Anchor selector Anchor type Base Approvals Application Mechanical anchor systems Heavy duty anchors HDA-T/ -TR/TF/-P/-PR/-PF undercut anchor Anchor fastening for high loads e.g. in steel construction and plant construction HSL-3 heavy duty anchor Fastening heavy loads e.g. from columns, high racks, machines HSL-GR heavy duty anchor Fastening heavy loads Medium and light duty anchors HSC-A(R) /-I(R) safety anchor Safety relevant fastening at facades and ceilings where short embedment depth is required HST/-R/-HCR stud anchor Fastening through in place parts e.g. angles, tracks, channels, wooden beams, etc. HSA/-R/-R2/-F stud anchor Fastening through in place parts like wooden beams, metal sections, columns, brackets, etc. HSV stud anchor Fastening through in place parts HLC sleeve anchor Temporary fastenings in concrete (e.g. formwork), fastening in base of low density = very suitable = may be suitable per application = technical report redundant fastening 8
Advantages Drill bit diameter resp. anchor size Steel, galvanised Steel, sheradised, hot dipped galv. Specification Setting Page Stainless steel A2 (1.4303) Stainless steel A4 (1.440 HCR steel (1.4529) External thread Internal thread Pre-setting Through-fastening Automatic undercutting High load capacity Approved for all dynamic loads 20 37 mm M10 M20 72 Integrated plastic section to telescope and pull down tightly The bolt can be retorqued Integrated plastic section to telescope and pull down tightly The bolt can be retorqued 12 32 mm M8 M24 12 28 mm M8 M20 88 100 Automatic undercutting Small edge distances and spacings Small setting depth Quick and simple setting operation Setting mark Safety wedge for certain follow up expansion Three setting depths Setting mark Extremely ductile steel for high bending capacity Quick and simple setting operation Short setting and removing operation Good loads in green concrete Bridging of gaps 14 20 mm M6 M12 8 24 mm M8 M24 6 20 mm M8 M24 8 16 mm M8 M16 6,5 20 mm M5 M16 110 130 140 158 168 9
Anchor type Base Approval Application Medium and light duty anchors HAM hard sleeve anchor Secure fastenings in various base s HUS-HR screw anchor, stainless steel Fastening channels, brackets, racks, seating HUS screw anchor, carbon steel Fastening channels, brackets, racks, seating HUS- 6 screw anchor, redundant fastening Fastening channels, brackets, racks, seating HUS 6 / HUS-S 6 screw anchor Fastening light channels, brackets, interior panelling or cladding HKD push-in anchor Fastening with threaded rods for pipe suspensions, air ducts, suspended ceilings HKV push-in anchor Fastening with threaded rods for pipe suspensions, air ducts, suspended ceilings HUD-1 universal anchor Various applications HUD-L universal anchor Various applications = very suitable = may be suitable per application = technical report redundant fastening 10
Advantages Drill bit diameter resp. anchor size Steel, galvanised Steel, sheradised, hot dipped galv. Specification Setting Page Stainless steel A2 (1.4303) Stainless steel A4 (1.440 HCR steel (1.4529) External thread Internal thread Pre-setting Through-fastening Wings to prevent spinning in the bore hole Plastic cap in cone to prevent dust entrance 12 20 mm Thread: M6 M12 174 Screw driven straight into base Forged on washer Matched system of screw anchor and screw driver Screw driven straight into base Forged on washer Matched system of screw anchor and screw driver Screw driven straight into base Forged on washer Matched system of screw anchor and screw driver 6 14 mm 8 14 mm 6 mm 176 192 216 Screw driven straight into base Small drill bit diameter Matched system of screw anchor and screw driver Visual verification of full expansion Small setting depth Visual verification of full expansion Small setting depth Fast setting Flexibility of screw length An anchor for every base Fast setting Flexibility of screw length An anchor for every base 6 mm 8 25 mm M6 M20 8 20 mm M6 M16 5 14 mm 6 10 mm 222 228 250 254 260 11
Anchor type Base Approvals Application Medium and light duty anchors HLD light duty anchor Fastenings to weak with cavities HRD-U/-S frame anchor Securing support frames, timber frames, fascade panels, curtain walling HRD frame anchor On most hollow and solid base HPS-1 impact anchor Fastening wood battens, components for electrical and plumbing installations HHD-S cavity anchor Fastening battens, channels panels HCA coil anchor Temporary external fastenings HSP/HFPdrywall plug Fastenings in dry walls HA8 ring/ hook anchor For suspended ceilings and other items from concrete ceilings DBZ wedge anchor Suspension from concrete ceilings e.g. using steel straps, punched band, Nonius system hanger HT metal frame anchor Fastening door and window frames = very suitable = may be suitable per application = technical report redundant fastening 12
