name: TKF article number: 10305 description Nr.: POE- PS- 10305 PT F F F 800 B C 1 2 3 4 5 6 7 Assembly: 1. Primary tube 5 mm 2. CAT 5 E FTP cable 3. CAT 5 E FTP cable 4. Bus cable 5. Coax 9 cable 6. Separation foil 7. PVC sheath 8. CAT 5 E FTP cable 8 The TwenCombi cable is a stranded assembly of different types of cable. A separation foil is applied around this assembly to avoid bonding between the different components and outer sheath. Telephone number: +31 (0)53 572255 Signal cables and primary tube Foil Outer Sheath - Material - Colour Diameter over core Thickness PVC sheath Diameter TwenCombi Weight TwenCombi Details can be found in the sequence sheets PET-foil is wrapped around the core to avoid bonding of the different components with the outer sheath. PVCmb Orange (RAL 2003) 16.1 mm 1.2 mm 18.5 mm 254 kg/km (approx.) Mechanical specification Tensile load Bending radius - Text - Frequency Pulling by hand only 200 mm [distance mark] TKF Hager Tehalit KISS DATA CARE - [year] [TKF ordernumber] twice every metre (distance mark only once) Created: 10 July 2003 Originator: A. Kerstens Modified: 18 November 2003 Appr. auth.: L. Pots Page 1 / 6
Nr.: POE-PS- 10305 Coax 9 5 4 3 2 1 1. Inner conductor 2. Insulation 3. Outer conductor 4. Braid 5. Outer sheath The Coax 9 is used for in-house applications for the benefit of CATV, DVB-T and T-DAB. Thanks to the screen attenuation the cable is suitable to apply in combination with digital TV and also for internet connections via the cable. Insulation Soft-annealed electrolytic copper, solid conductor Foam Polyethylene Outer conductor Copper foil under bare copper braid. Outer sheath PE compound - Colour Black Diameter insulation Diameter over braiding Diameter outer sheath Electrical specification Characteristic impedance Attenuation at (nominal) Return loss 5 MHz 50 MHz 100 MHz 200 MHz 400 MHz 862 MHz 1000 MHz 1350 MHz 1600 MHz 1750 MHz 2150 MHz 2550 MHz 3000 MHz 5-30 MHz 30-470 MHz 470-862 MHz 862-2150 MHz 1.13 mm 4.8 mm 5.4 mm 6.8 mm 75 ± 3 Ω 1.2 /100m 3.9 /100m 5.5 /100m 7.9 /100m 11.7 /100m 17.0 /100m 18.4 /100m 21.7 /100m 23.7 /100m 25.1 /100m 28.2 /100m 30.8 /100m 33.5 /100m 26 23 20 18 Screening factor 80 Capacitance 52 nf/km Page 2 / 6
Velocity ratio 85 % DC resistance at 20 O C - Inner conductor 18 Ω/km - Outer conductor 17 Ω/km Test voltage 1500 V (DC) Nr.: POE-PS- 10305 Mechanical characteristics Bending radius Pulling force Weight Environmental conditions Storage and service temperature Temperature during installation Frequency 35 mm 150 N 37 kg/km -25 / 70 O C -5 / 60 O C TKF COAX-9 [year] Every meter CAT5E FTP 4x2xAWG24/1 Three times 1 2 3 4 1. Conductor 2. Core 3. Aluminium Foil 4. PVC sheath Category 5 Enhanced Foiled Twisted Pair cable is a network cable that consists of four twisted pairs of copper wire. Cat-5E cabling supports frequencies up to 100 MHz and speeds up to 1 Gbps. It can be used for ATM, token ring, 1000Base-T, 100Base-T, and 10Base-T networking. Core Copper Polyethylene insulation - Colour code Blue-Blue/White, Orange-Orange/White, Green-Green/White, Brown-Brown/White Foil Aluminium, longitudinal under copper braid (coverage ca. 65%) Outer sheath - Sheath colour PVCmb Green (Ral6016), Blue (Ral5015) or Grey (Ral7032) Sheath Mechanical characteristics 0.52 5.5 mm (24 AWG) mm (nominal) Page 3 / 6
