Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 000000000 000W Power Supply with Single Output RSP-000 series File Name:RSP-000PEC 08--0
000W Power Supply with Single Output RSP-000 series SPECIFICATION MODEL OUTPUT INPUT PROTECTION FUNCTION ENVIRONMENT SAFETY & EMC (Note 5) OTHERS NOTE RSP-000- RSP-000-5 RSP-000-4 RSP-000-7 RSP-000-48 DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER V A 0 ~ A 70W 5V 50A 0 ~ 50A 750W 4V 40A 0 ~ 40A 9W 7V 37A 0 ~ 37A 999W 48V A 0 ~ A 008W RIPPLE & NOISE (max.) Note. 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p VOLTAGE ADJ. RANGE 0 ~ 3.5V 3.5 ~ 6.5V 0 ~ 6.4V 4 ~ 30V 43 ~ 55V VOLTAGE TOLERANCE Note.3 ±.0% ±.0% ±.0% ±.0% ±.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME 300ms, 50ms at full load HOLD UP TIME (Typ.) 6ms/30VAC 6ms/5VAC at full load VOLTAGE RANGE Note.4 90 ~ 64VAC 7 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) 0.95/30VAC 0.98/5VAC at full load EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER OVER VOLTAGE OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down OUTPUT VOLTAGE PROGRAMMABLE(PV) Adjustment of output voltage is allowable to 40 ~ 0% of nominal output voltage. Please refer to the Function Manual. CURRENT SHARING Up to 4000W or (3+) units. Please refer to the Function Manual. AUXILIARY POWER 5V @ 0.5A (+5%, -8%) REMOTE ON-OFF CONTROL Power ON : short Power OFF : open. Please refer to the Function Manual. REMOTE SENSE Compensate voltage drop on the load wiring up to 0.5V. Please refer to the Function Manual. DC OK SIGNAL WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION MTBF DIMENSION PACKING 83% 85% 88% 88% 90% A/5VAC 5A/5VAC 6A/30VAC 40A/30VAC <.0mA / 40VAC 05 ~ 5% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 3.8 ~ 6.8V 7 ~ 0.5V 7.6 ~ 3.4V 3 ~ 36.5V 56.6 ~ 66.V Protection type : Shut down o/p voltage, re-power on to recover The TTL signal out, PSU turn on = 0 ~ V ; PSU turn off = 3.3 ~ 5.6V. Please refer to the Function Manual. -0 ~ + (Refer to "Derating Curve") 0 ~ 90% RH non-condensing -40 ~ +85, 0 ~ 95% RH non-condensing ± 0.0%/ (0 ~ 50 ) 0 ~ 500Hz, G 0min./cycle, min. each along X, Y, Z axes SAFETY STANDARDS UL950-, TUV EN950-, EAC TP TC 004, CCC GB4943., BSMI CNS4336- approved WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY I/P-O/P:3KVAC I/P-FG:KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500VDC / 5 / 70% RH Parameter Standard Conducted Radiated Harmonic Current Voltage Flicker EN5503 (CISPR3) / EN550 (CISPR) Class B EN5503 (CISPR3) / EN550 (CISPR) Class A EN00-3- ----- EN00-3-3 ----- 33.K hrs min. Telcordia SR-33 (Bellcore) ; 6.75K hrs min. MIL-HDBK-7F (5 ) 95*7*4mm (L*W*H).95Kg; 6pcs/.7Kg/.5CUFT Test Level / Note En5504, EN4-3, EN00-6-, CCC GB765., GB/T954, BSMI CNS3438 Parameter ESD Radiated EFT / Burst Surge Conducted Magnetic Field Voltage Dips and Interruptions Standard EN00-4- EN00-4-3 EN00-4-4 EN00-4-5 EN00-4-6 EN00-4-8 EN00-4- Test Level / Note Level 3, 8KV air ; Level, 4KV contact Level 3 Level 3 Level 4, 4KV/Line-Earth ; Level 3, KV/Line-Line Level 3 Level 4 >95% dip 0.5 periods, 30% dip 5 peniods, >95% interruptions 50 periods File Name:RSP-000PEC 08--0
