IP65 IP67 SPECIFICATION MODEL OUTPUT INPUT PROTECTION OTHERS NOTE -2-5 -20-24 -30-36 -42-48 DC VOLTAGE 2V 5V 20V 24V 30V 36V 42V 48V CONSTANT CURRENT REGION Note.4 6 ~2V 7.5 ~ 5V 0~20V 2~24V 5~30V 8~36V 2~42V 24~48V RATED CURRENT 22A 9A 5A 3.34A 0.7A A 7.65A 6.7A RATED POWER 264W 285W 300W 320.6W 32W 320.4W 32.3W 32.6W RIPPLE & NOISE (max.) Note.2 50mVp-p 50mVp-p 50mVp-p 50mVp-p 200mVp-p 250mVp-p 250mVp-p 250mVp-p VOLTAGE ADJ. RANGE Note.6 0.8 ~ 3.5V 3.5 ~ V ~22V 2~26V 26~32V 32~39V 38~V 43~52V CURRENT ADJ. RANGE Can be adjusted by internal potentiometer A type and C type only ~ 22A 9.5 ~ 9A 7.5 ~ 5A 6.67 ~ 3.34A 5.35 ~ 0.7A 4. ~ A 3.8 ~ 7.65A 3.35 ~ 6.7A VOLTAGE TOLERANCE Note.3 3.0% 2.0%.5%.0%.0%.0%.0%.0% LINE REGULATION LOAD REGULATION 2.0%.5%.0% SETUP, RISE TIME Note.8 2500ms, 80ms at full load 230VAC /5VAC HOLD UP TIME (Typ.) VOLTAGE RANGE 5ms at full load Note.5 ~ 305VAC 230VAC /5VAC 27 ~ 43VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.98/5VAC, PF>0.95/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve) EFFICIENCY (Typ.) (230Vac) EFFICIENCY (Typ.) (277Vac) 9% 9.5% 92.5% 93% 93.5% 94% 94% 94.5% 94% 94.5% 94.5% AC CURRENT (Typ.) 3.5A / 5VAC.65A / 230VAC.A / 277VAC INRUSH CURRENT( Typ.) LEAKAGE CURRENT OVER CURRENT SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE SAFETY STANDARDS EMC IMMUNITY MTBF DIMENSION PACKING <0.75mA / 277VAC 95 ~ 08% Note.4 Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed. 4 ~ V.5 ~ 2V 22.5 ~ 27V 27~33V 33~37V 40~46V 46.5 ~ 53V 53.5~60V 59~65V Protection type : Shut down and latch off o/p voltage, re-power on to recover 00 0 (RTH2) Protection type : Shut down and latch off o/p voltage, re-power on to recover WORKING TEMP. -40 ~ +70 (Refer to "Derating Curve") WORKING HUMIDITY 20 ~ RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80, 0 ~ RH TEMP. COEFFICIENT 0.03%/ (0 ~ 50 ) VIBRATION 0 ~ 500Hz, 5G 2min./cycle, period for 72min. each along X, Y, Z axes WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMC EMISSION COLD START 70A(t width=00 s measured at I peak) at 230VAC UL8750, CSA C22.2 No. 250.0-08, EN6347-, EN6347-2-3 independent, IP65 or IP67, J6347-, Note.7 J6347-2-3 approved ; design refer to UL60950-, TUV EN60950- I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500VDC / 25 / RH Compliance to EN5505, EN55022 (CISPR22) Class B, EN6000-3-2 Class C ( load) ; EN6000-3-3 Compliance to EN6000-4-2,3,4,5,6,8,, EN6547, EN55024, light industry level (surge 4KV), criteria B 57.K hrs min. MIL-HDBK-2F (25 ) **mm (L*W*H).88Kg; 8pcs/6Kg/0.92CUFT -54 54V 27 ~ 54V 5.95A 32.3W 350mVp-p 49 ~ 58V 2.97 ~ 5.95A.0%
Mechanical Specification Case No.202A Unit:mm Blank:() IP67 rated. Cable for I/O connection. A Type:(-_A) 40 0 4 : Max. Case Temperature. Io Vo ADJ. ADJ. : Max. Case Temperature. IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.)
