MUTIAYER ERAMI ANTENNA (INEAR POARIZATION MODE) OR 433MHz Preliminary Product pecification QUIK REERENE DATA Working requency Bandwidth requency Range Gain VWR Polarization 433 MHz 20 MHz (Min) 421 ~ 445 MHz 0.5 dbi (Max) 2.0 max inear Azimuth Omnidirectional Impedance Operating Temperature Termination Resistance to soldering heat 50Ω 55~125 o Ni/n (Environmentallyriendly eadless) 260 o, 10 sec. pecial Environmental oncerns Green Products Design: The foil making process is using environmentally friendly aqueous solvent technology. Termination is lead free and packing materials can be recycled 1. APPIATION liff Wang, Ph.D. Page 1/7 sheet 1901 A4
60 mm cleanness BAK IDE circuits space back side all ground plane (But under antenna should avoid ground plane) TOP IDE RModule 40 mm 50 ohm transmission line 2. ODER AND PATTERN OR ANTENNA igure Dimensions Remark 8.0 0.50 mm 3.50 0.50 mm 0.90 0.10 mm eed pad 3.50 0.50 mm Mount pad liff Wang, Ph.D. Page 2/7 sheet 1902 A4
3. MEHANIA DATA igure Dimension Port W 7.2±0.5mm W 38.0±0.5mm T 0.90±0.1mm 3.0±0.8mm eed termination T D D D 0.5±0.3mm 17.5±0.3mm older termination 2.0±0.8mm 4. TET BOARD DIMENION OR 11 (RETURN O) AND RADIATION PATTERN MEAURNMENT 40 mm 60 mm 50 ohm transmission line R4 PB thickness = 0.8 mm The length of transmission line = 1.35 mm ( depends on PB thickness) liff Wang, Ph.D. Page 3/7 sheet 1903 A4
5. 11 RETURN O 6. RADIATION PATTERN 0 0 45 45 45 45 90 90 90 90 135 225 135 225 E Plane 180 Antenna Gain = 2.2 dbi H Plane 180 REIABIITY DATA (Reference to IE pecification) liff Wang, Ph.D. Page 4/7 sheet 1904 A4
IE 38410/ E 32 100 AUE IE 60068682 TET METHOD TET PROEDURE REQUIREMENT 4.4 Mounting The antenna can be mounted on printedcircuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive 4.5 Visual inspection and dimension check Any applicable method using 10 magnification 4.6.1 Antenna requency = 433MHz at 20 4.8 Adhesion A force of 5 N applied for 10 s to the line joining the terminations and in a plane parallel to the substrate 4.9 Bond strength of plating on end face Mounted in accordance with E 32 100, paragraph 4.4 In accordance with specification (no chip off 3 mm) tandard test board on page 4 4.10 Tb Resistance to soldering heat onditions: bending 0.5 mm at a rate of 1mm/s, radius jig. 340 mm, 1 mm warp on R4 board of 90 mm length 260 5 for 10 0.5 s in a static solder bath The terminations shall be well tinned after recovery and entral req. hange liff Wang, Ph.D. Page 5/7 sheet 1905 A4
IE 38410/ E 32 100 AUE IE 60068682 TET METHOD Resistance to leaching TET PROEDURE REQUIREMENT 260 5 for 30 1 s in a static solder bath 4.11 Ta olderability Zero hour test, and test after storage (20 to 24 months) in original atmosphere; unmounted chips completely immersed for 2 0.5 s in 235 5. 4.12 Na Rapid change of temperature 55 (30 minutes) to +125 (30 minutes); 100 cycles 4.14 a Damp heat 500 12 hours at 60 ; 90 to 95 % RH Using visual enlargement of 10, dissolution of the termination shall not exceed 10% The termination must be well tinned, at least 75% is well tinned at termination entral req. hange 2 hours recovery entral req. hange 4.15 Endurance 500 12 hours at 125 2 hours recovery entral req. hange liff Wang, Ph.D. Page 6/7 sheet 1906 A4
ORDERING INORMATION: 12N Ordering ode The antennas may be ordered by using the 12 N ordering code. These code numbers can be determined by the following rules: 4313 1 21 20 043 M T A. amily ode. Packing Type ode 43 = Antenna 13 = Bulk, 1000 pcs M. Materials ode 1 = High requency Material. ize ode 21 = 7.2 * 38.0 * 0.9 mm T. Tolerance 20 = 20 MHz Bandwidth A. Working requency 043 = 433MHz Example: 12N 4313 121 20043 Product description: Antenna (43) by bulk 1000 pcs (13) of High requency Material (1), ize 7.2*38*0.9 mm (21); Tolerance (20) of 20 MHz (VWR<2) Working requency (043) = 433MHz ORDERING INORMATION: Method II by lear Text ode (Temporary) The antennas may be ordered by using the 16digit clear text ordering code. These code numbers can be determined by the following rules: AN0433200707381B (lear Text ode Example) AN 0433 20 07 0738 1 B Product entral req. Bandwidth Material ize Quantities Packing AN= 0433=433MHz 20= >20MHz 07=K7 0738=7.2*38* 1 = 1K B = Bulk Antenna 0.9 mm liff Wang, Ph.D. Page 7/7 sheet 1907 A4