000W Power Supply with Single Output RSP-000 series Block Diagram PFC fosc : 0KHz PWM fosc : 90KHz I/P EMI FILTER ACTIVE INRUSH CURRENT LIMITING PFC CONTROL RECTIFIERS & PFC PWM CONTROL POWER SWITCHING O.L.P. RECTIFIERS & FILTER CURRENT SHARE DETECTION CIRCUIT CURRENT SHARE DC OK V_TRIM O.V.P. AUX POWER FAN RECTIFIERS CONTROL ON/OFF RECTIFIERS & FILTER REMOTE ON-OFF AUX POWER(5V/0.5A) AUX Static Characteristics 00 90 70 MODEL INPUT 00~64VAC V 70W A 5V 4V 7V 48V 750W 9W 999W 008W 50A 40A 37A A (%) 50 40 90VAC 648W 54A 675W 45A 864W 36A 899.W 33.3A 907.W 8.9A 90 95 00 5 64 INPUT VOLTAGE (VAC) Hz Derating Curve Efficiency vs Load (48V Model) 95 (%) 00 40 0-0 0 0 0 30 40 50 70 (HORIZONTAL) AMBIENT TEMPERATURE ( ) EFFICIENCY (%) 90 85 75 70 65 0% 0% 30% 40% 50% % 70% % 90% 00% The curve above is measured at 30VAC. File Name:RSP-000PEC 08--0
000W Power Supply with Single Output RSP-000 series Function Manual.Remote Sense The Remote Sense compensates voltage drop on the load wiring up to 0.5V Sense lines should be twisted in pairs to minimize noise pick-up. PIN TB PIN PIN0 Vca PIN8 Vco The signal should be connected to the positive terminal of the load whereas signal to the negative terminal. This configuration is based on the assumption the Output Voltage Programming is not activated and power supply is ON. Fig..Remote ON-OFF Control The power supply can be turned ON-OFF indivicluaaly or along with other units by using the Remote ON-OFF function. Between Remote ON-OFF (pin6) and (pin) Switch Short Switch Open Power Supply Status ON OFF + - Fig. TB PIN PIN0 Vca PIN8 Vco Switch The power supply is shipped, by factory default, with Remote ON-OFF(pin6) and (pin) shorted by connector. When multiple power supplies need to turn ON/OFF simultaneously by Remote ON-OFF control, &, as well as &, on each power supply should be connected. 3.DC_OK signal "DC_OK" is an open collector signal. It indicates the output status of the power supply. It can operate in two ways : One is sinking current from external TTL signal ; the other is sending out a TTL voltage signal. Sinking current from external TTL signal: The maximum sink current is 0mA and the maximum external voltage is 5.6V. Sending out TTL voltage signal : Between DC- OK(pin5) and (pin&) Output Status 0 ~ V 3.3 ~ 5.6V ON OFF PIN5 DC_OK PIN TB PIN PIN0 Vca PIN8 Vco Fig 3. File Name:RSP-000PEC 08--0
000W Power Supply with Single Output RSP-000 series 4. Output Voltage Programming (or, PV / remote voltage programming / remote adjust / margin programming / dynamic voltage trim) In addition to the adjustment via the built-in potentiometer, the output voltage can be trimmed to 40~0% of the nominal voltage by applying either an EXTERNAL VOLTAGE or an EXTERNAL RESISTANCE. ()Applying EXTERNAL VOLTAGE between " Vci "(pin9) and ""(pin) as shown in Fig4. AUXG DC_OK CS Vci AUX ON/OFF Vco Vca PIN External Voltage TB PIN PIN9 Vci EXTERNAL VOLTAGE (DC) & and & also need to be connected on ()Applying EXTERANL RESISTANCE as shown in Fig4. & Fig 4.3 (A) Output voltage goes down Fig 4. AUXG DC_OK CS Vci PIN3 AUXG PIN PIN9 Vci AUX REMOTE ON-OFF Vco Vca (B)Output voltage goes up TB PIN PIN4 AUX & and & also need to be connected on. PIN0 Vca R Fig 4. R AUXG DC_OK CS Vci PIN3 AUXG PIN PIN9 Vci AUX REMOTE ON-OFF Vco Vca R TB PIN PIN4 AUX PIN0 Vca R & and & also need to be connected on. Fig 4.3 Vout OVP 0%(Typ.) Vout Vout OVP 0%(Typ.) OUTPUT VOLTAGE (%) 0 00 40 0 Non-Linear Vci(Referenced to ) 3 4 5 6 EXTERNAL VOLTAGE (VDC) OUTPUT VOLTAGE (%) 00 90 70 50 40 Non-Linear R, /8W(Typ.) 390 5 K K 4K7 open EXTERNAL RESISTANCE ( Ω) open 8K 7K5 EXTERNAL RESISTANCE ( Ω) Fig 4.. Fig 4.. Fig 4.3. OUTPUT VOLTAGE (%) 0 05 00 Non-Linear R, /8W(Typ.) Caution: By factory default, the Output Voltage Programming is not activated, and Vco (pin8) and Vca(pin0) are shorted by connector. Whenever this function is not needed to activate, as assumed in other sections diagrams, please keep Vco(pin8) and Vca(pin0) shorted ; other wise, the power supply will have no output. File Name:RSP-000PEC 08--0
