ETSI TS 125 104 V3.1.0 (2000-01) Technical Specification Universal Mobile Telecommunications System (UMTS); UTRA (BS) FDD; Radio transmission and Reception (3G TS 25.104 version 3.1.0 Release 1999)
(3G TS 25.104 version 3.1.0 Release 1999) 1 ETSI TS 125 104 V3.1.0 (2000-01) Reference DTS/TSGR-0425104U Keywords UMTS ETSI Postal address F-06921 Sophia Antipolis Cedex - FRANCE Office address 650 Route des Lucioles - Sophia Antipolis Valbonne - FRANCE Tel.:+33492944200 Fax:+33493654716 Siret N 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N 7803/88 Internet secretariat@etsi.fr Individual copies of this ETSI deliverable can be downloaded from http://www.etsi.org If you find errors in the present document, send your comment to: editor@etsi.fr Important notice This ETSI deliverable may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2000. All rights reserved. ETSI
(3G TS 25.104 version 3.1.0 Release 1999) 2 ETSI TS 125 104 V3.1.0 (2000-01) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://www.etsi.org/ipr). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by the ETSI 3 rd Generation Partnership Project (). The present document may refer to technical specifications or reports using their identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The mapping of document identities is as follows: For documents: 3G TS TR nn.nnn "<title>" (with or without the prefix 3G) is equivalent to ETSI TS TR 1nn nnn "[Digital cellular telecommunications system (Phase 2+) (GSM);] Universal Mobile Telecommunications System; <title> For GSM document identities of type "GSM xx.yy", e.g. GSM 01.04, the corresponding ETSI document identity may be found in the Cross Reference List on www.etsi.org/key ETSI
3 TS 25.104 v3.1.0 (1999-12) Contents Foreword... 6 1 Scope... 6 2 References... 6 3 Definitions, symbols and abbreviations... 6 3.1 Definitions... 6 3.2 Symbols... 7 3.3 Abbreviations... 8 4 General... 9 4.1 Measurement uncertainty... 9 4.2 Base station classes... 9 5 Frequency bands and channel arrangement... 10 5.1 General... 10 5.2 Frequency bands... 10 5.3 Tx Rx frequency separation... 10 5.4 Channel arrangement... 10 5.4.1 Channel spacing... 10 5.4.2 Channel raster... 10 5.4.3 Channel number... 10 6 Transmitter characteristics... 12 6.1 General... 12 6.2 Base station output power... 12 6.2.1 Base station maximum output power... 12 6.2.1.1 Minimum requirement... 12 6.3 Frequency stability... 12 6.3.1 Minimum requirement... 12 6.4 Output power dynamics... 12 6.4.1 Inner loop power control in the downlink... 12 6.4.1.1 Power control steps... 12 6.4.1.1.1 Minimum requirement... 12 6.4.2 Power control dynamic range... 13 6.4.2.1 Minimum requirements... 13 6.4.3 Total power dynamic range... 13 6.4.3.1 Minimum requirement... 13 6.4.4 Primary CPICH power... 14 6.4.4.1 Requirement... 14 6.6 Output RF spectrum emissions... 14 6.6.1 Occupied bandwidth... 14 6.6.2 Out of band emission... 14 6.6.2.1 Spectrum emission mask... 14 6.6.2.2 Adjacent Channel Leakage power Ratio (ACLR)... 16 6.6.2.2.1 Minimum requirement... 16 6.6.2.3 Protection outside a licensee s frequency block... 16 6.6.2.3.1 Minimum requirement... 16 6.6.3 Spurious emissions... 16 6.6.3.1 Mandatory Requirements... 17 6.6.3.1.1 Spurious emissions (Category A)... 17 6.6.3.1.1.1 Minimum Requirement... 17 6.6.3.1.2 Spurious emissions (Category B)... 17 6.6.3.1.2.1 Minimum Requirement... 17 6.6.3.2. Protection of the BS receiver... 18 6.6.3.2.1 Minimum Requirement... 18
4 TS 25.104 v3.1.0 (1999-12) 6.6.3.3 Co-existence with GSM 900... 19 6.6.3.3.1 Operation in the same geographic area... 19 6.6.3.3.1.1 Minimum Requirement... 19 6.6.3.3.2 Co-located base stations... 19 6.6.3.3.2.1 Minimum Requirement... 19 6.6.3.4 Co-existence with DCS 1800... 19 6.6.3.4.1 Operation in the same geographic area... 19 6.6.3.4.1.1 Minimum Requirement... 20 6.6.3.4.2 Co-located base stations... 20 6.6.3.4.2.1 Minimum Requirement... 20 6.6.3.5 Co-existence with PHS... 20 6.6.3.5.1 Minimum Requirement... 20 6.6.3.6 Co-existence with services in adjacent frequency bands... 20 6.6.3.6.1 Minimum requirement... 20 6.6.3.7 Co-existence with UTRA-TDD... 21 6.6.3.7.1 Operation in the same geographic area... 21 6.6.3.7.1.1 Minimum Requirement... 21 6.6.3.7.2 Co-located base stations... 21 6.6.3.7.2.1 Minimum Requirement... 22 6.7 Transmit intermodulation... 22 6.7.1 Minimum requirement... 22 6.8 Transmit modulation... 22 6.8.1 Transmit pulse shape filter... 22 6.8.2 Modulation Accuracy... 22 6.8.2.1 Minimum requirement... 22 6.8.3 Peak code Domain error... 23 6.8.3.1 Minimum requirement... 23 7 Receiver characteristics... 24 7.1 General... 24 7.2 Reference sensitivity level... 24 7.2.1 Minimum requirement... 24 7.2.2 Maximum Frequency Deviation for Receiver Performance...24 7.3 Dynamic range... 24 7.4 Adjacent Channel Selectivity (ACS)... 24 7.4.1 Minimum requirement... 24 7.5 Blocking characteristics... 25 7.5.1 Minimum requirement... 25 7.6 Intermodulation characteristics... 26 7.6.1 Minimum requriement... 26 7.7 Spurious emissions... 26 7.7.1 Minimum requirement... 26 8 Performance requirement... 27 8.1 General... 27 8.2 Demodulation in static propagation conditions... 27 8.2.1 Demodulation of DCH... 27 8.2.1.1 Minimum requirement... 27 8.3 Demodulation of DCH in multipath fading conditions... 28 8.3.1 Multipath fading Case 1... 28 8.3.1.1 Minimum requirement... 28 8.3.2 Multipath fading Case 2... 28 8.3.2.1 Minimum requirement... 28 8.3.3 Multipath fading Case 3... 28 8.3.3.1 Minimum requirement... 29 8.4 Demodulation of DCH in moving propagation conditions... 29 8.4.1 Minimum requirement... 29 8.5 Demodulation of DCH in birth/death propagation conditions... 29 8.5.1 Minimum requirement... 30 Annex A (normative): Measurement channels... 31 A.1 Summary of UL reference measurement channels... 31 A.2 UL reference measurement channel for 12.2 kbps... 32
5 TS 25.104 v3.1.0 (1999-12) A.3 UL reference measurement channel for 64 kbps... 33 A.4 UL reference measurement channel for 144 kbps... 34 A.5 UL reference measurement channel for 384 kbps... 35 A.6 UL reference measurement channel for 2048 kbps... 36 Annex B (normative): Propagation conditions... 37 B.1 Static propagation condition... 37 B.2 Multi-path fading propagation conditions... 37 B.3 Moving propagation conditions... 37 B.4 Birth-Death propagation conditions... 38 Annex C (informative): Change request history... 39 History... 40