Advantages Drill bit diameter resp. anchor size Steel, galvanised Steel, sheradised, hot dipped galv. Specification Setting Page Stainless steel A2 (1.4303) Stainless steel A4 (1.440 HCR steel (1.4529) External thread Internal thread Pre-setting Through-fastening Flexibility of screw length Resilient toggling action to suit every base 10 mm 264 Preassembled with screw Screw of steel strength 5.8 or stainless steel A4 (1.440 10 and 14 mm 268 impact and temperature resistant high quality plastic 8 10 mm 274 impact and temperature resistant high quality plastic 4 8 mm 292 Controlled setting Deliverable with or without prefitted screw 8 12 mm 296 Re-usable Removable 16 mm 298 Self-drilling tip One bit for anchor and screw Removable - 300 Quick and easy setting Automatic follow up expansion 8 mm 302 Small drill bit diameter Quick setting by impact extension Automatic follow up expansion No risk of distortion or forces of constraint Expansion cone can not be lost 6 mm 8 10 mm 306 310 13
Anchor type Base Approvals Application Medium and light duty anchors HK ceiling anchor Fastening of suspended ceilings, cable trays, pipes HPD aerated concrete anchor Various fastenings HKH hollow deck anchor Suspension from prestressed concrete hollow decks HTB Ingenious and strong for hollow base s Insulation fasteners IDP insulation fastener Fastening of hard, self supporting insulating s IZ expandable insulation fastener Fastening of soft and hard, self supporting insulating s IDMS / IDMR insulation fastener Fastening of soft and hard, self supporting insulating s and non self supporting insulation s = very suitable = may be suitable per application = technical report redundant fastening 14
Advantages Drill bit diameter resp. anchor size Steel, galvanised Steel, sheradised, hot dipped galv. Specification Setting Page Stainless steel A2 (1.4303) Stainless steel A4 (1.440 HCR steel (1.4529) External thread Internal thread Pre-setting Through-fastening Small bore hole Quick and easy setting Approved (DIBt) Fire resistance Immediately loadable Approval for single point fastenings Approved for sprinkler systems Load carried by strong metal channel and screw Convincing simplicity when setting 6 mm M6 Without predrilling Thread: M6 M10 10 14 mm Thread: M6 M10 13 14 mm 314 320 326 330 One piece element Corrosion resistant No heat bridge Corrosion resistant No heat bridge Reliable bonding of plaster 8 mm insulating thickness 10 150mm 8 mm insulating thickness up to 180mm 334 338 One piece element Corrosion resistant Fire resistant 8 mm insulating thickness up to 150mm 342 15
Anchor type Base Approvals Application Adhesive anchor systems Foil capsule systems HVZ adhesive anchor HVU adhesive anchor Heavy-duty fastenings with small spacing and edge distances Heavy duty fastenings with small spacing and edge distances Injection mortar systems HIT-RE 500 SD Adhesive anchor in cracked concrete HIT-RE 500 Adhesive anchor HIT-HY 200 Adhesive anchor in cracked concrete = very suitable = may be suitable per application = technical report redundant fastening 16
Advantages Drill bit diameter resp. anchor size Steel, galvanised Steel, sheradised, hot dipped galv. Specification Setting Page Stainless steel A2 (1.4303) Stainless steel A4 (1.440 HCR steel (1.4529) External thread Internal thread Pre-setting Through-fastening No expansion pressure Small edge distances and spacing A strong and flexible foil capsule No expansion pressure Small edge distances and spacing A strong and flexible foil capsule M10 M20 348 HAS M8 M39 HIS-M8 - M20 Rebar dia. 8 40 mm 360 No expansion pressure Long working time HIT-V M8 M30 HIS-M8 - M20 Rebar dia. 8 32 mm 380 No expansion pressure Long working time HIT-V M8 M39 HIS-M8 - M20 Rebar dia. 8 40 mm 422 No expansion pressure Flexibility in terms of working time No styrene content No plasticizer content Environmental protection due to the minimized packaging HIT-V M8 M30 HIS-M8 - M20 Rebar dia. 8 32 mm 488 17
Anchor type Base Approvals Application Injection mortar systems HIT-HY 150 MAX Adhesive anchor in cracked concrete HIT-CT 1 Hilti Clean technology adhesive anchor HIT-HY 150 Adhesive anchor HIT ICE Adhesive anchor for low installation temperatures HIT-HY 70 Universal mortar for solid and hollow brick = very suitable = may be suitable per application = technical report redundant fastening 18