16.1 5690 q72 72.7 9 19.5 25.5 2.0 Pass 2 16.2 Portion within 5725-5850 MHz band (UNII-) 1 2.2 5690 q72 9 2 2.0 5. 11. 0.0 0.00 Pass R10161 Rev 1 UNII-2C Ant (MIMO) Page 10

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 570-5725 PSD - FCC/IC Note: 5610 MHz channel not used for Canada Mode: ac80 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1-5.8 550 q55 9 0.6-2.2 8.0 11.0 Pass 2-5.5 1-1.6 5610 q72 2-1.1 1-0.9 9 2-0.8 5690 q72 9 1.6 2.0 Portion within 5725-5850 MHz band (UNII-) 1-2.1 5690 q72 9 1. 1.1 27.0 27.0 Pass 2-2.1 1.8 8.0 - Pass 2.6 8.0 11.0 Pass R10161 Rev 1 UNII-2C Ant (MIMO) Page 10

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 105

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII-2C Ant (MIMO) Page 106

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Test Specific Details Objective: Summary of Results Run # Test Performed Limit Pass / Fail Result / Margin General Test Configuration RSS-27 (LELAN) and FCC 15.07(UNII) Antenna Port Measurements Power, PSD, Bandwidth and Spurious Emissions Ambient Conditions: Temperature: 20-22 C Rel. Humidity: 0-5 % Pass EMC Test Data Job Number: JD9961 T-Log Number: T10155 The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. 1 Power, 5725-5850MHz Deviations From The Standard No deviations were made from the requirements of the standard. 15.07(a)() RSS-27 6.2.(1) a: 19.dBm (85. mw) n20: 19.5dBm (88. mw) n0: 19.dBm (87.9 mw) ac80: 16.2dBm (1.9 mw) When measuring the conducted emissions from the EUT's antenna port, the antenna port of the EUT was connected to the spectrum analyzer or power meter via a suitable attenuator to prevent overloading the measurement system. All measurements are corrected to allow for the external attenuators and cables used. Modifications Made During Testing No modifications were made to the EUT during testing R10161 Rev 1 UNII- Ant (MIMO) Page 107

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Procedure Comments: Measurements performed in accordance with FCC KDB 7890 D01 Sample Notes Sample S/N: Driver: Note 1: Note 2: Note : Note : Mode Data Rate Duty Cycle (x) Constant DC? T (ms) Pwr Cor Factor* Lin Volt Cor Factor** EMC Test Data Job Number: JD9961 T-Log Number: T10155 Min VBW for FS (Hz) 11a 6Mbs 99% Yes 2.06 0 0 10 n20 MCS8 98% Yes 0.98 0.09 0.18 10 n0 MCS0 96% Yes 0.9 0.16 0. 202 ac80 VHT0 9% Yes 0.255 0.0 0.59 922 Duty Cycle 98%. Output power measured using a spectrum analyzer (see plots below). RBW=1MHz, VB= MHz, Span > OBW, # of points in sweep 2*span/RBW, auto sweep, RMS detector, power averaging on (transmitted signal was continuous, duty cycle 98%) and power integration over the OBW (method SA-1 of ANSI C6.10). Duty Cycle < 98%. Output power measured using a spectrum analyzer (see plots below). RBW=1MHz, VB= MHz, Span > OBW, # of points in sweep 2*span/RBW, auto sweep, RMS detector, power averaging on (transmitted signal was not continuous, but the analyzer was configured to trigger only on full power pulses such that the analyzer was only sweeping when the device was transmitting) and power integration over the OBW (method SA-1 of ANSI C6.10). Measured using the same analyzer settings used for output power. 99% Bandwidth measured in accordance with C6.10 - RB between 1-5 % of OBW and VB *RB, Span between 1.5 and 5 times OBW. For MIMO systems the total output power and total PSD are calculated from the sum of the powers of the individual chains (in linear terms). The antenna gain used to determine the EIRP and limits for PSD/Output power depends on the operating mode of the MIMO device. If the signals on the non-coherent between the transmit chains then the gain used to determine the limits is the highest gain of the individual chains and the EIRP is the sum of the products of gain and power on each chain. If the signals are coherent then the effective antenna gain is the sum (in linear terms) of the gains for each chain and the EIRP is the product of the effective gain and total power. R10161 Rev 1 UNII- Ant (MIMO) Page 108