6 TS 25.104 v3.1.0 (1999-12) Foreword This Technical Specification has been produced by the. The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of this TS, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version 3.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 Indicates TSG approved document under change control. y z the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. the third digit is incremented when editorial only changes have been incorporated in the specification. 1 Scope This document establishes the Base Station minimum RF characteristics of the FDD mode of UTRA. 2 References The following documents contain provisions, which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, subsequent revisions do apply. A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same number. [1] ITU-R Recommendation SM.329-7, Spurious emissions. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following definitions apply:
7 TS 25.104 v3.1.0 (1999-12) Power Setting Maximum Power Setting Maximum output Power Peak Power Maximum peak power Average transmit power Maximum average power The value of the control signal, which determines the desired transmitter, output Power. Typically, the power setting would be altered in response to power control commands The highest value of the Power control setting which can be used. This refers to the measure of power when averaged over the transmit timeslot at the maximum power setting. The instantaneous power of the RF envelope which is not expected to be exceeded for [99.9%] of the time The peak power observed when operating at a given maximum output power. The average transmitter output power obtained over any specified time interval, including periods with no transmission. The average transmitter output power obtained over any specified time interval, including periods with no transmission, when the transmit time slots are at the maximum power setting. 3.2 Symbols For the purposes of the present document, the following symbols apply: <symbol> <Explanation>
8 TS 25.104 v3.1.0 (1999-12) 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: ACIR ACLR ACS BS BER CW DL EIRP FDD FER MER PPM RSSI SIR TDD TPC UE UL UTRA Adjacent Channel Interference Ratio Adjacent Channel Leakage power Ratio Adjacent Channel Selectivity Base Station Bit Error Rate Continuous Wave (unmodulated signal) Down Link (forward link) Effective Isotropic Radiated Power Frequency Division Duplexing Frame Error Rate Message Error Rate Parts Per Million Received Signal Strength Indicator Signal to Interference ratio Time Division Duplexing Transmit Power Control User Equipment Up Link (reverse link) UMTS Terrestrial Radio Access
9 TS 25.104 v3.1.0 (1999-12) 4 General 4.1 Measurement uncertainty The requirements given in this specification are absolute. Compliance with the requirement is determined by comparing the measured value with the specified limit, without making allowance for measurement uncertainty. 4.2 Base station classes The requirements in this specification apply to base station intended for general-purpose applications. In the future further classes of base stations may be defined; the requirements for these may be different than for general-purpose applications.
10 TS 25.104 v3.1.0 (1999-12) 5 Frequency bands and channel arrangement 5.1 General The information presented in this section is based on a chip rate of 3.84 Mcps. Note 1. Other chip rates may be considered in future releases. 5.2 Frequency bands UTRA/FDD is designed to operate in either of the following paired bands; (a) 1920 1980MHz: Up-link (Mobile transmit, base receive) 2110 2170MHz: Down-link (Base transmit, mobile receive) (b)* 1850 1910MHz: Up-link (Mobile transmit, base receive) 1930 1990MHz: Down-link (Base transmit, mobile receive) * Used in Region 2 Additional allocations in ITU region 2 are FFS. Deployment in other frequency bands is not precluded. 5.3 Tx Rx frequency separation (a) The minimum transmit to receive frequency separation is 134.8 MHz and the maximum value is 245.2 MHz and all UE(s) shall support a TX RX frequency separation of 190 MHz when operating in the paired band defined in subclause 5.2(a). (b) UTRA/FDD can support both fixed and variable transmit to receive frequency separation. (c) When operating in the paired band defined in sub-clause 5.2(b), all UE(s) shall support a TX RX frequency separation of 80 MHz. (d) The use of other transmit to receive frequency separations in existing or other frequency bands shall not be precluded. 5.4 Channel arrangement 5.4.1 Channel spacing The nominal channel spacing is 5 MHz, but this can be adjusted to optimize performance in a particular deployment scenario. 5.4.2 Channel raster The channel raster is 200 khz, which means that the center frequency must be an integer multiple of 200 khz. 5.4.3 Channel number The carrier frequency is designated by the UTRA Absolute Radio Frequency Channel Number (UARFCN). The value of the UARFCN in the IMT2000 band is defined as follows;
11 TS 25.104 v3.1.0 (1999-12) Table 1: UTRA Absolute Radio Frequency Channel Number Uplink N u = 5 * (F uplink MHz) 0.0 MHz F uplink 3276.6 MHz where F uplink is the uplink frequency in MHz Downlink N d = 5 * (F downlink MHz) 0.0 MHz F uplink 3276.6 MHz where F downlink is the downlink frequency in MHz
12 TS 25.104 v3.1.0 (1999-12) 6 Transmitter characteristics 6.1 General Unless detailed the transmitter characteristic are specified at the antenna connector. 6.2 Base station output power Output power, Pout, of the base station is the mean power of one carrier delivered to a load with resistance equal to the nominal load impedance of the transmitter. 6.2.1 Base station maximum output power Maximum output power, Pmax, of the base station is the mean power level per carrier that the manufacturer has declared to be available at the antenna connector. 6.2.1.1 Minimum requirement In normal conditions, the Base station maximum output power shall remain within +2 db and 2dB of the manufacturer s rated power. In extreme conditions, the Base station maximum output power shall remain within +2.5 db and 2.5 db of the manufacturer s rated power. 6.3 Frequency stability Frequency stability is ability of the BS to transmit at the assigned carrier frequency. 