Ingoing tilt-turn window type BSI, UNI-JET S-CONTURA Instructions for the use and maintenance Ventilation in tilt position, cleaning in turn position. When the handle turns downwards, the window is closed. If the handle is turned 90 the window can be tilted inwards. When the casement is pressed against the frame and the handle is turned 90 upwards the window can be opened sideways. This and the following three illustrations show how the frame pressure can be increased or reduced: Fig. 4 shows the adjustment of the upper locking points at the lock side. Fig. 5 shows the adjustment of the frame pressure in the lower bearing points. At the underside of the casement there are further locking points, where the frame pressure can be adjusted. At the underside of the shear there is an eccentric bolt where the frame pressure can be adjusted. This and the following three illustrations show how the rebate air between the casement and the frame can be adjusted: Fig. 8 shows the sideways adjustment of the rebate air. Fig 9 shows the vertical adjustment of the rebate air. This illustration shows the sideways adjustment of the rebate air on the upper bearing point. Casements with a mishandling device can be raised a bit at the lock side when closing the window. The distance can be adjusted. All moving parts must be lubricated once a year. The outlet rail in the lower casement must be cleaned as needed so that it does not clog. SKANDI BESLAG A/S Møllehaven 20 DK-4040 Jyllinge Tel. +45 4678 9600 Fax +45 4673 1710 mailbox@skandi.dk

Adjustment Page 19 Of Sliding door Adjustment of STOP Alu-rail internal

Akzo Nobel, industrial coatings system for wooden components on windows and doors offer beautiful colours and added durability. kastrupvinduet.dk Products coated with Akzo Nobel Industrial Coating System, provides maximum durability and life expectancy. Surface treatment: The timber substrates of the windows and doors are treated according to DVC technical requirements against blue stain. Coatings system: The water based coatings system is a 2 coat treatment, which are based acrylic binders. The coatings system is applied by spraying which in turn leaves the surface very smooth with good filling properties, film build and a sheen level of approximately 20. The coatings system is tested according to EN152 and EN927-3 Surface treatment with Akzo Nobel Industrial Coating System offers a number of advantages: tics, i.e. retention of gloss, and resistance to cracks. the end grain etc., which maximises the protection against moisture ingress, and results in a longer durability. Maintenance of products treated with Akzo Nobel Industrial Coating System: Opaque system: Lightly sand the surface, using a sanding pad P180 and wash down the surface with clean water and allow to fully dry prior to the application of 1-2 coats of Sikkens BL Opaque. In case of deterioration back to bare timber, sand the surface thoroughly P180/ P220 and prime with 2 coats of Cuprinol Wood Preserver Clear, followed by 1-2 coats of Sikkens BL Opaque. Translucenst system; Lightly sand the surface, using a sanding pad P180 and wash down the surface with clean water and allow to fully dry prior to the application of 1-2 coats of Sikkens Cetol BL 31. In case of deterioration back to bare timber, sand the surface back to bare timber and primed with 2 coats of Cuprinol Wood Preserver, followed by 1-2 coats of Sikkens Cetol BL 21+ Maintenance: In case of damages to the surface coating it should be repaired immediately and in case of signs of breakdown and deterioration maintenance The colours shown are a representation of the actual paint colour on the timber but are only as accurate as the printing process will allow and are therefore only given as a guide. 9010 9001 7035 7042 7016 9005 8016 TS5766 TS7536 White Oak Teak Ellehammervej 5 DK 7430 Ikast Telefon +45 96 60 20 17 www.akzonobel-wood.com Clear lacquer TRÆ Bredgade 52 7480 Vildbjerg Tlf. 9621 4000 Fax 9621 6000 trae@kastrupvinduet.dk TRÆ-ALU Fabriksvej 5 7800 Skive Tlf. 702 66 702 Fax 702 26 702 traealu@kastrupvinduet.dk KASTRUP A/S CVR-nr: 25473434 PLAST Mosebyvej 40 7500 Holstebro Tlf. 9742 1500 Fax 9742 3000 plast@kastrupvinduet.dk akzo nobel_forside_uk_ny.indd 1 10/03/11 11.21

Page 26 Annex 6 Oil for hardwood windows and doors Hardwood is a beautiful and harmonious timber it has got a natural glow and depth which becomes even more prominent when treated with oil specially developed for this type of wood. Hardwood is naturally very durable, but regular maintenance is required in order to maintain good characteristics and great appearance of hardwood. If the wood dries out the products quality can be affected. Your new hardwood windows and doors have been treated with a water based hardwood oil from Akzo Nobel. The oil penetrates the wood and gives it a water repellent surface that will last for many years as long as you repeat the treatment. The oil is industrially applied from the factory, which means that it has been applied to all visible as invisible surfaces for optimum protection of the timber. The factory applied oil is a basic treatment which helps to protect the wood surface during and immediately after installation. It is therefore recommended to apply 1 to 2 coats of Sadolin hardwood oil immediately after installation of windows and doors. The number of treatments with hardwood oil depends on how dark you want the surface. Depending on how exposed your windows are you might find it necessary to treat your windows and doors twice a year with a good quality hard wood oil.