000W Power Supply with Single Output RSP-000 series 5.Current Sharing with Remote Sense RSP-000 has the built-in active current sharing function and can be connected in parallel, up to 4 units, to provide higher output power as exhibited below : The power supplies should be paralleled using short and large diameter wiring and then connected to the load. Difference of output voltages among parallel units should be less than 0.V. The total output current must not exceed the value determined by the following equation: Maximum output current at parallel operation=(rated current per unit) (Number of unit) 0.9 When the total output current is less than 5% of the total rated current, or say (5% of Rated current per unit) (Number of unit) the current shared among units may not be fully balanced. PSU PSU PSU PSU TB TB TB TB (pin) (pin) CS(pin7) Sense lines should be twisted in pairs Fig 5. AUXG DC_OK CS Vci AUX ON/OFF Vco Vca AUXG DC_OK CS Vci AUX ON/OFF Vco Vca AUXG DC_OK CS Vci AUX ON/OFF Vco Vca AUXG DC_OK CS Vci AUX ON/OFF Vco Vca, and CS are connected mutually in parallel. File Name:RSP-000PEC 08--0
000W Power Supply with Single Output RSP-000 series Mechanical Specification Case No. 95B Unit:mm 0.5 6 3-M4 L=6 95 4 34.5 77.7 5.4 7.8 -M5 8.5 59 7 SVR5 7 0 TB 3 90 3-M4 L=4 Air flow direction 0.5 3-M4 L=6 5.4 6 77.7 7.8 Mounting Instruction Hole No. Recommended Screw Size MAX. Penetration Depth L Recommended mounting torque M4 M4 6mm 4mm Control Pin No. Assignment () : HRS DF-DP-DS or equivalent Mating Housing HRS DF-DS or equivalent Terminal HRS DF-**SC or equivalent 7~Kgf-cm 7~Kgf-cm Mounting Surface Mounting Screw L Chassis of RSP-000 Pin No. Function Description Positive sensing for remote sense. Negative sensing for remote sense. 3 G-AUX Auxiliary voltage output ground. The signal return is isolated from the output terminals ( & ). 4 5 5V-AUX DC_OK Auxiliary voltage output, 4.6~5.5V, referenced to pin 3(G-AUX). The maximum load current is 0.5A. This output has the built-in oring diodes and is not controlled by the "remote ON/OFF control". Open collector signal, referenced to pin,(). Low when PSU turns on. The maximum sink current is 0mA and the maximum external voltage is 5.6V. 6 Remote ON-OFF Turns the output on and off by electrical or dry contact between pin 6 (Remote ON-OFF) and pin (). Short: Power ON, Open: Power OFF. 7 8 9 0, CS Vco Vci Vca Current sharing signal. When units are connected in parallel, the CS pins of the units should be connected to allow current balance between units. Short connecting between Vco (pin8) and Vca (pin0) if output voltage programming function is not activated. Connect to external DC voltage source for output voltage programming, referenced to pin (). Connect to external resistor (/8W) for output voltage programming. These pins connect to the negative terminal (). Return for DC_OK Signal output. File Name:RSP-000PEC 08--0
000W Power Supply with Single Output RSP-000 series AC Input Terminal Pin No. Assignment Pin No. 3 Assignment Diagram Mx a imum mounting torque AC/N AC/L 8Kgf-cm FG DC Output Terminal Pin No. Assignment Assignment Diagram Mx a imum mounting torque, 0Kgf-cm Installation Manual Please refer to : http://www.meanwell.com/manual.html File Name:RSP-000PEC 08--0