6.3.1 Minimum requirement The modulated carrier frequency of the BS shall be accurate to within ± 0.05 ppm for RF frequency generation. 6.4 Output power dynamics Power control is used to limit the interference level. The transmitter uses a quality-based power control on both the uplink and downlink. 6.4.1 Inner loop power control in the downlink Inner loop power control in the downlink is the ability of the BS transmitter to adjust the transmitter output power of a code channel in accordance with the corresponding TPC symbols received in the uplink. 6.4.1.1 Power control steps The power control step is the required step change in the DL transmitter output power of a code channel in response to the corresponding power control command. The combined output power change is the required total change in the DL transmitter output power of a code channel in response to multiple consecutive power control commands corresponding to that code channel. 6.4.1.1.1 Minimum requirement The BS transmitter shall have the capability of setting the inner loop output power with a step sizes of 1dB mandatory and 0.5 db optional
13 TS 25.104 v3.1.0 (1999-12) (a) The tolerance of the power control step due to inner loop power control shall be within the range shown in Table 6.1. (b) The tolerance of the combined output power change due to inner loop power control shall be within the range shown in Table 6.2. Power control commands in the down link Table 6.1: Transmitter power control step tolerance Transmitter power control step tolerance 1 db step size 0.5 db step size Lower Upper Lower Upper Up (TPC command 1 ) +0.5 db +1.5 db +0.25 db +0.75 db Down (TPC command 0 ) -0.5 db -1.5 db -0.25 db -0.75 db Power control commands in the down link Table 6.2: Transmitter combined output power change tolerance Transmitter combined output power change tolerance after 10 consecutive equal commands (up or down) 1 db step size 0.5dB step size Lower Upper Lower Upper Up (TPC command 1 ) +8 db +12 db +4 db +6 db Down (TPC command 0 ) -8 db -12 db -4 db -6 db 6.4.2 Power control dynamic range The power control dynamic range is the difference between the maximum and the minimum transmit output power of a code channel for a specified reference condition. 6.4.2.1 Minimum requirements Down link (DL) power control dynamic range: Maximum power:bs maximum output power 3 db or greater Minimum power: BS maximum output power 28 db or less 6.4.3 Total power dynamic range The total power dynamic range is the difference between the maximum and the minimum total transmit output power for a specified reference condition. Note: The upper limit of the dynamic range is the BS maximum output power. The lower limit of the dynamic range is the lowest minimum power from the BS when no traffic channels are activated. 6.4.3.1 Minimum requirement The down link (DL) total power dynamic range shall be 18 db or greater.
14 TS 25.104 v3.1.0 (1999-12) 6.4.4 Primary CPICH power Primary CPICH power is the transmission power of the Common Pilot Channel averaged over one frame. Primary CPICH power is indicated on the BCH. 6.4.4.1 Requirement CPICH power shall be within ± 2.1dB of the value indicated by a signaling message. 6.6 Output RF spectrum emissions 6.6.1 Occupied bandwidth Occupied bandwidth is a measure of the bandwidth containing 99% of the total integrated power for transmitted spectrum and is centered on the assigned channel frequency. The occupied channel bandwidth shall be less than 5 MHz based on a chip rate of 3.84 Mcps. 6.6.2 Out of band emission Out of band emissions are unwanted emissions immediately outside the channel bandwidth resulting from the modulation process and non-linearity in the transmitter but excluding spurious emissions. This out of band emission limit is specified in terms of a spectrum emission mask or adjacent channel power ratio for the transmitter. 6.6.2.1 Spectrum emission mask The mask defined in Table 6.3 to 6.6 below may be mandatory in certain regions. In other regions this mask may not be applied. For regions where this clause applies, the requirement shall be met by a base station transmitting on a single RF carrier configured in accordance with the manufacturer s specification. Emissions shall not exceed the maximum level specified by the mask in the frequency range with offset f from 2.5 MHz to f max from the carrier frequency. The maximum offset f max is either 12.5 MHz or the offset to the UMTS Tx band edge as defined in section 5.2, whichever is the greatest. Frequency offset f from the carrier [MHz] 2.5 2.7 3.5 7.5 f max -15 0 Power density in 30kHz [dbm] -20-25 -30-35 P = 39 dbm P = 43 dbm -5-10 -15-20 Power density in 1 MHz [dbm] -40 P = 31 dbm -25
15 TS 25.104 v3.1.0 (1999-12) Table 6.3: Spectrum emission mask values, BS maximum output power P 43 dbm Frequency offset f Maximum level Measurement bandwidth 2.5 f < 2.7 MHz -14 dbm 30 khz 1 2.7 f < 3.5 MHz - 14-15 ( f - 2.7) dbm 30 khz 1 3.5 f f max MHz -13 dbm 1 MHz 2 Table 6.4: Spectrum emission mask values, BS maximum output power 39 P < 43 dbm Frequency offset f Maximum level Measurement bandwidth 2.5 f < 2.7 MHz -14 dbm 30 khz 1 2.7 f < 3.5 MHz -14-15 ( f - 2.7) dbm 30 khz 1 3.5 f < 7.5 MHz -13 dbm 1 MHz 2 7.5 f f max MHz P - 56 dbm 1 MHz 2 Table 6.5: Spectrum emission mask values, BS maximum output power 31 P < 39 dbm Frequency offset f Maximum level Measurement bandwidth 2.5 f < 2.7 MHz P - 53 dbm 30 khz 1 2.7 f < 3.5 MHz P - 53-15 ( f - 2.7) dbm 30 khz 1 3.5 f < 7.5 MHz P - 52 dbm 1 MHz 2 7.5 f f max MHz P - 56 dbm 1 MHz 2 Table 6.6: Spectrum emission mask values, BS maximum output power P < 31 dbm Frequency offset f Maximum level Measurement bandwidth 2.5 f < 2.7 MHz -22 dbm 30 khz 1 2.7 f < 3.5 MHz -22-15 ( f - 2.7) dbm 30 khz 1 3.5 f < 7.5 MHz -21 dbm 1 MHz 2 7.5 f f max MHz -25 dbm 1 MHz 2 Notes: 1. The first and last measurement positions with a 30 khz filter are 2.515 MHz and 3.485 MHz 2. The first and last measurement positions with a 1 MHz filter are 4 MHz and ( f max 500 khz)