Nominal weight 45 kg/km Nr.: POE-PS- 10305 Electrical specification (20 O C) Conductor resistance 170 Ω/km Insulation resistance 5 GΩ km Capacitance 160 pf/100m Char. Impedance (1 100 MHz) 100 ± 15 Ω Char. Impedance (100 200 MHz) 100 ± 18 Ω Att. NEXT PS-Next ELFEXT PS- ELFEXT PS-ACR /100 m /100 m /100 m Frequency 1 MHz 2,1 71 69 69 66 67 4 MHz 4,1 62 60 57 54 56 10 MHz 6,4 56 54 49 46 48 16 MHz 8,0 53 51 45 42 43 20 MHz 9,0 51 49 43 40 41 31,25 MHz 11,4 49 47 39 36 35 62,5 MHz 16,3 44 42 33 30 26 100 MHz 21,0 41 39 29 26 18 125 MHz 24,0 39 37 27 23 14 Frequency EIB Bus cable TKF KISS DATA Cat5e FTP [year] Twice every meter 5 4 3 2 1 1. Conductor 2. Insulation 3. Tape 4. Drain wire 5. Outer sheet Installation bus cable (EIB: European Installation Bus) for decentralised control of lighting, heating, air-conditioning, ventilation, energy etc. in buildings. Insulation Solid plain copper PVC - Colour Black, yellow, red, white - Assembly Bunched into quad Tape Cable core covered with PET tape Drain wire Drain wire included for grounding purposes Sheath Green PVC (Ral 6018) Outer sheath 0.8 4.8 mm (nominal) mm (nominal) Electrical specification Page 4 / 6
Nr.: POE-PS- 10305 Loop resistance of the core (20 O C) Conductor insulation resistance Capacitance (800 Hz) Capacity unbalance Breakdown test (50 Hz, 1 min.) Voltage rating Mechanical characteristics Minimum bending radius Nominal weight Environmental conditions Operating temperature Installation temperature Frequency 73.2 Ω/km 100 MΩ/km 100 nf/km 300 pf/100m 4000 VAC 150 VAC 10 x diameter 37 kg/km -30 O C / +70 O C - 5 O C / +50 O C [distance mark] TKF EIB [year] [TKF ordernumber] Twice every meter (distance mark only once) Primary tube 5 mm The Primary tube can be used as a fibre pathway. The inner wall is provided with a low friction layer that enhances the blowing capacity when a fibre unit is blown into the primary tube. 1 2 1 5mm PE Primary Tube 2 Low friction inner layer Tube material Tube inner surface Outer diameter Inner diameter Ratio of minimum to maximum wall thickness at any point Tube mass 100% virgin PE material Exhibit low friction characteristics 5.0 mm ± 0.1 mm; fits std push connectors 3.5 mm ±0.1 mm; measured by plug gauge > 0.9 10 g/m nominal Page 5 / 6
Nr.: POE-PS- 10305 Mechanical specification Details of test procedures can be found in [1]. Pull strength Minimum bending radius Flexibility (IEC 60794-1-2 E11) Pressure Friction Crush (IEC 60794-1-2 E3) Ice withstand Stress crack (ESCR of BS 6469 M.2) Detailed specifications 100 N, by hand only 50 mm 10 turns around mandrel of diameter 50 mm during 30 minutes shall cause no kink or damage to the tube. A tube sample shall withstand, under water, 17 bars air pressure for 2 hours without leaks. The friction-coefficient calculated with the formula: T1 logn T2 F = shall not exceed 0.11 when a fibre 7.85 unit is loaded with 500g. A sample is loaded with 100 kg for 60 seconds. After removing of the load residual deformation shall not exceed 15% measured within 1 hour of unloading. Three 1.5 m samples of tube filled with water, both ends sealed and left at 15 O C for 10 hours shall not burst or split. After this, the ice shall be left to melt, the tubes shall be emptied of water and shall withstand an instantaneous air pressure of 17 bar under water with no leaks. Five samples of tube to be tested shall not show failure before 500 hours. Ref. Description Document Originator [1] Test specification primary tube POE-PS-500099 TKF Additional information Contact the telephone number below to obtain additional information related to this specification: Page 6 / 6