B Type:(-_B) 4 0 SJTW 8AWG 2C DIM+(Blue) DIM-(White) : Max. Case Temperature. C Type:(-_C) I/P 40 4. 5 4.5 9.2 5 2 3 65 Io Vo ADJ. ADJ. 2 O/P 7.5 237 : Max. Case Temperature. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) AC Input Terminal Pin No. Assignment Pin No. 2 3 Assignment FG AC/L AC/N DC Output Terminal Pin No. Assignment Pin No. Assignment +V 2 -V
D Type(option):(-_D) 4 0 : Max. Case Temperature. IP67 rated. Timer dimming function. Block Diagram Fosc : 65KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. +V -V DIM+ DIM- (B Type) Derating Curve Static Characteristics 00 80 230VAC 00 80 60 0VAC 70 LOAD (%) 40 20 LOAD (%) 60 50 40-40 -25-0 0 5 30 50 60 70 (HORIZONTAL) 00 25 35 55 65 5 80 200 230 305 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz
Power Factor Characteristic PF 0.98 0.96 0.94 0.92 0.9 0.88 0.86 0.84 Constant Current Mode % LOAD (320W) 277VAC 230VAC 5VAC EFFICIENCY vs LOAD (48V Model) series possess superior working efficiency that up to can be reached in field applications. EFFICIENCY (%) 97 95 93 9 89 87 85 83 8 79 77 75 0% % LOAD 277VAC 230VAC 5VAC DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. LED & LED's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B). 00 Vo(%) (A) Constant Voltage area (B) Constant Current area 50 (C) Hiccup Protection 50 95 Io (%) Typical LED power supply I-V curve
DIMMING OPERATION (for B-type only) DIM+(Blue) DIM-(White) Built-in 3 in dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or ~ 0Vdc or 0V PWM signal between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-V". Reference resistance value for output current adjustment (Typical) Single driver Resistance value Multiple drivers (N=driver quantity for synchronized dimming operation) Percentage of rated current 0K 0K /N 20K /N 30K /N 40K /N 50K /N 60K /N 70K /N 80K /N K /N 00K /N 0% 60K V 2V 3V 4V 5V 6V 7V 8V 9V 0V 0% 20K 30K 40K ~ 0V dimming function for output current adjustment (Typical) Dimming value Percentage of rated current 50K 70K 80K K 00K OPEN % % ----- ~08% OPEN ~08% 0V PWM signal for output current adjustment (Typical): Frequency range :00HZ ~ 3KHz Duty value 0% % OPEN Percentage of rated current 0% % ~08% Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the LED power supply unit. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. Dimming connection diagram for turning the lighting fixture ON/OFF : N FG L Relay Switch Adjuster 0~00K Ohms resistance ~0V DC Voltage 0V PWM Signal Green/ Yellow Brown Blue AC/L AC/N BType DIM+ DIM- V(-) V(+) Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture..output constant current level can be adjusted through output cable by connecting a resistance or ~0Vdc or 0V PWM signal between DIM+ and DIM-. 2.The LED lighting fixture can be turned ON/OFF by the switch.
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of to operate in dry/wet/damp or outdoor environment. AC source I/P O/ P Size Pin Configuration (Female) Size Pin Configuration (Female) M2 Order No. Suitable Current 4-PIN 5A/PIN 5-PIN 5A/PIN M5 M2-04 M2-05 Order No. 0A max. 0A max. Suitable Current 2-PIN 2A/PIN M5-02 2A max. LED Lamp Cable Joiner 66 26 20 CJ04- suitable for 4AWG~6AWG CJ04-2 suitable for 8AWG~22AWG 25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. Junction Box(Option ) 387.2 76 0 5 6 8.5 32 8.5 6 2-5 3- PF /2" 3- PF /2" 50 20 50 20 35 Optional junction box available for A / Blank - type, please contact LED & LED for details. 86