16 TS 25.104 v3.1.0 (1999-12) 6.6.2.2 Adjacent Channel Leakage power Ratio (ACLR) Adjacent Channel Leakage power Ratio (ACLR) is the ratio of the transmitted power to the power measured after a receiver filter in the adjacent channel(s). Both the transmitted power and the received power are measured through a matched filter (Root Raised Cosine and roll-off 0.22) with a noise power bandwidth equal to the chip rate. The requirements shall apply whatever the type of transmitter considered (single carrier or multi-carrier). It applies for all transmission modes foreseen by the manufacturer s specification. 6.6.2.2.1 Minimum requirement The ACLR shall be better than the value specified in Table 6.7. Table 6.7: BS ACLR BS adjacent channel offset below the first or above the last carrier frequency used ACLR limit 5 MHz 45 db 10 MHz 50 db 6.6.2.3 Protection outside a licensee s frequency block This requirement is applicable if protection is required outside a licensee s defined frequency block. 6.6.2.3.1 Minimum requirement This requirement applies for frequencies outside the licensee s frequency block, up to an offset of 12.5MHz from a carrier frequency. The power of any emission shall be attenuated below the transmit power (P) by at least 43 + 10 log (P)dB. Compliance with this provision is based on the use of measurement instrumentation employing a resolution bandwidth of 1MHz or greater. However, in the 1MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier centre frequency and one above the carrier centre frequency, outside of which all emissions are attenuated at least 26dB below the transmitter power. When measuring the emission limits, the nominal carrier frequency shall be adjusted as close to the licensee s frequency block edges, both upper and lower, as the design permits. The measurements of emission power shall be mean power. 6.6.3 Spurious emissions Spurious emissions are emissions which are caused by unwanted transmitter effects such as harmonics emission, parasitic emission, intermodulation products and frequency conversion products, but exclude out of band emissions. This is measured at the base station RF output port. Unless otherwise stated, all requirements are measured as mean power.
17 TS 25.104 v3.1.0 (1999-12) 6.6.3.1 Mandatory Requirements The requirements of either subclause 6.6.3.1.1 or subclause 6.6.3.1.2 shall apply whatever the type of transmitter considered (single carrier or multi-carrier). It applies for all transmission modes foreseen by the manufacturer s specification. Either requirement applies at frequencies within the specified frequency ranges which are more than 12.5MHz under the first carrier frequency used or more than 12.5MHz above the last carrier frequency used. 6.6.3.1.1 Spurious emissions (Category A) The following requirements shall be met in cases where Category A limits for spurious emissions, as defined in ITU-R Recommendation SM.329-7 [1], are applied. 6.6.3.1.1.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.8: BS Mandatory spurious emissions limits, Category A Band Maximum level Measurement Bandwidth Note 9kHz 150kHz 1 khz Bandwidth as in ITU-R SM.329-7, s4.1-13 dbm 150kHz 30MHz 10 khz Bandwidth as in ITU-R SM.329-7, s4.1 30MHz 1GHz 100 khz Bandwidth as in ITU-R SM.329-7, s4.1 1GHz 12.75 GHz 1 MHz Upper frequency as in ITU-R SM.329-7, s2.6 6.6.3.1.2 Spurious emissions (Category B) The following requirements shall be met in cases where Category B limits for spurious emissions, as defined in ITU-R Recommendation SM.329-7 [1], are applied. 6.6.3.1.2.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.9: BS Mandatory spurious emissions limits, Category B Band Maximum Level Measurement Bandwidth Note 9kHz 150kHz -36 dbm 1 khz Bandwidth as in ITU-R SM.329-7, s4.1 150kHz 30MHz - 36 dbm 10 khz Bandwidth as in ITU-R SM.329-7, s4.1
18 TS 25.104 v3.1.0 (1999-12) 30MHz 1GHz -36 dbm 100 khz Bandwidth as in ITU-R SM.329-7, s4.1 1GHz -30 dbm 1 MHz Bandwidth as in ITU-R SM.329-7, s4.1 Fc1-60 MHz or 2100 MHz whichever is the higher Fc1 60 MHz or 2100 MHz whichever is the higher -25 dbm 1 MHz Specification more stringent than ITU-R SM.329-7, s4.1 Fc1 50 MHz or 2100 MHz whichever is the higher Fc1 50 MHz or 2100 MHz whichever is the higher -15 dbm 1 MHz Specification more stringent than ITU-R SM.329-7, s4.1 Fc2 + 50 MHz or 2180 MHz whichever is the lower Fc2 + 50 MHz or 2180 MHz whichever is the lower -25 dbm 1 MHz Specification more stringent than ITU-R SM.329-7, s4.1 Fc2 + 60 MHz or 2180 MHz whichever is the lower Fc2 + 60 MHz or 2180 MHz whichever is the lower 12.75 GHz -30 dbm 1 MHz Bandwidth as in ITU-R SM.329-7, s4.1. Upper frequency as in ITU-R SM.329-7, s2.6 Fc1 : Center frequency of first carrier frequency used. Fc2 : Center frequency of last carrier frequency used. 6.6.3.2. Protection of the BS receiver This requirement may be applied in order to prevent the receiver of the BS being desensitised by emissions from the BS transmitter which are coupled between the antennas of the BS. This is measured at the transmit antenna port. 6.6.3.2.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.10: BS Spurious emissions limits for protection of the BS receiver Band Maximum Level Measurement Bandwidth Note 1920 1980MHz -96 dbm 100 khz For operation in Frequency Bands defined in sub-clause 5.2(a)
19 TS 25.104 v3.1.0 (1999-12) 1850-1910 MHz -96 dbm 100kHz For operation in Frequency Bands defined in sub-clause 5.2(b) 6.6.3.3 Co-existence with GSM 900 6.6.3.3.1 Operation in the same geographic area This requirement may be applied for the protection of GSM 900 MS in geographic areas in which both GSM 900 and UTRA are deployed. [This requirement assumes the scenario described in 25.942.] For different scenarios, the manufacturer may declare a different requirement. 6.6.3.3.1.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.11: BS Spurious emissions limits for BS in geographic coverage area of GSM 900 Band Maximum Level Measurement Bandwidth Note 921 960 MHz -47 dbm 100 khz 6.6.3.3.2 Co-located base stations This requirement may be applied for the protection of GSM 900 BTS receivers when GSM 900 BTS and UTRA BS are co-located. 6.6.3.3.2.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.12: BS Spurious emissions limits for protection of the BS receiver Band Maximum Level Measurement Bandwidth Note 876-915 MHz -98 dbm 100 khz 6.6.3.4 Co-existence with DCS 1800 6.6.3.4.1 Operation in the same geographic area This requirement may be applied for the protection of DCS 1800 MS in geographic areas in which both DCS 1800 and UTRA are deployed. [This requirement assumes the scenario described in 25.942.] For different scenarios, the manufacturer may declare a different requirement.