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 Antenna Gain Information Antenna Gain (dbi) / Chain Freq 1 2 EMC Test Data Job Number: JD9961 T-Log Number: T10155 5150-5250 6.0 6.0 No Yes Yes No 6.00 9.01 5725-5850 6.0 6.0 No Yes Yes No 6.00 9.01 570-5725 6.0 6.0 No Yes Yes No 6.00 9.01 5725-5825 6.0 6.0 No Yes Yes No 6.00 9.01 BF MultiChain Legacy CDD Sectorized / Xpol Dir G (PWR) Dir G (PSD) For devices that support CDD modes Min # of spatial streams: 1 Max # of spatial streams: 2 Run #1: Bandwidth, Output Power and Power Spectral Density - MIMO Systems Date of Test: 05/11/16 Config. Used: Antenna Port Test Engineer: Mehran Birgani Config Change: - Test Location: Lab EUT Voltage: 120V/ 60Hz Notes: Notes: Notes: Notes: BF = beamforming mode supported, Multichain Legacy = 802.11 legacy data rates supported for multichain transmissions, CDD = Cyclic Delay Diversity (or Cyclic Shift Diversity) modes supported, Sectorized / Xpol = antennas are sectorized or cross polarized. Dir G (PWR) = total gain (Gant + Array Gain) for power calculations; GA (PSD) = total gain for PSD calculations based on FCC KDB 662911. Depending on the modes supported, the Array Gain value for power could be different from the PSD value. Array gain for power/psd calculated per KDB 662911 D01. For systems with Beamforming and CDD, choose one the following options: Option 1: Delays are optimized for beamforming, rather than being selected from cyclic delay table of 802.11; Array gains calculated based on beamforming criteria. Option 2: Antennas are paired for beamforming, and the pairs are configured to use the cyclic delay diversity of 802.11; the array gain associated with beamforming with 2 antennas (db), and the array gain associated with CDD with two antennas (db for PSD and 0 db for power) R10161 Rev 1 UNII- Ant (MIMO) Page 109

Client: Aruba Networks Standard: FCC 15.07 / RSS-210 EMC Test Data Job Number: JD9961 T-Log Number: T10155 MIMO Device - 5725-5850 MHz Band - FCC/IC Mode: 11a Max EIRP (mw): 0 Frequency Software 99% BW Duty Cycle Power Total Power 1 Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) Result 1 1.6 575 q65 16.8 99 62.7 18.0 0.0 Pass 2 15. 1 16.1 5785 q70 16.9 99 85. 19. 0.0 0.085 Pass 2 16.5 1 15.7 5825 q69 16.9 99 77.0 18.9 0.0 Pass 2 16.0 5725-5850 PSD - FCC/IC Mode: 11a Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/500khz Result 1.8 575 q65 99 5. 7. 27.0 27.0 Pass 2.7 1 5. 5785 q70 99 7.7 8.9 27.0 27.0 Pass 2 6. 1 5.0 5825 q69 99 6.8 8. 27.0 27.0 Pass 2 5.6 R10161 Rev 1 UNII- Ant (MIMO) Page 110

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII- Ant (MIMO) Page 111

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 MIMO Device - 5725-5850 MHz Band - FCC/IC Mode: n20 Max EIRP (mw): 51.9 Frequency Software 99% BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 1. 575 q65 18.0 98 59.2 17.7 0.0 2 15.0 1 16. 5785 q72 18.0 98 2 16.6 1 16.0 88. 19.5 0.0 5825 q72 18.0 98 8.5 19.2 0.0 2 16. 0.088 Result Pass Pass Pass 5725-5850 PSD - FCC/IC Mode: n20 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1.1 575 q65 98.6 6.6 27.0 27.0 Pass 2.0 1 5.1 5785 q72 98 6.9 8. 27.0 27.0 Pass 2 5.6 1.7 5825 q72 98 6. 8.0 27.0 27.0 Pass 2 5. R10161 Rev 1 UNII- Ant (MIMO) Page 112

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII- Ant (MIMO) Page 11

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 MIMO Device - 5725-5850 MHz Band - FCC/IC Mode: n0 Max EIRP (mw): 9.9 Frequency Software 99% BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 1. 5755 q65 6.5 96 58.1 17.6 0.0 2 1.6 0.088 1 16.1 5795 q72 6.5 96 87.9 19. 0.0 2 16. Result Pass Pass MIMO Device 5725-5850 PSD - FCC/IC Mode: n0 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC Limit Chain (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz Result 1-0.1 5755 q65 96 2.1.2 27.0 27.0 Pass 2 0.2 1 1.7 5795 q72 96.2 5.1 27.0 27.0 Pass 2 2.1 R10161 Rev 1 UNII- Ant (MIMO) Page 11

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 R10161 Rev 1 UNII- Ant (MIMO) Page 115

EMC Test Data Client: Aruba Networks Job Number: JD9961 T-Log Number: T10155 Standard: FCC 15.07 / RSS-210 MIMO Device - 5725-5850 MHz Band - FCC/IC Mode: ac80 Max EIRP (mw): 166.8 Frequency Software 99% BW Duty Cycle Power Total Power 1 FCC Limit Max Power Chain (MHz) Setting (MHz) % dbm mw dbm dbm (W) 1 12.8 5775 q58 75.9 9 1.9 16.2 0.0 0.02 2 1.0 Result Pass MIMO Device 5725-5850 PSD - FCC/IC Mode: ac80 Frequency Software 99% BW Duty Cycle PSD Total PSD 1 FCC Limit IC Limit Chain Result (MHz) Setting (MHz) % dbm/mhz mw/mhz dbm/mhz dbm/mhz 1 -.6 5775 q58 9 0.8-1.0 27.0 27.0 Pass 2 -. R10161 Rev 1 UNII- Ant (MIMO) Page 116