20 TS 25.104 v3.1.0 (1999-12) 6.6.3.4.1.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.13: BS Spurious emissions limits for BS in geographic coverage area of DCS 1800 Band Maximum Level Measurement Bandwidth Note 1805 1880 MHz -57 dbm 100 khz 6.6.3.4.2 Co-located base stations This requirement may be applied for the protection of DCS 1800 BTS receivers when DCS 1800 BTS and UTRA BS are co-located. 6.6.3.4.2.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.14: BS Spurious emissions limits for BS co-located with DCS 1800 BTS Band Maximum Level Measurement Bandwidth Note 1710-1785 MHz -98 dbm 100 khz 6.6.3.5 Co-existence with PHS This requirement may be applied for the protection of PHS in geographic areas in which both PHS and UTRA are deployed. 6.6.3.5.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.15: BS Spurious emissions limits for BS in geographic coverage area of PHS Band Maximum Level Measurement Bandwidth Note 1893.5 1919.6 MHz -41 dbm 300 khz 6.6.3.6 Co-existence with services in adjacent frequency bands This requirement may be applied for the protection in bands adjacent to 2110-2170 MHz, as defined in sub-clause 5.2(a) and 1930-1990 MHz, as defined in sub-clause 5.2(b) in geographic areas in which both an adjacent band service and UTRA are deployed. 6.6.3.6.1 Minimum requirement The power of any spurious emission shall not exceed:
21 TS 25.104 v3.1.0 (1999-12) Table 6.16: BS spurious emissions limits for protection of adjacent band services Band (f) Maximum Level Measurement Bandwidth Note 2100-2105 MHz -30 + 3.4 (f - 2100 MHz) dbm 1 MHz For operation in frequency bands as defined in subclause 5.2(a) 2175-2180 MHz -30 + 3.4 (2180 MHz - f) dbm 1 MHz For operation in frequency bands as defined in subclause 5.2(a) 1920-1925 MHz -30 + 3.4 (f 1930 MHz) dbm 1 MHz For operation in frequency bands as defined in subclause 5.2(b) 1995-2000 MHz -30 +3.4 (2000 MHz f) dbm 1 MHz For operation in frequency bands as defined in subclause 5.2(b) 6.6.3.7 Co-existence with UTRA-TDD 6.6.3.7.1 Operation in the same geographic area This requirement may be applied to geographic areas in which both UTRA-TDD and UTRA-FDD are deployed. 6.6.3.7.1.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.17: BS Spurious emissions limits for BS in geographic coverage area of UTRA-TDD Band Maximum Level Measurement Bandwidth Note 1900 1920 MHz -52 dbm 1 MHz 2010 2025 MHz -52 dbm 1 MHz 6.6.3.7.2 Co-located base stations This requirement may be applied for the protection of UTRA-TDD BS receivers when UTRA-TDD BS and UTRA FDD BS are co-located.
22 TS 25.104 v3.1.0 (1999-12) 6.6.3.7.2.1 Minimum Requirement The power of any spurious emission shall not exceed: Table 6.18: BS Spurious emissions limits for BS co-located with UTRA-TDD Band Maximum Level Measurement Bandwidth Note 1900 1920 MHz 86 dbm 1 MHz 2010 2025 MHz 86 dbm 1 MHz 6.7 Transmit intermodulation The transmit intermodulation performance is a measure of the capability of the transmitter to inhibit the generation of signals in its non linear elements caused by presence of the wanted signal and an interfering signal reaching the transmitter via the antenna. The transmit intermodulation level is the power of the intermodulation products when a WCDMA modulated interference signal is injected into the antenna connector at a level of 30 db lower than that of the subject signal. The frequency of the interference signal shall be ±5 MHz, ±10 MHz and ±15 MHz offset from the subject signal. 6.7.1 Minimum requirement The transmit intermodulation level shall not exceed the out of band emission or the spurious emission requirements of section 6.6.2 and 6.6.3. 6.8 Transmit modulation 6.8.1 Transmit pulse shape filter The transmit pulse-shaping filter is a root-raised cosine (RRC) with roll-off α =0.22 in the frequency domain. The impulse response of the chip impulse filter RC 0 (t) is RC 0 () t sin π = t T C t TC t 1 4α T t T 2 ( 1 α ) + 4α cos π ( 1+ α ) π t T C C C T c Where the roll-off factor α = 0.22 and the chip duration: 1 = 0.26042µ s chiprate 6.8.2 Modulation Accuracy The modulation accuracy is a measure of the difference between the measured waveform and the theoretical modulated waveform (the error vector). It is the square root of the ratio of the mean error vector power to the mean reference signal power expressed as a %. The measurement interval is one power control group (timeslot). The requirement is valid over the total power dynamic range as specifed in 6.4.3. 6.8.2.1 Minimum requirement The Modulation accuracy shall not be worse than 12.5 %.
23 TS 25.104 v3.1.0 (1999-12) 6.8.3 Peak code Domain error The code domain error is computed by projecting the error vector power onto the code domain at the maximum spreading factor. The error vector for each power code is defined as the ratio to the mean power of the reference waveform expressed in db. The peak code domain error is defined as the maximum value for the code domain error. The measurement interval is one power control group (timeslot). 6.8.3.1 Minimum requirement The peak code domain error shall not exceed -33 db
24 TS 25.104 v3.1.0 (1999-12) 7 Receiver characteristics 7.1 General The requirements in Section 7 assume that the receiver is not equipped with diversity. For receivers with diversity, the requirements apply to each antenna connector separately, with the other one(s) terminated or disabled.the requirements are otherwise unchanged. 7.2 Reference sensitivity level The reference sensitivity is the minimum receiver input power measured at the antenna connector at which the Bit Error Rate (BER) does not exceed the specific value indicated in section 7.2.1. 7.2.1 Minimum requirement For the measurement channel specified in Annex A, the reference sensitivity level and performance of the BS shall be as specified in Table 7.1. Table 7.1: BS reference sensitivity levels Measurement channel BS reference sensitivity level (dbm) BER 12.2 kbps -121 dbm BER shall not exceed 0.001 7.2.2 Maximum Frequency Deviation for Receiver Performance The need for such a requirement is for further study. 7.3 Dynamic range The receiver dynamic range is the input power range at each BS antenna connector over which the [FER/BER} does not exceed a specific rate. The static [BER/FER] reference performance as specified in clause 7.2.1 should be met over a receiver input range of [30] db above the specified reference sensitivity level for [channel type ffs]. 7.4 Adjacent Channel Selectivity (ACS) Adjacent channel selectivity (ACS) is a measure of the receiver ability to receive a wanted signal at is assigned channel frequency in the presence of an adjacent channel signal at a given frequency offset from the center frequency of the assigned channel. ACS is the ratio of the receiver filter attenuation on the assigned channel frequency to the receive filter attenuation on the adjacent channel(s). 7.4.1 Minimum requirement The BER shall not exceed 0.001 for the parameters specified in Table 7.2.
25 TS 25.104 v3.1.0 (1999-12) Table 7.2 : Adjacent channel selectivity Parameter Level Unit Data rate 12.2 kbps Wanted signal Reference sensitivity level + 6dB dbm Interfering signal -52 dbm Fuw (Modulated) 5 MHz 7.5 Blocking characteristics The blocking characteristics is a measure of the receiver ability to receive a wanted signal at its assigned channel frequency in the presence of an unwanted interferer on frequencies other than those of the spurious response or the adjacent channels; without this unwanted input signal causing a degradation of the performance of the receiver beyond a specified limit. The blocking performance shall apply at all frequencies as specified in the table below, using a 1MHz step size. 7.5.1 Minimum requirement The static reference performance as specified in clause 7.2.1 should be met with a wanted and an interfering signal coupled to BS antenna input using the following parameters. Table 7.3(a) : Blocking performance requirement for operation in frequency bands in sub-clause 5.2(a) Center Frequency of Interfering Signal Interfering Signal Level Wanted Signal Level Minimum Offset of Interfering Signal Type of Interfering Signal 1920 1980 MHz -40 dbm <REFSENS> + 6 db 10 MHz WCDMA signal with one code 1900 1920 MHz 1980 2000 MHz 1 MHz -1900 MHz, -40 dbm <REFSENS> + 6 db 10 MHz WCDMA signal with one code -15 dbm <REFSENS> + 6 db CW carrier and 2000 MHz 12750 MHz Table 7.3(b) : Blocking performance requirement for operation in frequency bands in sub-clause 5.2(b) Center Frequency of Interfering Signal Interfering Signal Level Wanted Signal Level Minimum Offset of Interfering Signal Type of Interfering Signal 1850 1910 MHz - 40 dbm <REFSENS> + 6dB 10 MHz WCDMA signal with one code 1830 1850 MHz 1910 1930 MHz 1 MHz 1830 MHz -40 dbm <REFSENS> + 6dB 10 MHz WCDMA signal with one code -15 dbm <REFSENS> + 6dB CW carrier 1930 MHz 12750 MHz
26 TS 25.104 v3.1.0 (1999-12) 7.6 Intermodulation characteristics Third and higher order mixing of the two interfering RF signals can produce an interfering signal in the band of the desired channel. Intermodulation response rejection is a measure of the capability of the receiver to receiver a wanted signal on its assigned channel frequency in the presence of two or more interfering signals which have a specific frequency relationship to the wanted signal. 7.6.1 Minimum requriement The static reference performance as specified in clause 7.2.1 should be met when the following signals are coupled to BS antenna input A wanted signal at the assigned channel frequency, 6 db above the static reference level. Two interfering signals with the following parameters. Table 7.3 : Intermodulation performance requirement Interfering Signal Level Offset Type of Interfering Signal - 48 dbm 10 MHz CW signal - 48 dbm 20 MHz WCDMA signal with one code 7.7 Spurious emissions The spurious emissions power is the power of emissions generated or amplified in a receiver that appear at the BS receiver antenna connector. The requirements apply to all BS with separate RX and TX antenna port. The test shall be performed when both TX and RX are on with the TX port terminated. For all BS with common RX and TX antenna port the transmitter spurious emission as specified in section 6.6.3 is valid. 7.7.1 Minimum requirement The spurious emission shall be: (a) Less than 78 dbm/3.84 MHz at the BS receiver antenna connector, for frequencies from 1900MHz to 1980MHz and from 2010MHz to 2025MHz. (b) Less than 57 dbm/100 khz at the BS receiver antenna connector, for frequencies band from 9kHz to 1GHz. (c) Less than 47 dbm/100 khz at the BS receiver antenna connector, for frequencies band from 1GHz to 12.75 GHz with the exception of frequencies between 12.5MHz below the first carrier frequency used, and 12.5MHz above the last carrier frequency used.
27 TS 25.104 v3.1.0 (1999-12) 8 Performance requirement 8.1 General Performance requirements for the BS are specified for the measurement channels defined in Annex A and the propagation conditions in Annex B. The requirements only apply to those measurement channels that are supported by the base station. The requirements only apply to a base station with dual receiver antenna diversity. The required E b /N 0 shall be applied separately at each antenna port. Physical channel Table 8.1: Summary of Base Station performance targets Measurement channel Static Multi-path Multi-path Multi-path Case 1 Case 2 Case 3 Performance metric Moving Birth / Death 12.2 kbps BLER<10-2 BLER<10-2 BLER<10-2 BLER<10-2 BLER< BLER< 64 kbps BLER< 10-1,10-2 BLER< 10-1, 10-2 BLER< 10-1,10-2 BLER< 10-1, 10-2,10-3 BLER< BLER< DCH 144 kbps BLER< 10-1,10-2 BLER< 10-1,10-2 BLER< 10-1,10-2 BLER< 10-1, 10-2,10-3 - - 384 kbps BLER< 10-1,10-2 BLER< 10-1,10-2 BLER< 10-1,10-2 BLER< - 10-1, 10-2,10-3 - 8.2 Demodulation in static propagation conditions 8.2.1 Demodulation of DCH The performance requirement of DCH in static propagation conditions is determined by the maximum Block Error Rate (BLER ) allowed when the receiver input signal is at a specified E b /N 0 limit. The BLER is calculated for each of the measurement channels supported by the base station. 8.2.1.1 Minimum requirement The BLER should not exceed the limit for the E b /N 0 specified in Table 8.2. Table 8.2: Performance requirements in AWGN channel. Measurement channel Required E b /N 0 Required E b /N 0 BLER < 10-1 BLER < 10-2 12.2 kbps n.a. 5.1 db 64 kbps 1.5 db 1.7 db 144 kbps 0.8 db 0.9 db 384 kbps 0.9 db 1.0 db
28 TS 25.104 v3.1.0 (1999-12) 8.3 Demodulation of DCH in multipath fading conditions 8.3.1 Multipath fading Case 1 The performance requirement of DCH in multipath fading Case 1 is determined by the maximum Block Error Rate (BLER ) allowed when the receiver input signal is at a specified E b /N 0 limit. The BLER is calculated for each of the measurement channels supported by the base station. 8.3.1.1 Minimum requirement The BLER should not exceed the limit for the E b /N 0 specified in Table 8.3. Table 8.3: Performance requirements in multipath Case 1 channel. Measurement channel Required E b /N 0 Required E b /N 0 BLER < 10-1 BLER < 10-2 8.3.2 Multipath fading Case 2 12.2 kbps n.a. 11.9 db 64 kbps 6.2 db 9.2 db 144 kbps 5.4 db 8.4 db 384 kbps 5.8 db 8.8 db The performance requirement of DCH in multipath fading Case 2 is determined by the maximum Block Error Rate (BLER ) allowed when the receiver input signal is at a specified E b /N 0 limit. The BLER is calculated for each of the measurement channels supported by the base station. 8.3.2.1 Minimum requirement The BLER should not exceed the limit for the E b /N 0 specified in Table 8.4. Table 8.4: Performance requirements in multipath Case 2 channel. Measurement channel Required E b /N 0 Required E b /N 0 BLER < 10-1 BLER < 10-2 8.3.3 Multipath fading Case 3 12.2 kbps n.a. 9.0 db 64 kbps 4.3 db 6.4 db 144 kbps 3.7 db 5.6 db 384 kbps 4.1 db 6.1 db The performance requirement of DCH in multipath fading Case 3 is determined by the maximum Block Error Rate (BLER ) allowed when the receiver input signal is at a specified E b /N 0 limit. The BLER is calculated for each of the measurement channels supported by the base station.
29 TS 25.104 v3.1.0 (1999-12) 8.3.3.1 Minimum requirement The BLER should not exceed the limit for the E b /N 0 specified in Table 8.5. Table 8.5: Performance requirements in multipath Case 3 channel. Measurement channel Required E b /N 0 Required E b /N 0 Required E b /N 0 BLER < 10-1 BLER < 10-2 BLER < 10-3 12.2 kbps n.a. 6.7 db 7.5 db 64 kbps 2.7 db 3.2 db 3.4 db 144 kbps 2.2 db 2.5 db 2.8 db 384 kbps 2.6 db 3.0 db 3.5 db 8.4 Demodulation of DCH in moving propagation conditions The performance requirement of DCH in moving propagation conditions is determined by the maximum Block Error Rate (BLER ) allowed when the receiver input signal is at a specified Eb/N0 limit. The BLER is calculated for each of the measurement channels supported by the base station. 8.4.1 Minimum requirement The BLER should not exceed the limit for the E b /N 0 specified in Table 8.6. Table 8.6: Performance requirements in moving channel. Measurement channel Required E b /N 0 Required E b /N 0 BLER < 10-1 BLER < 10-2 12.2 kbps n.a. 64 kbps 144 kbps 384 kbps 8.5 Demodulation of DCH in birth/death propagation conditions The performance requirement of DCH in birth/death propagation conditions is determined by the maximum Block Error Rate (BLER ) allowed when the receiver input signal is at a specified E b /N 0 limit. The BLER is calculated for each of the measurement channels supported by the base station.
30 TS 25.104 v3.1.0 (1999-12) 8.5.1 Minimum requirement The BLER should not exceed the limit for the E b /N 0 specified in Table 8.7. Table 8.7: Performance requirements in birth/death channel. Measurement channel Required E b /N 0 Required E b /N 0 BLER < 10-1 BLER < 10-2 12.2 kbps n.a. 64 kbps 144 kbps 384 kbps
31 TS 25.104 v3.1.0 (1999-12) Annex A (normative): Measurement channels A.1 Summary of UL reference measurement channels The parameters for the UL reference measurement channels are specified in Table A.1 and the channel coding is detailed in figure A.1 through A.5 respectively. Note that for all cases, one DPCCH shall be attached to DPDCH(s). Table A.1: Reference measuremet channels for UL DCH Parameter DCH for DTCH / DCH for DCCH Unit DPDCH Information bit rate 12.2/2.4 64/2.4 144/2.4 384/2.4 2048/2.4 kbps Physical channel 60/15 240/15 480/15 960/15 960/15 kbps Spreading factor 64 16 8 4 4 Repetition rate 22/22 19/19 8/9-18/-18-1/-1 % Interleaving 20 40 40 40 80 ms Number of DPDCHs 1 1 1 1 6 DPCCH Dedicated pilot 6 bit/slot Power control 2 bit/slot TFCI 2 bit/slot Spreading factor 256 Power ratio of -2.69-5.46-9.54-9.54-9.54 db DPCCH/DPDCH Amplitude ratio of DPCCH/DPDCH 0.7333 0.5333 0.3333 0.3333 0.3333
32 TS 25.104 v3.1.0 (1999-12) A.2 UL reference measurement channel for 12.2 kbps The parameters for the UL reference measurement channel for 12.2 kbps are specified in Table A.2 and the channel coding is detailed in Figure A.2. DTCH Uplink DCCH Information data 244 Layer 3 Max. 80 Header 16 LAC header,padding discard padding CRC detection Tail bit discard 244 260 CRC16 Tail8 CRC detection Tail bit discard 96 112 CRC16 Tail8 Viterbi decoding R=1/3 1st interleaving 804 804 Viterbi decoding R=1/3 1st interleaving 360 360 Radio Frame segmentation #1 402 #2 402 Radio Frame segmentation 90 90 90 90 Rate matching #1 4905 #2 4905 #1 4905 #2 4905 105 105 105 105 2nd interleaving slot segmentation 4905 1105 4905 1105 4905 1105 4905 1105 600 600 600 600 1 2 15 1 2 15 1 2 15 1 2 15 40 40 40 40 40 40 40 40 40 40 40 40 60kbps DPDCH 1 2 15 1 2 15 1 2 15 1 2 15 Radio frame FN=4N Radio frame FN=4N+1 Radio frame FN=4N+2 Radio frame FN=4N+3 Table A.2: UL reference measurement channel (12.2 kbps) Parameter Level Unit Information bit rate 12.2 kbps DPCH 60 kbps Power control Off TFCI On Repetition 22 %
33 TS 25.104 v3.1.0 (1999-12) A.3 UL reference measurement channel for 64 kbps The parameters for the UL reference measurement channel for 64 kbps are specified in Table A.3 and the channel coding is detailed in Figure A.3. DTCH Uplink DCCH Information data 2560 Layer 3 Max. 80 Header 16 LAC header,padding discard padding CRC detection Turbo Code R=1/3 2560 2576 7740 CRC16 Termination 12 CRC detection Tail bit discard Viterbi decoding R=1/3 96 112 360 CRC16 Tail8 1st interleaving 7740 1st interleving 360 Radio Frame segmentation Rate matching #1 1935 #2 1935 #3 1935 #4 1935 90 90 90 90 #1 22935 #2 22935 #3 22935 #4 22935 105 105 105 105 2nd interleaving 22935 1075 22935 1075 22935 1075 22935 2400 2400 2400 2400 1075 slot segmentation 1 2 15 160 160 1 2 15 1 2 15 1 2 15 160 240kbps DPDCH 1 2 15 1 2 15 1 2 15 1 2 15 Radio frame FN=4N Radio frame FN=4N+1 Radio frame FN=4N+2 Radio frame FN=4N+3 Table A.3: UL reference measurement channel (64kbps) Parameter Level Unit Information bit rate 64 kbps DPCH 240 kbps Power control Off TFCI On Repetition 19 %
34 TS 25.104 v3.1.0 (1999-12) A.4 UL reference measurement channel for 144 kbps The parameters for the UL reference measurement channel for 144 kbps are specified in Table A.4 and the channel coding is detailed in Figure A.4. DTCH Uplink DCCH Information data 2880 2880 Layer 3 Max. 80 Header 16 LAC header,padding discard padding CRC detection Turbo Code R=1/3 2880 2880 CRC16 5792 17400 CRC16 Termination 2x12 CRC detection Tail bit discard Viterbi decoding R=1/3 96 112 360 CRC16 Tail8 1st interleaving 17400 1 st interleaving 360 Radio Frame segmentation Rate matching #1 4350 #2 4350 #3 4350 #4 4350 #1 90 #2 90 #3 90#4 90 #1 4702 #2 4702 #3 4702 #4 4702 #1 98 #2 98 #3 98#4 98 2nd interleaving 4702 98 4702 98 4702 98 4702 4800 4800 4800 4800 98 slot segmentation 1 2 15 1 2 15 320 320 1 2 15 1 2 15 320 480kbps DPDCH 1 2 15 1 2 15 1 2 15 1 2 15 Radio frame FN=4N Radio frame FN=4N+1 Radio frame FN=4N+2 Radio frame FN=4N+3 Table A.4: UL reference measurement channel (144kbps) Parameter Level Unit Information bit rate 144 kbps DPCH 480 kbps Power control Off TFCI On Repetition 8 %
35 TS 25.104 v3.1.0 (1999-12) A.5 UL reference measurement channel for 384 kbps The parameters for the UL reference measurement channel for 384 kbps are specified in Table A.5 and the channel coding is detailed in Figure A.5. DTCH Uplink DCCH Information data CRC detection Turbo Code R=1/3 3840 3840 3840 3840 3840 3840 153603840 3840 15424 46320 CRC16 Termination 4 x12 Layer 3 Max. 80 Header 16 LAC header,padding discard CRC detection Tail bit discard Viterbi decoding R=1/3 96 112 padding CRC16 360 Tail8 1st interleaving 46320 1st interleaving 360 Radio Frame segmentation Rate matching #1 11580 #2 11580 #3 11580 #4 11580 #1 90 #2 90 #3 90#4 90 #1 9525 #2 9525 #3 9525 #4 9525 #1 75 #2 75 #3 75#4 75 2nd interleaving 9525 75 9525 75 9525 75 9525 9600 9600 9600 9600 75 slot segmentation 1 2 15 1 2 15 640 640 1 2 15 1 2 15 640 960kbps DPDCH 1 2 15 1 2 15 1 2 15 1 2 15 Radio frame FN=4N Radio frame FN=4N+1 Radio frame FN=4N+2 Radio frame FN=4N+3 Table A.5: UL reference measurement channel (384kbps) Parameter Level Unit Information bit rate 384 kbps DPCH 960 kbps Power control Off TFCI On Puncturing 18 %
36 TS 25.104 v3.1.0 (1999-12) A.6 UL reference measurement channel for 2048 kbps The parameters for the UL reference measurement channel for 2048 kbps are specified in Table A.6 and the channel coding is detailed in Figure A.6. DTCH Uplink DCCH Information data 4096 4096 4096 4096 x40 Layer 3 Max. 80 Header 16 LAC header,padding discard padding CRC detection Turbo Code R=1/3 4096 4096 164480 4096 494703 CRC16x40 Termination 33 x12 CRC detection Tail bit discard Viterbi decoding R=1/3 96 CRC16Tail8 112 360 1st interleaving Attach empty bits Radio Frame segmentation 494730 1 1st interleaving #1 61838 #2 61838 #8 61838 #1 90 #2 90 #3 90 #4 90 #5 90 #6 90 #7 90 #8 90 360 Rate matching #1 57516 #2 57516 #8 57516 #1 84 #2 84 #3 84 #4 84 #5 84 #6 84 #7 84 #8 84 2nd interleaving 57516 84 57516 84 57516 84 slot segmentation (Into 6 segments) 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 960kbps DPDCH (6 code multiplex Tx.) 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 9600 1 2 15 1 2 15 1 2 15 1 2 640 640 15 640 1 2 15 1 2 15 1 2 15 1 2 15 Radio frame FN=8N Radio frame FN=8N+1 Radio frame FN=8N+3 Table A.6: UL reference measurement channel (2048kbps) Parameter Level Unit Information bit rate 2048 Kbps DPCH 960 Kbps Power control Off TFCI On Puncturing 1 %